jbc pulsmatic User Manual

PULSMATIC

SOLDERING IRON WITH SOLDER FEED

Index Page

English 1
Español 3
Français 5
Deutsch 7
Italiano 9

www.jbctools.com

We would like to thank you for the trust you have shown in JBC in acquiring our
soldering iron with its solder feed system. It has been made to the highest quality
standards to provide you with the best service.
Before using this equipment, we recommend you read these instructions carefully.

ENGLISH

1

TECHNICAL DATA
55 N 230V Ref. 2552016

- Power supply: 230 V

- Power: 30 W

- Maximum temperature: 410°C

- Time to reach 250°C: 2 min.
Includes the following:

- Long-life tip C20D Ref. 0550509

- Replacement reel

INSTRUCTIONS FOR USE

Check that the mains voltage is the same as
specified on the unit.
Do not plug in the soldering iron without a tip,
as this might damage the element.
To avoid incidents, the hot soldering iron should
be kept inside the TS 1200 holder stand (Ref.

0290120), which is available as an extra.

SOLDER REEL TYPES:

- Solder reel with ø1mm solder wire. Alloy:
99%Sn / 0.3%Ag / 0.7%Cu - 50gr. Green
solder reel. SN5450

REPLACING THE REEL

The reel is pressed into the support arm, where
it is held in place.
To extract the reel, rest the shaft end on a
convenient surface and press down on the
reel until it gives in.

Before fitting a new reel, pull out the solder
remaining inside the guide tube.

The solder flux may cause clogging at the
end of the guide tube: clean when necessary.

To fit the new reel, position it in such a way
that the solder wire runs off at the bottom;
insert the end of the wire into its hole and
feed it in until it becomes engaged in the
feed mechanism.

Always use solder wire of 1 mm in diameter.

This product should not be thrown in
the garbage.

BE-SA

ENGLISH

1 Remove the ring to disengage the tip.

2 Remove the tip by pulling the soldering iron

backwards.

3 Insert the new tip and make sure it has gone

all the way in.

JBC reserves the right to make technical changes without prior
notification.

SOLDER REEL HOLDER

For production-line purposes we recommend
using our holder BE-SA, which enables solder
reels in sizes up to 2.5 kg to be used. Simply
wrap a couple of turns of the solder wire
around an empty reel as shown.

TIP CARE

- Unplug the soldering iron.

- To clean the tips, use the damp sponge in­cluded with the JBC stand. Only deionised
water (car battery watter) should be used
in order to wet the sponge. If normal water
was to be used, it is very likely that the tip
will become dirty due to the salts dissolved
within the water.

- Do not file the tips or use abrasive tools which
may damage the tip’s protective surface
coating and avoid knocking them about.

- If the tip has been a long time with­out being tinned, use the metal brush
Ref. 0297705 adaptable to the support, to
remove any dirt and oxide.

REPLACING THE TIP

Use the tip extractor Ref.0114108, and
proceed as shown in these diagrams.

2

Agradecemos la confianza depositada en JBC al adquirir nuestro solda dor con
aportación de estaño. Ha sido fabricado con las más estrictas normas de calidad,
para prestarle el mejor servicio.
Antes de poner en marcha el aparato, recomendamos leer con atención las instrucciones
que a continuación se detallan.

ESPAÑOL

3

DATOS TECNICOS
55 N 230V Ref. 2552016

- Alimentación 230 V.

- Potencia: 30 W

- Temperatura máxima: 410°C.

- Tiempo para 250°C: 2 min.

Se suministra con:

- Punta Larga duración C 20D Ref.0550509

- Bobina de estaño

INSTRUCCIONES DE FUNCIONAMIENTO

Compruebe que el voltaje de la red sea el
indicado en el aparato.
No conectar el soldador sin punta, podría
dañar la resistencia.
Para evitar incidentes, el soldador caliente debe
guardarse en el interior del soporte TS 1200
Ref. 0290120 disponible como complemento.

CAMBIO DE CARRETE

El carrete está introducido a presión en el brazo
del soporte, quedando sujeto por el anclaje
del mismo.
Para extraerlo, apoye el extremo del eje sobre
una superficie y presione sobre el carrete hasta
vencer la resistencia.

El fundente del estaño, puede provocar la
obstrucción del extremo del tubo guía, límpielo
si es necesario.

Para colocar el nuevo carrete, oriéntelo para
que el hilo de estaño salga por la parte inferior
e introdúzcalo en el orificio de entrada hasta
que el mecanismo de arrastre pueda actuar.

Utilice siempre hilo de estaño de 1 mm de
diámetro.

Este producto no debe ser tirado a la
basura.

TIPOS DE BOBINA DE ESTAÑO:

- Bobina con hilo de ø1mm. Aleación: 99%Sn
/ 0.3%Ag / 0.7%Cu - 50gr. Carrete color
verde. SN5450.