JENN-AIR JCB2587WEY, JCB2587WEF Installation Instructions

INSTALLATION INSTRUCTIONS

Counter Depth Side by Side Refrigerator

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

INSTRUCCIONES DE INSTALACIÓN

Refrigerador de dos puertas con profundidad de mostrador

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

INSTRUCTIONS D’INSTALLATION

Réfrigérateur côte à côte à profondeur de comptoir

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents / Índice / Table des matières

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY............................... 2

INSTALLATION REQUIREMENTS ................. 2

Tools and Parts ............................................. 2

Product Dimensions...................................... 3

Location Requirements................................. 4

Electrical Requirements ................................ 4

Water Supply Requirements......................... 5

INSTALLATION INSTRUCTIONS ................... 5

Unpack the Refrigerator................................ 5

Install New Water Line .................................. 6

Connect Water Supply.................................. 6

Plug in Refrigerator ....................................... 7

Prepare the Water System............................ 7

Level Refrigerator.......................................... 8

Door Height Adjustment ............................... 8

Complete Installation .................................... 8

AYUDA O SERVICIO TÉCNICO...................... 9

SEGURIDAD DEL REFRIGERADOR .............. 9

REQUISITOS DE INSTALACIÓN .................... 9

Piezas y herramientas................................... 9

Medidas del producto................................. 10

Requisitos de ubicación.............................. 12

Requisitos eléctricos................................... 12

Requisitos del suministro de agua.............. 12

INSTRUCCIONES DE INSTALACIÓN .......... 13

Desempaque el refrigerador ....................... 13

Cómo instalar una tubería de agua nueva.. 13

Conexión del suministro de agua ............... 14

Cómo enchufar el refrigerador.................... 15

Preparación del sistema de agua ............... 15

Cómo nivelar el refrigerador ....................... 15

Cómo ajustar la altura de la puerta............. 16

Complete la instalación............................... 16

ASSISTANCE OU SERVICE .......................... 17

SÉCURITÉ DU RÉFRIGÉRATEUR................ 17

EXIGENCES D’INSTALLATION .................... 17

Outillage et pièces....................................... 17

Dimensions du produit................................ 18

Exigences d'emplacement ......................... 20

Spécifications électriques........................... 20

Spécifications de l’alimentation en eau ...... 20

INSTRUCTIONS D’INSTALLATION.............. 21

Déballage du réfrigérateur .......................... 21

Installation d’une nouvelle

canalisation d’eau ....................................... 21

Raccordement à la canalisation d'eau ....... 22

Brancher le réfrigérateur ............................. 23

Préparer le système d'eau.......................... 23

Nivellement du réfrigérateur........................ 23

Ajustement de la hauteur des portes.......... 24

Achever l’installation ................................... 24

Assistance or Service

If You Have Questions

If you have questions about operating, cleaning or maintaining your refrigerator, see the Use & Care Guide.

If You Need Service

Maintain the quality built into your refrigerator by calling an authorized service company.

To locate an authorized service company, see the Use & Care Guide for the number to call, phone the dealer from whom you purchased the refrigerator, or check the yellow pages of your local phone directory.

Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service.

W10272992A

Write down the following information about your appliance to help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label, located on the inside wall of the refrigerator compartment.

Dealer name____________________________________________________ Serial number __________________________________________________ Address ________________________________________________________ Phone number __________________________________________________ Model number __________________________________________________ Purchase date __________________________________________________

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Observe all governing codes and ordinances.

■ Installer: Leave Installation Instructions with homeowner.

■ Homeowner: Keep Installation Instructions for future reference

and for the local electrical inspector’s use.

■ Keep cardboard shipping piece or plywood under refrigerator

until it is installed in the operating position.

■ Comply with installation specifications and dimensions.

■ Remove any moldings or decorative panels from kitchen

cabinets that would not allow access to the refrigerator for service.

■ Contact a qualified electrical installer.

TOOLS NEEDED (on some models):

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Cordless drill

■ ¹⁄₄" Nut driver

and drill bit

■ Flat-blade

screwdriver

PARTS NEEDED (on some models):

■ Your refrigerator dealer has a kit available with a ¹⁄₄" (6.35 mm)

saddle-type shutoff valve, a union, and copper tubing.

■ Or you can purchase a ¹⁄₄" (6.35 mm) copper tubing with

shutoff valve and a ¹⁄₄" (6.35 mm) compression fitting (coupling).

■ Depending on water line connections, you may also need a ¹⁄₄"

(6.35 mm) nut and ¹⁄₄" (6.35 mm) ferrule.

■ ⁵⁄₁₆" or adjustable wrench

■ ⁷⁄₁₆" and ¹⁄₂" Open-end wrenches

■ Two adjustable wrenches

■ ³⁄₈" and ¹⁄₂" Socket wrenches

Top Vi ew

Product Dimensions

When leveling legs are fully extended to 1" (25 mm) below the refrigerator, add ³⁄₄" (19 mm) to the height dimensions.

³⁄₈"

35⁵⁄₈"

(90.5 cm)

15⁵⁄₈"

(39.6 cm)

A. Dimensions may vary based on the model

19¹⁄₂"

(49.5 cm)

(9.53 mm)

(61.0 cm)

(6.7 cm) max.

24"

(69.7 cm)

⁵⁄₈"

27¹⁄₂"

(76.4 cm) max.

30¹⁄₈"

Side View

■ Height dimensions are shown with the leveling legs extended

to the minimum height of ¹⁄₄" (6.35 mm) below the refrigerator.

■ The power cord is 66" (167.7 cm) long.

■ The water line attached to the back of the refrigerator is 78"

(198.1 cm) long.

21¹⁄₄"

(54.1 cm)

Front View

35¹¹⁄₁₆"

(90.6 cm)

Model Size Height A

23' (654 L) 25' (694 L)

64⁷⁄₈" (164.8 cm) 67³⁄₄" (172.1 cm)

3⁵⁄₈"

(9.2 cm)

66"

(167.7 cm)

3⁵⁄₈" (9.2 cm)

Model Size A B C

23'

(654 L)

25'

(694 L)

68³⁄₄"

(174.6 cm)

71³⁄₄"

(182.2 cm)

68⁷⁄₈"

(175.0 cm)

71⁷⁄₈"

(182.5 cm)

68¹⁄₂"

(174.0 cm)

71¹⁄₂"

(181.6 cm)

Opening Dimensions

)

■ Height dimensions are shown with the leveling legs extended

to the minimum height of ¹⁄₄" (6.35 mm) below the refrigerator. NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add ³⁄₄" (19 mm) to the height dimensions.

■ Minimum fixed wall position is 13¹⁄₄" (34 cm) from the freezer

door and 16¹⁄₂" (42 cm) from the refrigerator door.

36"

(91.5 cm)

¹⁄₂"

¹⁄₄"

(34 cm)

(42 cm)

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

NOTES:

■ The cabinet depth refrigerator can be installed into a recessed

opening, at the end of cabinets or as a freestanding refrigerator.

■ If you are installing the refrigerator to fit flush with the front of

the base cabinets, all shoe molding and baseboards must be removed from the rear of the refrigerator opening.

■ For full-overlay cabinet doors, the height of the opening must

be 69¹⁄₈" (175.6 cm).

■ Location should permit doors to open fully. See the “Door

Swing Dimensions” section.

■ Do not install the refrigerator near an oven, radiator, or other

heat source, nor in a location where the temperature will fall below 55°F (13°C).

■ Floor must support refrigerator weight (more than 600 lbs

[272 kg], door panels and contents).

Model Size Height A

Standard Cabinet

23' (654 L) 25' (694 L)

69" (175.3 cm) 72" (182.9 cm)

Height A

Full-overlay*

69¹⁄₈" (175.6 cm) 72¹⁄₈" (183.2 cm)

*For full-overlay cabinet doors with a trim kit, the opening height

must be adjusted as shown.

Door Swing Dimensions

Location must permit doors to open to a minimum of 150°. Allow 13¹⁄₄" (34 cm) minimum space between the side wall and the freezer side of the refrigerator. Allow 16¹⁄₂" (42 cm) minimum space between the side wall and the refrigerator side.

NOTE: Dimensions may vary based on model.

³⁄₄"

(106 cm)

13⁵⁄₈"

(34.5 cm)

⁵⁄₈"

(6.6 cm)

¹⁄₂"

(12.7 mm)

90˚

150˚

17"

(43.0 cm)

0" (0.1 mm)

45¹⁄₂"

(115.6 cm

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or two

adjustable wrenches

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain above freezing.

■ ¹⁄₄" Nut driver

■ ¹⁄₄" Drill bit

■ Cordless drill

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

WARNING

Broken Glass Hazard Do not hit refrigerator glass doors. Protect glass surface and edges during installation or

removal of doors. Failure to do so can result in serious eye injury or

minor cuts.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System” in the Use & Care Guide.

If you have questions about your water pressure, call a licensed, qualified plumber.

Remove the Packaging

Dispose of/recycle all packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

IMPORTANT:

■ Use ³⁄₈" socket wrench to remove skids.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the Use & Care Guide.

Important information to know about glass shelves, covers and door panels (on some models):

• Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

• Do not hit the glass door panels with pots, pans, furniture, toys or other objects. Scratching, hitting, jarring or stressing the glass may weaken its structure, causing an increased likelihood of breakage at a later date.

• For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal.

Install New Water Line

(if required)

TOOLS NEEDED:

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or

two adjustable wrenches

1. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

2. Find a

¹⁄₂" (12.70 mm) to 1¹⁄₄" (3.18 cm) vertical COLD water

pipe near the refrigerator. NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

3. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

4. Using a cordless drill, drill a

¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

■ ¹⁄₄" Drill bit

■ Cordless drill

A B

5. Fasten shutoff valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the

¹⁄₄" (6.35 mm) drilled hole in the

water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.

6. Slip compression sleeve and compression nut on copper

tubing as shown in the diagram. Insert the end of the tubing into the outlet end of the shutoff valve as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.

7. Place the free end of the tubing into a container or sink, turn

ON main water supply and flush out tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

Connect Water Supply

Style 1 - Connection to Water Valve

1. Unplug refrigerator or disconnect power.

2. Before attaching copper tubing to refrigerator, flush at least

2 qt (1.9 L) of water through the copper tubing and into a bucket to get rid of any particles in the water line.

3. Check for leaks around the saddle valve. Do not overtighten

clamp or sleeve. This will crush copper tubing.

4. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

5. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

6. Turn shutoff valve ON.

7. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A B

D E

A. Tube clamp B. Tube clamp screw C.Copper tubing

8. The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

D. Compression nut

E. Valve inlet

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

DEF

E. Compression sleeve F. Shutoff valve

G. Packing nut

Style 2 - Connection to Water Line

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon

plug from the gray, coiled water tubing on the rear of the refrigerator.

3. Before attaching copper tubing to refrigerator, flush at least

2 qt (1.9 L) of water through the copper tubing and into a bucket to get rid of any particles in the water line.

4. Check for leaks around the saddle valve. Do not overtighten

clamp or sleeve. This will crush copper tubing.

5. If the gray water tube supplied with the refrigerator is not long

A B

enough, a ¹⁄₄" x ¹⁄₄" coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B C D E F G

A. Refrigerator water tubing B. Nut (provided) C. Bulb

D.Coupling (provided)

6. Turn shutoff valve ON.

7. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

E. Ferrule (purchased) F. Nut (purchased)

G. Household water line

Style 3 - Connection to Shutoff Valve

Plug in Refrigerator

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon

plug from the gray, coiled water tubing on the rear of the refrigerator.

3. Before attaching copper tubing to refrigerator, flush at least

2 qt (1.9 L) of water through the copper tubing and into a bucket to get rid of any particles in the water line.

4. Check for leaks around the saddle valve. Do not overtighten

clamp or sleeve. This will crush copper tubing.

5. Push the bulb end of the tubing into the water valve as far as it

will go. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A. Bulb B. Nut (provided)

6. Turn shutoff valve ON.

7. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Prepare the Water System

Please read before using the water system. Immediately after installation, follow the steps below to make sure

that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. The On/Off

switch is located on the top right side of the freezer compartment. Move the switch to the OFF (right) setting as shown.

NOTE: Make sure the base grille filter is properly installed and the cap is in the horizontal position.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

2. Open the freezer door and turn on the ice maker. Move the

switch to the ON (left) position. See the Use & Care Guide for further instructions on the operation of your ice maker.

■ Allow 24 hours to produce the first batch of ice.

■ Discard the first three batches of ice produced.

■ Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Level Refrigerator

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

Remove the Base Grille

3. Adjust the rear leveling bolt to bring the refrigerator level with

the side cabinets or cabinet end panels.

4. If you want, you may now use the four leveling bolts to raise

the refrigerator to reduce the gap between the refrigerator top hinge and the cabinet opening. Check that all four leveling legs still touch the floor and that the cabinet doors above the refrigerator open all the way.

1. Open the refrigerator doors to 90°.

2. Remove base grille. Grasp the grille with both hands. Lift up

and tilt the top of the grille toward you. NOTE: Do not remove the Tech Sheets fastened behind the

grille.

Level the Refrigerator

There is a set of two leveling bolts on each side of the refrigerator behind the base grille. The top bolts adjust the rear of the refrigerator, and the bottom bolts adjust the front of the refrigerator.

A. Rear leveling bolt (top) B. Front leveling bolt (bottom)

1. Use a ¹⁄₂" (12.70 mm) socket wrench to adjust the leveling

bolts. Turn the leveling bolts to the right to raise or to the left to lower the refrigerator. It may take several turns to adjust the tilt of the refrigerator.

NOTE: Do not unscrew the leveling bolts too much when lowering the refrigerator. The bolt head will start to come away from the refrigerator when in the lowest position.

2. Adjust the front leveling bolts to bring the refrigerator top

parallel with the cabinet above the refrigerator.

■ For standard cabinets, leave approximately ¹⁄₈" (3.18 mm)

gap between the refrigerator’s top hinges and the cabinets.

■ For full-overlay cabinets, leave ¹⁄₄" (6.35 mm) gap between

the refrigerator’s top hinges and the cabinets.

■ If you do not have a cabinet above the refrigerator, simply

adjust the refrigerator to make it level.

Replace Base Grille

1. Open the refrigerator doors to 90°.

2. Replace the base grille. Place the lower clips into the bottom

of the refrigerator and roll the grille up until it snaps into place.

Door Height Adjustment

TOOLS NEEDED: ⁵⁄₁₆" or adjustable wrench. IMPORTANT: Models are preset with a quarter's-thickness

difference in door height and may not need adjusting. If necessary after the refrigerator is loaded with food, follow the

steps below to adjust the door height up or down.

1. Locate the height adjustment bolt on the bottom hinge of the

refrigerator door. NOTE: For easier access to the height adjustment bolt, the

refrigerator door should be closed.

2. Turn the height adjustment bolt using the ⁵⁄₁₆" or adjustable

wrench.

■ To raise the height, turn the bolt to the right.

■ To lower the height, turn the bolt to the left.

3. Check that the doors are even at the top and bottom. If

necessary, continue to turn the height adjustment bolt.

Complete Installation

1. Turn water supply line valve to “Open” position.

2. Turn refrigerator switch to ON position. Wait a few minutes.

Check water line connections for leaks.

3. Set refrigerator and freezer compartment controls to the

midpoint setting. Check that the compressor is operating properly and that all lights are working.

NOTE: If construction will continue after refrigerator has been installed, set controls to OFF.

If refrigerator does not operate

■ Check that the circuit breaker is not tripped or household fuse

blown.

A. Top hinges B. Front of the refrigerator

■ Check that the power supply cord is plugged into a grounded

3prong outlet.

■ See “Troubleshooting” in the Use & Care Guide.

+ 16 hidden pages