www.jbctools.com
INSTRUCTION MANUAL
Stands for Tweezers
Ref. PA-SE / HT-SE
Packing List
Stand ............................................................ 1unit
Ref. PA-SE
Stand ............................................................ 1 unit
Re f. H T- SE
The following items should be included in each stand:
Stand Cable 1m................................ 1 unit
Re f. 001128 3
2
Manual .......................................................... 1 unit
Ref. 0018082
www.jbctools.com
INSTRUCTION MANUAL
Stands for Tweezers
Ref. PA-SE / HT-SE
Features
www.jbctools.com
Stand
To Control Unit
Extractors
Ref. HT-SE
HT-SE tool placement for large tips
To tool
Loosen the screw. Place the Soldering Iron in
the extractor and remove the cartridge.
Insert the new car tridge and press slightly
as far as the mark and tighten the screw.
Loosen
3
Assembly: Cable Collector and Adjustable Tool Holder
4
Accessories
www.jbctools.com
Stand extension cable
Ref. A1286
Length: 1.5m
Stand Cable
5
Maintenance
Before carrying out maintenance or storage,
always unplug the stand from the station and
the tool.
- Use a damp cloth to clean the stand.
Alcohol can be used only when cleaning
the metal parts.
- Check periodically that the metal par ts of
the tool/stand are clean so that the station
can check the tool’s status.
- Periodically check all cables and tube
connections.
- Replace any defective or damaged parts.
Use original JBC spare parts only.
- Repairs should only be performed by a
JBC authorized technical service.
Clean periodically
6
www.jbctools.com
Safety
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to activate the sleep mode.
The soldering tip, the metal part of the tool and the stand may still be hot even when the station
is turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Avoid the contact of flux with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
7
Specifications
PA-SE
- Includes Sleep Mode
- Net Weight 1.30 kg (2.87 lb)
- Package Weight 1.59 kg (3.51 lb)
- Package Dimensions 342 x 155 x 120 mm (13.46 x 6.10 x 4.72 in)
HT-SE
- Includes Sleep Mode
- Net Weight 1.41 kg (3.11 lb)
- Package Weight 1.68 kg (3.72 lb)
- Package Dimensions 342 x 155 x 120 mm (13.46 x 6.10 x 4.72 in)
Complies with CE standards
ESD protected
Warranty
JBC’s two-year warrant y covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour. Warranty
does not cover product wear or misuse. In order for
the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased.
Register your warranty within 30 days of purchase
in www.jbctools.com/productregistration
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facilit y.
Manual in other languages available on our website
www.jbctools.com
00 21651- 0518
Loading...