JennAir JDPSG244LS, JDPSS246LM, JDPSS246LL INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

OWNER’S MANUAL

MANUEL DE L’UTILISATEUR

MANUAL DEL PROPIETARIO

TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE

DISHWASHER MAINTENANCE ......3

DISHWASHER LOADING TIPS ........4

DISHWASHER CARE ....................... 5

DISHWASHER SETTING MENU ......6

ERROR CODES ................................ 7

Error codes / blinking lights .................. 7

INSTALLATION REQUIREMENTS ...8

Tools and parts .....................................8

Location requirements ........................10

Product and cabinet opening

dimensions: .........................................11

Drain requirements .............................12

Water supply requirements .................12

Electrical requirements .......................12

INSTALLATION INSTRUCTIONS ...13

Prepare cabinet opening—

new utilities ......................................... 13

Install optional moisture barrier recommended for wood countertops ...13

Electrical connection ..........................14

Prepare dishwasher ............................15

Remove access panel and insulation ....15

Disconnect and remove drip tray

assembly ............................................. 15

Connect water line to ll valve ............ 16

Connect ll hose to ll valve ............... 17

Drain hose connection ........................ 18

Power cord connection ....................... 18

Install door handle

(on some models) ...............................20

Place dishwasher in cabinet ............... 20

Custom panel installation

(custom panel models only) ................ 21

Choose anchor attachment method ... 21

Final installation check........................22

Secure dishwasher in cabinet

opening ............................................... 23

Connect water line to house

shut-off valve ......................................24

Connect drain hose ............................24

Complete installation .......................... 26

Check operation .................................27

Install access panels ........................... 27

If dishwasher does not operate ..........28

W11323304D

ENTRETIEN DU

LAVE-VAISSELLE ........................... 30

CONSEILS DE CHARGEMENT

DU LAVE-VAISSELLE ....................31

ENTRETIEN DU

LAVE-VAISSELLE ........................... 32

MENU DE RÉGLAGE DU

LAVE-VAISSELLE: ......................... 33

CODES D’ANOMALIES ..................34

Codes d’anomalies/témoins

qui clignotent ......................................34

EXIGENCES D’INSTALLATION .....35

Outils et pièces ................................... 35

Exigences d’emplacement .................37

Dimensions d’ouverture du produit

et de l’armoire: ................................... 38

Exigences d’évacuation ...................... 39

Spécications de l’alimentation

en eau ................................................. 39

Spécicationsélectriques ................... 39

INSTRUCTIONS D’INSTALLATION ...40

Préparation de l’ouverture d’encastrement de l’armoire – nouveaux raccordements de service ... 40 Installer la barrière anti-humidité en option – recommandée pour

les comptoirs en bois .........................40

Raccordement électrique....................41

Préparation du lave-vaisselle .............. 42

Retrait du panneau d’accès

et de l’isolation ................................... 42

Débrancher et enlever le plateau

d’écoulement ...................................... 42

Branchement de l’arrivée d’eau

à la valve de distribution ..................... 43

Branchement du tuyau de remplissage

à la valve de distribution ..................... 44

Raccord du tuyau de vidange ............. 45

Branchement du cordon

d’alimentation .....................................45

Installer la poigne de porte

(sur certains modèles) ......................... 47

Placer le lave-vaisselle dans l’armoire ... 47 Installation du panneau personnalisé (modèles avec panneau personnalisé

seulement) ..........................................48

Choix de l’option de xation ............... 48

Vérication nale de l’installation ........49

Fixation du lave-vaisselle dans l’ouverture d’encastrement

de l’armoire ......................................... 50

Branchement de l’arrivée d’eau

au robinet d’arrêt de la maison ...........51

Raccordement du tuyau de vidange ... 51

Terminer l’installation ..........................53

Contrôle du fonctionnement ............... 54

Installation des panneaux d’accès .....54

Si le lave-vaisselle ne fonctionne pas ...55

MANTENIMIENTO DE

LA LAVAVAJILLAS .........................57

CONSEJOS PARA CARGAR

LA LAVAVAJILLAS .........................58

CUIDADO DE LA LAVAVAJILLAS ... 59 MENÚ DE AJUSTES DE

LA LAVAVAJILLAS: ........................60

CÓDIGOS DE ERROR ....................61

Códigos de error / Luces

parpadeantes ...................................... 61

REQUISITOS DE INSTALACIÓN ... 62

Herramientas y piezas ........................62

Requisitos de ubicación .....................64

Dimensiones del producto

y de la abertura del gabinete: ............. 65

Requisitos de desagüe .......................66

Requisitos de suministro de agua ......66

Requisitos eléctricos...........................66

INSTRUCCIONES

DE INSTALACIÓN ..........................67

Preparación de la abertura del

gabinete: instalaciones nuevas ........... 67

Instalación opcional de la barrera contra la humedad (recomendado

para los mostradores de madera) ....... 67

Conexión eléctrica .............................. 68

Prepare la lavavajillas ..........................69

Retire el panel de acceso

y el aislante ........................................ 69

Desconecte y retire el ensamblaje

de la bandeja de goteo ....................... 69

Conecte la tubería de agua

a la válvula de llenado.........................70

Conecte la manguera de llenado

a la válvula de llenado.........................71

Conexiones de la manguera

de desagüe ......................................... 72

Conexión del cable de alimentación ...72 Instale la manija de la puerta

(en algunos modelos) .......................... 74

Coloque la lavavajillas en el gabinete . 74 Instalación del panel a la medida (en modelos con paneles a la medida

solamente) ..........................................75

Selección del método de sujeción

de anclaje ............................................75

Vericación nal de la instalación .......76

Asegure la lavavajillas en la abertura

del gabinete ........................................77

Conexión de tubería de agua a manguera de válvula de cierre

del hogar ............................................. 78

Conecte la manguera de desagüe ...... 78

Complete la instalación ......................80

Verique el funcionamiento .................81

Instale los paneles de acceso .............81

Si la lavavajillas no funciona ............... 82

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using the dishwasher, follow basic precautions, including the following:

Read all instructions before using the dishwasher. Use the dishwasher only for its intended function. Use only detergents or rinse agents recommended for use in a

dishwasher, and keep them out of the reach of children. When loading items to be washed:

1) Locate sharp items so that they are not likely to damage the door seal; and

2) Load sharp knives with the handles up to reduce the risk of cut-type injuries.

Do not wash plastic items unless they are marked “dishwasher safe” or the equivalent. For plastic items not so marked, check the manufacturer's recommendations.

Do not touch the heating element during or immediately after use. Do not operate the dishwasher unless all enclosure panels are

properly in place. Do not leave the dishwasher open when not loading or unloading

dishes. Do not tamper with controls.

Do not abuse, sit on, or stand on the door, lid, or dish racks of the dishwasher.

Do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).

To reduce the risk of injury, do not allow children to play in or on the dishwasher.

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the dishwasher turn on all hot water faucets and let the water ﬂow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is ﬂammable, do not smoke or use an open ﬂame during this time.

Remove the door or lid to the washing compartment when removing an old dishwasher from service or discarding it.

This product is intended for residential use only. This product is not intended for use by persons (including

children) whose physical, sensory, or mental capacities are different or reduced, or who lack experience or knowledge, unless such persons are supervised or trained in the operation of the apparatus by a person responsible for your safety.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

■

For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The dishwasher is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

SAVE THESE INSTRUCTIONS

Check with a qualified electrician or service representative if you are in doubt whether the dishwasher is properly grounded. Do not modify the plug provided with the dishwasher; if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

■

For a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dishwasher.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

DISHWASHER MAINTENANCE

Detergents

High-quality premeasured tablets and packs are recommended for improved performance.

Quality tablets and packs have been proven better than powder, liquid, or gel detergents at reducing lming on dishes. Using tablets and packs over time will start to reduce or eliminate white lm. They are suitable for all water hardness and soil levels. Also, by using a rinse aid, you can minimize repeat buildup of white lm (not all packs and tablets contain rinse aid). Always place premeasured detergents in main compartment and close lid.

The Pre-Wash indicator on the dispenser lid is for customers who use powder or gel detergent and wish to add an amount of detergent to the Pre-Wash cycle. The volume of detergent added here is approximately 8 cubic centimeters, if lled full and level. Any detergent added here would be immediately added to the wash when the cycle starts versus detergent inside the dispenser which is added during the main wash cycle.

NOTE: Follow instructions on the package when using other dishwasher detergent types.

■ Use automatic dishwasher detergent only. Add detergent just

before starting a cycle.

■ Fresh automatic dishwasher detergent results in better

cleaning. Store tightly closed detergent container in a cool, dry place.

■ Extremely hard water mineral deposits (15 grains per U.S.

gallon or more) can cause damage to your dishwasher and make it difcult to achieve good results. A water softener is recommended to avoid damage and achieve good results.

■ For more details about powders, liquids, and gels and hard

water conditions consult the brand website.

Rinse aid

Using rinse aid will optimize your drying and wash performance. This dishwasher is specically designed to be used with rinse aid for improved drying performance and controlling buildup of hard water deposits. Rinse aid needs to be added to the product every 1 to 3 months depending on usage.

Refer to the Quick Start Guide or brand website for information about lling the rinse aid dispenser.

Cycle Selection and Energy

Efcient dishwashers run longer to save water and energy, just as driving a car slower saves on gas. Typical cycle time is approximately 2 1/2 hours, but can take less or signicantly more time depending on your selections and incoming water temperature and amount of food soils on the dishes. For optimum performance the dishwasher should be connected to a 120 F (49° C) hot water supply.

If you rst press the Start button, the main sensor cycle with heated drying will be automatically selected. This cycle senses the soil amount, and toughness of soil, to adjust the cycle for improved cleaning.

Sanitize or Sani

Sanitizes dishes and glassware in accordance with NSF International NSF/ANSI Standard 184 for Residential Dishwashers. Certied residential dishwashers are not intended for licensed food establishments. Only sanitizing cycles have been designed to meet the requirements of the NSF/ANSI 184 performance standard for soil removal and for sanitization efcacy. There is no intention, either directly or indirectly, that all cycles on a NSF/ANSI 184 certied dishwasher meet the NSF/ANSI 184 performance standard for soil removal and for sanitization efcacy. The Sani Rinse indicator glows at the end of the cycle if the Sani Rinse option was successfully completed. If the indicator does not activate, it is probably due to the cycle being interrupted.

DISHWASHER LOADING TIPS

NOTE: Features are model specic. Your dishwasher may not have all features described. See Quick Start Guides for possible

dishwasher loading patterns for all dish racks.

Silverware Baskets

Sliding Bowl Tines

Style 1

Style 3

Style 2

Use silverware basket lids to provide optimal spacing and best cleaning performance. NOTE: If your silverware does not t into the designated slots, open the lids (Style 1/3) or lift on the ends of the lids and pull to remove (Style 2). Mix silverware types to keep them separated. Load knives down, forks up, and alternate spoons for best cleaning results.

Removing Upper Racks

In order to make space for tall items, your upper racks are removable. The manner in which to remove will depend on whether the rack is mounted with Style 1 or Style 2. Remove dishes prior to removing any racks.

Style 1

To remove the rack, pull the rack forward about halfway out of the tub. On one side, press the tab on the track in and pull up the front end of the rack, out of the track. Then repeat this step on the other side to completely remove the front end of the rack. Then remove the rack by pulling the back end out using a forward and upward motion.

To replace the rack, Push back of rack into rail rst and then push front down.

The sliding bowl tines allow you to easily load bowls of multiple sizes. Grab the moveable tine row in the lower rack and slide into the desired position.

Fold Down Tines

Fold down tines allow you to optimize the spacing in the rack. Fold down tines might be in the lower rack , the second level rack and/or third level rack depending on your model. To fold or unfold the tine, hold the tine nearest the clip at the end of the tine row and gently push it past the stop on the clip and in the direction you want to fold it.

Stemware Holder

Use the stemware holders to support wine glasses and other stemware. Push them up to rotate them out of the way when not needed.

Stemware

Holder

Rack

Track Stop

Style 2

To remove the rack, pull the rack out until it stops. On the left and right side of the rack, push the plastic track stops on the front of the rail sideways to open them. Pull out the rack. To replace the rack, push the rack back onto the rails. Push the track stops closed.

Cup Shelf

Use the cup shelf to hold additional cups or small items. Push up to fold out of the way when not needed.

DISHWASHER CARE

Interior Cleaning

Many detergents may leave white spots or a white residue on dishware and on the interior of the dishwasher. Over time this residue can become unsightly and could affect dishwasher performance. Use of a dishwasher cleaning product such as affresh® Dishwasher Cleaner can help to remove the residue. Monthly use of affresh® Dishwasher Cleaner is recommended to help maintain the dishwasher. Follow package directions.

NOTE: We recommend the use of high-quality, premeasured detergent tablets or packs and the use of rinse aid for dishwasher cleaning and daily care.

Countertop Air Gap

If you have a drain air gap, check and clean it if the dishwasher isn't draining well.

Extended Time Without Use

To Reduce Risk of Property Damage During Vacation or Extended Time Without Use

■ When you will not be using the dishwasher during the summer

months, turn off the water and power supply to the dishwasher.

■ Make sure the water supply lines are protected against freezing

conditions. Ice formations in the supply lines can increase water pressure and cause damage to your dishwasher or home.

■ Damage from freezing is not covered by the warranty.

■ When storing your dishwasher in the winter, avoid water

damage by having your dishwasher winterized by authorized service personnel.

Exterior Cleaning

Clean the exterior of dishwasher with a soft, damp cloth and mild detergent. Avoid using abrasive cleaning products on the exterior of the dishwasher. Abrasive cleaning products can damage the nish.

Troubleshooting

The brand website listed on the Quick Start Guide has detailed information to troubleshoot most problems customers encounter. This information may save you the cost of a service call.

Foreign Object Cup

If the Foreign Object Cup is full the Quick Start Guide or the brand website listed on the Quick Start Guide has detailed information about how to empty it.

DISHWASHER SETTING MENU:

Follow the below instructions to enter into the menu to change your current settings.

Rinse Aid Level A X Adjust amount of rinse aid dispensed

Rinse Aid Level

sub-menu

Sound Level S X X Turn sound On and Off

Sound Level

sub-menul

Light in Tub L X Turn the inner light on and off (if present)

Lights in Tub

sub-menul

Kosher Consumer Friendly mode

Factory Reset r X X X Factory Reset

Display Text (if display is

present)

A 0 X X X 0 mL - rinse aid off A 1 X 1.3 mL A 2 X 2.6 mL A 3 X X 3.9 mL X A 4 X 5.2 mL A 5 X X 5.2 mL A 6 X X 5.2 mL

S 1 X Sound On X S 0 X Sound Off

L 1 X Light in Tub ON when door is opened X L 0 X Light in Tub OFF when door is opened

E X X

E 1 X Turn mode ON E 0 X Turn mode OFF X

PROWASH

LED Pattern (no display)

SENSOR

TOUGH OR

COOKWARE

NORMAL

What this setting does

Turn Kosher Consumer Friendly mode On and Off

Default Setting

1. Press and hold the “Hi Temp” button for 5 seconds until “Hi Temp” and “Dry” lights turn on.

2. Press the “Start/Resume” button within 2 seconds. If you do not press Start within 2 seconds, then the display will turn off and you

will need to start over and go back to step 1.

a. For Models with a Display, an “A” will show in the display to indicate Rinse Aid Level. b. For Non-display models,“Tough or Cookware” light will turn on to indicate Rinse Aid Level.

3. To go to a feature other than Rinse Aid Level, press the “Cycle” button or “Normal” button (depending on model) to move to the

feature you would like to change (Sound Level, Light in Tub, Kosher Friendly, Factory Reset, Rinse Aid Level). See the table for what is shown on the display to indicate these features.

4. Press the “Start/Resume” button to select the feature and enter the sub-menu. The display will change to show the current setting

of the feature. (For example, if you selected Sound Level and you haven’t changed it before, then S1 will show for display models and sensor will light for non-display models.)

5. Press “Cycle” button or “Normal” button (depending on model) to change the value of the feature setting. (For example, if you want

to turn the sound off, then press the “Cycle” or “Normal” button and S0 shows on display models or “pots and pans” lights for nondisplay models.)

6. Press the “Start/Resume” button to conrm the new selection. The feature setting will not be changed until the “Start/Resume”

button is pressed. The dishwasher will return to the Off state when the Start button is pressed.

To exit the customer settings menu at any time, press the “Cancel” button, or wait 30 seconds without pressing any buttons. NOTE: To see the current setting of a feature, follow steps 1-4. When the “Start/Resume” button is pressed in step 4, the dishwasher

will show the current setting. Press the “Cancel” button to exit without making any changes.

NOTE: If you enter into a Feature Setting Page and need to go back to the Main Menu Press “Cancel” and proceed to step 1. NOTE: To exit “Kosher Consumer Friendly Mode” at any time, press the “Cancel” button or you can wait 75 hours. Kosher Consumer Friendly Mode: When turned on, will disable all of the buttons on the dishwasher except for the cancel key, and

disable the light inside the tub (if equipped) for a time period of 75 hours. If this mode is turned on during a cycle, then the status lights at the end of cycle will not turn off when the door is opened and then re-closed. To exit this mode, press the “Cancel” button, or wait 75 hours.

ERROR CODES

ERROR CODES / BLINKING LIGHTS

Code Shown

Issue

Dishwasher fails to operate ll valve correctly

Motor controller failure

No water present at dishwasher

Wash motor failure F7E1/F7E2

Dishwasher overlls

Fill valve stuck on F8E5

Dishwasher will not drain

Water present under dishwasher

User interface service communication fault

(7 Seg Display)

(if present)

F1E1

F1E2

H2O

F8E4

F9E1

FAE5

F6E1

Code Shown on

Front Panel LED * (# blinks, Pause, #

blinks)

1 Pause 1 Pause -

pause, repeat

1 Pause 2 Pause,

repeat

8 Pause 1 Pause -

pause, repeat

7 Pause 1 Pause,

repeat/7 Pause 2

Pause, repeat

8 Pause 4 Pause -

pause, repeat

8 Pause 5 Pause -

pause, repeat

9 Pause 1 Pause -

pause, repeat

10 Pause 5 Pause -

pause, repeat

6 Pause 1 Pause -

pause, repeat

What will happen? What to do?

Drain sequence will begin, machine operation will be prevented

Cycle ends Call service

Cycle is paused

Cycle ends Call service

Drain sequence will begin, machine operation will be prevented

Cycle ends

Cycle ends Call service.

Product will not able to start or resume cycles

Turn off water to unit (if possible).Turn off power to unit. If the water cannot be turned off, DO NOT turn off power and keep door closed. Press Cancel key one time to silence alarm tone. Call service.

Ensure ll hose is connected to product. Ensure water supply is turned ON. Press Start to resume cycle. If alarm still present, call service.

For Professional Installers

Turn off water to unit (if possible). Turn off power to unit. If the water cannot be turned off, DO NOT turn off power and keep door closed. Press Cancel key one time to silence alarm tone. Call service.

For Self Installers

■ Press CANCEL button twice or cycle

power. This may clear the issue.

■ Check to see if the wire connector is

connected to the oat switch on the drip tray. See step 46. If the wire is off, reconnect and then hit the cancel button twice.

■ Check to see if there is any water in

the drip tray. If water is in the drip tray, remove the water and reinstall the drip tray. Make sure to connect the wiring to the oat. Step 46. Check to see where water may have leaked into the drip tray. (Check the water inlet ttings in steps 15 and 16 to see if they are leaking)

■ If water was in the tray and no leaks

were found, run the product on the shortest installation cycle while checking for leaks. The access panel should be off to observe any leaks.

■ If problem still exists, call for service.

If drain hose is connected to a garbage disposal, conrm that drain hose is not clogged and disposal plug has been knocked out. If unit still will not drain, call service.

Call service.

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with thetools listed here.

All Installations

Tools Needed:

Pliers Flat-blade screwdriver

Phillips screwdriver Utility knife

Other Useful Items You May Need:

Flashlight Shallow pan

Bath towel Masking, or duct tape

Parts Supplied:

Drain hose clamps (2) (1 large/red and 1 small/silver)

Drain hose

5/16" (7.9 mm) and 1/4" (6.4 mm) nut drivers or hex sockets

Measuring tape or ruler 5/8" (15.9 mm) open-end

10" adjustable wrench that opens to 11/8" (29 mm)

Small level

wrench

Torx† T20 and, if installing custom front panels, Torx T15 screwdrivers

#8 x 1/2" (12.7 mm) Phillips-head screws (2)

Make sure all parts are included in the literature package.

Door handle (on some models)

Undercounter mounting brackets (2)

†TORX, T15, and T20 are trademarks of Acument Intellectual Properties, LLC.

Other Parts Needed (not provided):

3/8" (9.5 mm) Compression x 3/4" (19 mm) Hose Fitting

with rubber seal and 90° elbow (required to properly connect household water line to the dishwasher.)

Part no: W10685193

Household Wiring (Metallic) Strain Relief to t 7/8"

(22 mm) hole (required to properly secure household wiring to the dishwasher terminal box.)

Part no: 4396672 NOTE: Use only UL Listed/

CSA Approved parts.

Optional Accessory Parts Available:

Moisture Barrier Tape NOTE: Moisture barrier tape

is an optional, added level of protection if installing a dishwasher under a wooden countertop. Recommended but not required for wooden countertop.

Part no: 4396277

Side Panel Kit

For enclosing the side of the dishwasher when installing it at the end of your cabinetry (Whirlpool part number varies with color).

First-Time Installations

Check local codes. Check existing electrical supply. See the “Electrical Requirements” section. It is recommended that electrical connections be made by a licensed electrical installer.

Additional Tools Needed:

Small tubing cutter Wire stripper

Cordless drill 1/2" (12.7 mm), 3/4" (19 mm),

and 11/2" (38 mm) hole saw bits

Additional Parts Needed (not provided):

Copper Tubing (3/8" O.D.

suggested) or Flexible Braided WaterSupply Line Kit. Kitincludes braided hose and 3/8" compression x 3/4"hosetting.

Part no: W10278635RP

Screw-Type Clamps 11/2"- 2"

(38 mm - 50 mm) (3maximum)

Call us at our toll-free number or visit the brand website listed in the Quick Start Guide for accessory and part information.

Optional-Longer Drain Hose (Maximum length 12 ft (3.7 m)

NOTE: Must meet AHAM/ IAPMO test standards, t 1" (25 mm) drain connection, and be resistant to heat and detergent.

Part no: W11381654

NOTE: If using a exible braided hose, replace inlet hose after

5years to reduce the risk of hose failure. Record hoseinstallation or replacement dates on the hose for futurereference.

NOTE: Be sure to purchase only Whirlpool factory-certied parts and accessories for your appliance. Your installation may require additional parts. To order, refer to the contact information referenced in your Quick Start Guide.

For Direct Wire For Power Cord

Cabinet G

For 11/2" (38 mm) hole in cabinet.

NOTE: Required for metal cabine

Call us at our toll-free number or visit the brand website listed in the Quick Start Guide for accessory and part information.

rommet

Power Cord Ki

Kit typically includes power cord, metallic strain relief,grommet.

(Whirlpool Part Number Cord Kit - Straight -

W11365011 Cord Kit - Right Angle -

W11365014)

LOCATION REQUIREMENTS

Dishwasher must be fully enclosed (top, sides, back, and oor) upon installation. A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.

An optional moisture barrier accessory is also available for installing underneath a wooden countertop.

Check location where dishwasher will be installed. The location must provide:

■ Convenient access for loading and unloading dishes. Corner

locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.

■ Easy access to water, electricity, and drain:

■ Grounded electrical supply is required.

■ This dishwasher has a water heating feature and also

requires a connection to a hot water supply line.

■ Make sure pipes, wires and drain hose are within the

shaded area shown in the “Product and Cabinet Opening Dimensions” section.

■ Do not run drain lines, water lines, or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

■ Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by the warranty.

NOTE: If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel.

■ If installed in new construction, ush the water supply line of

debris before connecting it to the ll valve. If it is not ushed, debris from the water supply could plug the ll valve screen.

■ A square opening for proper operation and appearance.

■ The cabinet front to be perpendicular to oor.

■ Level oor.

Helpful Tip: If oor at front of opening is not level with oor at rear of opening, shims may be used to level dishwasher.

NOTE: To avoid shifting during dishwasher operation, shims must be securely attached to the oor.

■ The location where the dishwasher will be installed must

provide clearance between motor and ooring. Motor should not touch the oor.

■ Do not install dishwasher over carpeted ooring.

PRODUCT AND CABINET OPENING DIMENSIONS:

237/8"

(60.4 cm)

24½"

(62.6 cm)

3/4"

(1.9 cm)

30"

(76.2 cm)

31/2" - 41/2"

(8.4 cm - 10.6 cm)

335/8"

(85.4 cm)

min. with legs

removed

30"

(76.2 cm)

3¾"

(9.7 cm)

2013/16"

(52.9 cm)

A. Insulation may be compressed (not used on all models). B. For panel-ready models, dishwasher depth is 24"

(61.0 cm), not including the 3/4" (1.9 cm) custom door panel.

C. Door handles may protrude forward of the face of the dishwasher, varies by model.

Check that all surfaces have no protrusions that would prohibit dishwasher installation.

335/8" min.

(85.4 cm) min.

(10.2 cm)

(7.6 cm)

21"

(53.4 cm)

24"

(62.0 cm)

D. Measured from the lowest point on the underside of the countertop. May be reduced to 335/8" min. (85.4 cm) min. by removing the feet and perforated area of insulation (blanket) on dishwasher.

E. Minimum, measured from narrowest point of opening.

NOTE: Shaded areas of cabinet walls show where utility connections may be installed.

6¼"

(15.9 cm)

(5.1 cm)

DRAIN REQUIREMENTS

■ A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/ IAPMO test standards, is resistant to heat and detergent, and ts the 1" (2.5 cm) drain connector of the dishwasher.

NOTE: Do not connect multiple drain hoses together.

■ Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the oor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter or be connected to an air gap.

■ Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (50.8 cm) above suboor or oor.

Use of air gap

Air gap

■ If required, the air gap should be installed in accordance with

the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

■ Use 1/2" (1.3 cm) minimum I.D. drain line ttings.

WATER SUPPLY REQUIREMENTS

■ This dishwasher has a water heating feature and also requires

a connection to a hot water supply line.

■ A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)

water pressure can be veried by a licensed plumber.

■ 120°F (49°C) water at dishwasher.

■ 3/8" (0.95 cm) O.D. copper tubing with compression tting or

exible braided water supply line. NOTE: 1/2" (1.3 cm) minimum plastic tubing is not

recommended.

■ A 90° elbow with 3/4" (0.95 cm) hose connection with rubber

washer.

■ Do not solder within 6" (15.2 cm) of the water inlet valve.

■ If installed in new construction, make sure the house water

supply lines have been ushed prior to connecting the dishwasher to remove any debris that may exist in the supply line.

NOTE: If replacing an existing dishwasher, it is recommended to install a new water line and drain hose (supplied) with the new dishwasher.

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471

You Must Have:

■ 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply

■ Copper wire only

■ A maximum of 2 eld wiring supply conductors (12 AWG

largest size) plus 1 grounding conductor are permitted in the terminal box.

We Recommend:

■ A time-delay fuse or circuit breaker.

Circuit Requirements:

■ The dishwasher may be installed on the same circuit as a

garbage disposal providing that the branch circuit cannot exceed rated circuit load and must comply with all governing codes and regulations such as but not limited to National Electrical Code, ANSI/NFPA 70 - latest edition.

■ No electrical connections other than the dishwasher power

and ground connections can be made inside of the dishwasher terminal box.

If connecting dishwasher with a power supply cord:

■ Use UL Listed power cord kit marked for use with

dishwasher.

■ Plug into a grounded 3 prong outlet. Outlet must

meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

■ Use exible, armored, or nonmetallic sheathed

copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.

■ Use a UL Listed/CSA Approved metallic

strain relief.

INSTALLATION INSTRUCTIONS

WARNING

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Drill a 1½" (3.8 cm) drain hose hole in the side or rear of cabinet, depending on location of drain hose routing and drain hose connection location.

Drill a 1/2" (1.27 cm) water supply hose hole in the side or rear of cabinet, depending on location of water supply routing and connection location

Drill a 1½" (3.8 cm) electrical conduit hole in the right-hand side or rear of cabinet.

1. Sand holes smooth

1. Video Installation

Video of installation steps can be found online at whirlpool. com in the “Service & Support” section “How To’s & FAQ.

The video can be found at

http://www.kaltura.com/tiny/ro00v

2. Disconnect power

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

3. Shut off water supply

Shut off the water supply to the dishwasher.

PREPARE CABINET OPENING— NEW UTILITIES

Metal

Wood

Cabinet

Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover edges of hole with grommet included with

power cord kit. Helpful Tip: Wiring the dishwasher will be easier if you route

the cable into the cabinet opening from the right-hand side.

Cabinet

INSTALL OPTIONAL MOISTURE BARRIER -

RECOMMENDED FOR WOOD COUNTERTOPS

Moisture barrier/wood shims

Moisture

barrier

4. Drill hole locations—new construction

Optional

location

1½"

(3.8 cm)

The power-supply receptacle for the appliance shall be installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance is to be installed.

NOTE: Refer to the “Product and Cabinet Opening Dimensions” section for the correct hole placement and dimensions of the shaded area.

Preferred

location

1/2"

(1.27 cm)

Install wood shims

Make sure the area under the cabinet is clean and dry for installation of the moisture barrier. Remove the backing of the moisture barrier, and apply to underside of the countertop along the front edge of the counter.

NOTE: The use of this moisture barrier is recommended but not required.

NOTE: Install wood shims if side anchoring and the gap between the sides of the cabinet and sides of the dishwasher are greater than 1/2" (1.27 cm) on each side or are greater than the length of the side anchor screws.

5. Built-up oors – add shims as needed

Shim

Note: The wood runners that come with the shipping base work well for shims.

Built-up oors: If the kitchen oor is higher than the cabinet opening’s oor - for example, the kitchen oor tile does not extend into the cabinet opening - add shims, as needed, in the area shown to bring cabinet oor up to same level as the kitchen oor.

NOTE: Shims must be securely attached to oor to avoid movement when the dishwasher is in use.

ELECTRICAL CONNECTION

– For Direct Wire, begin with Step 7 – For Power Cord, wait until Step 18

7. Direct wire – route cable

6”

(15.2 cm)

6. If installing into a 33

/8" (85.4 cm)

opening

Cut insulation blanket along perforation for cabinet opening height of 335/8" (85.4 cm). For other cabinet opening heights, do not cut the insulation blanket.

If installing with direct wire, route the cable as shown. Do not connect the wire to the product at this time. This connection will be made later, after the unit is installed into the cabinet opening.

Route cable from power supply through cabinet hole. (Cable must extend to the right front side of cabinet opening.) Tape cable to the oor in area shown. This will prohibit cable from moving when dishwasher is moved into cabinet opening.

PREPARE DISHWASHER

REMOVE ACCESS PANEL AND INSULATION

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

8. Put the dishwasher on its back

9. Remove access panels

Using a 5/16" (7.9 mm) nut driver, remove the two screws attaching access panels to dishwasher. Once the screws are removed push the access panel toward the top of the product to unhook it and then remove it.

DISCONNECT AND REMOVE DRIP TRAY ASSEMBLY

10a. Remove drip tray assembly

Helpful Tip: Remove all internal shipping material, drain hose,

installation kit, and handle (if included,) before laying on it’s back, and do not remove lm on the door at this time.

Place cardboard under dishwasher until installed in cabinet opening to avoid damaging oor covering.

Using two or more people, grasp sides of dishwasher door frame, and place the dishwasher on its back.

Do not use the door panel as a worktable without rst covering it with a towel to avoid scratching the door panel.

Drip tray assembly

To remove the drip tray assembly, press the snap at each side of the plastic tray in toward the center of the product and pull toward yourself. Be sure not to pull too far or too hard as the oat switch wire is still connected at this time.

10b. Remove oat switch wire

To remove the oat switch wire, gently push the connector latch tab (1) and then pull the connector (2) out of the housing. The oat itself should not be removed from the tray.

NOTE: Do not reinstall drip tray until instructed.

11. Measure cabinet opening

Measure the height of cabinet opening from the underside of the countertop to the oor where the dishwasher will be installed. Be sure to measure the lowest point on the underside of the countertop and the highest point on the oor.

Leveling leg adjustment

CONNECT WATER LINE TO FILL VALVE

– For Copper line, begin with Step 12 – For Flexible line, begin with Step 14

12. Copper Water Line

Use wrench to initially loosen leveling legs if needed. Adjust all four leveling legs to the same height by rotating each

foot clockwise or counterclockwise as needed. The unit comes with the legs set for a 335/8" (85.4 cm) height

installation. If your opening height is 34½" (87.6 cm), you would therefore need to raise all four legs by 7/8" (2.22 cm).

NOTE: Adjust rear leg height rst before moving unit into the cut out.

Legs can be removed if necessary for tight installations.

If using copper tubing, measure overall length of copper tubing required to reach the water supply, cut to length, and attach with compression ttings.

13. Slide nut and ferrule onto tubing

(copper tubing only)

Nut

Ferrule

Copper tubing only: Put the tubing into the 90° elbow tting as far as it will go. (The copper tubing bends and kinks easily.) Push the nut and ferrule forward and tighten it, so that it sits right up against elbow threads.

NOTE: To avoid vibration during operation, route the water supply line so that it does not touch the dishwasher base, frame, or motor. If using copper tubing, skip step 14 and go to 15.

Get 3/8" compression x 3/4" hose tting with 90° elbow. Connect the 3/8" compression tting of the 90° elbow tting to the water supply line. Attach such that the 3/4" connection is facing upward as shown below.

15. Add 90° elbow tting to the water

supply line

CONNECT FILL HOSE TO FILL VALVE

16. Tighten 90° elbow tting to valve

14. Flexible line

Flexible braided line: Conrm the exible braided line is long

enough.

Elbow tting

Be sure rubber washer is properly seated in tting. Slide the 3/4" (19 mm) tting of the 90° elbow up to the valve and hand tighten it to avoid cross-threading. Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An additional 1/4 to 1/2 turn may be required to seal the rubber gasket. Route ll hose out the rear left side of unit.

NOTES:

■ Do not use tape with compression ttings.

■ Do not over-tighten. Damage to the coupling can result.

■ Route water supply line out rear of unit before setting unit up.

DRAIN HOSE CONNECTION

17. Connect drain hose

Drain Hose Location

18. Remove terminal box

Terminal

box

To remove the terminal box, depress the plastic latch, slide the box toward the left of the unit along the metal tube and rotate the left side of the box forward. Make sure that the product wiring is still attached within the terminal box.

19. Remove terminal box cover

Terminal

box cover

Put provided silver clamp over elbow end of drain hose. Then push the hose onto the drain port (being sure to push all the way on) with the hose facing underneath the dishwasher. Using pliers, squeeze open the drain hose clamp and slide it over the elbow to ensure the hose is attached in place. Route the hose out of the back of the product.

NOTE:

■ If the hose is installed with the rubber elbow facing out, the

drain hose may become kinked causing slow or incomplete draining in tight cabinet installations.

■ There may be a plastic plug in the drain port for shipping

purposes where you will connect the drain hose. Remove this plug before installing drain hose, if present.

POWER CORD CONNECTION

NOTE: If installing a product with direct wiring, proceed to Step

25, wait to install wiring until after Step 44 when the unit has been installed in the cabinet opening.

Select UL Listed/CSA Approved power cord for the Dishwasher.

Power Cord Ki

Kit typically includes power cord, metallic strain relief,grommet. (Whirlpool Part Number Cord Kit - Straight - W11365011

Cord Kit - Right Angle - W11365014)

Using 1/4" (6.4 mm) nut driver remove the screw holding the terminal box cover. Remove the cover by lifting it out of the box. Keep the cover for later use.

20. Install strain relief

Install a UL Listed/CSA Approved metallic strain relief. Make sure screw heads are facing up when tightening conduit nut. Strain relief is provided with the power cord kit.

Suggested wire length relative to strain relief

41/2"

(114.3 mm)

0.75" - 1" (19 mm - 25 mm)

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

21. Connect ground wire

Ground connector

screw

Wiring conguration

23. Secure cord or wire in strain relief

Terminal

box cover

Ground

wire

Route power cord through strain relief in the back of the terminal box. Remove the ground connector screw on the raised oor inside the box and place it through the ring terminal of the green ground wire of power cord. If wire has no ring terminal, bend a loop in the end of the wire. Reattach and tighten the ground connector screw to the raised oor of the box.

Washer

Ground

screw

22. Connect remaining wires

White wire

Black wire

To connect wires with ring terminals, remove the screws from the terminal block, place the screw through the ring terminals, and reattach screws back into the terminal block.

To connect wires without ring terminals, remove the screws from the terminal block. Bend a loop in the end of the wires. Push the screws through the loop. Return the screws to the terminal block. Tighten the screws.

NOTE: Pre-tinned wires should not be used when connecting to the terminal block.

White wire

Ground wire

Black wire

Tighten strain relief screws to secure cord.

24. Reinstall terminal box cover and wires

Place wires inside terminal box. Replace the cover by inserting the hooks of the terminal cover into the slots in the oor of the terminal box and sliding the cover tight against the back wall where wires come in. Make sure wires are tucked inside the box and not pinched by the cover.

Put the terminal box back on the crossbar and push to the right so terminal box snaps into the plastic side member.

NOTES:

■ Do not plug cord into an outlet until instructed to do so.

■ Once the terminal box has been remounted on the dishwasher,

tuck any excess length or slack over nearby components to help keep them off the oor.

■ Route cord out the rear of the dishwasher so that it does not

touch dishwasher motor or lower part of dishwasher tub.

■ A maximum of 2 power cord supply conductors (12 AWG

largest size) plus 1 grounding conductor are permitted in the terminal box.

IMPORTANT: No additional connections other than dishwasher power connection are to be made inside the dishwasher terminal box.

INSTALL DOOR HANDLE

(ON SOME MODELS)

25. Install door handle

Mounting stud

Setscrew (in bottom of handle)

IMPORTANT: Do not scratch the front panel during this procedure. If door panel has a protective lm, peel lm back past the point of the handle studs before installing handle. Handle is easiest to install while unit is on its back.

Remove the door handle and hex key from the packaging. Setscrews are already installed in the handle. Place handle on mounting studs with the setscrews facing down. Push the door handle tightly against the door. Insert the short end of the hex key into the setscrews. Tighten the setscrews 1/4 turn past snug.

Retain hex key with Installation Instructions.

Handle

Hex key

Install Foam Side Shields (on some models)

Install the foam side shields on both the right and left sides of the dishwasher. There are three attachment points on each side.

■ Attachment 1: Locate the slit on the side shield and attach it

to the hook on the side of the dishwashwe. (See gure 1)

Figure: 1

■ Attachment 2: Use the other slit on the side shield and

attach it to the hook on the front of the dishwasher. (See gure 2)

Figure: 2

■ Attachment 3: Align the rectangular hole in the side shield

with the toe panel screw hole. Insert the Toe Panel Screw(see gure 3) and Loosely tighten it to hold it in place until the Toe Panel is installed.

PLACE DISHWASHER IN CABINET

WARNING

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

26. Stand dishwasher upright

Using two or more people, stand the dishwasher up. NOTE: Do not install kick plate until instructed to do so. Dishwasher may t tightly into cabinet opening. Do not remove

insulation blanket—the blanket reduces the sound level. IMPORTANT: Do not kink or pinch water line, drain hose, power

cord, or direct wire between dishwasher and cabinet. Remove cardboard from under dishwasher (if used).

Figure: 3

■ Tuck the lower ends of the side shields under the

dishwasher. (See fugures 4 and 5)

Figure: 4

Figure: 5

NOTE: Route water supply, drain hose, and power cord out the

rear of the dishwasher. If your product has insulation around the bottom, route these lines through the slits in that insulation in the rear of the product.

27. Move dishwasher close

to cabinet opening

Water line

Drain hose

Cable

Route the utilities through the holes in the cabinet, and pull the slack out at the same time as the dishwasher is pushed into the cabinet.

28. Route power cord

30. Move dishwasher all but 6" (15.2 cm)

into cabinet opening

(15.2 cm)

■ Place Top Foam Sound Insulation (on some models)

• Snug the top foam into the slot on the top collar of the

dishwasher as shown in the gure.

NOTE: Leave unit about 6" (15.2 cm) out from cabinet in order to install anchor brackets.

31. Pull slack from utilities

If using a power cord, make sure to route the end through hole in cutout before sliding dishwasher into the cabinet opening.

29. Secure insulation blanket

Insulation

blanket

Secure blanket

NOTE: Make sure insulation blanket is secured at both left and right rear corners before pushing into cabinet opening to keep the blanket from bunching up in a tight tting cabinet. The blanket can be secured by pulling the insulation down toward the bottom of the product and ensuring the hooks on the side members grab onto the slots in the insulation blanket.

NOTE: Pull slack out of utilities at the same time the dishwasher is pushed into the cabinet opening to avoid any kinks.

CUSTOM PANEL INSTALLATION

(CUSTOM PANEL MODELS ONLY)

For custom panel installation, refer to the Custom Panel Installation Instruction Sheet included in the literature package. Complete custom panel installation before proceeding to the “Choose Anchor Attachment Method” section.

CHOOSE ANCHOR ATTACHMENT METHOD

IMPORTANT: The dishwasher must be secured to the cabinet

as one of the nal steps. Prepare the dishwasher for this by attaching the 2 brackets found in the parts bag to the dishwasher.

– For countertops that are wood, laminate or another similar surface: use Countertop Attachment and go to Step 32.

– For countertops that are marble, granite, or another hard surface: use Side Attachment and go to Step 33.

NOTE: If the gap between the top of the door and the underside of the counter top is tight (less than 1/4" [6.35 mm]), we suggest using Side Attachment to keep from scratching the User Interface or console with the anchor screws.

Countertop Attachment:

32. Insert bracket

34. Install bracket for Side Attachment

Tabs must point to the right.

Remove the brackets from the package, and insert into the open slots on the left- and right-hand top of the dishwasher collar as shown.

32a.

Counter top attachment

Bend tabs

Push bracket into slot on the side of dishwasher, and bend tab in toward the side of the dishwasher so that it keeps the bracket in place. Repeat this step for the other side of the dishwasher.

NOTE: Install wood shims to the inside of the cabinets if the gap between the sides of the cabinet and the sides of the dishwasher are greater than 1/2" (1.3 cm) on each side.

NOTE: Do not attach the dishwasher. This will be done later.

FINAL INSTALLATION CHECK

35. Open and close door

Using pliers, bend/twist tab to lock the brackets in place.

Side Attachment:

33. Break end of bracket for side

attachment

Top score line for stainless steel tubs

Bottom score line for plastic tubs

Break off the end of the bracket along the scored line using pliers. Use sandpaper to smooth any burrs.

36. Align front of dishwasher with front of

cabinet doors

Align front of dishwasher door panel with front of cabinet doors. You may need to adjust alignment to be even with your cabinets.

37. Check for plumb and adjust legs if

needed

■ Check that leveling legs are rmly against the oor. Close and

latch the door and place level against the front panel. Check that dishwasher is centered from front to back in the opening. If needed, adjust leveling leg until dishwasher is plumb. Repeat for other side of dishwasher.

■ With dishwasher plum check that racks do not roll out on their

own when you open the door. Adjust front level legs until racks no longer roll unless you pull them.

Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs. With some installations, it may be easier to adjust the front leg using a 7 mm hex head socket or adjustable wrench. If the gap between the top of the door and the underside of the counter top is tight (less than 1/4" [6 mm]), we suggest side anchoring to keep from scratching the User Interface or console.

SECURE DISHWASHER IN CABINET OPENING

39. Double-check dishwasher alignment

in cabinet opening

Check that dishwasher is still level front to back and side-to-side in the cabinet opening.

Open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This will keep screws from falling into pump area when you are securing dishwasher to cabinet.

40. Secure dishwasher

Level front legs

Optional methodPreferred method

38. Check level side to side and adjust

legs if needed

Screw to side

cabinet

Open dishwasher door to prepare for securing the dishwasher to the countertop or side cabinet.

NOTES:

■ The dishwasher must be secured to keep it from shifting when

the door is opened or closed.

■ Do not drop screws into bottom of dishwasher.

■ Locate brackets installed in the “Choose Anchor Attachment

Method” section, either on top or on the sides of the dishwasher.

■ If countertop anchoring: Secure dishwasher to the countertop

with two Phillips-head screws (included).

■ If side anchoring: Drill 7/32" pilot holes in cabinet to avoid

splitting the wood. Secure dishwasher to cabinet with two Philips-head screws (included). Remove second rack for easier access. See the Dishwasher Loading Tips section for instructions on how to remove the second rack if needed.

Place level against top front opening of tub. Check that dishwasher is level from side to side. If dishwasher is not level, adjust front legs up or down until dishwasher is level.

41. Check door clearance

IMPORTANT: Check that top of door does not contact screws,

brackets, or countertop. If it does, adjust leveling legs or use the side attachment option.

CONNECT WATER LINE TO HOUSE SHUT-OFF VALVE

NOTE: If using a exible braided hose, replace inlet hose after 5

years to reduce the risk of hose failure. Record hose installation or replacement dates on the hose for future reference.

44. Attach water supply line

42. Check inner spacing

Open door and check that space between dishwasher cabinet opening and tub is equal on both sides. If spacing is not equal, loosen bracket screws and shift tub. Tighten bracket screws.

43. Direct Wire Connection

To complete direct wire connection. Complete Steps 18 to 24 in this installation guide.

Once complete, return here to Step 44 to complete Product Installation.

Attach the water supply line (copper tubing or exible braided line) to the hot water line using a connection conguration that is in compliance with local codes and ordinances. The water supply to the dishwasher should have a manual shut-off valve located under the sink. Turn water valve on after attaching water supply line.

CONNECT DRAIN HOSE

45. Connect drain hose

Connect drain hose to waste tee or waste disposer using one of the following options:

■ Option A: Waste disposer – no air gap

■ Option B: No waste disposer – no air gap

■ Option C: Waste disposer – with air gap

■ Option D: No waste disposer – with air gap

IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20" (50.8 cm) above the oor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away from the oor.

NOTE: Use the red clamp provided to connect the drain hose to

the customer connection - plumbing or garbage disposal.

Option A: Waste disposer—no air gap

Disposer inlet

Large drain hose clamp

Option B: No Waste disposer—no air gap

Waste tee

Large drain hose clamp

Drain trap

Helpful Tip: Remove disposer knockout plug.

1. Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Attach drain hose to disposer inlet with

large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position.

Drain hose

Drain trap

1. Fit rubber end of drain hose

Rubber end

towastetee.

2. Attach rubber end of drain hose to

waste tee with a large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position.

Option C: Waste disposer – with air gap

Screw-type clamps

Disposer inlet

Air gap

Large drain hose clamp

Rubber hose

connector

Drain hose

Drain trap

Helpful Tip: Remove disposer knockout plug.

1. Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Connect rubber end of drain hose

Rubber

end

toairgap.

4. Attach drain hose to air gap with large

drain hose clamp (provided). Use pliers to squeeze clamp open and move into position.

5. Use a rubber hose (not provided) with

screw-type clamps to connect from air gap to disposer inlet.

Option D: No waste disposer – withairgap

COMPLETE INSTALLATION

46. Reconnect oat switch

Rubber

end

Waste tee

Drain trap

Screw-type clamps

Air gap

Large drain

hose clamp

Rubber hose

connector

Drain hose

1. Connect rubber end of drain hose

toairgap.

2. Attach drain hose to air gap with large

drain hose clamp (provided). Use pliers to squeeze clamp open and move into position.

3. Use a rubber hose (not provided) with

screw-type clamps (not provided) to connect from waste tee to air gap.

Check that the power supply wire or cord does not touch dishwasher motor or the lower part of the dishwasher tub.

Reconnect oat switch by aligning connector removed in Step 10 with the connector housing and pushing in until the locking tab is visible over the back of the connector.

47. Replace drip tray

NOTE: Before replacing the dip tray, ensure that there is no water

present in the tray. To replace drip tray, align with snaps in side members and push

in toward unit. It is important that the black hoses are above the drip tray on both ends once it is pushed all of the way in.

+ 58 hidden pages