POWER TOOL
INSTRUCTION & USER MANUAL
EN
IM-18USB-EN
Original Instructions
JCB-18USB
2
JCB-18USB
Instruction & User Manual
GENERAL WARNINGS & DISPOSAL
To reduce the risk of injury, the user must read the instruction manual.
This product has been marked with a symbol relating to removing electric and
electronic waste. The product should not be discarded with household waste
but must be returned to a collection system which conforms to the European
Directive 2012/19/EU. It will then be recycled or dismantled in order to
reduce the impact on the environment. Electric and electronic equipment can
be hazardous for the environment and for human health since they contain
hazardous substances.
This symbol is used throughout this manual to warn the user about potential
risks. Please read & understand these sections before using the device.
The month and year of manufacture can be found within the product serial number e.g.
MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included.
Positive terminal
Negative terminal
3
JCB-18USB
Instruction & User Manual
Contents
CHARGER SAFETY 4
COMPONENT LIST 5
CHARGER TECHNICAL DATA 5
OPERATING INSTRUCTIONS 6
Intended Use 6
Maintenance 7
Transport and Storage 7
4
JCB-18USB
Instruction & User Manual
m To reduce risk of injury, only charge
JCB rechargable batteries. The
charger and battery packs are specifically
designed to work together. Other types of
batteries may burst causing fire and personal
injury.
m Do not allow any liquid to get inside
the charger. Electric shock may result.
m Do not expose the charger to rain or
snow.
m Under certain conditions with the
charger plugged into the USB device,
the exposed charging contacts
inside the charger can be shorted by
foreign materials. Foreign materials of a
conductive nature such as, but not limited
to, steel, wool, aluminium foil or any buildup
of metallic particles should be kept away
from charger cavities.
m Always unplug the charger from the
USB device when there is no battery
in the cavity.
m Unplug the charger from the USB
device before attempting to clean.
m Do not operate the charger with a
damaged USB cable.
m This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
CHARGER SAFETY
Read all safety warnings, instructions
and specifications provided with this
charger. Failure to follow all instructions
listed below may result in electric shock, fire
and/or serious injury. Save all warnings
and instructions for future reference.
WARNING!
5
JCB-18USB
Instruction & User Manual
JCB-18VFC
1.
USB CONNECTION (NOT VISIBLE)
2.
INDICATOR LED
3.
CHARGER
Charger Code Input Power Output
JCB-18USB 20V d.c. 5V d.c. / 2.0A max
CHARGER TECHNICAL DATA
3
2
1
6
JCB-18USB
Instruction & User Manual
OPERATING INSTRUCTIONS
Intended Use
This USB charger is indended for use only with
a compatible JCB 18V power tool & lithiumion battery pack.
The component must not be modified or used
for any other purposes than the ones described
in these instructions.
Battery
Make sure the power switch is not pressed
in when inserting or replacing the battery.
NOTE
m Do not force the battery when
connecting it, use moderate pressure.
An incorrectly connected battery can
damage the battery terminals or the battery
socket on the tool.
m Use the button on the battery to check the
charging status; 4 red LEDs indicates fully
charged, where 1 indicates low battery
status.
Charging The Battery
After charging for the first time, ensure the
battery is completely discharged before
placing on charge again. Repeat this charging
and discharging cycle 4 to 5 times to ensure
battery is correctly conditioned.
WARNING!
m Place the battery charger on a level and
stable surface. Connect your USB device
with a suitable cable to the rechargeable
battery adapter on the USB connection.
m Connect the battery to the charger so that it
clicks into place.
m Refer to the Battery Charge Level table
below for battery charger status as indicated
by LED lights.
m Unplug the charger from the power point
and remove the battery from the USB
device.
Battery Charge Level
Red
LED
Green
LED
Battery Charge Status
Charger is connected to
mains power
Connected battery is
charging
Connected battery is fully
charged
Connected battery has a
charging fault
Charger is outside correct
operating temperature
range (<0˚C / >40˚C)
If the LEDs on the charger do not come on
when charging:
m Check that the charger’s USB cable is
properly plugged into the USB device and
that the charger is switched on.
m Check that the battery is correctly inserted
in the charger.
Connecting the battery
m Connect the battery to the battery socket
on the tool so that it clicks into place.
Removing the battery
m Press the battery release button and remove
the battery from the tool.
7
JCB-18USB
Instruction & User Manual
Maintenance
Remove the battery pack from the tool or
charger before cleaning and maintenance.
This helps avoid the risk of electric shocks
and accidental injury.
WARNING!
m Wipe the charger with a dry or damp cloth.
Do not use a wet cloth. Do not use
detergent that contains solvent or
corrosive, abrasive additives. This risks
damaging the surfaces of the charger.
m Clear the battery connection terminals and
the release button of dust and dirt after
each use. Do not clean terminals by
inserting sharp objects in them, such
as screwdrivers and other similar
objects.
m Stubborn contamination in areas hard to
access can be removed with compressed air
(max 3. bar).
m Regularly check all fasteners, screws and
bolts to make sure that they are tight.
Tighten any loose screws immediately or
serious injury could occur.
Never open the battery pack. The battery
pack has no internal parts that the user can
service or repair. Never try to repair the
battery pack yourself. Take to an authorised
service centre.
WARNING!
Transport and Storage
m If the charger will remain unused for any
length of time, it should be stored in the
original packaging, or in a compatible JCB
power tool storage insert.
m Store the charger in a dry, frost-free, well
ventilated place with a temperature of no
more than 40°C.
m Keep all chargers out of the reach of
children.
m Always remove the battery from the charger
before transport.
m Ensure that the charger is not at risk of being
exposed to excessive vibration and shocks
during transport, especially if the charger will
be transported by car or other vehicle.
Loading...