Jenn-Air JDB3200AWB4, JDB3200AWS4, JDB3200AWW4, JDB3600AWP4, JDB3600AWS4 Installation Guide
...
JENN-AiR°
LAVE-VAISSELLESOUS PLAN DE TRAVAIL
iNSTALLATiON iNSTRUCTiONS
UNDERCOUNTER DISHWASHER
iNSTRUCTiONS D'INSTALLATION
Table of Contents ................................... 2
Table des matieres .................................. 26
W10282554A
Table of Confenfs
Dishwasher Safety ................................. 2
Installation Requirements ........................... 3
Tools and Parts ................................... 3
Location Requirements ............................ 4
Drain Requirements ............................... 6
Water Supply Requirements ........................ 6
Electrical Requirements ............................ 6
Installa6on Instructions ............................. 7
Prepare Cabinet Opening--Existing Utilities ........... 7
Prepare Cabinet Opening--New Utilities .............. 7
Prepare and Route Water Line ...................... 8
install Drain Hose ................................ 9
install Moisture Barrier (under a wood countertop) .... 11
Prepare Dishwasher ............................. 11
Make Power Supply Cord Connection ............... 12
Installation instructions (cont.)
Determine Cabinet Opening ....................... 14
install the Door Handle (on some models) ........... 14
Install Custom Panel ............................. 15
Choose Attachment Option ........................ 16
Move Dishwasher into Cabinet Opening ............. 17
Connect to Water Supply ......................... 19
Connect to Drain ................................ 20
Make Direct Wire Electrical Connection .............. 20
Secure Dishwasher in Cabinet Opening ............. 21
Bottom Sound Pad installation (on some models) ..... 23
Complete Installation ............................. 23
Check Operation ................................. 24
If Dishwasher Does Not Operate ................... 24
Additional Tips .................................. 24
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
You Need to:
, Slowly open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.
, Observe all governing codes and ordinances.
, install this dishwasher as specified in these instructions.
, installation should be performed by a qualified service
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
technician. The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
2
iNSTALLATiON REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.
All Installations
Tools needed:
P ers Flat-blade
I screwdriver _
5 iJ 1 ii
_A6 and ¼ _./_3 UL Listed or CSA
nut drivers or _y Approved twist-on 0
hex sockets _ wire connectors*
10" adjustable wrench_ %" onen-end
that opens to /_ wrench ,._J'_f
11/8"(2.9 cm) _.
If installing custom front panels,
Torx ®_T15 screwdriver
-Must be the proper size to connect vour household wiring
to 16-gauge wiring in dishwasher
Other useful items you may need:
F ash ight ,,__ i Bath towel _.._
Other parts you may also need:
11/2'!_2'' Masking or Moisture
(3,81_510 Cm) duct tape barrier tape ._
screw_type i I (Part Number_ /
damps
NOTE: Moisture barrier tape is recommended when installing a
dishwasher under a wood countertop.
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a licensed electrical installer.
In addition, for first=time installations
Tools needed:
Cordless drill
With 1/2,:3/4;
and 11/2 hole
saw bits
Parts needed:
Copper tubing (%'i See "Electrical Requirements" section
O.D. suggested) or ....
flexible braided E°rDirect Wire: For P0werSupp]y
water su_] • li_e use UL Listed/ Cord: use UL
CSA Certified listed power
_/------_-, strain relief to I supply cord kit
1 ))I fitTA (2i2 I PartNUmbe[ 4317824
hole marked for use
' With dishWaSher
Parts supplied:
Drain hose
clamps (2)
(1 large and
1 small)
Drain hose
#10 x 1/2''
sPchillips-head
rews (2)
2 - under-
counter
mounting
brackets (top)
d
Silver Green
Make sure all these parts are included in the literature package.
Parts needed:
3 3 " "
3A C0mprx ¼ Hose F_ttmg
FOrpart o[ kit, see local
retai!er or Call Whirlpoo!
Parts: t_800-442_9991. Part
4 #10 x 1/2"wood screws (if installing custom front panels)
Additional parts supplied with top-venting models only:
8 l 0w
Additional parts supplied with certain models only:
Bottom sound pad q
(located in lower rack) J
Make sure all these parts are included in the literature package.
If parts are not included, call 1-800-688-1100.
t® TORX is a registered trademark of Acument Intellectual Properties, LLC.
3
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is
available from your dealer for installing underneath the
countertop. Call 1=800=688=1100 to order.
Check location where dishwasher will be installed. The
location must provide:
easy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
square opening for proper operation and appearance.
cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the
dishwasher opening is uneven (example: Flooring
extends only partway into opening).
NOTE: To avoid shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.
4
Product and Cabinet Opening Dimensions
*Insulation may be compressed
(not used on all models)
NOTE: Shaded areas of cabinet walls show where
utility connections may be installed.
*Measured from the lowest point on the
underside of countertop. May be reduced to
337/8" (86 cm) by removing wheels from
dishwasher.
**Minimum, measured from narrowest point of
opening.
Check that all surfaces have no protrusions
that would prohibit dishwasher installation.
/
Drain Requirements
Eiecfrical Requiremenfs
. A new drain hose is supplied with your dishwasher.
If drain hose is not long enough, use a new drain hose
with a maximum length of 12' (3.7 m) (Part Number
3385556) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the
1" (2.5 cm) drain connector of the dishwasher.
Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20"
(50.8 cm) minimum above the floor. It is recommended
that the drain hose either be looped up and securely
fastened to the underside of the counter, or be connected
to an air gap.
Be sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical
Code, ANSl/NFPA 70 - latest edition and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
You must have:
120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical
supply.
copper wire only.
We recommend:
a time-delay fuse or circuit breaker.
a separate circuit.
if connecting dishwasher
with a power supply cord:
Use UL listed power supply cord kit (Part Number
4317824) marked for use with dishwasher.
Power supply cord must plug into
a grounded 3 prong outlet, located in
the cabinet next to the dishwasher
opening. Outlet must meet all local
codes and ordinances.
Make sure to use an air gap if the drain hose is connected
to house plumbing lower than 20" (50.8 cm) above
subfloor or floor.
Use 1/2"minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap a rubber hose (not provided) will
be needed to connect to the waste tee or disposer inlet.
Water Supply Requiremenfs
* A hot water line with 20-120 psi (138-862 kPa) water
pressure can be verified by a licensed plumber.
* 120°F (49°C) water at dishwasher.
* 3/8"O.D. copper tubing with compression fitting or
flexible braided water supply line (Part Number
4396897RP)
NOTE:1/2"minimum plastic tubing is not recommended.
* A 90° elbow with 3/4"Hose connection with rubber
washer
* Do not solder within 6" (15.2 cm) of the water inlet valve.
if connecting dishwasher with direct wiring:
* Use flexible, armored
or nonmetallic
sheathed, copper wire
with grounding wire
that meets the wiring requirements for your home and
local codes and ordinances.
* Use a UL Listed!CSA Approved strain relief.
iNSTALLATiON iNSTRUCTiONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
Prepare Cabinet OpeningmExisting
Utilities
I Dis_e box or circuk I
_al!ing dishwasher.
YeS'FollOw instructi0ns in the "PrePare cab!net
Opening_Existing Utilities!! section_
NO_FollowinstructionS n the-prepare Cabinet
Opening_New Uti!ities sectionl
_: E :isting hookups g t ity hookups
Water line
If the water line and the cable extend to the locations
shown, proceed to the "Install Drain Hose" section. If they
do not reach far enough, follow the instructions in the
"Prepare Cabinet Opening--New Utilities" section.
Prepare Cabinet OpeningmNew
Utilities
Prepare and route the electrical supply
i i i_i
Option A, Power Supply Cord:
NOTE: A grounded 3 prong outlet is required inside a
cabinet next to the dishwasher cabinet opening.
Drill a 11/2"(3.8 cm) hole in cabinet side or rear.
See product and cabinet opening dimensions.
7
Woodcabinet:Sandtheholeuntilsmooth.
Metalcabinet:Coverholewithgrommetincludedwith
powersupplycordkit.
OptionB, Direct Wire:
Helpful "lip: Wiring the dishwasher will be easier if you
route the cable into the cabinet opening from the right-hand
side.
Route cable from power supply through cabinet hole (cable
must extend to the right front side of cabinet opening).
Tape cable to the floor in area shown. This will prohibit
cable from moving when dishwasher is moved into
cabinet opening.
Prepare and Route Wafer Line
Helpful Tip: Routing the water line through the left side
of cabinet opening will make water connection easier.
l_!JDirect Wire -- Drill hc
Optional location
Drill a %" (1.9 cm) hole in right-hand cabinet side or rear.
See product and cabinet opening dimensions.
Drill hole
Preferred locations
Drill a V2" (1.3 cm) hole in the cabinet side or rear.
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet (Part Number
302797 - not provided).
8
Measure overall length of copper tubing or flexible
braided water supply line. Attach to the hot water line
using a connection configuration that is in compliance
with local codes and ordinances. The water line to the
dishwasher should have a manual shutoff valve.
-:J water supply line
Slowlyroutewatersupplylinethroughholeincabinet.
(Ifusingcoppertubing,itwill bendandkinkeasily,sobe
gentle.)Itshouldbefarenoughintothecabinetopening
toconnectittothedishwasherinletonthefrontleft
sideofthedishwasher.
Slowlyturnwatershutoffvalveto "ON"position.Flush
waterintoashallowpanuntilcleartogetridofparticles
thatcouldclogtheinletvalve.Turnshutoffvalveto
"OFF"position.
Connect the 3/8"compression fitting to the water supply
line prior to installing the unit into the cabinet opening.
Attach such that the 3/4"connection is facing upward.
Copper tubing only: Put the tubing into the 90 ° elbow
fitting as far as it will go (the copper tubing bends and
kinks easily). Slide the nut and ferrule forward and start
the nut onto the elbow threads.
Flexible braided connection: Secure nut to elbow using
%" open ended wrench or adjustable wrench.
NOTE: Do not use Teflon ®* tape with compression
fitti ngs.
Install Drain Hose
iMPORTANT: Always use a new drain hose. Check local
codes to determine if an air gap is required.
Coppertubingonly:Slidenut,thenferrule,about1"
(2.5cm)ontocoppertubing.
NOTE:Toavoidvibrationduringoperation,routethe
watersupplylinesothatitdoesnottouchthe
dishwasherbase,frameormotor.
t® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
If needed, drill a 11/2" (3.8 cm) diameter hole in cabinet wall
or side of the opening closest to the sink.
Route drain hose as shown through hole in cabinet to the
front center of opening where drain connection will be
made. Tape drain hose to the floor in area shown. This will
prohibit it from moving when dishwasher is moved into
cabinet opening. 9
Connectdrainhosetowasteteeorwastedisposer
usingoneofthefolowingoptions:
•OptionA,Wastedisposer- noairgap
•OptionB,Nowastedisposer-noairgap
-OptionC,Wastedisposer-withairgap
-OptionD,Nowastedisposer-withairgap
IMPORTANT: The drain hose connection of the disposer or
a waste tee must be made before the drain trap and at
least 20" (50.8 cm) above the floor where the dishwasher
wil be installed.
Helpful Tip: To reduce vibration of the hose, keep the hose
away from the floor.
Option A, Waste disposer - no air gap
Option B, No waste disposer - no air gap
1. Connect black end of of drain hose to
waste tee and cut if needed.
(Do not cut ribbed section.)
2. Attach black end of drain hose to waste
tee with a large silver drain hose clamp
(provided). Use pliers to squeeze clamp
open and move into position. If the drain
hose was cut, use a 1W' to 2" (3.8 to
5 cm) screw-type clamp (not provided).
Option C, Waste disposer - with air gap
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle-nose pliers to remove
plug.
3. Attach drain hose to disposer inlet
with large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
Drain trap
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle-nose pliers to remove
plug.
3. Connect black end of drain hose to air
gap and cut if needed. (Do not cut
ribbed section.)
4,
Attach drain hose to air gap with large
silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 11/2'' to 2" (3.8 to
5 cm) screw-type clamp (not
provided).
10
5,
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.
Option D, No waste disposer - with air gap
....... Drab
Connect black end of drain hose to air
1.
gap and cut if needed. (Do not cut
ribbed section.)
2.
Attach drain hose to air gap with large
silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 11_"to 2"(3.8 to 5 cm)
screw-type clamp (not provided).
3.
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.
7;iiii_;iiii_;iiii_i_i_i;ii_:ii_7i_:ii_7i_:ii_7i_7_i:i7_7_i_i_i_`_i_i_i_`_i_i_7ii_i_i:ii_7i_:ii_7i_:ii_i1i_i1i_7i_i1i1_i_i_¸i,,,,;'ii,i;'ii,;,;,;,il_i;_;i_;i,i;'iii_;i_;_i;'iii_;i_;_i;'iii_;i_;_i;'iii_;i_;_i;'iii_;i_;_i;'ii,;,i;'ii,;,i;'ii,;,i;'ii'iii';'ii'iii'ii,;,;,i;'iii_;i_;_i;`_;_;_;_;_;_;_;_;_:_;_;_:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;::_
Prepare Dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Insfall Moisfure Barrier
(undera wood counterfop)
Install moisture barrier
(under a wood countertop)
Moisture
barrier
1. Make sure the area under the cabinet is clean and dry
for installation of the moisture barrier.
2. Remove the backing of the moisture barrier and apply
to underside of the countertop along the front edge of
the counter.
Helpful Tip: Place cardboard under dishwasher until installed
in cabinet opening to avoid damaging floor covering. Do not
use door panel as a work table without first covering with a
towel to avoid scratching the door panel.
Using two or more people, grasp sides of dishwasher door
frame and place dishwasher on its back.
Using a V4" hex head socket, nut driver or Phillips
screwdriver, remove two screws attaching access panel
and lower panel to dishwasher. Do not remove tech
sheet from access panel.
11
Using a 1/4" hex head socket, nut driver or Phillips
screwdriver, remove terminal box cover. Retain for
later use.
Make Power Supply Cord Connection
Option A, Power Supply Cord:
Route cord so that it does not touch dishwasher motor
to lower part of dishwasher tub. Pull cord through strain
relief in terminal bow. Take notice when installing or
removing the dishwasher in order to reduce the chance
of damaging the power supply cord.
Select UL Listed/CSA Certified twist-on wire connectors
(included with power supply cord kit) rated to connect
your power supply cord to 16-gauge dishwasher wiring.
Install a UL Listed/CSA Certified strain relief. Make sure
screwheads are facing to the left when tightening conduit
nut. Strain relief is provided with the power supply cord kit.
connection will you use? I
12
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Power Supply Cord--
Connect ground wire
-
0
II --G
wh te _white
ground wire_ ground connector
If needed, see website for animated representation of
this step. Visit www.jenn-air.eom under FAQ tab.
\
Remove the green grounding screw and place through
the ring terminal of the green ground wire. Reattach and
tighten the green screw.
NOTE: Twist on wire connector. Gently tug on wires to
be sure both are secured.
Connect wires black to black and white to white, using
UL Listed!CSA Certified twist-on wire connectors
(included with power supply cord kit).
Tighten strain relief screws to secure cord.
Place wires inside terminal box. Insert tabs on left side
of cover. Make sure wires are tucked inside box. Close
cover ensuring wires are not pinched. Use 1/4"nut driver
and previously removed screw to secure cover.
NOTE: Do not plug into outlet until instructed to do so.
13
iiiiiiiiiiiiiii_iiiiii_iiiiiiil¸il¸i_iYii_iiii_iii_iiiiiii1itii1iiii_i_i_ii_i_ii_i_ii_i_ii_i_i_i_i_i_ii_ii_i_ii_i_i_I_ii_ii_I_i_i_}1iiiiiiii_i_ii_i_i11iii!!iiiiiiii1i11ii1i1ii1i1%i1iiii%1i11tiiiii_i1iiiiiiii_i_¸il¸ii'iii_ii_i_ii'ii_ii_}iiiiiiiiil¸il¸ii_ii_ii_i_iiiiiiiiiiiiii_iii:`i_`_ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii1i111iiiiii11iiiii1tiii_iiiii1_i1iii_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiiiiiiiiiiiii_i_i_iiiiiii
Determine Cabinet Opening
Measure height of cabinet opening from underside of
countertop to floor where dishwasher will be installed
(you will need to measure the lowest point on the
underside of the countertop and the highest point on the
floor). Refer to "Dishwasher Height Adjustment Chart"
for wheel position and the number of turns needed.
| I
CaM net, Whee! Numbe[ 0t: turns
opening height poSition on front leg
7 remO_e AI! the way up33% (86.0 cm)
34"/S614Cm)1 10
NOTE: If the minimum cabinet opemng height is less than
34" (86.4 cm), the rear wheels can be removed for
additional clearance. This will allow the dishwasher to fit
into a 337/8.' (86 cm) high cabinet opening, but the
dishwasher will be more difficult to move. (Measurements
are approximate. Wheels and legs are preset at the
factory for 341/2.' [87.6 cm].)
Built-up floors (Kitchen floor height is higher than
cabinet opening.) Example: Kitchen floor tile does not
extend into cabinet opening. Add shims as needed in the
area shown to bring the dishwasher up to 34" (86.4 cm)
below the countertop.
NOTE: Shims must be securely attached to floor to avoid
movement when the dishwasher is in use.
Install the Door Handle
(on some models)
J
wheel
Turn both leveler legs to the same height. Put wheels in
the required position determined from "Dishwasher
Height Adjustment Chart."
14
)
IMPORTANT:Donotscratchthefrontpanelduringthis
procedure.
Removethedoorhandleandhardwarebagcontaining
thesetscrewsandAllenwrenchfromthecardboardbox.
Setscrewsarealreadyinstalledinthehandle.Place
handleonmountingstudswiththesetscrewsfacing
down.Pushthedoorhandletightlyagainstthedoor.
InserttheshortendoftheAllenwrenchintothe
setscrews.Tightenthesetscrews1/4turnpastsnug.
RetainAllenwrenchwithInstallationInstructions.
Custom panel dimensions--
Dishwashers with control panel
on the top
.....i
Install Custom Panel
(Model JDB3600AWX)
NOTE: The handle for the custom panel is not included.
IMPORTANT: If the handle is attached from the back of
the custom panel, the screw holes should be countersunk
for the screws heads to be flush with the panel. If the
handle is attached to the front of the custom panel, the
screw lengths cannot exceed the panel thickness. For
more information on Jenn-Air ®custom handle selection,
refer to the Jenn-Air ®Catalog, visit www.jenn-air.com, or
call 1-800-688-1100.
NOTE: A customer-supplied full front panel must weigh
no more than 16 Ibs (7.3 kg) and must be made to
specific dimensions. It is recommended that a
cabinetmaker cut the custom panel because of the
precise dimensions needed.
NOTE: All mounting hardware supplied is for a 3/4"
(19.1 mm) thick wood panel. If a thinner wood panel, or
materials other than wood are used, it is the customer's
responsibility to obtain the proper length screws and
adjust the pilot holes accordingly.
IMPORTANT: Use a moisture-resistant sealer on both
sides and all edges of the panel to avoid damage from
humidity.
3 screws
per side
outer [
Gently set outer panel aside. Lay the customer-supplied
custom panel face down on a covered, non-scratching
surface.
929/32 H
(25.2 cm)
p edge
Measure 92%2"(25.2 cm) from top edge and mark a line on
the back of customer-supplied custom panel. Position the
outer panel on the back of the customer-supplied custom
panel as shown, so that the top holes in the outer panel are
on the line, and both panels are centered side to side.
-:JDish . ash.erswith control !
panel on the top ......
231/2" __3
(59.7 cm) oaA_'' (76.7 cm)
(19.1 mm)
*This dimension is for 4" (10.2 cm) toe kick. If the
installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6" (15.2 cm).
With a TORX screwdriver, remove three screws from both
sides, as shown; hold the outer panel up while removing
the screws. Save screws for reinstallation.
®
Mark pilot
holes
Mark all four hole locations; remove outer panel. Drill %2"
pilot holes 1/2"(13 mm) deep in customer-supplied custom
panel. Place the outer panel on the back of the customer-
supplied custom panel; align holes.
15
_;51_ _¸¸¸ _
Customer-supplied
panel
edges
)rill through
these holes
top
Attach outer panel to back of customer-supplied custom
panel with the four #10-16 x %" hex head screws supplied
in the literature package. Attach the handle. The handle
should be centered on the front of the customer-supplied
custom panel in the area shown.
iMPORTANT: Screw heads must be flush with back of
customer-supplied custom panel.
R edges
3 screws
each side Customer-supplied
panel
Attach the panel assembly to the door by reinstalling the
three screws on each side; do not tighten completely. This
reinstallation of the three screws will hold the panel
assembly in place on the door frame,
Install the two #8-18 x 1%" screws from
the literature package in the top corners of the inner
panel. Tighten the six side screws reinstalled in Step 6.
Choose Affechmenf Opfion
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using 2 or more people, stand the dishwasher up.
Option 1, Countertop attachment:
11_,Remove bracket
Tabs must point
_s I ,%_ to the right
() :
top
edges
Drill through
these holes
Customer-supplied
panel
Align the top edge of the customer-supplied custom
panel with the top of the console.
Drill two %2" pilot holes 1/2"(13 mm) deep, into the
customer-supplied custom panel, through the holes in the
top corners on the inner panel, as shown.
16
Remove the brackets from the package and place in the
open slots on the left and right-hand top of the
dishwasher collar as shown.
Insert the bracket into the slot on the collar. Using a pair
of pliers, bend the tab down to secure the bracket in
place. Repeat this step for the other side.
NOTE: Do not attach the dishwasher. This will be done
later.
Loading...