jcb JCB-BC26 Safety And Operating Manual Original Instructions

Important! It is essential that you read the instructions in this manual before assembling,

maintaining and operating this machine.
Subject to technical modifications.

STRING TRIMMER / BRUSHCUTTER
JCB-BC26

Keep the instruction for future reference.

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS

JCB-BC26_960443002-01_Manual_final.indd A1JCB-BC26_960443002-01_Manual_final.indd A1 12/2/2010 5:37:40 PM12/2/2010 5:37:40 PM

GENERAL SAFETY RULES

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

INTENDED USE

This product should only be used outdoors in a well-ventilated area.
The product is intended for cutting long grass, weeds, brush and similar vegetation

at or about ground level. The cutting plane should be approximately parallel to the
ground surface. The product should not be used to cut or trim hedges, bushes or other
vegetation where the cutting plane is not parallel to the ground surface.

For safe operation, read and understand all instructions before using the trimmer /
brushcutter. Follow all safety instructions. Failure to follow all safety instructions listed
below can result in serious personal injury.

 Do not allow children or untrained individuals to use this unit.
 Never start or run the engine in a closed or poorly ventilated area; breathing

exhaust fumes can kill.

 Clear the work area before each use. Remove all objects such as rocks, broken

glass, nails, wire or string which can be thrown or become entangled in the string

head or blade.
 Wear full eye and hearing protection while operating this unit.
 Wear heavy long trousers, boots and gloves. Do not wear loose fitting clothing,

short trousers, jewellery of any kind or use with bare feet.
 Secure long hair so it is above shoulder level to prevent entanglement in any

moving parts.
 Keep all bystanders, children and pets at least 15 m away.
 Do not operate this unit when you are tired, ill or under the influence of alcohol,

drugs or medication.
 Do not operate in poor lighting.
 Keep firm footing and balance. Do not overreach. Overreaching can result in loss

of balance or exposure to hot surfaces.
 Keep all parts of your body away from any moving part.
 Do not touch area around the exhaust, silencer or engine of the trimmer / brushcutter,

these parts get hot during operation.
 Always stop the engine and remove the spark plug wire before making any

adjustments or repairs except for carburetor adjustments.
 Inspect the unit before each use for loose fasteners, fuel leaks, etc. Replace any

damaged parts before use.

JCB-BC26_960443002-01_Manual_final.indd A2JCB-BC26_960443002-01_Manual_final.indd A2 12/2/2010 5:37:58 PM12/2/2010 5:37:58 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

 The string head or blade will rotate during carburetor adjustments.
 It has been reported that vibrations from hand-held tools may contribute to a

condition called Raynaud’s Syndrome in certain individuals. Symptoms may include
tingling, numbness and blanching of the fingers, usually apparent upon exposure
to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and
work practices are all thought to contribute to the development of these symptoms.
It is presently unknown what, if any, vibrations or extent of exposure may contribute
to the condition. There are measures that can be taken by the operator to possibly
reduce the effects of vibration:

 Keep your body warm in cold weather. When operating the unit, wear gloves to

keep the hands and wrists warm. It is reported that cold weather is a major factor

contributing to Raynaud’s Syndrome.
 After each period of operation, exercise to increase blood circulation.
 Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use
and see your doctor about these symptoms.

 Keep the tool well maintained, fasteners tightened and worn parts replaced.
 Mix and store fuel in a container approved for fuel.
 Mix fuel outdoors where there are no sparks or flames. Wipe up any fuel spillage.

Move 9 m away from refueling site before starting engine.

 Stop the engine and allow to cool before refueling, performing adjustments or

maintenance or storing the unit.

 Allow the engine to cool; empty the fuel tank and secure the unit from moving

before transporting in a vehicle.

JCB-BC26_960443002-01_Manual_final.indd A3JCB-BC26_960443002-01_Manual_final.indd A3 12/2/2010 5:37:59 PM12/2/2010 5:37:59 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

FOR TRIMMER

 Replace string head if cracked, chipped or damaged in any way. Be sure the string

head or blade is properly installed and securely fastened. Failure to do so can
cause serious injury.

 Make sure all guards, straps, deflectors and handles are properly and securely

attached.

 Use only the manufacturer's replacement line in the cutting head. Do not use any

other cutting attachment.
 Never operate unit without the grass deflector in place and in good condition.
 Maintain a firm grip on both handles while trimming. Keep string head below waist

level. Never cut with the string head located more than 76 cm above the ground.

FOR BRUSHCUTTER AND BLADE

 After engine stops, keep rotating blade in heavy grass or pulpy weeds until it stops.
 Do not operate the brushcutter unless the blade guard is firmly secured in place

and in good condition.
 Use heavy gloves while installing or removing blades.
 Always stop the engine and remove the spark plug wire before attempting to

remove any obstruction caught or jammed in the blade or before removing and

installing the blade.
 Do not attempt to touch or stop the blade when it is rotating.
 A coasting blade can cause injury while it continues to spin after the engine is

stopped or throttle trigger released. Maintain proper control until the blade has

completely stopped rotating.
 Replace any blade that has been damaged. Always make sure blade is installed

correctly and securely fastened before each use. Failure to do so can cause serious

injury.
 Use only the manufacturer's replacement blade intended for use on this brushcutter.

Do not use any other blade.
 The blade is suited for cutting pulpy weeds and vines only. Do not use for any other

purpose. Never use the blade to cut woody brush.
 Exercise extreme caution when using the blade with this unit. Blade thrust

is the reaction that may occur when the spinning blade contacts anything

it cannot cut. This contact may cause the blade to stop for an instant, and

suddenly “thrust” the unit away from the object that was hit. This reaction

ADDITIONAL SAFETY RULES

JCB-BC26_960443002-01_Manual_final.indd A4JCB-BC26_960443002-01_Manual_final.indd A4 12/2/2010 5:37:59 PM12/2/2010 5:37:59 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

can be violent enough to cause the operator to lose control of the unit.
Blade thrust can occur without warning if the blade snags, stalls or
binds. This is more likely to occur in areas where it is difficult to see the
material being cut. For safety and ease of cutting, approach the weeds
being cut from the right to the left. In the event an
unexpected object or woody stock is encountered,

this could minimize the blade thrust reaction.
 Never cut any material over 13 mm in diameter.
 Always wear the shoulder strap when using the brushcutter and adjust to a

comfortable operating position. Maintain a firm grip on both handles while cutting

with a blade. Keep the blade away from the body and below waist level. Never use

the brushcutter with the blade located 76 cm or more above ground level.
 Cover the blade with the blade protector before storing the unit or during

transportation. Always remove the blade protector before using the unit.

If not removed, the blade protector could become a thrown object as the blade

begins to turn.

JCB-BC26_960443002-01_Manual_final.indd A5JCB-BC26_960443002-01_Manual_final.indd A5 12/2/2010 5:37:59 PM12/2/2010 5:37:59 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

Thank you for your purchase.
The trimmer / brushcutter has been engineered and manufactured to a high standard

for dependability , ease of operation and operator safety. Properly cared for, it will give
years of rugged, trouble-free performance.

Important: Some of the following symbols may be used on the tool. Please

learn the meaning. Proper interpretation of the symbols will allow better and safer
operation of the tool.

SYMBOLS

Indicates danger, warning or caution. It means “Attention! Your safety is
involved.”

Read the operation manual and follow all warnings and safety
instructions.

Wear eye and ear and head protection.

Keep all bystanders, especially children and pets, at least 15 m from the
operating area.

Danger of ricochet.

JCB blade is appropriate for this unit and is suited for cutting pulpy
weeds and vines.

Do not use with a toothed saw type blade.

Rotational direction and maximum speed of the shaft for the cutting
attachment.

Wear non-slip safety footwear.

Wear non-slip heavy-duty gloves.

JCB-BC26_960443002-01_Manual_final.indd A6JCB-BC26_960443002-01_Manual_final.indd A6 12/2/2010 5:37:59 PM12/2/2010 5:37:59 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

Do not smoke when mixing fuel or filling fuel tank.

Use unleaded petrol intended for motor vehicle use with an octane rating
of 91 ([R+M]/2) or higher.

Use 2-stroke oil for air cooled engines.

Mix the fuel mixture thoroughly each time before fueling or refueling.

On/Off Switch (I = on; O = off)

Conforms with all regulatory standards in the EU country where the
product is purchased.

JCB-BC26_960443002-01_Manual_final.indd A7JCB-BC26_960443002-01_Manual_final.indd A7 12/2/2010 5:38:00 PM12/2/2010 5:38:00 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com

TECHNICAL DATA

SPECIFICATIONS

Weight (kg)

 Without fuel, cutting attachment and guard
 Without fuel; with string head
 Without fuel; with blade

4.56

5.20

5.11

Fuel tank volume [cm

3

or (L)] 250 or (0.25)

Cutting swath (mm)

 String head
 Blade

457

256
Recommended torque for blade (Nm) 11
Engine displacement (cm

3

/cc) 26
Line diameter (mm) 2.4
Maximum engine performance (in accordance with ISO

8893) (kW)

0.65

Maximum rotational frequency of spindle (min

-1

) 10,000

Engine speed (rotational frequency) at recommended
maximum spindle (min

-1

)

12,000

Engine speed (rotational frequency) at idle (min

-1

) 2,800-3,800

Fuel consumption (in accordance with ISO 8893) at maximum
engine performance [kg/h or (L/h)]

0.33 or (0.45)

Specifi c fuel consumption (in accordance with ISO 8893) at
maximum engine performance [g/kW.h or (L/kW.h)]

508 or (0.7)

NOISE INFORMATION

Sound pressure level at operator position (in accordance
with EN ISO 22868) [LpA dB(A)]

97.6

Measured sound power level dB(A) 109.7
Sound power level (in accordance with EN ISO 22868) [LwA

dB(A)]

111

(Uncertainty of noise is K=3dB.)

JCB-BC26_960443002-01_Manual_final.indd A8JCB-BC26_960443002-01_Manual_final.indd A8 12/2/2010 5:38:00 PM12/2/2010 5:38:00 PM