Jenn-Air CVE3401B, JED8430ADB, JED8430ADQ, JED8430ADW, JED8430BDB Installation Guide

RadiantD°wndraftC°°kt°pI JENN-AIR01

ModelJED8430 403WESTFOURTHSTREETNORTH.NEWTONA_020

INSTALLER - SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

Installation should be performed only by an authorized Jenn-Air Service Contractor or other qualified installer.
Read Safety Precautions in the Use & Care Manual before using this appliance,

INSTRUCTIONS TO INSTALLER: Side Clearance - Unit may be safely installed as near as O" (0 cm) from a side wall
if space limitations requires. However, a side clearance of at least 6" (15.24 cm) is recommended for optimum ventilation.

NOTICE TO INSTALLER: Leave these instructions with the appliance.
NOTICE TO CONSUMER: Retain these instructions for future reference.

29 3/4 o

[75.27 cm]

22"

[55.88 cm]

10"

[25.40 cm] 44

SELECT APPROPRIATE

DUCT CUTOUT.

BLOWER MAY BE ROTATED

FOR HORIZONTAL OR

VERTICAL DIRECTION BY

LOOSENING NUTS AROUND

THE BLOWER INLET.

(SEE DUCTING INSTRUCTIONS,)

l € 5/8"

11.75cm

Min. Cleoronce l

Required

17 1/2 °

[44.46 cm]

1

2"[5.08 an] MIN_

MINIMUM CABINET

TO MOTOR CLEARANCE

FOR COOLING PURPOSE.

28 7/8" _1/16 •

[73.05cm_.16 cm]

[75.27 cm]

12 1/2"

[31.76 cm]

21 1/8" ±1/8"

[53.66cm±.32 cm]

CUTOUT

DIMENSIONS

29 3/4 °

LJ

1/2o._..,=

[31.75cm]

8101 P419-60

(01-03-01)

Installing Cabinetry Over Your
Cooktop

A = 30" (76.2 cm) minimum clearance between the top of

the cooktop and the bottom of an unprotected wood
or metal cabinet.

A = 24" (60.96 cm) minimum when bottom of wood or

metal cabinet is protected by not less than 1/4"
(0.635 cm). FLAME RETARDANT millboard covered

with not less than no. 28 MSG sheet steel, 0.015"

(0.038 cm) stainless steel, 0.024" (0.061 cm)

aluminum or copper.

* To eliminate the risk of burns or fire by reaching over

heated surface units, cabinet storage space located

above the surface units should be avoided. If cabinet
storage is to be provided, the risk can be reduced by

installing a range hood that projects horizontally a
minimum of 5 inches beyond the bottom of the cabinets.

DOTTED LINES

INDICATE

RANGE HOOD

CONSTRUCTION.._

t ....

A _

Electrical Wiring Information

The neutral of this unit is grounded to the frame through
the green grounding wire. If used on new branch-circuit

installations (1996 NEC), mobile homes, recreational
vehicles, or in an area where local codes prohibit

grounding through the neutral conductor, untwist or
disconnect the green wire and connect the green wire to

ground in accordance with local code. Connect the white
neutral to the service neutral. Connect all wires to the

branch circuit with approved connectors. Use copper or
aluminum wire. If aluminum wire is used, use connectors

recognized for joining aluminum to copper.

Proper Electrical Supply

You must provide an adequate electrical supply system
as required for your cooktop. All wire connections must be

in accordance with local codes and properly insulated.
Check with local utility for governing electrical codes and

ordinances. In the absence of local electrical codes, the
National Electrical Code, NFPA No. 70, governing electric

range installations must be followed. A copy of the
National Electrical Code, NFPA No. 70, can be obtained

by writing to:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

I

k__--._-._

Installer Installation Suggestions

1. Chamfer all exposed edges of decorative laminate to

prevent damage from chipping.

2. Radius corners of cutout and file to insure smooth

edges and prevent corner cracking,

3. Rough edges, inside corners which have not been
rounded and forced fits can contribute to cracking of

the countertop laminate.

4. Countertop must be supported within 3" (7.62 cm) of
cutout.

CAUTION

warranty is Void on equipment installed other

than as recommended by manUfacturer! I

A three-wire, single phase, A.C. 120/240 volt 60 cycle

electrical system (properly circuit protected to meet Local
Codes of NFPA No. 70) must be provided. Unit must be

properly grounded in accordance with local wiring code.
The chart below recommends the minimum circuit

protector and wire size if the appliance is the only unit on
the circuit. If smaller sizes of wire are used, the unit

efficiency will be reduced and a fire hazard may be
created. It is advisable that the electrical wiring and
hookup be accomplished by a competent electrician.

RECOMMENDED MINIMUM

K.W. RATING CIRCUIT PROTECTION WIRE SIZE

ON SERIAL PLATE IN AMPERS (AWG)

0- 4.9 20 12

5.0- 6.9 30 10

7.0 - 9.9 40 8

10.0 - 11.9 50 8

12.0 - 14.9 60 6