JENN-AIR JEC8430BDS, JEC8430BDW, JEC8430BDB, JEC8430BDF Dimension Guide
JENN-AIR® DETAILED PLANNING DIMENSIONS
A
A
H
B
A
F
G
H
B
C
J K
E
LM
D
I
30" ELECTRIC RADIANT COOkTOP
JEC8430BD – 297⁄8" x 41⁄8" x 211⁄2"
PRODUCT DIMENSIONS
MODEL # JEC8430BD
Overall width
A
Overall depth
B
TOP VIEW
C
B
G
I
J K
D
E
F
Distance to control cover plate
C
Width of control cover plate
D
Distance to center of electrical conduit
E
Width of recessed cooktop
F
Height of cooking surface
G
Height with knobs
H
Height of recessed cooktop
I
Recessed height including control cover plate
J
Recessed height including electrical conduit
K
Depth of control cover plate
L
Depth to center of electrical conduit
M
Depth of recessed cooktop
N
1 of 4
in cm
7
⁄8 76.0
29
1
⁄2 54.6
21
7
⁄8 25.0
9
1
⁄8 20.5
8
5
⁄8 27.0
10
5
⁄8 72.8
28
1
⁄4 0.6
1
⁄2 3.7
1
3
⁄4 7.0
2
3
⁄4 9.5
3
1
⁄8 10.5
4
13 33.0
2 5.0
1
⁄4 51.5
20
FRONT VIEW
B
N
SIDE VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120041A 07/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
D* G
E
A
B
B
C
e
F
Side
Cabinet
G
BB
H
Side
Cabinet
30" ELECTRIC RADIANT COOkTOP
JEC8430BD – 297⁄8" x 41⁄8" x 211⁄2"
OPENING/CLEARANCE DIMENSIONS
MODEL # JEC8430BD
Width of combustible area above
A
cooking surface (min.)
Width from cooktop to fixed wall
B
or other combustible material (min.)
Recommended width to outer edge of outlet 10 25.4
C
Height to bottom of uncovered wood or
D*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
E
or metal cabinet (min.)
Recommended height to top edge of outlet 12 30.5
F
Depth of upper cabinet 13 33.0
G
Depth from cutout to wall (min.)
H
Width of cutout 29
I
Depth of cutout 20
J
Depth from cutout to front of countertop 2
K
e
Recommended electrical access location
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet
is covered by not less than
less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
If installing a hood or microwave hood combination above the cooktop, follow the
hood or microwave hood combination instructions for dimensional clearances above
the cooking surface.
ELECTRICAL REQUIREMENTS
240 volt, 60 Hz, 40-amp fused, grounded circuit is required. A dedicated circuit
is recommended. 48" (121.9 cm) of 1⁄2" (1.3 cm) I.D. flexible cable is provided.
LOCATION REQUIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider
than the cutout.
• If cabinet has a drawer, allow a 41⁄2" (11.4 cm) minimum clearance between
countertop and top of drawer.
COOKTOP OVER SINGLE WALL OVEN INSTALLATION
REQUIREMENTS
• For approved model number combinations, refer to the under counter
label on the bottom of the cooktop burner box.
• To install a cooktop over a single wall oven, refer to page 3.
FRONT VIEW
D*
Side
Cabinet
G
A
E
F
e
C
in cm
30 76.2
0 0.0
30 76.2
18 45.7
3
⁄4 1.9
1
⁄8 74.0
3
⁄8 51.9
1
⁄8 5.4
1
⁄4" (0.6 cm) flame retardant millboard covered with not
2 of 4
H
I
SIDE VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
TOP VIEW – CUTOUT
H
J
K
JRC120041A 07/2012
Loading...