jcb JCB-CD20LI2 Operating Manual

Positec Australia Pty Limited
Unit 15, 23 Narabang Way, Belrose 2085 NSW Australia
www.jcb-tools.com
Customer Helpline 1300 889 028

Safety and operating manual

20V Std Combi Drill
JCB-CD20LI2

Positec Australia Pty Limited
Unit 15, 23 Narabang Way, Belrose 2085 NSW Australia
www.jcb-tools.com
Customer Helpline 1300 889 028

WARNING! Read all
safety warnings and all

instructions.

Failure to follow the
warnings and instructions may
result in electric shock, fire and/or
serious injury.

Save all warnings and instructions
for future reference.

The term “power tool” in the
warnings refers to your mains­operated (corded) power tool or
battery-operated (cordless) power
tool.

1. Work area safety

a) Keep work area clean and well
lit.

Cluttered or dark areas invite

accidents.

b) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust.

Power tools create
sparks which may ignite the dust
or fumes.

c) Keep children and bystanders
away while operating a power tool.

Distractions can cause you to
lose control.

2. Electrical safety

a) Power tool plugs must match
the outlet. Never modify the plug
in any way. Do not use any adapter
plugs with earthed (grounded)
power tools.

Unmodified plugs

and matching outlets will reduce
risk of electric shock.

b) Avoid body contact with
earthed or grounded surfaces,
such as pipes, radiators, ranges
and refrigerators.

There is an
increased risk of electric shock if
your body is earthed or grounded.

c) Do not expose power tools
to rain or wet conditions.

Water
entering a power tool will increase
the risk of electric shock.

d) Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.

Damaged or entangled cords
increase the risk of electric shock.

e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use.

Use of
a cord suitable for outdoor use
reduces the risk of electric shock.

f) If operating a power tool in a
damp location is unavoidable, use
a residual current device (RCD)
protected supply.

Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence

GENERAL POWER TOOL SAFETY WARNINGS

ORIGINAL INSTRUCTIONS

Positec Australia Pty Limited
Unit 15, 23 Narabang Way, Belrose 2085 NSW Australia
www.jcb-tools.com
Customer Helpline 1300 889 028

of drugs, alcohol or medication.

A moment of inattention while
operating power tools may result
in serious personal injury.

b) Use personal protective
equipment. Always wear eye
protection.

Protective equipment
such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
injuries.

c) Prevent unintentional starting.
Ensure the switch is in the off­position before connecting to
power source and/or battery pack,
picking up or carrying the tool.

Carrying power tools with your
finger on the switch or energising
power tools that have the switch
on invites accidents.

d) Remove any adjusting key or
wrench before turning the power
tool on.

A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.

e) Do not overreach. Keep proper
footing and balance at all times.

This enables better control of
the power tool in unexpected
situations.

f) Dress properly. Do not wear
loose clothing or jewellery. Keep
your hair, clothing and gloves
away from moving parts.

Loose
clothes, jewellery or long hair can
be caught in moving parts.

g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.

Use of dust collection can reduce
dust-related hazards.

4. Power tool use and care

a) Do not force the power tool.
Use the correct power tool for
your application.

The correct
power tool will do the job better
and safer at the rate for which it
was designed.

b) Do not use the power tool if
the switch does not turn it on and
off.

Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.

c) Disconnect the plug from
the power source and/or the
battery pack from the power tool
before making any adjustments,
changing accessories, or storing
power tools.

Such preventive
safety measures reduce the
risk of starting the power tool
accidentally.

d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool.

Power
tools are dangerous in the hands
of untrained users.

e) Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts

Positec Australia Pty Limited
Unit 15, 23 Narabang Way, Belrose 2085 NSW Australia
www.jcb-tools.com
Customer Helpline 1300 889 028

and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use.

Many
accidents are caused by poorly
maintained power tools.

f) Keep cutting tools sharp and
clean.

Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier
to control.

g) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.

Use
of the power tool for operations
different from those intended
could result in a hazardous
situation.

5. Battery tool use and care

a) Recharge only with the charger
specified by the manufacturer.

A
charger that is suitable for one
type of battery pack may create
a risk of fire when used with
another battery pack.

b) Use power tools only with
specifically designated battery
packs.

Use of any other battery
packs may create a risk of injury
and fire.

c) When battery pack is not in
use, keep it away from other metal
objects, like paper clips, coins,
keys, nails, screws or other small
metal objects, that can make a

connection from one terminal
to another.

Shorting the battery
terminals together may cause
burns or a fire.

d) Under abusive conditions,
liquid may be ejected from the
battery; avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help.

Liquid ejected from the battery
may cause irritation or burns.

6. Service

a) Have your power tool serviced
by a qualified repair person using
only identical replacement parts.

This will ensure that the safety of
the power tool is maintained.

Additional safety points for
your battery operated drills
& impact drill

1. Wear ear protectors when impact
drilling. Exposure to noise can
cause hearing loss.

2. Use auxiliary handle(s), if
supplied with the tool. Loss of
control can cause personal injury.

3. Hold power tool by insulated
gripping surfaces, when
performing an operation where
the cutting accessory may contact
hidden wiring. Cutting accessory
contacting a "live" wire may make
exposed metal parts of the power
tool "live" and could give the
operator an electric shock.

Positec Australia Pty Limited
Unit 15, 23 Narabang Way, Belrose 2085 NSW Australia
www.jcb-tools.com
Customer Helpline 1300 889 028

4. Always wear safety goggles or
eye protection when using this
tool. Use a dust mask or respirator
for applications which generate
dust.

5. Secure the material being drilled.
Never hold it in your hand or
across legs. Unstable support can
cause the drill bit to bind causing
loss of control and injury.

6. Disconnect battery pack from
tool or place the switch in the
locked or off position before
making any assembly, adjustments
or changing accessories. Such
preventive safety measures
reduce the risk of starting the tool
accidentally.

7. Position yourself to avoid being
caught between the tool or side
handle and walls or post. Should
the bit become bound or jammed
in the work, the reaction torque of
the tool could crush your hand or
leg.

8. If the bit becomes bound in the
workpiece, release the trigger
immediately, reverse the direction
of rotation and slowly squeeze the
trigger to back out the bit. Be ready
for a strong reaction torque. The
drill body will tend to twist in the
opposite direction as the drill bit is
rotating.

9. Do not grasp the tool or place
your hands too close to the
spinning chuck or drill bit. Your
hand may be lacerated.

10. When installing a drill bit, insert
the shank of the bit well within the
jaws of the chuck. If the bit is not
inserted deep enough, the grip of
the jaws over the bit is reduced and
the loss of control is increased.

11. Do not use dull or damaged bits
and accessories. Dull or damaged
bits have a greater tendency to
bind in the workpiece.

12. When removing the bit from the
tool avoid contact with skin and
use proper protective gloves when
grasping the bit or accessory.
Accessories may be hot after
prolonged use.

13. Check to see that keys and
adjusting wrenches are removed
from the drill before switching the
tool “ON”. Keys or wrenches can
fly away at high velocity striking
you or bystander.

14. Do not run the dill while
carrying it at your side. A spinning
drill bit could become entangled
with clothing and injury may result.

15. Avoid bouncing and snagging
the wheels, discs or brushes
especially when working corners,
sharp edges, etc. This can cause
loss of control and kickback.

16. Position the tether clear of
rotating bit. Do not wrap the tether
around your arm or wrist. If you
lose control and have the tether
wrapped around your arm or wrist,
it may entrap you and cause injury.