Page 1
Page 2
Page 3
ENGLISH OPERATION MANUAL
CAUTION
OPERATION MANUAL
Thank you for buying this JB Systems® product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
Powerful 1200W snow machine.
Produces large amounts of artificial snow flakes.
Adjustable snow output volume:
via the wired remote control (included)
via the wireless remote control (included)
Recommended Fluid: JB Systems Snow Liquid
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
Operating instructions
YETI snow machine
Hanging bracket + with 2 knobs and 2 rubber rings (put the rings between the bracket and the machine).
Wired remote controller
Wireless remote controller
Wireless remote receiver
SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do not remove the top cover.
No user-serviceable parts inside. Refer servicing to qualified service
personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use
or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
This symbol means: indoor use only.
This symbol means: Read instructions.
This symbol determines: the minimum distance from objects. The minimum distance between fogger
output and objects must be more than 1 meter.
To protect the environment, please try to recycle the packing material as much as possible.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
This unit is for indoor use only.
JB SYSTEMS® 1/4 YETI
Page 4
ENGLISH OPERATION MANUAL
Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
Locate the unit in a well ventilated spot, away from any flammable materials and/or liquids.
Don’t cover any ventilation openings as this may result in overheating.
Prevent use in dusty environments and clean the unit regularly.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Make sure to always place the unit on a stable surface.
Always unplug the unit when it is not used for a longer time or before you start servicing.
Check that the available voltage is not higher than the one stated on the rear panel of the unit.
The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Never let the power-cord come into contact with other cables!
This unit must be earthed in order comply with safety regulations.
In order to prevent electric shock, do not open the cover.
Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
In the event of serious operating problems, stop using the unit and contact your dealer immediately.
The housing must be replaced if it is visibly damaged.
Please use the original packing when the device is to be transported.
Due to safety reasons it is prohibited to make unauthorized modifications to
the unit.
DESCRIPTION:
1. OUTPUT: with this knob you can select the speed of the fan.
2. WIRELESS REMOTE INPUT: Used to connect the supplied wireless
remote control receiver.
3. WIRED REMOTE INPUT: Used to connect the supplied wired remote
controller.
4. POWER SWITCH: Used to switch the power of the unit on/off.
5. INPUT FUSE: When the fuse is blown, first locate and solve the problem
that caused the fuse to blow. When the problem is solved, replace a
damaged fuse with a fuse of the same type and electrical specifications.
(250V-8A)
6. MAINS CABLE: to be plugged in a mains wall socket with earth
connection.
REMOTE CONTROLLER:
1. [OUTPUT] KNOB: this knob is used to set the output volume.
Turn the knob clockwise to increase the output
Turn the knob counterclockwise to decrease the ouput
2. [POWER] LED: when the unit is on, this Led will be lit.
3. [READY] LED: when the fan is switched on by the on/off button, this LED will be lit.
4. [ON/OFF] BUTTON: used to switch the fan on or off
JB SYSTEMS® 2/4 YETI
Page 5
ENGLISH OPERATION MANUAL
OPERATING INSTRUCTIONS
Put the snow machine on a flat and very stable surface.
Make sure the liquid tank is not empty. Always use good quality snow liquid to fill up the tank. Close the
tank immediately to prevent dirt to enter the reservoir!
Plug the supplied wired remote or the wireless remote receiver in the corresponding remote control input
on the back of the unit.
Make sure to plug the snow machine in a mains wall socket with earth connection
Switch the snow machine on.
WARNING: NEVER use the machine with an empty reservoir. This can damage the pump !
Used with the supplied wired remote controller:
Connect the special 5pin connector of the controller to the [WIRED REMOTE] input on the back of the
snow machine.
Use the [ON/OFF] button of the remote controller to start/stop the fan.
On the back of the unit, you can select the speed of this fan [High] or [Low]
Use the round button to set the output volume of the pump.
Used with the supplied wireless remote controller:
Connect the special 5pin connector of the wireless remote
receiver to the [WIRELESS REMOTE] input on the back of
the snow machine.
Fix the remote receiver with its magnetic surface to the
snow machine.
Pull out the antenna of the wireless remote controller.
This are the functions of the 4 buttons:
Button A: Decrease Output Volume
(5 steps of 20%)
Button B: Fan OFF
Button C: Increase Output Volume
(5 steps of 20%)
Button D: Fan ON
To produce artificial snow, fan + pump volume should be
both on
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
JB SYSTEMS® 3/4 YETI
Page 6
ENGLISH OPERATION MANUAL
MAINTENANCE
IMPORTANT:
Clean the machine after use and before long term storage.
Empty the tank or replace it by an empty spare tank.
To remove the deposit in a tank, rinse it with distilled water including 20% of white vinegar. Don’t run
the machine with this vinegar solution !
When the tank is clean, fill it up with distilled water and activate the machine. This will remove the
remaining snow fluid from the internal circuit and the pump.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
This device has been designed to produce decorative effect lighting and is used in light show systems.
Mains Input: AC 230V, 50Hz
Power consumption: 1200 Watt
DMX Channels: No DMX on board
Fuse: T8A/250V (slow blow 6x30mm)
Tank size: 5 L
Recommended Fluid: JB Systems Snow Liquid
Size: 530 x 260 x 320 mm (without hanging bracket)
Weight: 8.70 kg
All the information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.jb-systems.eu
JB SYSTEMS® 4/4 YETI
Page 7
Page 8
Loading...