JBL P650c, P550c User Manual

THANK YOU
for purchasing a JBL Power Series
®
automotive loudspeaker component system. We’ve organized this manual to make your installation as simple and trouble-free as possible. Please read it thoroughly before proceeding. Remember to keep your sales receipt and this manual in a safe place so both are available for future reference.
component systems owner’s manual
INSTALLATION WARNINGS AND TIPS
ABOUT THESE INSTRUCTIONS
Installation of automotive stereo com­ponents can require extensive experi­ence with a variety of mechanical and electrical procedures. Although these instructions explain how to install Power Series Component Systems in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your authorized JBL car audio dealer about professional installation options.
LOUD MUSIC AND HEARING
Playing loud music in an automobile can hinder your ability to hear traffic, as well as permanently damage your hearing. The maximum volume levels achievable with JBL speakers, com­bined with high power amplification, may exceed safe levels for extended listening. We recommend using low volume levels when driving. JBL accepts no liability for hearing loss, bodily injury or property damage as a result of use or misuse of this product.
REAR DECK PRECAUTION
In some cars, fuel tanks may be located directly beneath the rear deck. Before installation, make sure there is adequate speaker basket clearance before considering this location!
ABOUT THE CONTENTS
The Power Series Component System includes:
•5-1⁄4" or 6-1⁄ 2" or 165mm woofer
• Grille and mounting adapter(s)
• 1" tweeter with surface/flush I-Mount
(patent no. 5,859,917) kits
• Crossover network with mounting screws
NOTE: The supplied crossover net­work is designed to work with the above-listed transducers. Do not sub­stitute another crossover network or use other speakers when connecting the system (see Figure 7A).
INSTALLATION TIPS
• Always wear protective eyewear when using any tools.
•Turn off all audio components and other electrical devices before you start. Disconnect the (–) negative lead from your vehicle’s battery.
• Keep speakers in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. Never use force to install any speaker.
• Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface.
•At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas.
• Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw.
• For door installations, check the clearance with the windows throughout the range of the win­dow’s travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism.
• If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements.
• Do not mount speakers where they will get wet.
• If possible, select a mounting site for the crossover network that is near the speakers and provides easy access for connections.
Figure 1. Mounting the P550c woofer with the grille.
Figure 2. Mounting the P650c woofer with the grille.
Figure 3. Mounting the P650c in a standard 6" opening.
NOTE: The P650c uses an adapter to fit a variety of different 6" openings. Select an appropriate adapter ring and secure it to the vehicle using the sheet-metal screws provided, then attach the speaker to the ring with the machine screws.
Figure 4. Mounting the P650c in a 165mm speaker location.
INSTALLATION
ADAPTER RING
Figure 5. Mounting the tweeter using the I-Mount flush-mounting kit.
Figure 6. Aiming the tweeter at a desired listening position.
Figure 7. Mounting the tweeter using the I-Mount surface-mounting kit.
Big Lug =
Small Lug =
To AMPLIFIER SPEAKER OUTPUTS
To WOOFER
To TWEETER
Red
Blk
INSTALLATION
CONNECTIONS
1)
push in
2) turn
3
)
4
)
+
red
blk
1. Slide screw up or down to adjust tweeter angle.
4. Securely tighten the large hand nut.
2. Tighten nut and washer to lock angle settings.
3. Rotate to aim angled tweeter toward listener.
1
2
+
red
blk
Open the crossover housing by firmly squeezing the sides of the top half and lifting it away from the bottom. Using screws or a wire tie, mount the crossover using the holes provided. Observing proper polarity, connect the speakers and amplifier as shown in Figures 8A and 8B. Replace the cover when you are finished making the connections and adjustments (see following section).
Figure 8A. Wiring connections on the crosssover network (shown with cover on).
Figure 8B. Locating wiring connections on the P552 woofer. Other woofers are wired similarly.
The Power Series component crossover features a tweeter-level adjustment. The tweeter level may be set to 0dB (flat response), or it may be attenuated by approxi­mately 3dB to suit the listener’s preference. The factory default position is 0dB; if this is the desired setting, it is not necessary to make any changes.
If a reduced tweeter output level is desired, carefully remove the small plastic jumper from the pins marked “0dB” and place it across the two pins marked “–3dB” (refer to drawings below).
Flat
–3dB
Jumper
0dB
-3dB
0dB
-3dB
Jumper
2R0
R2
PTC
LP135
L1
R1
12u
C2
POWER P550C
MT2.2u
0.15mH*0.7R
2R0
0.08mH*0.7R
C1
0dB
-3dB
L2
T+T-W+W-In+In-
SPECIFICATIONS
P550c P650c
Type: 5-1/4" two-way component system 6-1/2" two-way component system Speaker Impedance: 4 ohms 4 ohms Power Handling: 70W RMS, 210W Peak 90W RMS, 270W Peak Sensitivity (2.83V, 1m): 89dB 90dB Frequency Response: 55Hz – 23kHz 45Hz – 23kHz Mounting Depth: 2-3⁄16" (56mm) 2-1/4" (58mm) Cut-Out Diameter: 4-11/16" (120mm) 5-1/16" (129mm)
GENERAL CARE
The loudspeaker grilles may be cleaned with a damp cloth. Do not use any cleaners or solvents on the grilles or the speaker cones. A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
Declaration of Conformity
We,Harman Consumer International
2, route de Tours 72500 Chateau-du-Loir France
declare in own responsibility that the products described in this owner’s manual are in compliance with technical standards:
EN 50081-1:1992 EN 50082-1:1997
Emmanuel Millot
Harman Consumer International
Chateau-du-Loir, France. 2/03
JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY 11797 USA
1.800.336.4JBL (4525) • FAX 1.516.682.3523 • www.jbl.com © 2003 Harman International Industries, Incorporated JBL is a registered trademark of
Harman International Industries, Incorporated. Part No. P550C/P650COM2/03
Loading...