is a registered trademark of Schoenberger Germany Enterprises GmbH & Co. KG • Zechstraße 1 – 7 • 82069 Hohenschäftlarn
1
1
Operating manual
Overview of functions ..................................................................................................................................... 2
Technical data and scope of delivery
.........................................................................................................2
Operation
..................................................................................................................................................... 3 – 5
Contact information
........................................................................................................................................6
8 channel/16 channel
Hand-held radio transmitter, type -08 l TDRC-16
The signatory declares that the hand-held radio transmitter conforms with the Guidelines and Directives according to
R&TTE 1999/5/EC.
Models: TDRC - 08, TDRC - 16
DIN EN 301489-3:2013-12, DIN EN 300220-3
Schoenberger Germany Enterprises GmbH & Co. KG
Zechstraße 1-7
82069 Hohenschäftlarn
WEEE Reg. No. DE 41060608 for: JAROLIFT
®
™
Michael Mayer
Managing Director
Rev._07.2014
compliant
2002/95/EC
RoHS
2
Overview of functions/technical data & scope of delivery
OPEN
STOP
CLOSE
Technical data and scope of delivery
Technical data
Power supply: 3 Volt
Battery model: CR2430
Operating current: ≤12 mA
Protection: IP 30
max. authorised permissible ambi-
ent temperature:
-10°C to +60°C
Encoding the radio: Rolling code
Radio frequency: 433.92 MHz
Channels: 8 channel or 16 channel
Compatibility: Compatible with all TDR wireless motors and receivers, as of production date 03/2010
After you have unpacked the device, check the package content
with the information on the delivery slip:
1. Hand-held transmitter TDRC-08 or TDRC-16
2. Wall bracket
Operating Instructions
K1
K2
K3
Please note:
The symbols for groups and individual control ( ) are not displayed
on the TDRC-16 hand-held transmitter
1
2
1 2 3 4 5 6 7 8
SM
SM
Channels
Active channel
Multi
(Group control)
Single
(Individual control)
3
Operation
Adaptation of the hand-held transmitter
1 Use the K3 button (description see Page 2) on the hand-held transmitter and select the channel on which you would like to program the
transmitter (the active channel is highlighted and framed in the channel bar at the bottom of the display).
2 Now, set the respective radio receiver or wireless motor to the “TEACH” mode and follow the applicable instructions.
3 Within 10 seconds, press the OPEN and CLOSE button on your hand-held transmitter simultaneously and briey press the STOP button
If the “TEACH” process was successful, it is acknowledged by the brief vibration of the tubular motor that is attached to the radio receiver, or
the vibration of the wireless motor. Now you can use the OPEN/STOP/CLOSE button to activate the motor on your transmitter.
Individual operation
Use the buttons K1 and K3 (for button description, see Page 1) to select in the relevant channel or motor.
Briey press the OPEN, STOP or CLOSE button in order to control the operating mode of the motor
Press the K3 button
to select the active
channel
Follow the instructions
and set the receiver to
the “TEACH” mode
Press the OPEN/CLOSE
button simultaneously,
subsequently pressed
the STOP button.
Motor vibrates
Press the K3 button
to select the active
channel
Use the OPEN, CLOSE,
and STOP button
to actuate the motor
Setting the group control
1 First, press the K2 button on the hand-held transmitter for two seconds in order to activate the group control mode.
The select channel blinks in the upper left-hand corner of the display.
2 Now, you can use the K1 and K3 buttons in order to select the relevant channels.
By pressing the K2 button briey, you can add the active channel (a square is used to highlight it in the display) to the group.
Follow the same process if you wish to add additional channels to the group.
3 In order to remove a channel from the group, use the K1 and K3 button to select the channel that must be deleted,
and press the K2 button briey.
4 If you are satised with your settings, press the OPEN, STOP, or CLOSE button in order to leave the group allocation.
Now, you can use the operating keys to activate the generated groups
Press the K2 button
for 2 seconds
use the K3 button to
select the relevant
channels and at that
and by pressing K2
Use in the OPEN/STOP or DOWN button
to end the group allocation
Each button must be depressed for approx. 1 second!
is a registered trademark of Schoenberger Germany Enterprises GmbH & Co. KG • Zechstraße 1 – 7 • 82069 Hohenschäftlarn
4
Contact information
4
If you have any concerns about our product or your unit is faulty, please contact us in writing or send an email to the following
address:
is a registered trademark of
Schoenberger Germany Enterprises GmbH & Co. KG
Zechstraße 1 – 7
82069 Hohenschäftlarn
Tel.: 08178 / 932 932 / 3,425
Fax: 08178 / 932 939 / 425
info@jarolift.de
www.jarolift.de
Subject to technical changes, misprints and errors.
Rev._07.2014
Loading...