Jeep Liberty 2008 User Manual

SECTION PAGE

1

INTRODUCTION

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4

INSTRUMENT PANEL AND CONTROLS

5

STARTING AND OPERATING

6

WHAT TO DO IN EMERGENCIES

7

MAINTAINING YOUR VEHICLE

8

MAINTENANCE SCHEDULES

9

IF YOU NEED CONSUMER ASSISTANCE

TABLE OF CONTENTS

.............................................................3

...............................9

...............................83

......................................... 185

.................................................273

...............................................383

...............................................395

..................................................451

..........................................459

1
2
3
4
5
6
7
8
9

10

INDEX

....................................................................469

10

CONTENTS

INTRODUCTION

1

m Introduction ...........................4

m Rollover Warning ........................4

m How To Use This Manual ..................5

m Warnings And Cautions ................... 7

m Vehicle Identification Number ...............7

m Vehicle Modifications / Alterations ...........8

4 INTRODUCTION

INTRODUCTION

This manual has been prepared with the assistance of
service and engineering specialists to acquaint you with
the operation and maintenance of your new vehicle. It is
supplemented by a Warranty Information Booklet and
various customer oriented documents. You are urged to
read these publications carefully. Following the instruc­tions and recommendations in this manual will help
assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored
in the vehicle for convenient reference and remain with
the vehicle when sold, so that the new owner will be
aware of all safety warnings.

When it comes to service, remember that your dealer
knows your vehicle best, has the factory-trained techni­cians and genuine Mopart parts, and is interested in
your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate
than other types of vehicles. This vehicle has a higher
ground clearance, and a higher center of gravity than
many passenger cars. It is capable of performing better in
a wide variety of off-road applications. Driven in an
unsafe manner, all vehicles can be caused to go out of
control. Because of the higher center of gravity, if this
vehicle is out of control it may rollover when some other
vehicles may not.

Do not attempt sharp turns or abrupt maneuvers or other
unsafe driving actions that can cause loss of vehicle
control. Failure to operate this vehicle safely may result
in an accident, rollover of the vehicle, and severe or fatal
injury. Drive carefully.

INTRODUCTION 5

belts could cut the highway death toll by 10,000 or more
each year, and could reduce disabling injuries by 2
million annually. In a rollover crash, an unbelted person
is significantly more likely to die than a person wearing
a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section
contains the information you desire.

The detailed index, at the rear of this manual, contains a
complete listing of all subjects.

1

Rollover Warning Label

Failure to use driver and passenger seat belts provided

is a major cause of severe or fatal injury. In fact, the U.S.
government notes that the universal use of existing seat

Consult the following table for a description of the
symbols that may be used on your vehicle or throughout
this owner manual:

6 INTRODUCTION

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating
procedures, which could result in an accident or bodily
injury. It also contains CAUTIONS against procedures,
which could result in damage to your vehicle. If you do
not read this entire manual, you may miss important
information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number (VIN) is found on the
left front corner of the instrument panel. The VIN is
visible from outside of the vehicle through the wind­shield. This number also appears on the Automobile
Information Disclosure Label affixed to a window on
your vehicle, the vehicle registration, and the title.

INTRODUCTION 7

1

Vehicle Identification Number

NOTE: It is illegal to remove the VIN.

8 INTRODUCTION

VEHICLE MODIFICATIONS / ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could
seriously affect its roadworthiness and safety and
may lead to an accident resulting in serious injury or
death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

m A Word About Your Keys ..................12

▫ Ignition Key Removal ...................12

▫ Key-In-Ignition Reminder ................14

m Sentry Key ............................14

▫ Replacement Keys ......................16

▫ Customer Key Programming ..............16

▫ General Information ....................17

m Steering Wheel Lock — If Equipped ..........18

▫ To Manually Lock The Steering Wheel .......18

2

▫ To Release The Steering Wheel Lock .........18

m Security Alarm System — If Equipped .........18

▫ Rearming Of The System .................19

▫ To Arm The System .....................19

▫ To Disarm The System ...................19

m Illuminated Entry System ..................20

m Remote Keyless Entry .....................20

▫ To Unlock The Doors And Liftgate ..........21

▫ To Lock The Doors And Liftgate ............22

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ To Unlatch The Liftgate Flip-Up Window .....24

▫ Using The Panic Alarm ..................24

▫ Programming Additional Transmitters ........25

▫ Battery Replacement ....................25

▫ General Information ....................26

m Remote Starting System — If Equipped ........27

▫ How To Use Remote Start ................28

m Door Locks ............................29

▫ Manual Door Locks .....................29

▫ Power Door Locks .....................31

▫ Child-Protection Door Lock System (Rear

Doors) ..............................33

m Windows .............................36

▫ Power Windows .......................36

▫ Wind Buffeting ........................39

m Liftgate ...............................40

m Occupant Restraints ......................41

▫ Lap/Shoulder Belts .....................42

▫ Lap/Shoulder Belt Untwisting Procedure .....47

▫ Seat Belt Pretensioners ...................47

▫ Enhanced Seat Belt Use Reminder System

(BeltAlert) ...........................48

▫ Automatic Locking Mode — If Equipped .....49

▫ Energy Management Feature ..............50

▫ Seat Belts And Pregnant Women ............50

▫ Seat Belt Extender ......................51

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

▫ Driver And Front Passenger Supplemental

Restraint System (SRS) - Airbag ............52

▫ Child Restraint ........................69

m Engine Break-In Recommendations ...........79

m Safety Tips ............................79

▫ Transporting Passengers .................79

▫ Lock Your Vehicle ......................80

▫ Exhaust Gas ..........................80

▫ Safety Checks You Should Make Inside The

Vehicle ..............................81

▫ Periodic Safety Checks You Should Make

Outside The Vehicle ....................82

2

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

You can insert the double-sided keys into the locks with
either side up.

Vehicle Key

The dealer that sold you your new vehicle has the key
code numbers for your vehicle locks. These numbers can
be used to order duplicate keys from your dealer. Ask
your dealer for these numbers and keep them in a safe
place.

Ignition Key Removal

Automatic Transmission

Place the selector lever in “P” (Park). Turn the key to the
ACC position and then push the key and cylinder inward
slightly and rotate the key to the LOCK position. Then
remove the key.

Ignition Key Positions

Manual Transmission — If Equipped

Turn the key to the ACC position and then push the key
and cylinder inward slightly and rotate the key to the
LOCK position. Then remove the key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

NOTE:

•

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), features such as the power
window switches, radio, power sunroof or Sky Slidert
(if equipped), and power outlets will remain active for
45 seconds after the ignition switch is turned to the
LOCK position. Opening either front door will cancel
this feature.

•

For vehicles equipped with the EVIC, features such as
the power window switches, radio, power sunroof or
Sky Slidert (if equipped), and power outlets will
remain active for up to 10 minutes after the ignition
switch is turned to the LOCK position. Opening either
front door will cancel this feature. The time for this
feature is programmable. For details, refer to “Delay
Power Off to Accessories Until Exit,” under “Personal
Settings (Customer Programmable Features),” under
“Electronic Vehicle Information Center (EVIC)” in
Section 4 of this manual.

2

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Never leave children alone in a vehicle. Leaving
children in a vehicle unattended is dangerous for a
number of reasons. A child or others could be seri­ously or fatally injured. Don’t leave the key in the
ignition. A child could operate power windows,
other controls, or move the vehicle.

CAUTION!

An unlocked vehicle is an invitation to thieves.
Always remove the key from the ignition, and lock
all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver’s door and the key is in the
ignition, a chime will sound to remind you to remove the
key.

NOTE: The Key-In-Ignition reminder only sounds
when the ignition key is placed in the LOCK or ACC
position.

SENTRY KEY

The Sentry Key Immobilizer System prevents unautho­rized vehicle operation by disabling the engine. The
system does not need to be armed or activated. Operation
is automatic, regardless of whether the vehicle is locked
or unlocked.

The system uses ignition keys, which have an embedded
electronic chip (transponder), to prevent unauthorized
vehicle operation. Therefore, only keys that are pro­grammed to the vehicle can be used to start and operate

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

the vehicle. The system will shut the engine off in two (2)
seconds if someone uses an invalid key to start the
engine.

NOTE: A key, which has not been programmed, is also
considered an invalid key even if it is cut to fit the
ignition switch lock cylinder for that vehicle.

During normal operation, after turning on the ignition
switch, the Vehicle Security Alarm Indicator Light will
turn on for three (3) seconds for a bulb check. If the light
remains on after the bulb check, it indicates that there is
a problem with the electronics. In addition, if the light
begins to flash after the bulb check, it indicates that
someone used an invalid key to start the engine. Either of
these conditions will result in the engine being shut off
after two (2) seconds.

If the Vehicle Security Alarm Indicator Light turns on
during normal vehicle operation (vehicle running for

longer than 10 seconds), it indicates that there is a fault in
the electronics. Should this occur, have the vehicle ser­viced as soon as possible.

NOTE:

•

The Sentry Key Immobilizer System is not compatible
with some after-market remote starting systems. Use
of these systems may result in vehicle starting prob­lems and loss of security protection.

•

Exxon/Mobil Speed Pass,™ additional Sentry Keys, or
any other transponder-equipped components on the
same key chain will not cause a key-related (transpon­der) fault unless the additional part is physically held
against the ignition key being used when starting the
vehicle. Cell phones, pagers, or other RF electronics
will not cause interference with this system.

All of the keys provided with your new vehicle have
been programmed to the vehicle electronics.

2

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Replacement Keys

NOTE: Only keys that are programmed to the vehicle
electronics can be used to start and operate the vehicle.
Once a Sentry Key is programmed to a vehicle, it cannot
be programmed to any other vehicle.

CAUTION!

Always remove Sentry Keys from the vehicle and
lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided
with a four-digit PIN number. Keep the PIN in a secure
location. This number is required for dealer replacement
of keys. Duplication of keys may be performed at an
authorized dealer or by using the Customer Key Pro­gramming procedure. This procedure consists of pro­gramming a blank key to the vehicle electronics. A blank
key is one, which has never been programmed.

NOTE: When having the Sentry Key Immobilizer
System serviced, bring all vehicle keys with you to the
dealer.

Customer Key Programming

If you have two valid sentry keys, you can program new
sentry keys to the system by performing the following
procedure:

1. Cut the additional Sentry Key Transponder blank(s) to
match the ignition switch lock cylinder key code.

2. Insert the first valid key into the ignition switch. Turn
the ignition switch to the “ON” position for at least 3
seconds, but no longer than 15-seconds. Then, turn the
ignition switch to the “LOCK” position and remove the
first key.

3. Insert the second valid key into the ignition switch.
Turn the ignition switch to the “ON” position within 15
seconds. After ten seconds, a chime will sound. In

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

addition, the Vehicle Security Alarm Indicator Light will
begin to flash. Turn the ignition switch to the “LOCK”
position and remove the second key.

4. Insert a blank Sentry Key into the ignition switch. Turn
the ignition switch to the “ON” position within 60
seconds. After 10 seconds, a single chime will sound. In
addition, the Vehicle Security Alarm Indicator Light will
stop flashing. To indicate that programming is complete,
the indicator light will turn on again for 3 seconds and
then turn off.

The new Sentry Key is programmed. The Keyless Entry

Transmitter will also be programmed during this pro­cedure.

Repeat this procedure to program up to 8 keys. If you do
not have a programmed sentry key, contact your dealer
for details.

NOTE: If a programmed key is lost, see your dealer to
have all remaining keys erased from the systems
memory. This will prevent the lost key from starting your
vehicle. The remaining keys must then be repro­grammed. All vehicle keys must be taken to the dealer at
the time of service to be reprogrammed.

General Information

The Sentry Key system complies with FCC rules part 15
and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be
received, including interference that may cause undes­ired operation.

2

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

STEERING WHEEL LOCK — IF EQUIPPED

Your vehicle may be equipped with a passive steering
wheel lock (manual transmission only). This lock pre­vents steering the vehicle without the ignition key. If the
steering wheel is moved a half turn in either direction
and the key is not in the ignition, the steering wheel will
lock.

To Manually Lock the Steering Wheel

With the engine running, rotate the steering wheel 1/2
revolution from straight ahead position, turn off the
engine, and remove the key. Rotate the steering wheel
slightly in both directions until the lock engages.

To Release the Steering Wheel Lock

Insert the key in the ignition and turn the wheel slightly
to the right or left to disengage the lock.

NOTE: If you turned the wheel to the right to engage
the lock, you must turn the wheel slightly to the right to

disengage it. If you turned the wheel to the left to engage
the lock, turn the wheel slightly to the left to disengage it.

SECURITY ALARM SYSTEM — IF EQUIPPED

The Vehicle Security Alarm (VSA) system monitors the
vehicle doors, liftgate, and liftgate flip-up window for
unauthorized entry and ignition for unauthorized opera­tion.

If something triggers the alarm, the system will sound
the horn intermittently, flash the headlights and tail­lights, and flash the Vehicle Security Alarm Indicator
Light in the cluster.

NOTE: The “Panic” and “Security” alarms are quite
different. Please take a moment to activate the “Panic”
and the “Security” modes to hear the differences in the
horn. In case one should go off in the future, you will
need to know which mode has been activated in order to
deactivate it.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

Rearming of the System:

If something triggers the alarm, and no action is taken to
disarm it, the system will turn off the horn after 3
minutes, turn off all of the visual signals after 15 minutes,
and then the system will rearm itself.

To Arm the System:

1. Remove the key from the ignition switch and exit the
vehicle.

2. Lock the doors and liftgate by pressing the power door
lock switch or the Lock button on the Remote Keyless
Entry (RKE) transmitter.

NOTE: The system will not arm if you lock the doors
with the manual door lock plungers or the driver’s door
lock cylinder.

3. Close all doors. The Vehicle Security Alarm Indicator
Light in the instrument cluster will flash rapidly for
about 16 seconds to signal that the system is arming.

During this period, opening any door or the liftgate will
cancel the arming process. If the system arms success­fully, the Vehicle Security Alarm Indicator Light will flash
at a slower rate to indicate the alarm is set.

NOTE: For added security, whenever the Security
Alarm is armed, the HomeLinkt/Garage Door Opener
(if equipped) is disabled as well.

To Disarm the System:

Either press the Unlock button on the RKE transmitter or
insert a valid sentry key into the ignition lock cylinder
and turn the key to the ON position.

NOTE:

•

Unlocking the doors with the manual door lock plung­ers or the driver’s door lock cylinder will not disarm
the system.

•

When the system is armed, the interior power door
lock switches will not unlock the doors.

2

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The Security Alarm System is designed to protect your
vehicle; however, you can create conditions where the
system will give you a false alarm. If the previously
described arming sequence has occurred, the system will
arm regardless of whether you are inside or outside the
vehicle. If you remain inside the vehicle and open a door,
the alarm will sound. If this occurs, disarm the system.

Tamper Alert

If something has triggered the alarm in your absence, the
horn will sound three times when you unlock the doors.
Check the vehicle for tampering.

ILLUMINATED ENTRY SYSTEM

The interior lights will turn on when you use the Remote
Keyless Entry (RKE) transmitter or open a door.

This feature also turns on the approach lighting (if so
equipped). For details, refer to “Illumination Approach,”

under “Personal Settings (Customer Programmable Fea­tures),” under “Electronic Vehicle Information Center
(EVIC)” in Section 4 of this manual.

The interior lights will fade to off after about 30 seconds
or they will immediately fade to off once the ignition
switch is turned on.

NOTE:

•

The illuminated entry system will not operate the
interior lights if the dimmer control is in the “defeat”
position (extreme downward position).

REMOTE KEYLESS ENTRY

This system allows you to lock or unlock the doors and
liftgate, open the liftgate flip-up window, or activate the
panic alarm from distances up to 23 feet (7 meters) using
a hand held radio transmitter. The transmitter need not
be pointed at the vehicle to activate the system. However,
the line of transmission must not be blocked with metal
objects when using the transmitter.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

NOTE: Inserting the key into the ignition switch dis­ables all buttons on the transmitter.

Vehicle Key

To Unlock the Doors and Liftgate:

Press and release the Unlock button on the transmitter
once to unlock the driver’s door, or twice to unlock all
doors and the liftgate. The turn signal lights will flash to
acknowledge the unlock signal. The illuminated entry
system will also turn on.

Remote Key Unlock, Driver Door/All Doors First

This feature lets you program the system to unlock either
the driver’s door or all doors and the liftgate on the first
press of the Unlock button on the transmitter. To change
the current setting, proceed as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Remote Key
Unlock,” under “Personal Settings (Customer Pro­grammable Features),” under “Electronic Vehicle In­formation Center (EVIC)” in Section 4 of this manual

•

For vehicles not equipped with the EVIC, perform the
following steps:

1. Press and hold the Lock button on a programmed (i.e.
functional) transmitter for at least 4 seconds, but no
longer than 10 seconds. Then, press and hold the Unlock
button while still holding the Lock button.

2. Release both buttons at the same time.

2

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3. Test the feature from outside the vehicle by pressing
the Lock and Unlock buttons on the transmitter.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Pressing the Lock button on the transmitter
while you are inside the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the Unlock button to
deactivate the Security Alarm.

Illuminated Approach — If Equipped

This feature activates the headlights for up to 90 seconds
when the doors are unlocked with the transmitter. The
time for this feature is programmable on vehicles
equipped with the Electronic Vehicle Information Center
(EVIC). For details, refer to “Illumination Approach,”
under “Personal Settings (Customer Programmable Fea­tures),” under “Electronic Vehicle Information Center
(EVIC)” in Section 4 of this manual.

To Lock the Doors and Liftgate:

Press and release the Lock button on the transmitter to
lock all doors and the liftgate. The turn signal lights will
flash and the horn will chirp to acknowledge the lock
signal.

Sound Horn with Lock

This feature will cause the horn to chirp when the doors
are locked with the transmitter. This feature can be
turned on or turned off. To change the current setting,
proceed as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Sound Horn with
Remote Key Lock,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic
Vehicle Information Center (EVIC)” in Section 4 of this
manual.

•

For vehicles not equipped with the EVIC, perform the
following steps:

1. Press the Lock button on a programmed (i.e. func­tional) transmitter for at least 4 seconds, but no longer
than 10 seconds. Then, press the Panic button while still
holding the Lock button.

2. Release both buttons at the same time.

3. Test the feature from outside the vehicle by pressing
the Lock button on the transmitter.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Pressing the Lock button on the transmitter
while you are inside the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the Unlock button to
deactivate the Security Alarm.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

Flash Lights with Lock

The feature will cause the turn signal lights to flash when
the doors are locked or unlocked with the transmitter.
This feature can be turned on or turned off. To change the
current setting, proceed as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Flash Lights with
Remote Key Lock,” under 9Personal Settings (Cus­tomer Programmable Features),” under “Electronic
Vehicle Information Center (EVIC)” in Section 4 of this
manual.

•

For vehicles not equipped with the EVIC, perform the
following steps:

1. Press and hold the Unlock button on a programmed
(i.e. functional) transmitter for at least 4 seconds, but no
longer than 10 seconds. Then, press and hold the Lock
button while still holding the Unlock button.

2

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Release both buttons at the same time.

3. Test the feature from outside the vehicle by pressing
the Lock and Unlock buttons on the transmitter.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Pressing the Lock button on the transmitter
while you are inside the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the Unlock button to
deactivate the Security Alarm.

To Unlatch the Liftgate Flip-Up Window:

Press the Rear Release button twice to unlatch the liftgate
flip-up window.

WARNING!

To avoid injury stand back when opening. Glass will
automatically rise.

Using the Panic Alarm

NOTE: The “Panic” and “Security” alarms are quite
different. Please take a moment to activate the “Panic”
and the “Security” modes to hear the differences in the
horn. In case one should go off in the future, you will
need to know which mode has been activated in order to
deactivate it.

To turn the panic alarm feature ON or OFF, press and
hold the Panic button on the transmitter for at least one
second and release. When the panic alarm is on, the

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

headlights and turn signal lights will flash, the horn will
pulse on and off, and the illuminated entry system will
turn on.

The panic alarm will stay on for 3 minutes unless you
turn it off by pressing the Panic button a second time or
if the vehicle speed is 5 mph (8 km/h) or greater.

During the Panic Mode, the door locks and remote
keyless entry system will function normally. Panic mode
will not disarm the security system on vehicles so
equipped.

NOTE: You may need to be close to the vehicle when
using the transmitter to turn off the panic alarm due to
the radio frequency noises emitted by the system.

Programming Additional Transmitters

Refer to SENTRY KEY “Customer Key Programming.”
in this section.

NOTE: If you do not have a programmed transmitter,

contact your dealer for details.

Battery Replacement

The recommended replacement battery is CR2032.

NOTE:

•

Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the screw from the transmitter case (if
equipped).

2

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. With the transmitter buttons facing down, use a flat
blade tool to pry the two halves of the transmitter case
apart. Make sure not to damage the seal during removal.

Separating Case Halves

3. Remove and replace the batteries. Avoid touching the
new batteries with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.

4. To assemble the transmitter case, snap the two halves
together.

5. Reinstall and tighten the screw until snug (if
equipped).

General Information

This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference that may be
received including interference that may cause undesired
operation.

NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could
void the user’s authority to operate the equipment.

If your Keyless Entry Transmitter fails to operate from a
normal distance, check for these two conditions.

1. Weak batteries in transmitter. The expected life of the
batteries is from one to two years.

2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

2

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the Remote Keyless Entry (RKE) trans­mitter to start the engine conveniently from outside the
vehicle while still maintaining security. The system has a
targeted range of 328 ft. (100 m).

Remote Start Button

NOTE: The vehicle must be equipped with an auto-

matic transmission to be equipped with Remote Start.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

How To Use Remote Start

All of the following conditions must be met before the
engine will remote start:

•

Gear selector lever in “P” (Park).

•

Doors closed.

•

Hood closed.

•

Liftgate closed.

•

Hazard switch off.

•

Brake switch inactive (brake pedal not pressed).

•

Ignition key removed from ignition switch.

•

Battery at an acceptable charge level.

•

RKE Panic button not pressed.

To Enter Remote Start Mode

Press and release the Remote Start button on
the RKE transmitter twice. The engine will start
and the vehicle will remain in the Remote Start
mode for a 15-minute cycle.

NOTE:

•

For security, power window operation and sunroof or
Sky Slidert operation (if equipped) is disabled when
the vehicle is in the Remote Start mode.

•

The engine can be started two consecutive times (two
15-minute cycles) with the RKE transmitter. However,
the ignition switch must be cycled to the ON position
before you can repeat the start sequence for a third
cycle.

To Exit Remote Start Mode without Driving the
Vehicle

Allow the engine to run for the entire 15-minute cycle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

To Exit Remote Start Mode & Drive the Vehicle

Before the end of the 15-minute cycle, press and release
the Unlock button on the RKE transmitter to unlock the
doors and disarm the Vehicle Security Alarm (if
equipped). Then, insert the key into the ignition switch
and turn the switch to the ON position.

NOTE: The ignition switch must be in the ON position
in order to drive the vehicle.

To Turn Off the Engine While in Remote Start
Mode

Press and release the remote start button one time.
NOTE: To avoid inadvertent shut downs, the system

will disable the one-time press of the remote start button
for two seconds after receiving a valid remote start
request.

DOOR LOCKS
Manual Door Locks

To lock each door, push the door lock plunger on each
door trim panel downward. To unlock each door, pull the
door lock plunger on each door trim panel upward.

Manual Lock Plunger

2

30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

If the door lock plunger is down when you shut the door,
the door will lock. Therefore, make sure the keys are not
inside the vehicle before closing the door.

NOTE: The manual door locks will not lock or unlock
the liftgate.

WARNING!

•

For personal security and safety in the event of an
accident, lock the vehicle doors as you drive as
well as when you park and leave the vehicle.

•

When leaving the vehicle always remove the key
from the ignition lock, and lock your vehicle.
Unsupervised use of vehicle equipment may cause
severe personal injuries and death.

•

Never leave children alone in a vehicle. Leaving
children in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Don’t leave the keys in
the ignition. A child could operate power win­dows, other controls, or move the vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31

Power Door Locks

A power door lock switch is on each front door trim
panel. Use this switch to lock or unlock the doors and
liftgate.

Power Door Lock Switch

If you press the power door lock switch while the key is
in the ignition, and any front door is open, the power

locks will not operate. This prevents you from acciden­tally locking your keys in the vehicle. Removing the key
or closing the door will allow the locks to operate. A
chime will sound if the key is in the ignition switch and
a door is open, as a reminder to remove the key.

Automatic Door Locks

The doors will lock automatically on vehicles with power
door locks if all of the following conditions are met:

1. The Automatic Door Locks feature is enabled.

2. The transmission is in gear.

3. All doors are closed.

4. The throttle is pressed.

5. The vehicle speed is above 15 mph (24 km/h).

6. The doors were not previously locked using the power
door lock switch or remote keyless entry transmitter.

2

32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Automatic Door Locks Programming

The Automatic Door Locks feature can be enabled or
disabled as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Personal Settings
(Customer Programmable Features)” under “Elec­tronic Vehicle Information Center (EVIC)” in Section 4
of this manual for details.

•

For vehicles not equipped with the EVIC, performing
the following procedure:

1. Close all doors and place the key in the ignition.

2. Cycle the ignition switch between LOCK and ON and
then back to LOCK 4 times ending up in the LOCK
position.

3. Depress the power door lock switch to lock the doors.

4. A single chime will indicate the completion of the
programming.

5. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Use the Automatic Door Locks feature in accor­dance with local laws.

Automatic Unlock Doors on Exit

The doors will unlock automatically on vehicles with
power door locks if:

1. The Automatic Unlock Doors On Exit feature is en­abled.

2. The transmission was in gear and the vehicle speed
returned to 0 mph (0 km/h).

3. The transmission is in “N” (Neutral) or “P” (Park)

4. The driver door is opened.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33

5. The doors were not previously unlocked.

6. The vehicle speed is 0 mph (0 km/h).

Automatic Unlock Doors on Exit Programming

The Automatic Unlock Doors On Exit feature can be
enabled or disabled as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Personal Settings
(Customer Programmable Features)” under “Elec­tronic Vehicle Information Center (EVIC)” in Section 4
of this manual for details.

•

For vehicles not equipped with the EVIC, performing
the following procedure:

1. Close all doors and place the key in the ignition.

2. Cycle the ignition switch between LOCK and ON and
then back to LOCK 4 times ending up in the LOCK
position.

3. Depress the power door unlock switch to unlock the
doors.

4. A single chime will indicate the completion of the
programming.

5. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Use the Automatic Unlock Doors On Exit feature
in accordance with local laws.

Child-Protection Door Lock System (Rear Doors)

To provide a safer environment for small children riding
in the rear seats, the rear doors are equipped with a child
protection door lock system.

To Engage the Child Protection Door Lock

1. Open the rear door.

2

34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Insert the tip of the ignition key into the child lock
control and rotate it to the lock position.

Inserting Ignition Key

3. Repeat Steps 1 and 2 on the opposite rear door.

NOTE: When the child lock system is engaged, the door
can be opened only by using the outside door handle
even though the inside door lock is in the unlocked
position.

WARNING!

Avoid trapping anyone in a vehicle in a collision.
Remember that the rear doors can only be opened
from the outside when the child protection locks are
engaged.

NOTE:

•

After engaging the child protection door lock system,
always test the door from the inside to make certain it
is in the desired position.

•

For emergency exit with the system engaged, move
the lock plunger up (unlocked position), roll down the
window, and open the door with the outside door
handle.

To Disengage the Child Protection Door Lock

1. Open the rear door.

2. Insert the tip of the ignition key into the child lock
control and rotate it to the unlock position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

2

Inserting Ignition Key

3. Repeat Steps 1 and 2 on the opposite rear door.
NOTE: After disengaging the child protection door lock

system, always test the door from the inside to make
certain it is in the desired position.

36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WINDOWS
Power Windows

The window controls on the driver’s door trim panel
control all the door windows.

Power Window Switches

There are single window controls on each passenger door
trim panel, which operate the passenger door windows.
The window controls will operate when the ignition
switch is in the ON or ACC position.

WARNING!

Never leave children in a vehicle, with the keys in
the ignition switch. Occupants, particularly unat­tended children, can become entrapped by the win­dows while operating the power window switches.
Such entrapment may result in serious injury or
death.

Auto Down Feature

The driver power window switch has an “Auto Down”
feature. Press the window switch past the first detent,
release, and the window will go down automatically.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37

To open the window part way, press the window switch
to the first detent and release it when you want the
window to stop.

To stop the window from going all the way down during
the auto-down operation, pull up on the switch briefly.

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power window switches
will remain active for 45 seconds after the ignition switch
is turned to the LOCK position. Opening either front
door will cancel this feature.

For vehicles equipped with the EVIC, the power window
switches will remain active for up to 10 minutes after the
ignition switch is turned to the LOCK position. Opening
either front door will cancel this feature. The time is
programmable. For details, refer to “Delay Power Off to

Accessories Until Exit,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic Ve­hicle Information Center (EVIC)” in Section 4 of this
manual.

Auto Up Feature with Anti-Pinch Protection — If
Equipped

On some models, the driver’s power window switch has
an “Auto Up” feature. Pull the window switch up to the
second detent, release, and the window will go up
automatically.

To stop the window from going all the way up during the
auto-up operation, push down on the switch briefly.

To close the window part way, pull the window switch
up to the first detent and release when you want the
window to stop.

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power window switches

2

38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

will remain active for 45 seconds after the ignition switch
is turned to the LOCK position. Opening either front
door will cancel this feature.

For vehicles equipped with the EVIC, the power window
switches will remain active for up to 10 minutes after the
ignition switch is turned to the LOCK position. Opening
either front door will cancel this feature. The time is
programmable. For details, refer to “Delay Power Off to
Accessories Until Exit,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic Ve­hicle Information Center (EVIC)” in Section 4 of this
manual.

NOTE:

•

If the window runs into any obstacle during auto­closure, it will reverse direction and then stop. Remove
the obstacle and use the window switch again to close
the window.

•

Any impact due to rough road conditions may trigger
the auto reverse function unexpectedly during auto­closure. If this happens, pull the switch lightly to the
first detent and hold to close window manually.

WARNING!

There is no anti-pinch protection when the window
is almost closed. Be sure to clear all objects from the
window before closing.

Window Lockout Switch

The window lockout switch on the driver’s door trim
panel allows you to disable the window control on the
other doors. To disable the window control on the other
doors, press and release the window lock button (setting
it in the down position). To enable the window controls,
press and release the window lock button again (setting
it in the up position).

Window Lockout Switch

Reset

It may be necessary at some point in time to reactivate the
auto-up feature. To do so, perform the following procedure:

1. Pull the window switch up to close window com­pletely and continue to hold the switch up for an
additional two seconds after the window is closed.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39

2. Push the window switch down firmly to the second
detent to open the window completely and continue to
hold the switch down for an additional two seconds after
the window is fully open.

Wind Buffeting

Wind buffeting can be described as the perception of
pressure on the ears or a helicopter type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof or Sky Slidert (if
equipped) in certain open or partially open positions.
This is a normal occurrence and can be minimized. If the
buffeting occurs with the rear windows open, then open
the front and rear windows together to minimize the
buffeting. If the buffeting occurs with the sunroof or Sky
Slidert open, adjust the sunroof or Sky Slidert opening
to minimize the buffeting or open any window.

2

40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

LIFTGATE

To open the liftgate, pull up (squeeze) on the handle and
lift.

Liftgate Release

NOTE: Use the power door lock switch on either front

door trim panel or the Remote Keyless Entry (RKE)
transmitter to lock and unlock the liftgate. The manual
door locks on the doors and the driver’s door lock
cylinder will not lock and unlock the liftgate.

WARNING!

Driving with the liftgate open can allow poisonous
exhaust gases into your vehicle. You and your pas­sengers could be injured by these fumes. Keep the
liftgate closed when you are operating the vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41

OCCUPANT RESTRAINTS

Some of the most important safety features in your
vehicle are the restraint systems. These include the front
and rear seat belts for the driver and all passengers, front
airbags for both the driver and front passenger, and side
curtain airbags for the driver and passengers seated next
to a window. If you will be carrying children too small for
adult-size belts, your seat belts also can be used to hold
infant and child restraint systems.

Please pay close attention to the information in this
section. It tells you how to use your restraint system
properly to keep you and your passengers as safe as
possible.

WARNING!

In a collision, you and your passengers can suffer
injuries, including fatalities, if you are not properly
buckled up. You can strike the interior of your
vehicle or other passengers, or you can be thrown out
of the vehicle. Always be sure you and others in your
vehicle are buckled up properly.

Buckle up even though you are an excellent driver, even
on short trips. Someone on the road may be a poor driver
and cause a collision that includes you. This can happen
far away from home or on your own street.

Research has shown that seat belts save lives, and they
can reduce the seriousness of injuries in a collision. Some
of the worst injuries happen when people are thrown
from the vehicle. Seat belts reduce the possibility of
ejection and the risk of injury caused by striking the

2

42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

inside of the vehicle. Everyone in a motor vehicle should
be belted at all times to reduce or prevent injuries.

Lap/Shoulder Belts

All seating positions in your vehicle have combination
lap/shoulder belts. The belt webbing retractor is de­signed to lock during very sudden stops or collisions.
This feature allows the shoulder part of the belt to move
freely with you under normal conditions. However, in a
collision, the belt will lock and reduce your risk of
striking the inside of the vehicle or being thrown out.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in these areas
are more likely to be seriously injured or killed.

• Do not allow people to ride in any area of your vehicle that is
not equipped with seats and seat belts.

• Be sure everyone in your vehicle is in a seat and using a seat belt
properly.

• Wearing a seat belt incorrectly is dangerous. Seat belts are
designed to go around the large bones of your body. These are
the strongest parts of your body and can take the forces of a
collision the best.

• Wearing your belt in the wrong place could make your injuries
in a collision much worse. You might suffer internal injuries, or
you could even slide out of part of the belt. Follow these
instructions to wear your seat belt safely and to keep your
passengers safe, too.

• Two people should never be belted into a single seat belt.
People belted together can crash into one another in an accident,
hurting one another badly. Never use a lap/shoulder belt or a lap
belt for more than one person, no matter what their size.

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and
adjust the seat.

2. The seat belt latch plate is above the back of your seat.
Grasp the latch plate and pull out the belt. Slide the latch
plate up the webbing as far as necessary to make the belt
go around your lap.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43

2

Latch Plate

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3. When the belt is long enough to fit, insert the latch
plate into the buckle until you hear a “click.”

Latch Plate To Buckle

WARNING!

• A belt that is buckled into the wrong buckle will not

protect you properly. The lap portion could ride too high
on your body, possibly causing internal injuries. Always
buckle your belt into the buckle nearest you.

• A belt that is too loose will not protect you as well. In a

sudden stop, you could move too far forward, increasing
the possibility of injury. Wear your seat belt snugly.

• A belt that is worn under your arm is very dangerous.

Your body could strike the inside surfaces of the vehicle
in a collision, increasing head and neck injury. A belt
worn under the arm can cause internal injuries. Ribs
aren’t as strong as shoulder bones. Wearthe belt over your
shoulder so that your strongest bones will take the force
in a collision.

• A shoulder belt placed behind you will not protect you

from injury during a collision. You are more likely to hit
your head in a collision if you do not wear your shoulder
belt. The lap and shoulder belt are meant to be used
together.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

4. Position the lap belt across your thighs, below your
abdomen. To remove slack in the lap belt portion, pull up
a bit on the shoulder belt. To loosen the lap belt if it is too
tight, tilt the latch plate and pull on the lap belt. A snug
belt reduces the risk of sliding under the belt in a
collision.

WARNING!

• A lap belt worn too high can increase the risk of
injury in a collision. The belt forces won’t be at the
strong hip and pelvic bones, but across your abdo­men. Always wear the lap part of your seat belt as
low as possible and keep it snug.

• Atwisted belt can’t do its job as well. In a collision,
it could even cut into you. Be sure the belt is straight.
If you can’t straighten a belt in your vehicle, take it to
your authorized dealer and have it fixed.

5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

2

Removing Slack From Belt

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

6. To release the belt, push the red button on the buckle.
The belt will automatically retract to its stowed position.
If necessary, slide the latch plate down the webbing to
allow the belt to retract fully.

WARNING!

A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do
not disassemble or modify the system. Seat belt
assemblies must be replaced after an accident if they
have been damaged (bent retractor, torn webbing,
etc.).

Adjustable Upper Shoulder Belt Anchorage

In the front seating positions, the shoulder belt can be
adjusted upward or downward to position the belt away
from your neck. Press the release button to release the
anchorage, and then move it up or down to the position
that serves you best.

Adjusting Upper Shoulder Belt

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

As a guide, if you are shorter than average, you will
prefer a lower position, and if you are taller than average,
you will prefer a higher position. When you release the
anchorage, try to move it up and down to make sure that
it is locked in position.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the
anchor point.

2. At about 6 to 12 inches (15 to 30 cm) above the latch
plate, grasp and twist the belt webbing 180° to create a
fold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.

4. Continue to slide the latch plate up until it clears the
folded webbing.

Seat Belt Pretensioners

The driver and front passenger seat belts are equipped
with pretensioning devices that are designed to remove
any slack from the seat belt systems in the event of a
collision. These devices improve the performance of the
seat belt by assuring that the belt is tight around the
occupant early in a collision. Pretensioners work for all
size occupants, including those in child restraints.

NOTE: These devices are not a substitute for proper seat
belt placement by the occupant. The seat belt must still be
worn snugly and positioned properly.

The pretensioners are triggered by the Occupant Re­straint Controller (ORC). Like the front airbags, the
pretensioners are single use items. After a collision that is
severe enough to deploy the airbags and pretensioners,
both must be replaced.

2

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Enhanced Seat Belt Use Reminder System (BeltAlert)

If the driver’s or front passenger’s seat belt has not been
buckled within 60 seconds of starting the vehicle, and if
the vehicle speed is greater than 5 mph (8 km/h), the
Enhanced Warning System (BeltAlert) will alert the
driver or front passenger to buckle their seat belt. The
driver should also instruct all other occupants to buckle
their seat belts. Once the warning is triggered, the
Enhanced Warning System (BeltAlert) will continue to
chime and flash the Seat Belt Reminder Light for 96
seconds or until the driver’s or front passenger’s seat belt
is buckled. The Enhanced Warning System (BeltAlert)
will be reactivated if the driver’s or front passenger’s seat
belt is unbuckled for more than 10 seconds and the
vehicle speed is greater than 5 mph (8 km/h).

BeltAlert Programming

The Enhanced Warning System (BeltAlert) can be en­abled or disabled by your authorized dealer or by
performing the following steps:

NOTE: DaimlerChrysler does not recommend deacti­vating the Enhanced Warning System (BeltAlert).

1. With all doors closed, and the ignition switch in any
position except ON or START, buckle the driver’s seat
belt.

2. Turn the ignition switch to the ON position, but do not
start the engine. Wait for the Seat Belt Reminder Light to
turn off and then proceed to the next step.

NOTE: You must perform the following steps within 60
seconds of turning the ignition switch to the ON position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

3. Within 60 seconds of turning the ignition switch to the
ON position, unbuckle and then re-buckle the driver’s
seat belt at least three times within 10 seconds, ending
with the seat belt buckled.

NOTE: Watch for the Seat Belt Reminder Light to turn
on while unbuckling the seat belt and turn off while
re-buckling the seat belt. It may be necessary to retract
the seat belt.

4. Turn the ignition switch to the LOCK position. A
single chime will sound to signify that you have success­fully completed the programming.

The Enhanced Warning System (BeltAlert) can be reacti­vated by repeating this procedure.

NOTE: When the Enhanced Warning System (BeltAlert)
is deactivated, the Seat Belt Reminder Light will continue
to illuminate as long as the driver’s seat belt is unbuck­led.

Automatic Locking Mode — If Equipped

In this mode, the shoulder belt is automatically pre­locked. However, the belt will still retract to remove any
slack in the shoulder belt.

When To Use The Automatic Locking Mode

Anytime a child safety seat is installed in the rear
outboard seating position. Children 12 years old and
under should be properly restrained in the rear seat
whenever possible.

How To Use The Automatic Locking Mode

1. Buckle the combination lap and shoulder belt.

2. Grasp the shoulder portion and pull downward until
the entire belt is extracted.

3. Allow the belt to retract. As the belt retracts, you will
hear a clicking sound. This indicates the safety belt is
now in the automatic locking mode.

2

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

How to Disengage The Automatic Locking Mode

Disconnect the combination lap/shoulder belt from the
buckle and allow it to retract completely to disengage the
automatic locking mode and activate the vehicle sensitive
(emergency) locking mode.

Energy Management Feature

This vehicle has a safety belt system with an energy
management feature in the front seating positions to help
further reduce the risk of injury in the event of a head-on
collision.

This safety belt system has a retractor assembly that is
designed to release webbing in a controlled manner. This
feature is designed to help reduce the belt force acting on
the occupant’s chest.

WARNING!

•

The belt and retractor assembly must be replaced
if the seat belt assembly “automatic locking retrac­tor” feature or any other seat belt function is not
working properly when checked according to the
procedures in the Service Manual.

•

Failure to replace the belt and retractor assembly
could increase the risk of injury in collisions.

Seat Belts and Pregnant Women

We recommend that pregnant women use the seat belts
throughout their pregnancy. Keeping the mother safe is
the best way to keep the baby safe.

Pregnant women should wear the lap part of the belt
across the thighs and as snug across the hips as possible.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51

Keep the belt low so that it does not come across the
abdomen. That way the strong bones of the hips will take
the force if there is a collision.

Seat Belt Extender

If a seat belt is too short, even when fully extended, and
when the adjustable upper shoulder belt anchorage (if so
equipped) is in its lowest position, your authorized
dealer can provide you with a seat belt extender. This
extender should be used only if the existing belt is not
long enough. When it is not required, remove the ex­tender, and store it.

WARNING!

Using a seat belt extender when not needed can
increase the risk of injury in a collision. Only use
when the lap belt is not long enough when it is worn
low and snug, and in the recommended seating
positions. Remove and store the extender when not
needed.

2

52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag

This vehicle has airbags for both the driver and front
passenger as a supplement to the seat belt restraint
systems. The driver’s airbag is mounted in the steering
wheel. The passenger’s front airbag is mounted in the
instrument panel, above the glove compartment. The
words SRS AIRBAG are embossed on the airbag covers.

1 — Driver Airbag
2 — Passenger Airbag

NOTE: The front airbags are certified to the Federal
regulations that allow less forceful deployment.

The front airbags have a multistage inflator design. This
may allow the airbag to have different rates of inflation
that are based on collision severity and occupant size.
The front passenger airbag is also certified to the Federal
regulations that define Occupant Classification (refer to
information on Occupant Classification System in this
section).

This vehicle is equipped with side curtain airbags to
protect the driver and the front and rear passengers
sitting next to a window. They are located above the side
windows. Their covers are also labeled SRS AIRBAG.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53

2

Window Airbag Location

NOTE: Airbag covers may not be obvious in the interior

trim; but they will open to allow airbag deployment.

54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

• Do not put anything on or around the front and side
curtain airbag covers or attempt to manually open
them. You may damage the airbags and you could be
injured because the airbags are no longer functional.
These protective covers for the airbag cushions are
designed to open only when the airbags are inflating.

• Do not stack luggage or other cargo up high enough to
block the location of the side curtain airbag. The area
where the side curtain airbag is located should remain
free from any obstructions.

• Do not have any accessory items installed which will
alter the roof, including adding a sunroof to your
vehicle. Do not add roof racks that require permanent
attachments (bolts or screws) for installation on the
vehicle roof. Do not drill into the roof of the vehicle
for any reason.

• Do not cover or place items on the airbag covers. These
items may cause serious injury during inflation.

Along with the seat belts, the front airbags provide
improved protection for the driver and front passenger.
Side Curtain Airbags also work with seat belts to im­prove occupant protection.

The seat belts are designed to protect you in many types
of collisions. The front airbags deploy in moderate to
severe collisions. The Side Curtain Airbag will also
trigger on the crash side of the vehicle in moderate to
severe side collisions or on both sides of the vehicle in
rollover collisions. In certain types of collisions, both the
front and side airbags may be triggered. However, even
in collisions where the airbags deploy, you need the seat
belts to keep you in the right position for the airbags to
protect you properly.

NOTE: The passenger front airbag may not deploy even
when the driver front airbag has; particularly if the
Occupant Classification System has determined the pas­senger seat is empty or is occupied by someone that is

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55

classified in a category other than that of an adult (refer
to information on Occupant Classification System in this
section). This could be a child, teenager, or even a small
size adult.

Here are some simple steps you can take to minimize
the risk of harm from a deploying airbag.

1. Children 12 years old and under should always ride
buckled up in the rear seat.

Infants in rear facing child restraints should NEVER ride
in the front seat of a vehicle with a passenger front airbag.
An airbag deployment could cause severe injury or death
to infants in that position.

Children that are not big enough to wear the vehicle seat
belt properly should be secured in the rear seat in child
restraints or belt-positioning booster seats. Older chil­dren who do not use child restraints or belt-positioning

booster seats should ride properly buckled up in the rear
seat. Never allow children to slide the shoulder belt
behind them or under their arm.

If a child from 1 to 12 years old must ride in the front
passenger seat because the vehicle is crowded, move the
seat as far back as possible, and use the proper child
restraint (refer to information on Child Restraint in this
section).

You should read the instructions provided with your
child restraint to make sure that you are using it properly.

2. All occupants should use their lap and shoulder belts
properly.

3. The driver and front passenger seats should be moved
back as far as practical to allow the front airbags room to
inflate.

2

56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

4. Do not lean against the door or window, airbags will
inflate forcefully into the space between you and the
door.

5. If the airbag system in this vehicle needs to be
modified to accommodate a disabled person, contact the
Customer Center. Phone numbers are provided under “If
You Need Assistance” in Section 9 of this manual.

WARNING!

•

Relying on the airbags alone could lead to more
severe injuries in a collision. The airbags work
with your seat belt to restrain you properly. In
some collisions, the airbags won’t deploy at all.
Always wear your seat belts even though you have
airbags.

•

Being too close to the steering wheel or instrument
panel during airbag deployment could cause seri­ous injury. Airbags need room to inflate. Sit back,
comfortably extending your arms to reach the
steering wheel or instrument panel.

•

The side curtain airbags need room to inflate. Do
not lean against the door or window. Sit upright in
the center of the seat.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57

Airbag System Components

The airbag system consists of the following:

•

Occupant Restraint Controller (ORC)

•

Airbag Warning Light

•

Driver Airbag

•

Front Passenger Airbag

•

Side Curtain Airbags above Side Windows

•

Side Remote Acceleration Sensors

•

Steering Wheel and Column

•

Instrument Panel

•

Interconnecting Wiring

•

Front Acceleration Sensors

•

Driver and Front Passenger Seat Belt Pretensioner and
Retractor

•

Front Passenger Seat Track Position Sensors

•

Occupant Classification System (OCS) — Front Pas­senger Seat Only

−

Occupant Classification Module (OCM)

−

Passenger Airbag Disable (PAD) Indicator Light

−

Weight Sensors

How The Airbag System Works

The Occupant Restraint Controller (ORC) determines

•

if a frontal, side, or rollover collision is severe enough
to require the airbags to inflate. The front airbag
inflators are designed to provide different rates of
airbag inflation from direction provided by the ORC.
The ORC may also modify the rate of inflation based
on the occupant size. The ORC receives this data from
the Occupant Classification Module (OCM). The ORC
will detect roll over, but not rear impacts.

2

58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The ORC also monitors the readiness of the electronic
parts of the system whenever the ignition switch is in
the START or ON position. These include all of the
items listed above except the Passenger Airbag Disable
(PAD) Indicator Light, the instrument panel, and the
steering wheel and column. If the key is in the LOCK
position, in the ACC position, or not in the ignition,
the airbags are not on and they will not inflate.

The ORC also turns on the “Airbag Warning
Light” and “PAD Indicator Light” for 6 to 8
seconds as a self-check when the ignition is

first turned ON. After the self-check, the
“Airbag Warning Light” will turn off. The “PAD
Indicator Light” will function normally (refer to infor­mation on Passenger Airbag Disable (PAD) Indicator
Light in this section). If the ORC detects a malfunction
in any part of the system, it turns on the “Airbag

Warning Light” either momentarily or continuously. A
single chime will sound if the light comes on again
after initial start up.

WARNING!

Ignoring the “Airbag Warning Light” in your instru­ment panel could mean you won’t have the airbags to
protect you in a collision. If the light does not come
on, stays on after you start the vehicle, or if it comes
on as you drive, have the airbag system checked right
away.

•

The Occupant Classification System (OCS) is part of
a Federally regulated safety system required for this
vehicle. It is designed to turn off the front passenger
airbag for an empty seat and for occupants classified
in a category other than that of an adult. This could be
a child, teenager, or even a small size adult.

NOTE: Children 12 years and under should always ride
buckled up in a rear seat in an appropriate child restraint.

•

The Passenger Airbag Disable (PAD) Indicator Light
(an amber light located in the center of the instrument
panel) tells the driver and front passenger when the
front passenger airbag is turned off. The “PAD Indi­cator Light” illuminates the words 9PASS AIR BAG
OFF9 to show that the passenger airbag will not inflate
during a collision requiring airbags. When the front
passenger seat is empty or when very light objects are
placed on the seat, the passenger airbag will not inflate
even though the “PAD Indicator Light” is not illumi­nated.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59

2

Indicator Light Location

The “PAD Indicator Light” should not be illuminated
when an adult passenger is properly seated in the
front passenger seat. In this case, the airbag is ready to
be inflated if a collision requiring an airbag occurs. For
all other occupants, the “PAD Indicator Light” will be
illuminated indicating that the front passenger airbag

60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

is turned off and it will not inflate. If the “PAD
Indicator Light” is not illuminated, DO NOT assume
the airbag is turned off and move the child restraint to
the rear seat. A deploying passenger airbag can cause
death or serious injury to a child in a rear facing infant
seat.

NOTE: Even though this vehicle is equipped with an
Occupant Classification System, children 12 years and
under should always ride buckled up in a rear seat in an
appropriate child restraint.

Passenger Air-

Front Passenger

Seat Occupant

bag Disable

(PAD) Indicator

Airbag Status

Light

Adult OFF ON

Grocery Bags,

Heavy Brief-

cases, and Other

ON OFF

Relatively Light

Objects

Empty or Very

Small Objects

OFF* OFF

* Since the system senses weight, some small objects

will turn the PAD Indicator Light on.

The OCS classifies an occupant using weight sensors
mounted in the base of the front passenger seat. Any
weight on the seat will be sensed by the system. Objects
hanging on the seat or other passengers pushing down
on the seat will also be sensed. The weight of an adult

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61

will cause the system to turn the airbag on. In this case,
the OCS has classified the occupant of the seat as an
adult. An adult occupant needs to sit in a normal position
(with their feet on or near the floor) in order to be
properly classified. Reclining the seat back too far may
change how an occupant is classified by the OCS.

Drivers and adult passengers should verify that the
“PAD Indicator Light” is not illuminated when an adult
is riding in the front passenger seat. If an adult occu­pant’s weight is transferred to another part of the vehicle
(like the door or instrument panel), the weight sensors in
the seat may not properly classify the occupant. Objects
lodged under the seat or between the seat and the center
console can prevent the occupant’s weight from being
measured properly and may result in the occupant being
improperly classified. Ensure that the front passenger
seat back does not touch anything placed on the back seat

because this can also affect occupant classification. Also,
if you fold down the rear seat check to be sure it doesn’t
touch the front passenger seat.

If the front passenger seat is damaged in any way, it
should only be serviced by an authorized dealer. If the
seat is removed (or even if the seat attachment bolts are
loosened or tightened in any way), take the vehicle to an
authorized dealer.

If there is a fault present in the OCS, the “Airbag Warning
Light” (a red light located in the center of the instrument
cluster directly in front of the driver) will be turned on.
This indicates that you should take the vehicle to an
authorized dealer. The “Airbag Warning Light” is turned
on whenever there is a fault that can affect the operation
of the airbag system. If there is a fault present in the OCS,
both the “PAD Indicator Light” and the “Airbag Warning
Light” are illuminated to show that the passenger airbag
is turned off until the fault is cleared. If an object is

2

62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

lodged under the seat and interferes with operation of
the weight sensors, a fault will occur which turns on both
the “PAD Indicator Light” and the “Airbag Warning
Light.” Once the lodged object is removed, the fault will
be automatically cleared after a short period of time.

•

The Driver and Passenger Airbag/Inflator Units are
located in the center of the steering wheel and the
passenger side of the instrument panel. When the ORC
detects a collision requiring the airbags, it signals the
inflator units. A large quantity of nontoxic gas is
generated to inflate the front airbags. Different airbag
inflation rates are possible, based on collision severity
and occupant size. The steering wheel hub trim cover
and the upper passenger side of the instrument panel
separate and fold out of the way, as the bags inflate to
their full size. The bags fully inflate in about 50 - 70
milliseconds. This is about half of the time that it takes
to blink your eyes. The bags then quickly deflate while
helping to restrain the driver and front passenger. The

driver’s front airbag gas is vented through the vent
holes in the sides of the airbag. The passenger’s front
airbag gas is vented through the vent holes in the sides
of the airbag. In this way, the airbags do not interfere
with your control of the vehicle.

•

The Occupant Classification Module (OCM) is lo­cated beneath the front passenger seat. The OCM
classifies the occupant into categories based on the
measurements made by the seat weight sensors. The
OCM communicates with the Occupant Restraint Con­troller (ORC). The ORC uses the occupant category to
determine whether the front passenger airbag should
be turned off. It also determines the rate of airbag
inflation during a collision.

•

Your vehicle has four Weight Sensors located between
the seat and the floor pan. The weight sensors measure
applied weight and transfers that information to the
OCM.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63

•

The Side Impact SRS Side Curtain Airbags are de­signed to activate only in certain side collisions and
rollover events. When the ORC detects a collision
requiring the side curtain airbag to inflate, it signals
the inflators on the crash side of the vehicle or both
sides of the vehicle for a rollover event. A quantity of
nontoxic gas is generated to inflate the side curtain
airbag. The inflating side curtain airbag pushes the
outside edge of the headliner out of the way and
covers the window. The airbag inflates in about 30
milliseconds (about one quarter of the time that it
takes to blink your eyes) with enough force to injure
you if you are not belted and seated properly, or if
items are positioned in the area where the side curtain
airbag inflates. This especially applies to children. The

1

side curtain airbag is only about 3

⁄2inches (9 cm) thick

when it is inflated.

The front passenger seat assembly contains critical com­ponents that affect the front passenger airbag deploy­ment. Correctly functioning front passenger seat compo­nents are critical for the Occupant Classification System
(OCS) to properly classify the front passenger and calcu­late the proper airbag deployment. Do not make any
modifications to the front passenger seat components or
assembly.

The following requirements must be strictly adhered to:

•

Do not modify the front passenger seat assembly or
components in any way.

•

At no time should any supplemental restraint system
(SRS) component or SRS related component or fas­tener be modified or replaced with any part except
those which are approved by DaimlerChrysler/
Mopar.

2

64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Unapproved modifications or service procedures to
the front passenger seat assembly or its related com­ponents may inadvertently change the airbag deploy­ment in case of a frontal crash. This could result in
death or serious injury to the front seat passenger if
the vehicle is involved in an accident. A modified
vehicle may not comply with required Federal Motor
Vehicle Safety Standards (FMVSS).

If A Deployment Occurs

The airbag system is designed to deploy when the
Occupant Restraint Controller (ORC) detects a moderate­to-severe collision, to help restrain the driver and front
passenger, and then to immediately deflate.

NOTE: A collision that is not severe enough to need
airbag protection will not activate the system. This does
not mean something is wrong with the airbag system.

If you do have a collision, which deploys the airbags, any
or all of the following may occur:

•

The nylon airbag material may sometimes cause abra­sions and/or skin reddening to the driver and front
passenger as the airbags deploy and unfold. The
abrasions are similar to friction rope burns or those
you might get sliding along a carpet or gymnasium
floor. They are not caused by contact with chemicals.
They are not permanent and normally heal quickly.
However, if you haven’t healed significantly within a
few days, or if you have any blistering, see your doctor
immediately.

•

As the airbags deflate, you may see some smoke-like
particles. The particles are a normal by-product of the
process that generates the nontoxic gas used for airbag
inflation. These airborne particles may irritate the skin,
eyes, nose, or throat. If you have skin or eye irritation,
rinse the area with cool water. For nose or throat
irritation, move to fresh air. If the irritation continues,
see your doctor. If these particles settle on your
clothing, follow the garment manufacturer’s instruc­tions for cleaning.

•

It is not advisable to drive your vehicle after the
airbags have deployed. If you are involved in another
collision, the airbags will not be in place to protect you.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65

WARNING!

Deployed airbags and seat belt pretensioners cannot
protect you in another collision. Have the airbags,
seat belt pretensioner, and seat belt retractor assem­bly replaced by an authorized dealer as soon as
possible. Also, have the Occupant Classification Sys­tem serviced as well.

Enhanced Accident Response System

In the event of an impact that causes airbag deployment,
with the vehicle stopped, and the vehicle communication
network intact, and the power intact, the Enhanced
Accident Response System performs the following func­tions:

•

Cuts off fuel to the engine.

•

Flashes hazard lights.

2

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

•

Turns on the interior lights, which remain on as long as
the battery has power or until the ignition key is
removed.

•

Unlocks the doors automatically.

NOTE: The interior lights can only be deactivated if the
key is removed from the ignition switch or the vehicle is
driven.

Maintaining Your Airbag System

WARNING!

• Modifications to any part of the airbag system could cause it to fail when
you need it. You could be injured if the airbag system is not there to
protect you. Do not modify the components or wiring, including adding
any kind of badges or stickers to the steering wheel hub trim cover or the
upper passenger side of the instrument panel. Do not modify the front
bumper or vehicle body structure.

• Do not attempt to modify any part of your advanced airbag system. The
airbag may inflate accidentally or may not function properly if modifica­tions are made. Take your vehicle to an authorized dealer for any advanced
airbag system service. If your seat including your trim cover and cushion
needs to be serviced in any way (including removal or loosening/
tightening of seat attachment bolts), take the vehicle to your authorized
dealer. Only manufacturer approved seat accessories may be used. If it is
necessary to modify an advanced airbag system for persons with disabili­ties, contact your authorized dealer.

• Do not place or hang any items such as add-on video players on the front
passenger seat back. The additional weight may cause the Occupant
Classification System to be unable to classify the front seat passenger
correctly. This could allow the passenger frontal airbag to inflate when it
is not desired.

• It is dangerous to try to repair any part of the airbag system yourself. Be
sure to tell anyone who works on your vehicle that it has an airbag system.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67

NOTE:

apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate

Airbag Warning Light

You will want to have the airbag system ready to inflate
for your protection in an impact. The airbag system is
designed to be maintenance free. If any of the following
occurs, have an authorized dealer service the system
promptly:

•

•

•

Perchlorate Material – special handling may

The Airbag WarningLight does not come on or flickers
during the 6 to 8 seconds when the ignition switch is
first turned on.

The light remains on or flickers after the 6 to 8 second
interval.

The light flickers or comes on and remains on while
driving.

Event Data Recorder (EDR)

In the event of an accident, your vehicle is designed to
record up to 5-seconds of specific vehicle data parameters
(see the following list) in an event data recorder prior to
the moment of airbag deployment, or near deployment,
and up to a quarter second of high-speed deceleration
data during and/or after air bag deployment or near­deployment. EDR data are ONLY recorded if an airbag
deploys, or nearly deploys, and are otherwise unavail­able.

NOTE:

•

A near-deployment event occurs when the airbag
sensor detects severe vehicle deceleration usually in­dicative of a crash, but not severe enough to warrant
airbag deployment.

•

Under certain circumstances, EDR data may not be
recorded (e.g., loss of battery power).

2

68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

In conjunction with other data gathered during a com­plete accident investigation, the electronic data may be
used by DaimlerChrysler Corporation and others to learn
more about the possible causes of crashes and associated
injuries in order to assess and improve vehicle perfor­mance. In addition to crash investigations initiated by
DaimlerChrysler Corporation, such investigations may
be requested by customers, insurance carriers, govern­ment officials, and professional crash researchers, such as
those associated with universities, and with hospital and
insurance organizations.

In the event that an investigation is undertaken by
DaimlerChrysler Corporation (regardless of initiative),
the company or its designated representative will first
obtain permission of the appropriate custodial entity for
the vehicle (usually the vehicle owner or lessee) before
accessing the electronic data stored, unless ordered to
download data by a court with legal jurisdiction (i.e.,
pursuant to a warrant). A copy of the data will be

provided to the custodial entity upon request. General
data that does not identify particular vehicles or crashes
may be released for incorporation in aggregate crash
databases, such as those maintained by the US govern­ment and various states. Data of a potentially sensitive
nature, such as would identify a particular driver, ve­hicle, or crash, will be treated confidentially. Confidential
data will not be disclosed by DaimlerChrysler Corpora­tion to any third party except when:

1. Used for research purposes, such as to match data
with a particular crash record in an aggregate database,
provided confidentiality of personal data is thereafter
preserved

2. Used in defense of litigation involving a
DaimlerChrysler Corporation product

3. Requested by police under a legal warrant

4. Otherwise required by law

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69

Data Parameters that May Be Recorded:

•

Diagnostic trouble code(s) and warning light status for
electronically controlled safety systems, including the
airbag system

•

Airbag disable light status (if equipped)

•

9Time9 of airbag deployment (in terms of ignition
cycles and vehicle mileage)

•

Airbag deployment level (if applicable)

•

Impact acceleration and angle

•

Seat belt status

•

Brake status (service and parking brakes)

•

Accelerator status (including vehicle speed)

•

Engine control status (including engine speed)

•

Transmission gear selection

•

Cruise control status

•

Traction/stability control status

•

Tire pressure monitoring system status

Child Restraint

Everyone in your vehicle needs to be buckled up all the
time — babies and children, too. Every state in the United
States and all Canadian provinces require that small
children ride in proper restraint systems. This is the law,
and you can be prosecuted for ignoring it.

Children 12 years and under should ride properly buck­led up in a rear seat, if available. According to crash
statistics, children are safer when properly restrained in
the rear seats rather than in the front.

2

70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

In a collision, an unrestrained child, even a tiny baby,
can become a missile inside the vehicle. The force
required to hold even an infant on your lap can
become so great that you could not hold the child, no
matter how strong you are. The child and others
could be badly injured. Any child riding in your
vehicle should be in a proper restraint for the child’s
size.

There are different sizes and types of restraints for
children from newborn size to the child almost large
enough for an adult safety belt. Always check the child
seat Owner’s Manual to ensure you have the right seat
for your child. Use the restraint that is correct for your
child:

Infants and Child Restraints

Safety experts recommend that children ride

•

rearward-facing in the vehicle until they are at least
one year old and weigh at least 20 lbs (9 kg). Two types
of child restraints can be used rearward-facing: infant
carriers and “convertible” child seats.

•

The infant carrier is only used rearward-facing in the
vehicle. It is recommended for children who weigh up
to about 20 lbs (9 kg). “Convertible” child seats can be
used either rearward-facing or forward-facing in the
vehicle. Convertible child seats often have a higher
weight limit in the rearward-facing direction than
infant carriers do, so they can be used rearward-facing
by children who weigh more than 20 lbs (9 kg) but are
less than one year old. Both types of child restraints are
held in the vehicle by the lap/shoulder belt or the
LATCH child restraint anchorage system. Refer to

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71

“LATCH — Child Seat Anchorage System (Lower
Anchors and Tether for CHildren)” in this section.

•

Rearward-facing child seats must NEVER be used in
the front seat of a vehicle with the front passenger
airbag unless the airbag is turned off. An airbag
deployment could cause severe injury or death to
infants in this position.

Older Children and Child Restraints

Children who weigh more than 20 lbs (9 kg) and who are
older than one year can ride forward-facing in the
vehicle. Forward-facing child seats and convertible child
seats used in the forward-facing direction are for children
who weigh 20 to 40 lbs (9 to 18 kg) and who are older
than one year. These child seats are also held in the
vehicle by the lap/shoulder belt or the LATCH child
restraint anchorage system. Refer to “LATCH — Child
Seat Anchorage System (Lower Anchors and Tether for
CHildren)” in this section.

The belt-positioning booster seat is for children weighing
more than 40 lbs (18 kg), but who are still too small to fit
the vehicle’s seat belts properly. If the child cannot sit
with knees bent over the vehicle’s seat cushion while the
child’s back is against the seat back, they should use a
belt-positioning booster seat. The child and belt­positioning booster seat are held in the vehicle by the
lap/shoulder belt.

Children Too Large for Booster Seats

Children who are large enough to wear the shoulder belt
comfortably, and whose legs are long enough to bend
over the front of the seat when their back is against the
seat back, should use the lap/shoulder belt in a rear seat.

•

Make sure that the child is upright in the seat.

•

The lap portion should be low on the hips and as snug
as possible.

2

72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

•

Check belt fit periodically. A child’s squirming or
slouching can move the belt out of position.

•

If the shoulder belt contacts the face or neck, move the
child closer to the center of the vehicle. Never allow a
child to put the shoulder belt under an arm or behind
their back.

NOTE: For additional information, refer to
www.seatcheck.org or call 1–866–SEATCHECK.

WARNING!

•

Improper installation can lead to failure of an
infant or child restraint. It could come loose in a
collision. The child could be badly injured or
killed. Follow the manufacturer’s directions ex­actly when installing an infant or child restraint.

•

A rearward facing infant restraint should only be
used in a rear seat. A rearward facing infant
restraint in the front seat may be struck by a
deploying passenger airbag, which may cause se­vere or fatal injury to the infant.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73

Here are some tips on getting the most out of your child
restraint:

•

Before buying any restraint system, make sure that it
has a label certifying that it meets all applicable Safety
Standards. The manufacturer also recommends that
you try a child restraint in the vehicle seats where you
will use it before you buy it.

•

The restraint must be appropriate for your child’s
weight and height. Check the label on the restraint for
weight and height limits.

•

Carefully follow the instructions that come with the
restraint. If you install the restraint improperly, it may
not work when you need it.

•

Buckle the child into the restraint exactly as the
manufacturer’s instructions tell you.

•

When your child restraint is not in use, secure it in the
vehicle with the seat belt or remove it from the vehicle.

Do not leave it loose in the vehicle. In a sudden stop or
collision, it could strike the occupants or seat backs
and cause serious personal injury.

LATCH — Child Seat Anchorage System (Lower
Anchors and Tether for CHildren)

Your vehicle’s rear seat is equipped with the child
restraint anchorage system called LATCH. The LATCH
system provides for the installation of the child restraint
without using the vehicle’s seat belts, instead securing
the child restraint using lower anchorages and upper
tether straps from the child restraint to the vehicle
structure.

LATCH-compatible child restraint systems are now avail­able. However, because the lower anchorages are to be
introduced over a period of years, child restraint systems
having attachments for those anchorages will continue to
have features for installation using the vehicle’s seat
belts. Child restraints having tether straps and hooks for

2

74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

connection to the top tether anchorages have been avail­able for some time. For some older child restraints, many
child restraint manufacturers offer add-on tether strap
kits or retrofit kits. You are urged to take advantage of all
the available attachments provided with your child re­straint in any vehicle.

The two outboard rear-seating positions have lower
anchorages that are capable of accommodating LATCH­compatible child seats having flexible, webbing-mounted
lower attachments. Child seats with fixed lower attach­ments must be installed in the outboard positions only.
Regardless of the specific type of lower attachment.
NEVER install LATCH-compatible child seats such that
two seats share a common lower anchorage.

If you are installing LATCH-compatible child restraints
in adjacent rear seating positions, you can use the
LATCH anchors or the vehicle’s seat belt for the outboard
position, but you must use the vehicle’s seat belt at the
center position. If your child restraints are not LATCH­compatible, you can only install the child restraints using
the vehicle’s seat belts. Please refer to “Installing the
LATCH-Compatible Child Restraint System” and “In­stalling Child Restraints Using the Vehicle Seat Belt” in
this section for typical installation instructions.

Installing the LATCH-Compatible Child Restraint
System

We urge that you carefully follow the directions of the
manufacturer when installing your child restraint. Not all
child restraint systems will be installed as described here.
Again, carefully follow the installation instructions that
were provided with the child restraint system.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75

The rear seat lower anchorages are round bars, located at
the rear of the seat cushion where it meets the seat back,
and are just visible when you lean into the rear seat to
install the child restraint. You will easily feel them if you
run your finger along the intersection of the seatback and
seat cushion surfaces.

Latch Anchorages

In addition, there are tether strap anchorages behind each
rear seating position located on the back of the seat.

2

Tether Strap Mounting

Many, but not all restraint systems will be equipped with
separate straps on each side, with each having a hook or
connector for attachment to the lower anchorage and a

76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

means of adjusting the tension in the strap. Forward­facing toddler restraints and some rear-facing infant
restraints will also be equipped with a tether strap, a
hook for attachment to the tether strap anchorage and a
means of adjusting the tension of the strap.

You will first loosen the adjusters on the lower straps and
on the tether strap so that you can more easily attach the
hooks or connectors to the vehicle anchorages. Next,
attach the lower hooks or connectors over the top of the
anchorage bars, pushing aside the seat cover material.
Then, locate the tether anchorage directly behind the seat
where you are placing the child restraint and attach the
tether strap to the anchorage, being careful to route the
tether strap to provide the most direct path between the
anchor and the child restraint. Finally, tighten all three
straps as you push the child restraint rearward and
downward into the seat, removing slack in the straps
according to the child restraint manufacturer’s instruc­tions.

WARNING!

Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.

Installing Child Restraints Using the Vehicle Seat
Belt

The passenger seat belts are equipped with either cinch­ing latch plates or automatic locking retractors, which are
designed to keep the lap portion tight around the child
restraint so that it is not necessary to use a locking clip. If
the seat belt has a cinching latch plate, pulling up on the
shoulder portion of the lap/shoulder belt will tighten the

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77

belt. However, any seat belt system may loosen with
time, so check the belt occasionally, and pull it tight if
necessary.

If the seat belt has an automatic locking retractor, pull the
belt from the retractor until there is enough to allow you
to pass through the child restraint and slide the latch
plate into the buckle. Then, pull the belt until it is all
extracted from the retractor. Allow the belt to return to
the retractor, pulling on the excess webbing to tighten the
lap portion about the child restraint. Refer to “Automatic
Locking Mode” earlier in this section.

In the rear seat, you may have trouble tightening the
lap/shoulder belt on the child restraint because the
buckle or latch plate is too close to the belt path opening
on the restraint. Disconnect the latch plate from the
buckle and twist the short buckle-end belt several times
to shorten it. Insert the latch plate into the buckle with the
release button facing out.

If the belt still can’t be tightened, or if by pulling and
pushing on the restraint loosens the belt, you may need
to do something more. Disconnect the latch plate from
the buckle, turn the buckle around, and insert the latch
plate into the buckle again. If you still can’t make the
child restraint secure, try a different seating position.

2

78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To attach a child restraint tether strap:
Route the tether strap over the seat back and attach the

hook to the tether anchor located on the back of the seat.
For the outboard seating positions, route the tether
underneath the headrest and attach the hook to the tether
anchor located on the back of the seat.

Tether Strap Mounting

WARNING!

An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchor positions directly behind
the child seat to secure a child restraint top tether
strap.

Transporting Pets

Airbags deploying in the front seat could harm your pet.
An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in
a collision.

Pets should be restrained in the rear seat in pet harnesses
or pet carriers that are secured by seat belts.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79

ENGINE BREAK-IN RECOMMENDATIONS

A long break-in period is not required for the engine in
your new vehicle.

Drive moderately during the first 300 miles (500 km).
After the initial 60 miles (100 km), speeds up to 50 or 55
mph (80 or 90 km/h) are desirable.

While cruising, brief full-throttle acceleration, within the
limits of local traffic laws, contributes to a good break-in.
Wide-open throttle acceleration in low gear can be detri­mental and should be avoided.

The engine oil installed in the engine at the factory is a
high quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur.
The recommended viscosity and quality grades are
shown in Section 7 of this manual. NON-DETERGENT
OR STRAIGHT MINERAL OILS MUST NEVER BE
USED.

A new engine may consume some oil during its first few
thousand miles (kilometers) of operation. This should be
considered as a normal part of the break-in and not
interpreted as an indication of difficulty.

SAFETY TIPS
Transporting Passengers

NEVER TRANSPORT PASSENGERS IN THE CARGO
AREA.

2

80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously
injured or killed.

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat belts.

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Lock Your Vehicle

Always remove the keys from the ignition and lock all
doors when leaving the vehicle unattended, even in your
own driveway or garage. Try to park your vehicle in a
well-lit area and never invite theft by leaving articles of
value exposed.

Exhaust Gas

Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in or
out of the area.

If it is necessary to sit in a parked vehicle with the engine
running, adjust your heating or cooling controls to force
outside air into the vehicle. Set the blower at high speed.

The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.

Whenever a change is noticed in the sound of the exhaust
system, when exhaust fumes can be detected inside the
vehicle, or when the underside or rear of the vehicle is
damaged, have a competent mechanic inspect the com­plete exhaust system and adjacent body areas for broken,
damaged, deteriorated, or mispositioned parts. Open
seams or loose connections could permit exhaust fumes
to seep into the passenger compartment. In addition,

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81

inspect the exhaust system each time the vehicle is raised
for lubrication or oil change. Replace as required.

WARNING!

•

Exhaust gases can injure or kill. They contain
carbon monoxide (CO) which is colorless and
odorless. Breathing it can make you unconscious
and can eventually poison you. To avoid breathing
(CO) follow the safety tips below.

•

If you are required to drive with the trunk open,
make sure that all windows are closed, and the
climate control blower switch is set at high speed.
DO NOT use the recirculation mode.

Safety Checks You Should Make Inside The Vehicle

Seat Belts

Inspect the belt system periodically, checking for cuts,
frays, and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.

Front seat belt assemblies must be replaced after a
collision. Rear seat belt assemblies must be replaced after
a collision if they have been damaged (bent retractor,torn
webbing, etc. If there is any question regarding belt or
retractor condition, replace the belt.

Airbag Warning Light

The light should come on and remain on for 6 to 8
seconds as a bulb check when the ignition switch is first
turned ON. If the light is not lit during starting, see you
authorized dealer. If the light stays on, flickers, or comes
on while driving, have the system checked by an autho­rized dealer.

2

82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Defroster

Check operation by selecting the defrost mode and place
the blower control on high speed. You should be able to
feel the air directed against the windshield. See your
authorized dealer for service if your defroster is inoper­able.

Periodic Safety Checks You Should Make Outside The Vehicle

Tires

Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread. Inspect the tread and sidewall for
cuts and cracks. Check the wheel nuts for tightness.
Check the tires (including spare) for proper pressure.

Lights

Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.

Door Latches

Check for positive closing, latching, and locking.

Fluid Leaks

Check area under vehicle after overnight parking for fuel,
engine coolant, oil, or other fluid leaks. Also, if gasoline
fumes are detected or if fuel, power steering fluid, or
brake fluid leaks are suspected, the cause should be
located and corrected immediately.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CONTENTS

m Mirrors ...............................88

▫ Inside Day/Night Mirror .................88

▫ Automatic Dimming Mirror — If Equipped ....88

▫ Outside Mirrors .......................89

▫ Exterior Mirrors Folding Feature —

If Equipped ..........................90

m Hands–Free Communication (UConnectt)—

If Equipped ............................92

▫ Operation ............................94

▫ Phone Call Features ...................101

▫ UConnectt System Features ..............104

▫ Advanced Phone Connectivity ............108

3

▫ Power Remote Control Mirrors .............90

▫ Heated Remote Control Mirrors —

If Equipped ..........................91

▫ Illuminated Vanity Mirrors — If Equipped ....91

▫ Things You Should Know About Your

UConnectt System ....................110

▫ General Information ...................118

84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

m Seats ................................118

▫ Manual Front Seat Adjustments ...........118

▫ Power Seat — If Equipped ...............121

▫ Head Restraints ......................122

▫ Heated Seats — If Equipped .............123

▫ 60/40 Split Folding Rear Seat With Fold Flat

Feature ............................124

m Driver Memory Seat — If Equipped .........127

▫ Programming The Memory Feature ........127

▫ Linking & Unlinking The Remote Keyless

(RKE) Transmitter To The Memory Feature . . .128

▫ Memory Position Recall .................129

▫ Easy Entry/Exit Seat (Available With Memory

Seat Only) ..........................129

m To Open And Close The Hood .............131

m Lights ...............................133

▫ Exterior & Interior Lighting Control ........133

▫ Headlights & Parking Lights .............133

▫ Automatic Headlights — If Equipped .......134

▫ Headlights With Wipers (Available With Auto

Headlights Only) .....................134

▫ Headlight Time Delay — If Equipped .......134

▫ Daytime Running Lights (DRL) —

If Equipped .........................135

▫ Lights-On Reminder ...................135

▫ Fog Lights — If Equipped ...............136

▫ Turn Signals .........................136

▫ Highbeam/Lowbeam Select Switch .........137

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85

▫ Flash To Pass ........................137

▫ Interior Lights .......................138

m Windshield Wipers And Washers ............140

▫ Intermittent Wiper System ...............141

▫ Mist Feature .........................142

▫ Headlights With Wipers (Available With Auto

Headlights Only) .....................143

▫ Rain Sensing Wipers — If Equipped ........143

▫ Windshield Washers ...................145

▫ Adding Washer Fluid ..................145

m Tilt Steering Column ....................146

m Electronic Speed Control — If Equipped ......147

▫ Electronic Speed Control Operation ........147

▫ To Activate ..........................147

▫ To Set At A Desired Speed ...............148

▫ To Deactivate ........................148

▫ To Resume Speed .....................149

▫ To Vary The Speed Setting ...............149

▫ To Accelerate For Passing ...............149

m Rear Park Assist System — If Equipped .......150

▫ System Usage Precautions ...............150

▫ Enabling & Disabling The System ..........152

▫ System Operation .....................153

m Garage Door Opener — If Equipped .........155

▫ Programming HomeLinkt ...............156

▫ Gate Operator/Canadian Programming .....159

3

86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫ Using HomeLinkt .....................159

▫ Reprogramming a Single HomeLinkt

Button .............................160

▫ Security ............................160

▫ Troubleshooting Tips ...................160

▫ General Information ...................161

m Power Sunroof — If Equipped .............161

▫ Opening Sunroof - Express ..............162

▫ Closing Sunroof - Express ...............162

▫ Pinch Protect Feature ...................162

▫ Pinch Protect Override .................163

▫ Venting Sunroof - Express ...............163

▫ Sunshade Operation ...................163

▫ Wind Buffeting .......................163

▫ Sunroof Maintenance ...................164

▫ Ignition Off Operation ..................164

m Sky Slidert Full Length Open Roof ..........164

▫ Sky Slidert Usage Precautions ............164

▫ Power Top Control ....................166

▫ Opening The Sky Slidert ................166

▫ Closing The Sky Slidert .................167

▫ Anti-Pinch Protect Feature ...............168

▫ Wind Buffeting .......................168

▫ Sky Slidert Maintenance ................169

m Electrical Power Outlet ...................169

▫ Electrical Outlet Use With Engine Off .......170

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

m Power Inverter — If Equipped .............170

m Cup Holders ..........................172

m Storage ..............................173

▫ Front Storage Compartment ..............173

▫ Console Storage Compartment ............173

m Cargo Area Features .....................174

▫ Cargo Load Floor .....................174

m Rear Window Features ...................180

▫ Rear Window Wiper/Washer — If Equipped . .180

▫ Rear Window Defroster — If Equipped ......181

m Roof Luggage Rack — If Equipped ..........182

3

88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

MIRRORS
Inside Day/Night Mirror

Adjust the mirror to center on the view through the rear
window. A two-point pivot system allows for horizontal
and vertical mirror adjustment.

Manual Rearview Mirror

Annoying headlight glare can be reduced by moving the
small control under the mirror to the night position
(toward rear of vehicle). The mirror should be adjusted
while set in the day position (toward windshield).

Automatic Dimming Mirror — If Equipped

This mirror automatically adjusts for annoying headlight
glare from vehicles behind you. You can turn the feature
on or off by pressing the button at the base of the mirror.
A light in the button will indicate when the dimming
feature is activated.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89

Outside Mirrors

To receive maximum benefit, adjust the outside mirror(s)
to center on the adjacent lane of traffic and a slight
overlap of the view obtained from the inside mirror.

Automatic Dimming Mirror

CAUTION!

To avoid damage to the mirror during cleaning, never
spray any cleaning solution directly onto the mirror.
Apply the solution onto a clean cloth and wipe the
mirror clean.

NOTE: The passenger side convex outside mirror will

give a much wider view to the rear, and especially of the
lane next to your vehicle.

WARNING!

Vehicles and other objects seen in the passenger side
convex mirror will look smaller and farther away
than they really are. Relying too much on your
passenger side convex mirror could cause you to
collide with another vehicle or other object. Use your
inside mirror when judging the size or distance of a
vehicle seen in the passenger side convex mirror.

3

90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Exterior Mirrors Folding Feature — If Equipped

Some models have exterior mirrors that are hinged. The
hinge allows the mirror to pivot forward and rearward to
resist damage. The hinge has three detent positions,
forward, rearward, and normal.

Power Remote Control Mirrors

The power mirror switch is located on driver’s door trim
panel.

Power Mirror Switches

Models without Express Window Feature

Press the mirror select button marked L or R and then
press one of the four arrow buttons to move the mirror in
the direction the arrow is pointing.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

Models with Express Window Feature

Press and release the mirror select button marked L or R
and then press one of the four arrow buttons to move the
mirror in the direction the arrow is pointing. The selec­tion will time out after 30 seconds of inactivity to guard
against accidentally moving a mirror position following
an adjustment.

NOTE: For vehicles equipped with Driver Memory
Seat, you can use your Remote Keyless Entry (RKE)
transmitter or the memory switch on the instrument
panel to return the power mirrors to pre-programmed
positions. Refer to “Driver Memory Seat” in this section
for details.

Heated Remote Control Mirrors — If Equipped

These mirrors are heated to melt frost or ice. This feature
is activated whenever you turn on the Rear Window
Defrost.

Illuminated Vanity Mirrors — If Equipped

An illuminated vanity mirror is on each sun visor. To use
the mirror, rotate the sun visor down and swing the
mirror cover upward. The lights will turn on automati­cally. Closing the mirror cover will turn off the light.

3

Illuminated Vanity Mirror

92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Sun Visor “Slide-Out” Feature — If Equipped

The sun visor “slide-on rod” feature allows for additional
flexibility in positioning the visor to block out the sun.

1. Fold down sun visor.

2. Unclip visor from center clip.

3. Pull the sun visor toward inside rearview mirror to
extend.

HANDS–FREE COMMUNICATION (UConnectT)—
IF EQUIPPED

NOTE: The sales code RER radio contains an inte­grated Hands-Free Communication (UConnectt) sys­tem. Refer to your “Navigation User’s Manual” for
UConnectt system operating instructions for this radio.

UConnectt is a voice-activated, hands-free, in- vehicle
communications system. UConnectt allows you to dial a
phone number with your cellular phone using simple

voice commands (e.g., 9Call” { “Mike” {”Work9 or 9Dial”
{ “248-555-12129). Your cellular phone’s audio is trans­mitted through your vehicle’s audio system; the system
will automatically mute your radio when using the
UConnectt system.

NOTE: The UConnectt system use requires a cellular
phone equipped with the Bluetooth 9Hands-Free Profile,9
version 0.96 or higher. See UConnectt website for sup­ported phones.

NOTE: For UConnectt customer support, visit the
following web sites:

•

www.chrysler.com/uconnect

•

www.dodge.com/uconnect

•

www.jeep.com/uconnect

•

or call 1–877–855–8400

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93

UConnectt allows you to transfer calls between the
system and your cellular phone as you enter or exit your
vehicle, and enables you to mute the system’s micro­phone for private conversation.

The UConnectt phone book enables you to store up to 32
names and four numbers per name. Each language has a
separate 32-name phone book accessible only in that
language. This system is driven through your Blue­tooth™ Hands-Free profile cellular phone. UConnectt
features Bluetooth™ technology - the global standard
that enables different electronic devices to connect to
each other without wires or a docking station, so UCon­nectt works no matter where you stow your cellular
phone (be it your purse, pocket, or briefcase), as long as
your phone is turned on and has been paired to the
vehicle’s UConnectt system. The UConnectt system
allows up to seven cellular phones to be linked to system.
Only one linked (or paired) cellular phone can be used

with the system at a time. The system is available in
English, Spanish, or French languages (as equipped).

Phone Button

The rearview mirror contains the microphone
for the system (depending on the type of
mirror and radio equipped), and either the
radio or the mirror has the two control buttons
(Phone Button and Voice Recognition Button)
that will enable you to access the system.

Voice Recognition Button

Actual button location may vary with radio.
The individual buttons are described in the
“Operation” section.

The UConnectt system can be used with any Hands-Free
Profile certified Bluetooth™ cellular phone. See UCon­nectt website for supported phones. If your cellular
phone supports a different profile (e.g., Headset Profile)

3

94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

you may not be able to use any UConnectt features.
Refer to your cellular service provider or the phone
manufacturer for details.

The UConnectt system is fully integrated with the vehi­cle’s audio system. The volume of the UConnectt system
can be adjusted either from the radio volume control
knob or from the steering wheel radio control (right
switch), if so equipped.

The radio display will be used for visual prompts from
the UConnectt system such as 9CELL9 or caller ID on
certain radios.

Operation

Voice commands can be used to operate the UConnectt
system and to navigate through the UConnectt menu
structure. Voice commands are required after most
UConnectt system prompts. You will be prompted for a
specific command and then guided through the available
options.

•

Prior to giving a voice command, one must wait for
the beep, which follows the 9Ready9 promptor another
prompt.

•

For certain operations, compound commands can be
used. For example, instead of saying 9Setup9 and then
9Phone Pairing,9 the following compound command
can be said: 9Setup Phone Pairing.9

•

For each feature explanation in this section, only the
combined form of the voice command is given. You
can also break the commands into parts and say each
part of the command, when you are asked for it. For
example, you can use the combined form voice com­mand 9Phonebook New Entry,9 or you can break the
combined form command into two voice commands:
9Phonebook9 and 9New Entry.9 Please remember, the
UConnectt system works best when you talk in a
normal conversational tone, as if speaking to some one
sitting eight feet away from you.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95

Voice Command Tree

Refer to “Voice Tree” at the end of this section.

Help Command

If you need assistance at any prompt, or if you want to
know your options at any prompt, say 9Help9 following
the beep. The UConnectt system will play all the options
at any prompt if you ask for help.

To activate the UConnectt system from idle, simply press
the “Phone” button and follow audible prompts for
directions. All UConnectt system sessions begin with a
press of the “Phone” button on the radio control head.

Cancel Command

At any prompt, after the beep, you can say 9Cancel9 and
you will be returned to the main menu. However, in a
few instances the system will take you back to the
previous menu.

Pair (Link) UConnectt System to a Cellular Phone

To begin using your UConnectt system, you must pair
your compatible Bluetooth™ enabled cellular phone.

To complete the pairing process, you will need to refer­ence your cellular phone owner’s manual. The UCon­nectt website may also provide detailed instructions for
pairing.

The following are general phone to UConnectt System
pairing instructions:

•

Press the “Phone” button to begin.

•

After the 9Ready9 prompt and the following beep, say
9Setup Phone Pairing.9

•

When prompted, after the beep, say 9Pair a Phone9 and
follow the audible prompts.

•

You will be asked to say a four-digit pin number,
which you will later need to enter into your cellular.

3

96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

You can enter any four-digit pin number. You will not
need to remember this pin number after the initial
pairing process.

•

For identification purposes, you will be prompted to
give the UConnectt system a name for your cellular
phone. Each cellular phone that is paired should be
given a unique phone name.

•

You will then be asked to give your cellular phone a
priority level between 1 and 7, 1 being the highest
priority. You can pair up to seven cellular phones to
your UConnectt system. However, at any given time,
only one cellular phone can be in use, connected to
your UConnectt System. The priority allows the
UConnectt system to know which cellular phone to
use if multiple cellular phones are in the vehicle at the
same time. For example, if priority 3 and priority 5
phones are present in the vehicle, the UConnectt
system will use the priority 3 cellular phone when you

make a call. You can select to use a lower priority
cellular phone at any time (refer to 9Advanced Phone
Connectivity9).

Dial by Saying a Number

Press the “Phone” button to begin.

•

•

After the 9Ready9 prompt and the following beep, say
9Dial.9

•

System will prompt you to say the number you want
call.

•

For example, you can say 9234-567-8901.9 The phone
number that you enter must be of valid length and
combination. Based on the country in which the ve­hicle was purchased, the UConnectt limits the user
from dialing invalid combination of numbers. For
example, in USA, 234-567-890 is nine digits long,
which is not a valid USA phone number - the closest
valid phone number has ten digits.

•

The UConnectt system will confirm the phone num­ber and then dial. The number will appear in the
display of certain radios.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

•

The UConnectt system will confirm the name and
then dial the corresponding phone number, which
may appear in the display of certain radios.

Call by Saying a Name

Press the “Phone” button to begin.

•

•

After the 9Ready9 prompt and the following beep, say
“Call.9

•

System will prompt you to say the name of the person
you want call.

•

After the 9Ready9 prompt and the following beep, say
the name of the person you want to call. For example,
you can say 9John Doe,9 where John Doe is a previ­ously stored name entry in the UConnectt phone
book. Refer to 9Add Names to Your UConnectt Phone­book,9 to learn how to store a name in the phone book.

Add Names to Your UConnectt Phonebook
NOTE: Adding names to phone book is recommended

when vehicle is not in motion.

•

Press the “Phone” button to begin.

•

After the 9Ready9 prompt and the following beep, say
9Phonebook New Entry.9

•

When prompted, say the name of the new entry. Use of
long names helps the voice recognition and it is
recommended. For example, say 9Robert Smith9 or
9Robert9 instead of 9Bob.9

•

When prompted, enter the number designation (e.g.,
9Home,99Work,99Mobile,9 or 9Pager9). This will allow
you to store multiple numbers for each phone book
entry, if desired.

3

98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

•

When prompted, recite the phone number for the
phone book entry that you are adding.

After you are finished adding an entry into the phone
book, you will be given the opportunity to add more
phone numbers to the current entry or to return to the
main menu.

The UConnectt system will allow you to enter up to 32
names in the phone book with each name having up to
four associated phone numbers and designations. Each
language has a separate 32-name phone book accessible
only in that language.

Phonebook Download

UConnectt allows the user to download entries from
their phone via Bluetooth. To use this feature, press the
“Phone” button and say “Phonebook Download.” Sys­tem prompts “Ready to accept vcard entry via Blue­tooth…” The system is now ready to accept phonebook
entries from your phone using the Bluetooth Object

Exchange Profile (OBEX). Please see your phone owners’
manual for specific instructions on how to send these
entries from your phone.

NOTE:

•

Phone handset must support Bluetooth OBEX trans­fers of phonebook entries to use this feature.

•

Some phones cannot send phonebook entries if they
are already connected to any system via Bluetooth,
and you may see a message on the phone display that
the Bluetooth link is busy. In this case, the user must
first disconnect or drop the Bluetooth connection to
the UConnectt and then send the address book entry
via Bluetooth. Please see your phone owners’ manual
for specific instructions on how to drop the Bluetooth
connection.

•

If the phonebook entry is longer than 24 characters it
will be use only the first 24 characters.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99

Edit Entries in the UConnectt Phonebook
NOTE: Editing names in the phone book is recom-

mended when vehicle is not in motion.

•

Press the “Phone” button to begin.

•

After the 9Ready9 prompt and the following beep, say
9Phonebook Edit.9

•

You will then be asked for the name of the phone book
entry that you wish to edit.

•

Next, choose the number designation (home, work,
mobile, or pager) that you wish to edit.

•

When prompted, recite the new phone number for the
phone book entry that you are editing.

After you are finished editing an entry in the phone book,
you will be given the opportunities to edit another entry
in the phonebook, call the number you just edited, or
return to the main menu.

9Phonebook Edit9 can be used to add another phone
number to a name entry that already exists in the
phonebook. For example, the entry John Doe may have a
mobile and a home number, but you can add John Doe’s
work number later using the 9Phonebook Edit9 feature.

Delete Entries in the UConnectt Phonebook
NOTE: Editing phone book entries is recommended

when vehicle is not in motion.

•

Press the “Phone” button to begin.

•

After the 9Ready9 prompt and the following beep, say
9Phonebook Delete.9

•

After you enter the Phonebook Delete menu, you will
then be asked for the name of the entry that you wish
to delete. You can either say the name of a phone book
entry that you wish to delete or you can say 9List
Names9 to hear a list of the entries in the phone book
from which you choose. To select one of the entries

3

100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

from the list, press the 9Voice Recognition9 button
while the UConnectt system is playing the desired
entry and say 9Delete.9

•

After you enter the name, the UConnectt system will
ask you which designation you wish to delete, home,
work, mobile, pager, or all. Say the designation you
wish to delete.

•

Note that only the phone book entry in the current
language is deleted.

Delete All Entries in the UConnectt Phonebook

Press the “Phone” button to begin.

•

•

After the 9Ready9 prompt and the following beep, say
9Phonebook Erase All.9

•

The UConnectt system will ask you to verify that you
wish to delete all the entries from the phonebook.

•

After confirmation, the phone book entries will be
deleted.

•

Note that only the phone book in the current language
is deleted.

List All Names in the UConnectt Phonebook

•

Press the “Phone” button to begin.

•

After the 9Ready9 prompt and the following beep, say
9Phonebook List Names.9

•

The UConnectt system will play the names of all the
phone book entries.

•

To call one of the names in the list, press the 9Voice
Recognition’ button during the playing of the desired
name, and say 9Call.9

NOTE: The user can also exercise 9Edit9 or 9Delete9
operations at this point.