Page 1
IR Preheater Support
Ref. PHS-SA
www.jbctools.com
Page 2
2
Packing List
The following items should be included:
Allen key ..................................................... 1 unit
Ref. 0013754
Manual ....................................................... 1 unit
Ref. 0017154
Ref. PHS-SA
IR Preheater Support
IR Preheater Support ............................................................................................................................ 1 unit
Ref. PHS-SA
www.jbctools.com
Page 3
3
ESD safe connector
Sliding guideSpring guide
Clamp knobs
Rubber caps
Heater Unit
For fixing irregular shaped
PCBs to the suppor t.
For fixing identical PCBs
in the same position.
Slot clamps
Allen key
Features
Page 4
4
1. Remove the 4 clamp knobs
and the 4 black rubber caps.
180°
For PCBs of 0.8 - 2.4mm thick
For PCBs of 2.4 - 6mm thick
28mm
50mm
For PCBs over 6mm thick
70mm
2. After removing both guides,
turn 180° the guide supports.
3. Place the guides, the
rubber cups and adjust the
sliding clamp knobs again.
Remove these knobs if necessary
Height Adjustment
It allows adjustment for 3 heights between the PCB and the Heating Area of the PHS-B Heater Unit.
Low level
High level
Medium level
To change the height, do as follows:
Page 5
5
After loosening the SP guide knobs, push the
PCB against the SP guide and lift out.
Place large PCBs on
the 4 rubber cups
Push the PCB against the SP guide, position it
and tighten the SP guide knobs.
Changing PCBs of the same batch
The support lets you place PCBs of the same batch so as to always heat the same area.
Use the sliding guides to change the PCBs.
Removing the PCB
Placing another PCB
Reworking large PCBs
Page 6
6
Axes of the sliding guide
Safety
It is imperative to follow safety guidelines to protect health and prevent electric
shock, injury, fire or explosions.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
Be careful with the remains of liquid tin. In contact with skin, it can cause burns.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the smoke produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- This appliance can be used by children over the age of eight as well as persons with reduced
physical, sensory or mental capabilities or lacking experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Maintenance
Before carrying out maintenance or storage,
always allow the support to cool.
- Check periodically that the support is clean,
especially the axes of the sliding guide.
- Replace any defective or damaged piece.
Use original JBC spare parts only.
- Repairs should only be performed by a JBC
authorized technical service.
Page 7
7
Exploded View
Page 8
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased. Please register your
product warranty within 30 days of purchase in
www.jbctools.com/productregistration.
Manual in other languages available on our website
001715 4-0 817
Specifications
- Weight: 2 kg (4.4 lb)
- Dimensions (Low Position): 267 x 259 x 75 mm (10.5 x 10.2 x 3 in)
- Dimensions (High Position): 267 x 259 x 96 mm (10.5 x 10.2 x 3.8 in)
Complies with CE standards.
ESD protected housing.
www.jbctools.com
Loading...