Jandy AE-Ti, AE2000, AE2500, AE3000 Installation And Operation Manual

Installation and Operation Data

Installation and
Op er a tion Man u al

Jandy® Heat Pumps

Model AE-Ti

DANGER

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. The electrical supply to this product

must be installed by a licensed or certifi ed electrician in accordance with the National Electrical
Code and applicable local codes and ordinances. Improper installation will create an electrical
hazard, which could result in death or serious injury to pool or spa users, installers, or others
due to electrical shock, and may also cause damage to property. Read and follow the specifi c
instructions inside this manual.

DANGER

RISQUE DE CHOC ÉLECTRIQUE OU ELECTROCUTION. Cet appareil doit être installé par un

électricien certifi é conformément au National Electrical Code et aux normes et règlementations
locales. Une installation incorrecte peut entraîner un risque de problème électrique ( choc
électrique ou électrocution) pouvant causer des blessures graves et même la mort des
installateurs et/ou utilisateurs de SPA et Piscines. Lire le manuel et se conformer aux directives.

PELIGRO

RIESGO DE DESCARGA ELÉCTRICA O ELECTROCUTAMIENTO. El suministro eléctrico de

este producto deberá ser instalado por un electricista autorizado o diplomado, de acuerdo al
Código Eléctrico Nacional y a los códigos y normativas que apliquen localmente. Una instalación
inadecuada podría originar riesgos eléctricos y ocasionar la muerte o lesiones graves a los
usuarios de de la piscina o spa, instaladores u otros, como consecuencia de una descarga
eléctrica, pudiendo así mismo ocasionar daños a la propiedad. Léa y siga las instrucciones
específi cas que se recogen en este manual.

H0569300A

Table of Contents

Page 1

Section 1. General Information ..................2

1.1 Introduction.................................................. 2

1.2 Consumer Information and Safety............... 2

1.2.1 Spa/Hot Tub Safety Rules..................... 2

1.2.2 Swimming Pool Energy Saving Tips ..... 3

1.3 Warranty...................................................... 3

1.4 Codes and Standards.................................. 4

1.5 Technical Assistance ................................... 4

1.6 Materials Needed for Installations ............... 4

1.6.1 Materials for All Installations.................. 4

1.6.2 Recommended Materials for

Installations ........................................... 4

1.7 Specifi cations .............................................. 4

1.7.1 General Specifi cations .......................... 4

1.7.2 Dimensions ........................................... 5

Section 2. Installation Instructions ............5

2.1 General Information..................................... 5

2.2 Location Requirements ............................... 5

2.2.1 Introduction ........................................... 5

2.2.2 Clearances............................................ 6

2.2.3 Equipment Pad...................................... 6

2.2.4 Condensation and Drainage ................. 6

2.2.5 Lawn Sprinklers..................................... 6

2.2.6 Roof Run-Off ......................................... 6

2.2.7 Installation of Anchor Clamps................ 7

Section 3. Water Connections....................7

3.1 Plumbing Layout.......................................... 7

3.2 Water Connections at Heat Pump............... 8

3.3 Check Valve Installation .............................. 8

3.4 Automatic Flow Control Valve ..................... 9

3.5 Multiple Unit Installation .............................. 9

3.5.1 Heat Pump And Heater Combination.... 9

3.5.2 Multiple Heat Pump Connections.......... 9

Section 5. Continued

5.2 Operating the Controller ............................ 18

5.2.1 On/Off Button ...................................... 18

5.2.2 Pool Mode (Normal Heat) ................... 18

5.2.3 Pool Mode (Optional Auto Heat) ......... 19

5.2.4 Spa Mode (Optional Auto Heat).......... 19

5.2.5 Keypad Lockout .................................. 19

5.2.6 Feature Lockout .................................. 19

5.3 Operating Features of Units with

Optional Chiller.......................................... 20

5.3.1 Pool Mode (Normal Cool).................... 20

5.3.2 Pool Mode (Auto Cool)........................ 20

5.3.3 Spa Mode (Auto Cool)......................... 20

5.4 Enabling Remote Control with
AquaSwitch

Dual TStat Remote Systems ..................... 20

5.5 Enabling Remote Control with
AquaLink

5.6 Advanced Digital Microprocessor

Quick Guide............................................... 21

5.7 Water Pressure Switch Adjustment ........... 21

®

Systems and Other

®

RS Systems ............................ 20

Section 6. General Maintenance .............22

6.1 Water Chemistry........................................ 22

6.2 Winterizing................................................. 22

6.3 Spring Start-Up.......................................... 23

6.4 Inspection and Service .............................. 23

6.4.1 Owner Inspection ................................ 23

6.4.2 Professional Inspection ....................... 24

Section 7. Professional Maintenance

And Service..............................25

7.1 Heat Pump Design .................................... 25

7.2 Heat Pump Components and

Their Operation ......................................... 25

Section 4. Electrical Connections............12

4.1 General Information................................... 12

4.2 Main Power ............................................... 15

4.3 Bonding ..................................................... 15

4.4 Pump Connection (Auto-Heat Feature) .... 16

4.5 Optional Remote Controls ......................... 16

4.5.1 Connection to an AquaLink RS

Control System ................................... 16

Section 5. Operation .................................18

5.1 Initial Start-up Precautions ........................ 18

Section 8. Troubleshooting ......................26

8.1 Troubleshooting Guide .............................. 26

8.2 Diagnostics................................................ 27

Section 9. Replacement Parts..................29

9.1 Ordering Information ................................. 29

9.2 Jandy® AE-Ti Heat Pumps Parts List........ 29

9.3 Jandy® AE-Ti Heat Pumps

Exploded View........................................... 30

Warranty ...................................Back Cover

Page 2

Section 1.
General Information

1.1 Introduction

This manual provides installation and operation
instructions for the Jandy AE-Ti models of Heat Pumps.
Read these installation and operation instructions
completely before proceeding with the installation.
Consult Jandy with any questions regarding this
equipment. To obtain additional copies of this manual
contact us at 707-776-8200 ext. 237. The following is
the address information for Jandy:

2735 NW 63rd Court.

Fort Lauderdale, FL USA 33309

The AE-Ti heat pump gets electrical power from
an external source and provides a dual electronic
thermostat control system for pool/spa combinations or
preheat convenience.

This heat pump is specifically designed for heating
fresh water swimming pools and spas. Do not use it
as a general service heater. Consult your dealer for the
appropriate Jandy products for these applications.

NOTE “Fresh water swimming pools and spas” include

systems that utilize saltwater chlorine generator
units, such as the Jandy AquaPure Electronic
Chlorine Generator. Please ensure that the salt
content of the pool/spa does not exceed
4000 ppm and water fl ow rate is within
60-80 gpm (225-300 lpm)

ATTENTION

Installation and service must be performed by
a qualifi ed installer or service agency.

To the Installer: After installation, these

instructions must be given to
the homeowner or left on or
near the heat pump.

To the User: This manual contains

important information that
will help you in operating and
maintaining this heat pump.
Please retain it for future
reference.

1.2 Consumer Information and Safety

The AE-Ti series of heat pumps are designed
and manufactured to provide many years of safe
and reliable service when installed, operated and
maintained according to the information in this manual
and the installation codes referred to in later sections.

Throughout the manual, safety warnings and cautions
are identified by the “ “ symbol. Be sure to read and
comply with all of the warnings and cautions.

1.2.1 Spa/Hot Tub Safety Rules

WARNING

The U.S. Consumer Product Safety Commission
warns that elevated water temperature can
be hazardous. Consult heater operation and
installation instructions for water temperature
guidelines before setting temperature.

AVERTISSEMENT

La Commission U.S. de Sécurité des Produits
pour les Consommateurs indique que des
températures de l’eau élevées peuvent être
dangereuses. Voir la notice d’installation
et de fonctionnement pour le réglage de la
température.

AVISO

La Comisión de Seguridad de Productos para
el Consumidor de los Estados Unidos, advierte
que una temperatura elevada del agua puede
ser peligrosa. Consulte las instrucciones de
instalación y funcionamiento del calentador
para seguir las directrices relacionadas con la
temperatura del agua antes de proceder a fi jar
la temperatura.

WARNING

The following “Safety Rules for Hot Tubs,”
recommended by the U.S. Consumer Product
Safety Commission, should be observed when
using the spa.

AVERTISSEMENT

Les Règlements suivants pour Cuves
Thermales, tel que recommandés par la
Commission U.S. de Sécurité des Produits pour
les Consommateurs, devraient être respectés
lors de l’utilisation du spa.

AVISO

Al utilizar el spa, deberán observarse, las
siguientes “Reglas de Seguridad para Baños
Calientes” recomendadas por la Comisión de
Seguridad de Productos para el Consumidor de
los Estados Unidos.

Page 3

1. Spa or hot tub water temperature should never
exceed 104°F (40°C). One hundred degrees
Fahrenheit (100°F [38°C]) is considered safe for a
healthy adult. Special caution is recommended for
young children.

2. The drinking of alcoholic beverages before or
during spa or hot tub use can cause drowsiness
which could lead to unconsciousness, and
subsequently result in drowning.

3. Pregnant women take note! Soaking in water
above 102°F (38.5°C) can cause fetal damage
during the fi rst three months of pregnancy (which
could result in the birth of a brain-damaged or
deformed child). If pregnant women are going
to use a spa or hot tub, they should make sure
the water temperature is below 100°F (38°C)
maximum.

4. The water temperature should always be checked
with an accurate thermometer before entering a
spa or hot tub. Temperature controls may vary by
as much as 1F° (1C°).

5. Persons with a medical history of heart disease,
diabetes, circulatory or blood pressure problems
should consult their physician before using a hot
tub or spa.

6. Persons taking any medication which induces
drowsiness (e.g., tranquilizers, antihistamines, or
anticoagulants) should not use spas or hot tubs.

7. Prolonged immersion in hot water can induce
hyperthermia.

Hyperthermia occurs when the internal body

temperature reaches a level several degrees above the
normal body temperature of 98.6°F (37°C). Symptoms
include dizziness, fainting, drowsiness, lethargy, and an
increase in the internal body temperature. The effects of
hyperthermia include:

1.2.2 Swimming Pool Energy Saving Tips

It is important to note that a heat pump will not
heat a pool as fast as a large gas or electric pool heater.
If the pool water is allowed to cool significantly, it may
take several days to return to the desired swimming
temperature. For weekend use, it is more economical
to maintain the pool water temperature at or near your
desired swimming temperature. If you do not plan to
use your pool for a prolonged period, then you might
choose to turn the heat pump completely off or decrease
the temperature setting of the control several degrees to
minimize energy consumption.

Jandy offers the following recommendations to
help conserve energy and minimize the cost of operating
your heat pump without sacrificing comfort.

1. The American Red Cross recommends a maximum

water temperature of 78°F (25°C). Use an accurate

pool thermometer. A difference of 4°F (2°C) ,

between 78°F and 82°F (26°C and 28°C), will

signifi cantly increase energy consumption.

2. Carefully monitor the water temperature of your

pool in the summertime. You can reduce heat

pump usage due to warmer air temperatures.

3. During the winter or when on vacation for longer

than a week, turn off the heat pump.

4. Find the proper setting on the heat pump

temperature control and use the Keypad Lock

function or lock the smoke-colored cover on

the heat pump controller to discourage further

adjustments.

5. Set the pump time clock to start the pump no

earlier than 6:00 AM during the pool heating

season. This is the time when nightly heat loss

balances.

6. Where possible, shelter the pool from prevailing

winds with well-trimmed hedges or other

landscaping, cabanas, or fencing.

• Lack of awareness of impending hazard

• Failure to perceive heat

• Failure to recognize need to leave spa

• Physical inability to leave spa

• Fetal damage in pregnant women

• Unconsciousness resulting in a danger of
drowning

7. Always use a pool cover when practical. Besides
providing a valuable safety feature, a pool cover
will reduce heat loss, conserve chemicals, and
reduce the load on fi lter systems.

1.3 Warranty

The AE-Ti heat pump is sold with a limited factory

warranty. Details are specified on the back cover of this
manual.

Page 4

Make all warranty claims to an authorized Jandy
dealer or directly to the factory. Claims must include the
heat pump serial number and model (this information
can be found on the rating plate), installation date, and
name of the installer. Shipping costs are not included in
the warranty coverage.

The warranty does not cover damage caused by
improper assembly, installation, operation, winterizing,
field modification, or failure to earth bond and
properly ground the unit. Any changes to the heat
pump, evaporator, heat exchanger, wiring, or improper

installation may void the warranty.

1.4 Codes and Standards

The AE-Ti heat pump is listed by ETL as
complying with the latest edition of the “UL Standard
for Safety for Heating and Cooling Equipment”, UL
1995 and CSA C22.2 No. 236.

All Jandy heat pumps must be installed in
accordance with the local building and installation
codes as per the utility or authority having jurisdiction.
All local codes take precedence over national codes. In
the absence of local codes, refer to the latest edition of
the National Electric Code (NEC) in the United States
and the Canadian Electric Code (CEC) in Canada for
installation.

1.5 Technical Assistance

Consult Jandy Technical Support Department or
your local Jandy dealer with any questions or problems
involving the specifications, installation, and operation
of your Jandy equipment. An experienced technical
support staff is ready to assist you in assuring the proper
performance and application of Jandy products. For
technical support call the Jandy Heat Pumps Technical
Service Department at [phone]

1.6 Materials Needed For Installation

1.6.1 Materials for All Installations

The following items are needed and are to be
supplied by the installer for all heat pump installations:

1. Plumbing connections (2”).

NOTE Flex conduit is recommended for connecting

the electrical supply wires to the heat pump so
that the front panel may be removed easily for
servicing.

4. Electric cutout switch that will interrupt all power
to the unit. This switch must be within line of sight
of the heat pump.

5. Watertight conduit to run the electrical supply line.

1.6.2 Recommended Materials for
Installations

Jandy recommends installing isolation valves
on the inlet and outlet water connections for ease of
serviceability.

1.7 Specifi cations

1.7.1 General Specifi cations

Installation Location
Certified for use in:

USA

Canada

Mexico

Central and South America

Water Pipe/Heater Connection

Plastic 2” PVC (Unions

Flow Rate

Maximum

Optimum

Minimum

Maximum Working Water
Pressure

Electrical Supply

Voltage Requirements
1-Phase

Indoor/Outdoor
approved
Indoor/Outdoor
approved
Indoor/Outdoor
approved
Indoor/Outdoor
approved

included)

125 gpm
(475 lpm)
55 gpm
(210 lpm)
30 gpm
(110 lpm)

75 psi

208/230 VAC 60Hz

2. Level surface for proper drainage.

3. Suitable electrical supply line. See rating plate on
unit for electrical specifi cations. A junction box is
not needed at the heat pump; connections are made
inside of the heat pump electrical compartment.
Conduit may be attached directly to the heat pump
jacket.

3-Phase

Amperage Protection
Requirements
AE2000
AE2500
AE3000

208/230 VAC60 Hz,
(Model dependent)

1-Phase
40 A
50 A
50 A

3-Phase
30 A
30 A
30 A

Page 5

33

3.5

10.75

11.5

MODEL

SIZE
2000 38" 26" 22" 13"

2500 42" 30" 26" 17"
3000 42" 30" 26" 17"

Figure 1. Jandy AE-Ti Heat Pumps Dimensions

1.7.2 Dimensions

A

B

DIMENSIONS

"A " "B " "C " "D"

2.2 Location Requirements

36

C

D

See Figure 1 for a diagram showing the heat
pump’s dimensions and for dimensions to critical
connections.

Section 2. Installation Instructions

2.1 General Information

Install the Jandy heat pumps in accordance
with the procedures in this manual, local codes and
ordinances, and in accordance with the latest edition of
the appropriate national code. (See Section 1.4, “Codes
and Standards”.)

Correct installation is required to assure safe
operation. The requirements for Jandy heat pumps
include the following:

1. Field assembly (if required).

2. Appropriate site location and clearances.

3. Suffi cient air ventilation.

4. Proper electrical wiring.

2.2.1 Introduction

NOTE Indoor installations require special

considerations for condensate drainage and
venting the cold air produced by the heat
pump. Contact the Jandy Heat Pump Technical
Service Department at [phone].

CAUTION

When pool equipment is located below the pool
surface, a leak from any component can cause
large scale water loss or fl ooding. Waterpik
Technologies cannot be responsible for such
water loss or fl ooding or resulting damage.

ATTENTION

Lorsque l’équipement d’une piscine est situé
sous la surface de l’eau, une fuite provenant de
n’importe quel élément peut causer une perte
d’eau importante ou une inondation. Waterpik
Technologies n’est pas responsable des pertes
d’eau, des inondations ou des avaries causées
par une installation ou un entretien inadéquat.

5. Adequate water fl ow.

This manual provides the information needed to
meet these requirements. Review all application and
installation procedures completely before continuing the
installation.

PRECAUCIÓN

Cuando el equipo de la piscina esté situado
por debajo de la superfi cie de la piscina, la
fuga de cualquiera de los componentes, podría
ocasionar la pérdida de grandes cantidades de
agua o inundación. Waterpik Technologies no
se responsabilizará de dichas pérdidas de agua
o inundaciones, ni de los daños que puedan
derivarse de las mismas.

Page 6

Table 1. Heat Pump Clearances

Side of Heat
pump

Minimum Clearances for

Operation

Inches Centimeters Inches Centimeters

Front

Rear

Left

Right

To p

6152460

6151230

6151230

6151230

60 150 60 150

Recommended Clearances for

Serviceability

NOTE Clearances listed in

Table 1 are manufacturer ’s

tested values. These are

given as minimum values.

Where local and national

codes apply, and values are

different than those listed in

Table 1, use the greater value

to ensure safe and proper

operation.

Avoid placing the heat pump in locations where
it can cause damage by water or condensate leakage. If
this is not possible, provide a suitable drain pan to catch
and divert any leakage.

All criteria given in the following sections reflect
minimum clearances. However, each installation must
also be evaluated, taking into account the prevailing
local conditions such as proximity and height of walls,
and proximity to public access areas.

2.2.2 Clearances

The heat pump must be placed to provide
clearances on all sides for maintenance and inspection.
See Table 1.

24” (61cm) access in front of the heat pump
provides adequate room for serviceability.

If the heat pump is to be installed in a garage
or under a vertical overhang, the unit must have a
minimum of 5 feet clearance from the top of the heat
pump.

This heat pump must be installed at least 5 feet
(1.52 meters) from the inside wall of the pool or spa
unless the heat pump is separated from the pool or spa
by a 5 foot high solid fence or other permanent barrier.

Ce chauffe-piscine doit être installé á au moins 5
pieds (1.5 m) de la paroi interne de la piscine à moins
d’être isolé de la piscine par une clôture, un mur ou
autre barrière permanente.

Esta bomba de calor deberá instalarse a una
distancia de al menos 5 pies (1.5 metros) de la pared
interior de la piscina; a menos que la bomba de calentar
esté separada de la piscina mediante una valla sólida de
5 pies (1.5 metros) de altura u otra barrera permanente.

2.2.3 Equipment Pad

Place the heat pump on a flat slightly pitched
surface, such as a concrete or fabricated slab (pad). This
allows proper drainage of condensation and rain water
from the base of the unit. If possible, the pad should be
placed at the same level or slightly higher than the filter
system equipment pad.

NOTE Ensure that the pad is pitched not more than ¼

inch per foot toward the compressor end (front)
of the heat pump. Pitch slab from back to front
¼ inch per foot maximum and level from side to
side.

2.2.4 Condensation and Drainage

Condensation will occur from the evaporator coil
while the unit is running and drain at a steady rate,
usually three to five gallons per hour, depending upon
ambient air temperature and humidity. The more humid
the ambient conditions, the more condensation will be
produced. The bottom of the unit acts as a tray to catch
rainwater and condensation. Keep the drain hole located
on the right side of the base of the unit clear of debris.

If the heat pump is installed indoor a means of
condensate disposal must be provided. The drain hole
in the base of the heat pump is tapped to fit an optional
5/8” diameter barbed adapter, Jandy p/n R3004100 (see
Section 9, “Replacement Parts”. If using the barbed
adapter, connect a length of 5/8” tubing or garden hose
to the adapter, then route it into a drain or outside the
building to dispose of the condensate. It is important

to remember that no part of the tubing or hose may be
above the level of the drain hole in the base of the heat
pump.

2.2.5 Lawn Sprinklers

Keep lawn sprinkler heads from spraying on the
heat pump to prevent corrosion and damage. Use a
deflector if needed.

2.2.6 Roof Run-off

Make sure the heat pump is not located where
large amounts of water may run-off from a roof into
the unit. Sharp sloping roofs without gutters will allow
massive amounts of rain water, mixed with debris from
the roof to be forced through the unit. A gutter or down
spout may be needed to protect the heat pump.

2.2.7 Installation of Anchor Clamps

In Florida, building codes require that the heat
pump be anchored to the equipment pad or platform
to withstand high wind pressures created during
hurricanes.

This heat pump was provided with anchor clamps
designed to hold the unit to the equipment pad in high
wind conditions. Installation of the anchor clamps is
recommended in all installations and are required in
Florida (reference Florida Building Code, Mechanical
Section 301.13).

To install the anchor clamps:

1. Be sure that the heat pump is in its permanent

location on the equipment pad.

2. Remove the anchor clamps from the installation

and instruction package.

NOTE Bolts and bolt anchors are not included with

the heat pump. Jandy recommends that a
3/16” x 1¾” long stainless steel Tapcon® type
concrete screw is used to mount the clamp
to the equipment pad. The Tapcon type
concrete screw meets Florida building code
requirements.

3. Place the clamps at the base of the heat pump in

the locations indicated in Figure 2.

Attach anchor clamps to
base of heat pump where
indicated by the arrows.

Page 7

Figure 3. Anchor Clamp Installation

6. Drill a hole in the cement using a masonry drill
bit, with a diameter as determined by the concrete
anchor, at each of the marks on the equipment pad.
The hole should be approximately 1-1/2” deep.

7. Insert a bolt anchor into each of the holes. Be sure
the anchors are set completely into the holes.

8. Position the anchor clamps so that the holes in the
clamps are over the bolt anchors. Be sure that the
clamp hooks are over the lip of the heat pump base
(see Figure 3).

Figure 2. Anchor Clamp Positions

4. Fit the hook of each clamp over the lip on the
base panel of the heat pump. The hook should
fi t between the lip of the base panel and the
evaporator coil guard (see Figure 3).

5. Mark the position of the hole in each clamp on the
equipment pad.

9. Insert an anchor bolt through each clamp into the
anchor and tighten to secure the clamp and heat
pump to the equipment pad.

Section 3. Water Connections

3.1 Plumbing Layout

Figure 4 illustrates the standard plumbing layout

with a single heat pump unit. Following the diagram
from right to left, the plumbing sequence is as follows:

Pool > Pool Pump > Filter > Heat Pump > Check
Valve > Chemical Loop > Chlorinator > Pool

NOTE For normal installations, do not install a shutoff

valve or any kind of variable restriction in the
water piping between the heat pump outlet and
the pool/spa.

Page 8

CHEMICAL LOOP
OR OPTIONAL CHLORINE
GENERATION SYSTEM
(JANDY AQUAPURE SHOWN)

Sensors

CHEMICAL FEEDER

e
r
u
P
a
u
q
A

TO POOL OR SPA

CHECK VALVE

Figure 4. Standard Plumbing Layout

The heat pump must be protected from back­siphoning of water. If there is any chance of back­siphoning, provide a check valve between the pool
and the filter pump inlet. Arrangement of pool system
components other than as illustrated in the preceding
and following diagrams can affect the operation of the
heat pump’s water pressure switch. Location of the heat
pump above or below the pool water surface can also
affect operation of the switch. In general, the pressure
switch can be adjusted to accommodate this effect if the
heat pump water connections are no more than six feet
below the pool water surface or no more than 15 feet
above it. See instructions for pressure switch adjustment
(Section 5.7) in the heat pump start-up section of this
manual for more information. If the heat pump is
installed outside of this range, an external flow switch
may need to be installed in the plumbing upstream of
the heat pump. Call the Jandy Heat Pump Technical
Service department at [phone] for details.

Be advised that when pool equipment is located
below the pool surface a leak can result in large scale
water loss or flooding. Jandy cannot be responsible for
such water loss or flooding or the damage caused by
either occurrence.

3.2 Water Connections at Heat Pump

Shipping plugs have been installed in the water
inlet and outlet ports of the heat pump at the factory.
Before installing any plumbing, remove the shipping
plugs. Filtered water is plumbed to the inlet, located on

the right side of the heat pump front panel. Heated water
flows through the outlet, located on the left side of the
heat pump front. Two inch unions are provided.

POOL HEATER

FILTER

POOL PUMP

FROM POOL OR SPA

MANUAL BYPASS VALVE

Plastic piping (PVC Schedule 40) should be
connected to the heat pump. The unions, provided with
the unit, accept 2” PVC pipe.

CAUTION

Make sure that fl ow requirements and pool
water turn over rates can be maintained with
the installation of additional heat pumps and
plumbing restrictions.

ATTENTION

Assurez-vous que la circulation d’eau requise
soit maintenue même si des pompes d’appoints
ou des éléments de plomberie, causant des
restrictions, sont ajoutés.

PRECAUCIÓN

Asegúrese de que los requerimientos de fl ujo
e índices de volumen de agua de la piscina
puedan mantenerse, con la instalación de
bombas de calentar adicionales y restricciones
de fontanería.

3.3 Check Valve Installation

The heat pump must be protected from back­siphoning of water. If there is any chance of back­siphoning, provide a check valve between the pool and
the filter pump inlet.

When an automatic chemical feeder is installed
in the plumbing, it must be installed downstream of the
heat pump. A check valve must be installed between
the heat pump and the chemical feeder to prevent back­siphoning of chemically saturated water into the heat
pump where it will damage the components.

Page 9

3.4 Automatic Flow Control Valve

The inlet/outlet header of the AE-Ti heat pump
comes equipped with an internal automatic flow control
valve. The automatic flow control valve maintains
the proper flow through the heat pump at rates up to
approximately 125 gpm (475 lpm). If the filter system
flow rate is higher than approximately 125 gpm (475
lpm), install a manual bypass valve (see Figure 4).

NOTE Be advised that if your circulation pump is

over 2 HP or if the total fl ow exceeds 125
gpm, you will have to add an external bypass
valve. Excess water fl ow will damage the heat

exchanger.

3.5 Multiple Unit Installation

3.5.1 Heat Pump and Heater Combination

In certain regions of the country it may be more
economical to run a heat pump during the warmer
months and a gas heater during the cooler months. In
some situations it may be desirable to run the heat pump
in the “Chiller” mode during the hottest portion of the
year and a heater during the cooler months. The Jandy
heat pump may be plumbed with a gas or electric heater
or any combination of heat sources including solar.
All heat sources must be plumbed in parallel to work
correctly and efficiently.

Figure 5 illustrates a recommended plumbing
layout for a heat pump / heater / solar combination
heating system for a pool / spa combination. Your
system may not contain all of these components, but the
basic plumbing will apply by eliminating the component
in the illustration that is not a part of your system.

3.5.2 Multiple Heat Pump Connections

All plumbing on multiple heat pump installations
must be done in parallel (see Figures 6 through 9). An
equal flow of water to each heat pump is important for
optimum operation.

NOTE It may be necessary to adjust water pressure

switch if a unit is installed below the water level.
See Section 5.7 for details on when and how to
adjust the pressure switch.

NOTE Each heat pump allows a maximum fl ow rate of

125 gpm and requires a minimum of 30 gpm.

POOL
INTAKE

SPA
INTAKE

POOL
RETURN

SPA
RETURN

SPA
DRAIN

CHECK
VALVE

POOL
DRAIN

SPA
MAKE-UP

FILTER

HEATER

FILTER
PUMP

CHECK
VALVE

HEAT PUMP

FROM SOLAR

TO SOLAR

Figure 5. Plumbing For Heating System Combinations

Page 10

Extend 12" past
end heater inlet
for hydraulic
balancing

Flow Meter

To Pool

Figure 6. Two Heat Pump Plumbing Layout

12 inches min. clearence around evap.

12"

2" pvc

OPTIONAL

2" Gate Valve Bypass

Minimum 2" pvc
pipe

2" pvc

NOTE! Gate Valves are
optional on heater inlets
but will help system
balancing

Extend 12" past
end heater inlet
for hydraulic
balancing

Flow Meter

2" pvc pipe

Pool pump

Extend 12" past
end heater inlet
for hydraulic
balancing

To Pool

2" pvc

3" pvc pipe

3" pvc pipe

Flow Meter

12 inches min. clearance around evap.

12"

2" pvc

2" pvc

3" pvc pipe

3" Gate Valve Bypass

Minimum 3" pvc
pipe

NOTE! Gate Valves are
optional on heater inlets
but will help for system
balancing

2" pvc

Extend 12" past
end heater inlet
for hydraulic
balancing

Flow Meter

3" pvc pipe

Pool pump

Figure 7. Four Heat Pump Plumbing Layout

Page 11

12 inches min. clearance around evap.

FLOW METER

EXTEND 16 TO 20" PAST END
HEATERS INLET FOR HYDRAULIC
BALANCING

2" pvc

FLOW METER

2" pvc

FLOW METER

4"PVC PIPE

FLOW METER

TO POOL

Figure 8. Six Heat Pump Plumbing Layout

2" pvc

FLOW METER

4" GATE VALVE BYPASS

12"

NOTE! GATE VALVES
ARE REQUIRED ON
HEATER INLETS TO
HELP SYSTEM
BALANCING

2" pvc

FLOW METER

4"PVC PIPE

2" pvc

FLOW METER

2" pvc

EXTEND 16 TO 20" PAST END
HEATERS INLET FOR HYDRAULIC
BALANCING

POOL PUMP

MINIMUM 4"PVC PIPE

EXTEND 16 TO 20" PAST END
HEATERS INLET FOR HYDRAULIC

2"

pvc

BALANCING

4"pvc

FLOW METER

FLOW METER

2"

pvc

NOTE! GATE VALVES
ARE REQUIRED ON
HEATER INLETS TO
HELP SYSTEM
BALANCING

BALANCING VALVES

2"

FLOW METER

FLOW METER

pvc

EXTEND 16 TO 20" PAST END
HEATERS INLET FOR HYDRAULIC
BALANCING

6" PVC

6" PVC

2"

pvc

FLOW METER

GATE VALVE BYPASS

12 inches min. clearance around evap.

TO POOL

MINIMUM 6"PVC PIPE

Figure 9. Eight Heat Pump Plumbing Layout (Dual Headers)

EXTEND 16 TO 20" PAST END
HEATERS INLET FOR HYDRAULIC
BALANCING

4"pvc

POOL PUMP

2"

pvc

FLOW METER

2"

pvc

FLOW METER

2"

pvc

FLOW METER

2"

pvc

EXTEND 16 TO 20" PAST END
HEATERS INLET FOR HYDRAULIC
BALANCING

12 inches min. clearance around evap.

Page 12

Section 4. Electrical Connections

WARNING

ELECTRICAL SHOCK HAZARD. This heat

pump contains wiring that carries high voltage.
Contact with these wires may result in severe
injury or death. Disconnect power circuit before
connecting the heat pump

AVERTISSEMENT

POSSIBILITÉ DE CHOCS ÉLECTRIQUES.

Ce système de chauffage contient du fi lage
de haut voltage. Un contact avec ces fi ls peut
résulter en des blessures sérieuses ou la mort.
Débranchez le circuit de puissance avant de
relier la pompe à chaleur

AVISO

PELIGRO DE DESCARGA ELÉCTRICA.

Esta bomba de calor, contiene cableado
de alta tensión. El contacto con los cables
podría ocasionar lesiones graves o la muerte.
Desconecte el circuito de alimentación, antes
de conectar la bomba de calentar.

4.1 General Information

Wiring connections must be made exactly as
shown in the wiring diagram found on the inside of the
heat pump access panel (see Figure 10 for single phase
electrical wiring and Figure 11 for 3-phase electrical
wiring). The heat pump must include a definite means
of grounding and bonding. There is a bonding lug on the
right side of the heat pump, where a bond wire must be
attached.

CAUTION

Label all wires prior to disconnection when
servicing controls. Wiring errors can cause
improper and dangerous operation. Verify
proper operation after servicing.

ATTENTION

Au moment de l’entretien des commandes,
étiquetez tous les fi ls avant de les débrancher.
Des erreurs de câblage peuvent entraîner un
fonctionnement inadéquat et dangereux.

PRECAUCIÓN

Proceda a etiquetar todos los cables antes
de su desconexión en los controles de
mantenimiento. Los errores de cableado
pueden ocasionar un funcionamiento
peligroso e inadecuado. Comprobar que el
funcionamiento es correcto, una vez efectuado
el mantenimiento.

COMPRESSOR

S

M

CAPACITOR

Page 13

LOAD 1 TO PUMP TIME CLOCK

BR

AUTO-HEAT

CONTACTOR

W

BL

BK

BK

BK

R

W

O

W

MAIN

CONTACTOR

BK

LOAD 2 TO PUMP TIME CLOCK

LINE 2 FROM PUMP TIME CLOCK

LINE 1 FROM PUMP TIME CLOCK

O

Y

O

BK

BK

LINE 1

LINE 2

GROUND

HIGH PRESSURE

SWITCH

R

BK

CRANKCASE

HTR.

OPTIONAL

MODEL
AE3000

ONLY

BK

BK

COMPRESSOR

FAN CAPACITOR

BR/W

R

W

BR

Y

BR

FAN MOTOR

OPTIONAL

REVERSING SOLENOID

HEAT / COOL

JVA
ACTUATOR
PLUGS

BK

W

14151617

J-2HARNESSCONNECTION

W/V

BK/R

W/BR

W

W

BK/W

BKBK

BR

13

BK/BR

RRW

12

BK

PRIMARY (230 VAC)

TRANSFORMER

SECONDARY (24 VAC)

BL

BR

W

BK

11

910

W

BL

BK/G

WATER

SENSOR

BK

BK

Fan

T-8

T-7

DigitalControl

J-2

OR

Y

RBLBLYY

8

J-1HARNESSCONNECTION

O

BK

W/GY

AIR

SENSOR

BL

BL

H20

T-1

T-2

J-1

O

LOW PRESSURE

SWITCH

Com

NO3
NC2

WATER PRESSURE

SWITCH

W

RBL

O

3

Y

BK

Remote

T-6 T-5

1

2

W/R

R

W

A

4567

V

GY

R

R

Air

T-4

T-3

AE SERIE

208/230 VAC

60 Hz

SINGLE PHASE

WIRING DIAGRA

FACTORY WIRED HIGH VOLTAGE

FIELD SUPPLIED HIGH VOLTAGE

FACTORY WIRED

MULTICONDUCTOR CABLE

FACTORY WIRED LOW VOLTAGE

FACTORY WIRED OPTIONAL
COMPONENT LOW VOLTAGE

FACTORY WIRED OPTIONAL
COMPONENT HIGH VOLTAGE

BK - BLACK
BK/BR - BLACK WITH

BROWN TRACE

BK/G -BLACK WITH

GREEN TRACE

BK/R - BLACK WITH

RED TRACE

BK/W - BLACK WITH

WHITE TRACE
BL - BLUE
BR -BROWN
BR/W - BROWN WITH

WHITE TRACE
GY - GRAY
O - ORANGE
R - RED
V - VIOLET
W - WHITE
W/BR - WHITE WITH

W/GY -WHITE WITH

W/R - WHITE WITH

W/V - WHITE WITH

Y - YELLOW

BROWN TRACE

GRAY TRACE

RED TRACE

VIOLET TRACE

H3000200A

Figure 10. AE-Ti Single-Phase Electrical Supply Wiring Diagram

Page 14

COMPRESSOR

FAN CAPACITOR

BR/W

BR

Y

BR

FAN MOTOR

BK

R

W

OPTIONAL

REVERSING SOLENOID

HEAT / COOL

JVA
ACTUATOR
PLUGS

BK

W

W

14151617

J-2HARNESSCONNECTION

W/V

BK/R

W/BR

LOAD 3 TO PUMP TIME CLOCK

LOAD 1 TO PUMP TIME CLOCK

BR

24V

LINE 1 FROM

L1

PUMP TIME CLOCK

L2

LINE 3 FROM

L3

PUMP TIME CLOCK

24V

BL

L1

L2

MAIN

L3

CONTACTOR

Y

BR

BK

8

910

W

BK

BK/G

WATER

SENSOR

BL

BK

Fan

T-7

T-1

DigitalControl

J-2

W

W

BK/W

BK

R

W

BKBK

13

BR

T1

T2

T3

BK/BR

AUTO-HEAT

CONTACTOR

T1

T2

T3

BK

PRIMARY (230 VAC)

TRANSFORMER

SECONDARY (24 VAC)

BL

W

BR

RRW

11

12

BL

BK

T-8

O

BK

Y

O

W

24V

24V

O

RBLBLYY

BK

O

R

W

BK

BK

BK

4567

J-1HARNESSCONNECTION

W/GY

AIR

SENSOR

BL

T-2

J-1

V

GY

R

R

Air

T-4

T-3

O

H20

CRANKCASE

BK

O

RBL

W

3

2

Y

BK

Remote

T-6 T-5

A

R

HTR.

OPTIONAL

MODEL
AE3000

ONLY

BK

HIGH PRESSURE

SWITCH

R

O

LOW PRESSURE

SWITCH

NO3
NC2

WATER PRESSURE

SWITCH

O

1

W/R

W

Com

3-PHASE MONITOR

BK

C

Y

Y

BR

Y-OUT

L3

L2

ON FAULT

CUT WIRE

FOR 50Hz

L1

LINE 1

LINE 2

LINE 3

GROUND

AE SERIES

208/230 VAC

60 Hz

3 - PHASE

WIRING DIAGRAM

FACTORY WIRED HIGH VOLTAGE

FIELD SUPPLIED HIGH VOLTAGE

FACTORY WIRED

MULTICONDUCTOR CABLE

FACTORY WIRED LOW VOLTAGE

FACTORY WIRED OPTIONAL
COMPONENT LOW VOLTAGE

FACTORY WIRED OPTIONAL

COMPONENT HIGH VOLTAGE

BK - BLACK
BK/BR - BLACK WITH

BROWN TRACE

BK/G - BLACK WITH

GREEN TRACE

BK/R - BLACK WITH

RED TRACE

BK/W - BLACK WITH

WHITE TRACE
BL - BLUE
BR -BROWN
BR/W -BROWN WITH

WHITE TRACE
GY - GRAY
O - ORANGE
R - RED
V -VIOLET
W - WHITE
W/BR -WHITE WITH

BROWN TRACE

W/GY - WHITE WITH

GRAY TRACE

W/R - WHITE WITH

RED TRACE

W/V - WHITE WITH

VIOLET TRACE
Y -YELLOW

W

R

BK

H3000300A

Figure 11. AE-Ti 3-Phase Electrical Supply Wiring Diagram

Page 15

4.2 Main Power

Electrical wiring to the heat pump must be in
accordance with the latest edition of the National
Electric Code (NEC), ANSI/National Fire Protection
Association (NFPA) 70 in the United States, and in
Canada, the Canadian Electrical Code (CEC) C22.1,
unless local code requirements indicate otherwise.

The heat pumps come factory-wired intended for
use with either 208/230 VAC, 60 Hz field electrical
supply depending on the model. See the rating plate for
the electrical specifications. All wiring must be done by
a certified electrician.

The following is the procedure to wire the AE-Ti
to the electrical source specified on the Rating Plate:

1. Be sure the power to the circuit for the heat pump

is turned off.

2. Remove the 5 screws that attach the service/access

panel to the heat pump unit (see Figure 12).

3. Electrical supply lines must be run through

watertight conduit. Run the wires and conduit from

the power source and connect them to the conduit

connection labeled “High Voltage Connection” on

the right side of the heat pump. See Figure 12 for

connection location.

4. Connect the wires to the terminals on the main

contactor as shown in the wiring diagram.

5. Connect the ground wire to the ground lug

provided in the electrical compartment.

6. Replace the service access panel and replace the
screws to hold it in place.

7. Connect a copper bonding wire (8 AWG) to the
bonding lug on the right side of the heat pump.

4.3 Bonding

CAUTION

This heater must be connected to a bonding
grid with a solid copper wire not smaller in
diameter than 8 ga.

ATTENTION

L’appareil de chauffage doit être connecté à
une grille de mise à la terre par un fi l de cuivre
d’un diamètre de calibre minimal 8.

PRECAUCIÓN

Esta bomba de calor deberá estar conectado
a una rejilla de unión con hilo de cobre sólido,
de un diámetro no inferior a 8 ga.

The National Electrical Code and most other

codes require that all metallic components of a pool
structure, including reinforcing steel, metal fittings,
and above ground equipment be bonded together with
a solid copper conductor not smaller than 8 AWG. The
heat pump, along with pumps and other pool equipment
must be connected to this bonding grid. A bonding lug
is provided on the right hand side of the heat pump to
ensure this requirement is met.

SERVICE ACCESS
PANEL (5 SCREWS)

Figure 12. AE-Ti Heat Pump Front View

PORT FOR TIME
CLOCK OVERRIDE
WIRES

PORT FOR HIGH
VOLTAGE WIRES

PORT FOR LOW
VOLTAGE WIRES

Page 16

4.4 Pump Connection (Auto-Heat
Feature)

(Residential only) When connecting the time
clock override parallel circuit, proper phasing must
be maintained. Use 12 AWG wire. Follow the wiring
diagram on the service access panel of your heat pump,
referring to the auto-contactor section (see Figures 10
and ll on pages 13 and 14). The use of four different
color wires will help in maintaining the proper phasing
to and from the pool pump time clock.

4.5 Optional Remote Controls

Electrical wiring must be in accordance with
the latest edition of the NEC (NFPA 70) in the United
States and CEC (CSA 22.1) in Canada, unless local
code requirements indicate otherwise. To connect
remote control equipment to the heat pump, perform the
following steps:

1. Turn off the power to both the pool/spa control

system and the heat pump unit.

2. Remove the 5 screws that attach the service/access

panel to the heat pump unit (see Figure 12 on

page 15). This will allow you to access the wires

from the AE-Ti control panel for the remote

control installation (see Figure 13).

3. Run the wires from the pool/spa control system

into the conduit connection labeled “Low Voltage

Connection”, located on the lower right hand side

of the heat pump (see Figures 12 and 14).

4. Strip approximately 1/4” of insulation from the

heat pump remote control wires (black and white,

see Figure 14).

5. Using wire nuts, connect the wiring from the

pool/spa control system to the heat pump remote

control wires.

6. Restore power to the heat pump and the pool/spa

control system.

NOTE For AquaSwitch® or three wire remote controls,

connect the HIGH and COMMON wires to the
heat pump remote control wires.

4.5.1 Connection to an AquaLink RS
Control System

1. Install a fi xed resistor, with a value of 2.2K Ohms,
in the solar sensor terminals #3 and #4 of the
green, 10-pin terminal bar of the AquaLink RS
Power Center (see Figure 15).

Figure 13. AE-Ti Control Panel, Interior View

Black and White Wires for
Remote Control

Figure 14. AE-Ti Control Panel - Remote Control

Wiring

Run Wires from
Pool/Spa System
through Low
Voltage Conduit.

2.2K Ohms Resistor
in Solar Sensor
Terminals for Heat
Pump/Chiller

Gas Heater Connections
Terminals 1 and 2

Page 17

To Pressure
Switch

Green- Enabled
Red- On

4321 654321

LED
will not
come on
for Heat
Pump

Heat Pump/Chiller #1

Port for Low
Voltage Wires

Service/Wiring
Cover Panel

10987654321

Standard
High
Voltage
Relay

Figure 15. AquaLink RS to AE-Ti Heat Pump/Chiller Wiring

Battery
(9Volt)

Low Voltage
Wiring to Low
Voltage Port
on Heat Pump

Fireman's
Switch

From Fusible
Link

Heat Pump/Chiller #2

Port for Low
Voltage Wires

Gas Heater

Service/Wiring
Cover Panel

NOTE One end of the wiring reserved to run into

the conduit connection labeled “Low Voltage
Connection”, located on the lower right hand
side of the heat pump (see Figures 12 and 14).

2. Run the wires from the Heat Pump control panel
through the wiring conduit located on the outer
right hand side of the Heat Pump.

3. In the AquaLink Power Center, connect the Heat
Pump to a standard relay, then connect the relay
to the solar pump output on the PCB. Set the time
to 11:59 PM; at 12:00 AM, the AquaLink RS
will auto-relabel Solar as Heat Pump. Otherwise,
the AquaLink RS will auto-relabel Solar as Heat
Pump within 24 hours.

4. The Solar Button will activate the heat pump/
chiller and the Pool and/or Spa Heater Buttons will
activate the gas heater. In this manner the pool or
spa can be heated or chilled by the heat pump, the
gas heater or both.

Page 18

Section 5. Operation

CAUTION

Do not use this heat pump if any part has
been under water. Immediately call a qualifi ed
service technician to inspect the heater and
replace any part of the control system which
has been under water.

ATTENTION

N’utilisez pas cet appareil s’il a été plongé
dans l’eau, même partiellement. Faites
inspecter l’appareil par un technicien qualifi é et
remplacez toute partie du système de contrôle
et toute commande qui ont été plongés dans
l’eau.

PRECAUCIÓN

No utilice esta bomba de calor si algunos de
sus componentes han estado debajo del agua.
Póngase inmediatamente en contacto con un
técnico de mantenimiento cualifi cado para que
inspeccione el equipo y reemplace cualquier
parte del sistema de control que haya estado
debajo del agua.

CAUTION

Keep all objects off the top of the heat pump.
Blocking air fl ow could damage the unit and
may void the warranty.

Be sure that there is water in the pool and that the
surface level is above the skimmer or other inlet of the
pool’s filter system.

With any new pool or spa installation, operate
the filter pump with the heat pump off long enough
to completely clean the water. This will remove any
installation residue from the water. Clean the filter at
the end of this operation before starting the heat pump.
When raising the temperature of a cold pool, program
the time clock to run the pump continuously. This lets
the filter system and heat pump operate continuously
until the water reaches the temperature setting on the
temperature control. When that happens, the heat pump
will automatically shut off, but the filter pump will keep
running.

5.2 Operating the Controller

Your new AE-Ti heat pump is controlled by an
advanced microprocessor based controller that provides
a sophisticated yet simple interface to operate your heat
pump for maximum efficiency and enjoyment of your
pool. To locate the control buttons, see Figure 16.

5.2.1 Off/On Button

When the control panel is turned off, the screen
displays CONTROL IS OFF and the Off/On LED
indicator is not lit. Press
panel. The LED will light and the display will read

PLEASE SELECT POOL OR SPA.

5.2.2 Pool Mode - (Normal Heat)

Off/On to turn on the control

ATTENTION

Ne posez aucun objet sur le dessus de
l’appareil. Il pourrait empêcher la circulation de
l’air, ce qui risquerait d’endommager l’appareil
et d’annuler la garantie.

PRECAUCIÓN

Mantenga todos los objetos fuera de la parte
superior de la bomba de calor. La obstrucción
del fl ujo de aire podría dañar la unidad y
anular la garantía.

5.1 Initial Start-up Precautions

ATTENTION

After starting the AE-Ti heat pump, please
note that there is a 5 minute delay before the
compressor begins operation. The heat pump
display will show the remaining delay time in
minutes.

To enable the pool mode, press POOL. The LED
indicator will light and the unit will display

TEMPERATURE SET-POINT = XX°

NOTE XX represents the current temperature setting

on the control. The default setting for pool
temperature is 82°F.

POOL

for 5 seconds.

After 5 seconds the unit will display POOL →

HEAT and the current pool temperature. You can

change the temperature set point by pressing the

Down button. The display will change back to

or

Up

show POOL TEMPERATURE SET-POINT = XX°.

Repeatedly press the Up or Down

button until you
reach the desired temperature set point. After 5 seconds
of inactivity, the new set point is stored in memory.
When the water temperature falls to 1 degree below

the temperature setting

and after a 5- minute delay, the

control will start the heat pump.

Page 19

Figure 16. Main Control Panel

5.2.3 Pool Mode - (Optional Auto Heat)

If connected, the Auto-Heat mode allows the
heat pump to monitor the temperature of the water 24
hours a day by turning the pool pump on and sampling
the water temperature. When the water temperature
drops below the programmed temperature set point, the
control will start the heat pump.

To operate in pool mode with the Heat Auto­Run feature, press

POOL, then press Time/Auto. The

LED indicators on both buttons will light and the unit
will display POOL TEMPERATURE SET-POINT =

XX°

for 5 seconds. Change the temperature set point

by pressing the

Up or Down buttons until the desired

set point is displayed. After 5 seconds of inactivity the
unit will display

POOL →AUTO-HEAT along with the

current pool temperature and the delay time remaining
until the heat pump starts.

5.2.4 Spa Mode - (Optional Auto Heat)

If connected, the spa mode automatically enables
the Auto-Run feature. Press SPA to enable spa mode.
The LED indicator will light and the unit will display

SPA TEMPERATURE SET-POINT = XX° for 5

seconds. Change the temperature set point by pressing
the Up or Down buttons until the desired set point is
displayed. After 5 seconds of inactivity the display will
read SPA AUTO-HEAT along with the current spa
temperature and the delay time left until the heat pump
starts. Additionally, the new set point will be stored in
memory. The default factory setting for Spa temperature
is 104 degrees.

5.2.5 Keypad Lockout

To lockout the keypad in any operating mode,

press and hold the POOL, SPA, and Heat/Cool buttons
for 6 seconds. All control buttons will be disabled and
the control will operate in the mode it was in when the
keypad lockout occurred. If any button is pressed when
the keypad is in lockout mode, the unit will display

SYSTEM LOCKED for 5 seconds. To unlock the

keypad, press and hold the
buttons for 6 seconds. The unit will display

UNLOCKED

.

POOL, SPA, and Heat/Cool

SYSTEM

5.2.6 Feature Lockout

To lockout all features except the On/Off, POOL

SPA buttons in any operating mode, press and

and
hold the Time/Auto, Heat/Cool and Down buttons
for 6 seconds. All control buttons except the On/Off,

POOL

and SPA will be disabled. If any button is

pressed when the keypad is in feature lockout mode, the
unit will display FEATURE LOCKED for 5 seconds.
To unlock the keypad, press and hold the Time/Auto,

Heat/Cool

and Down buttons for 6 seconds. The unit

will display FEATURE UNLOCKED.

Page 20

5.3 Operating Features of Units with
Optional Chiller

5.3.1 Pool Mode - (Normal Cool)

To operate in Pool-Cool mode, press POOL. The

LED indicator will light and the unit will display the
message
for 5 seconds.

HEAT and the current pool temperature. Press Heat­Cool
SET-POINT = XX°

set point by pressing the Up or Down buttons until
the desired set point is displayed. After 5 seconds of
inactivity, the display will read
with the current pool temperature and the delay time
remaining until the chiller starts. Additionally, the new
set point will be stored in memory. When the water
temperature rises to 1 degree above the temperature

setting
will turn on the chiller circuit.

the temperature of the water 24 hours a day. When
the temperature of the water rises above the desired
temperature setting, the control will then energize the
unit.

Run feature, press
light and the unit will display the message POOL

TEMPERATURE SET-POINT = XX°

HEAT and the current pool temperature. Press Heat­Cool
SET-POINT = XX°

button will light. The display will read POOL→COOL
along with the current pool temperature and the delay
time remaining until the chiller starts.

TEMPERATURE SET-POINT = XX°

and the LED on the button will light. Change the setting
using the Up or Down buttons until you reach the
desired set point. After 5 seconds of inactivity, the unit
will display POOL →AUTO-COOL and the current
pool temperature.

indicator will light on the SPA and the Time/Auto
buttons and unit will display SPA TEMPERATURE

SET-POINT = XX°

using the Up or Down buttons until you reach the

POOL TEMPERATURE SET-POINT = XX°

After 5 seconds the display will read POOL →

. The unit will display POOL TEMPERATURE

for 5 seconds. You can change the

POOL-COOL along

and after a time delay of 5 minutes, the control

5.3.2 Pool Mode - (Auto Cool)

The Auto-Cool mode allows the unit to monitor

To operate in pool mode with the Cooling Auto-

POOL. The LED indicator will

for 5 seconds.

After 5 seconds the display will read POOL →

. The unit will display POOL TEMPERATURE

for 5 seconds and the LED on the

Press Time-Auto. The unit will display POOL

for 5 seconds

5.3.3 Spa Mode - (Auto Cool)

To operate in Spa Cool mode press SPA. The LED

for 5 seconds. Change the setting

desired set point. After 5 seconds of inactivity the
display will read

SPA AUTO-HEAT along with the

current spa temperature and the delay time left until
the chiller starts. Additionally, the new set point will be
stored in memory.

Heat/Cool. The Heat/Cool LED will light

Press

and the display will read SPA TEMPERATURE SET-

POINT = XX°

the

Up or Down buttons until you reach the desired set

point. The display will read

for 5 seconds. Change the setting using

SPA AUTO-COOL along

with the current water temperature after 5 seconds of
inactivity. The new set point will be stored in memory.

5.4 Enabling Remote Control with
AquaSwitch Systems and All Other
Dual TStat Remote Systems

NOTE Temperature setting for Pool or Spa are set at

the heat pump.

1. Turn off the control panel.

2. Press and hold the

Time/Auto, Up and Down

arrow buttons for 5 seconds to enter the setup
menu. The control panel will momentarily display

SETTING 01 then it will display the language that

is used for the display.

NOTE In this mode, pressing and releasing the SPA

button will step though each setting in the setup
menu. Each press of the SPA button will cause
the display to momentarily show the setting
number then show the value for that setting.
Pause between button presses to allow the
control time to respond.

3. Repeatedly press and release the SPA button until

the display momentarily reads
control panel will then display

DISABLED.

SETTING 05. The

AQUASWITCH

4. Press the Up arrow button one time to enable

remote control of the unit. The control panel will
then display

AQUASWITCH ENABLED.

5. Press and hold the Time/Auto, Up and Down

arrow buttons for 5 seconds to exit the setup menu.

5.5 Enabling Remote Control with
AquaLink RS Systems

NOTE Temperature setting for Pool or Spa are set at

the Aqualink RS indoor controller.

1. Turn off the control panel.

Page 21

2. Press and hold the Time/Auto, Up, and Down

arrow buttons for 5 seconds to enter the setup
menu. The control panel will momentarily display

SETTING 01 then it will display the language that

is used for the display.

NOTE In this mode, pressing and releasing the SPA

button will step though each setting in the setup
menu. Each press of the SPA button will cause
the display to momentarily show the setting
number then show the value for that setting.
Pause between button presses to allow the

control time to respond.

3. Repeatedly press and release the SPA button until

the display reads
will then display

4. Press the

Up arrow button one time to enable

SETTING 13. The control panel

AQUALINK DISABLED.

remote control of the unit. The control panel will
then display

AQUALINK ENABLED.

5. Press and hold the Time/Auto, Up and Down

arrow buttons for 5 seconds to exit the setup menu.

5.6 Advanced Digital Microprocessor
Quick Guide

To operate your heat pump, simply select, then
press the buttons corresponding to the operating mode
you want to use. The associated LED indicator will
light.

1. Press

2. Select

3. The heat pump will run consistent with pool time

4. The optional Heat/Cool feature is used with

Off/On to turn heat pump on or off.

POOL or SPA. The heat pump control

panel will display the current pool or spa

temperature setting. Adjust the temperature set

point up or down as desired.

clock for the pump. Press

Time/Auto to enable

the optional Auto-Heat. The heat pump will

override the time clock and maintain/monitor the

pool temperature 24 hours a day. To maintain the

temperature, the heat pump will turn on at night.

Reverse Cycle equipped heat pumps. Press Heat/

Cool

to reverse roles from heating to cooling the

pool to the desired temperature.

5.7 Water Pressure Switch Adjustment

CAUTION

The water pressure switch should be
adjusted to turn the heater off when the
pump is off. Setting the switch to close at
too low of a fl ow can damage the appliance.
Adjust the switch to turn the heater off, not
on.

ATTENTION

Le manocontact de pression d’eau doit être
réglé de façon à ce que l’appareil cesse
de fonctionner si la pompe s’arrête. Si
le manocontact est réglé pour se fermer
lorsque le débit d’eau est trop faible,
l’appareil risque de s’endommager. Réglez
le manocontact pour qu’il arrête l’appareil, et
non pour qu’il le mette en marche.

PRECAUCIÓN

El interruptor de la presión del agua, deberá
ajustarse de forma que el calentador se apague
cuando se apague la bomba. La calibración del
interruptor para que pueda apagarse con fl ujos
demasiado bajos podría estropear el equipo.
Ajuste el interruptor para apagar el calentador,
no para encenderlo.

The pressure switch is preset at the factory for
activation at 2 psi (14 kPa). This is the minimum
setting for the water pressure switch and works for
all basic installations as shown previously in Section

3.1 and Section 3.5 in this manual. Only adjust the
water pressure switch if the heat pump does not
operate when the proper flow is applied to unit or if
the heat pump does not shut off when the filter pump
is off. Occasionally, unusual plumbing configurations
or necessary restrictions in the plumbing may cause
pressure sensing problems. In these rare situations, the
plumbing system configuration may require adjustment
of the water pressure switch.

Adjustment of the pressure switch may be
necessary if any part of the filter system piping is 3 feet
(0.91 m) or more above the top of the heat pump jacket.

Do not adjust the pressure switch if the heat pump
is installed more than 15 feet (4.57 m) above or 6 feet
(1.83 m) below the pool surface. Consult your local
Jandy representative for recommendations.

Page 22

On some installations, the piping from the heat
pump to the pool is very short. The back pressure
could be too low to trigger the pressure switch. If this
happens, it may be necessary to install a directional
fitting or elbows where the return line enters the
pool. This will increase back pressure enough for the
heat pump to operate properly. If this configuration
is necessary, be sure to check that the system flow is
above the minimum requirement of 30 gpm after the
direction fitting or elbow has been installed.

Make sure the pool filter is clean before making
any pressure switch adjustment: A dirty filter will
restrict the water flow and the pressure switch cannot be
adjusted properly.

To adjust the pressure switch:

1. Be sure that all valves in the system are set to

allow water fl ow through the heat pump. Start the

fi lter pump.

2. Set the heat pump control to call for heat. Set the

On/Off switch on the heat pump control to the

ON position. If the heat pump was installed with

the Auto-Heat feature, set the mode to TIME so

that the heat pump will turn on if water is fl owing

through the heat exchanger.

3. If the heat pump control displays “LOW H

O

2

FLOW”, then the fl ow in the system may be below

the minimum fl ow of 30 gpm needed for the safe

operation of the heat pump. Investigate and correct

any fl ow problems before adjusting the water

pressure switch.

4. Remove the heat pump’s control access panel. The

water pressure switch is located in the lower left

corner of the control compartment.

5. After confi rming the fl ow rate is at a minimum

of 30 gpm, slowly rotate the thumb wheel on

the water pressure switch in a counterclockwise

direction until the “LOW H2O FLOW” indicator

disappears from the control display. Remember

that there is a time delay before the heat pump

compressor will start.

6. Once the heat pump is running, turn off the fi lter

pump. The heat pump should turn off immediately.

7. If the heat pump continues to operate when the

fi lter pump is off, turn the thumb wheel on the

water pressure switch in a clockwise direction

until “LOW H

O FLOW” is displayed on the

2

control and the heat pump shuts down.

8. Check the setting of the water pressure switch by
starting and stopping the fi lter pump and checking
the control display and operation of the heater
between each fl ow change.

9. If the water pressure switch cannot be adjusted
to accommodate the conditions listed above,
an external fl ow switch must be added to the
plumbing system to ensure that the heat pump will
not operate without the proper fl ow through the
heat exchanger.

Section 6. General Maintenance

6.1 Water Chemistry

Proper chemical balances are necessary for

sanitary bathing conditions as well as ensuring your heat
pump’s long life. Be sure to keep your chemical and
mineral concentration levels within the values indicated
in Table 2.

NOTE For spas, it is also necessary to perform water

changes in addition to chemical treatment. It is
recommended to change the spa water every
60 days for light usage and every 30 days if
usage is heavy.

6.2 Winterizing

CAUTION

Failure to winterize could cause damage to the
heat pump and will void the warranty.

ATTENTION

La garantie sera annulée si l’appareil n’est pas
hivernisé convenablement.

PRECAUCIÓN

La falta de acondicionamiento de la bomba de
calor para el invierno podía causar daños y
anular la garantía.

In areas where freezing temperatures occur, you

should protect your pump, filter, and heat pump from
the elements. Perform the following steps to completely
drain the heat pump (see Figure 17).

1. Turn off the electrical power to the heat pump at
the main breaker panel.

2. Shut off the water supply to the heat pump.

3. Disconnect the water inlet and outlet unions
located on the lower front panel of the heat pump.

Page 23

Table 2. Optimal Water Chemistry Ranges

Test Recommended Level

Free Chlorine or 1.0 to 3.0 ppm (3.0 to 5.0 spa)

Bromine 2.0 to 4.0 ppm (3.0 to 5.0 spa)

pH 7.4 to 7.6

Total Alkalinity (TA) 80 to 120 ppm

Calcium Hardness (CH) 200 to 400 ppm

Cyanuric Acid 30 to 50 ppm

Total Dissolved Solids (TDS) Less than 2000 ppm

Copper 0 ppm

* Concentration levels taken from “Basic Pool and Spa Technology” published by NSPI (National Spa and Pool
Institute).

Water Inlet Union

Water Outlet Union

Figure 17. Winterizing the AE-Ti Heat Pump

4. Open the drain located on the lower front panel of
the heat pump to drain the remaining water from
the heat exchanger. Leave the drain open until the
unit is ready for seasonal start-up.

5. Cover only the top of the heat pump to prevent
debris from falling into the unit. Do not wrap the
sides of the heat pump with any plastic or other
material that will retain heat or moisture inside the
unit.

6.3 Spring Start-Up

If your heat pump has been winterized, perform

the following steps when starting the system in the
Spring:

1. Uncover the heat pump and inspect the top and
sides for any debris or structural problems.

2. Close the petcock located on the lower front panel
of the heat pump.

Petcock
(Leave open until unit
is ready to start-up)

4. Turn on the fi lter pump to supply water to the
heat pump. Circulate water through the system
long enough to cycle all of the pool water through
the fi lter. Check for leaks in and around the heat
pump.

5. Turn on the electrical power to the heat pump at
the main breaker panel.

6.4 Inspection and Service

Jandy Heat Pumps are designed and constructed

to provide long performance life when installed and
operated properly under normal conditions. Periodic
inspections are important to keep your heat pump
running safely and efficiently through the years.

6.4.1 Owner Inspection

Jandy recommends that you inspect your heat

pump on a continual basis and especially after abnormal
weather conditions. The following basic guidelines are
suggested for your inspection:

3. Connect the water inlet and outlet unions located
on the lower front panel of the heat pump.

1. Keep the top and surrounding areas of the heat
pump clear of all debris.

Page 24

2. Keep all plants and shrubs trimmed and away from
the heat pump.

3. Do not use this heat pump if any part has been
under water. Immediately call a qualifi ed
professional technician to inspect the heat pump
and replace any part of the control system which
has been submerged.

The heat pump will produce condensation (water)

while in operation. The heat pump base is designed to
allow the condensation to exit through the bottom drain
port when the unit is running. The condensation will
increase as the outdoor air humidity level increases.
Check the following at regular intervals to ensure proper
condensate drainage:

1. Visually inspect and clear the bottom drain ports
of any debris that could clog the ports.

2. Ensure that condensate water does not puddle
inside the heat pump

3. Ensure that condensate run-off is properly directed
away from the equipment pad to keep it from
undermining the pad.

During normal operation, the heat pump

produces three to five gallons of condensate per hour.
If condensate drainage is above this range during
operation or if water continues to drain from the base
when the heat pump is not in operation for more than an
hour, a leak in the internal plumbing may have occurred.
Call a qualified heat pump technician to investigate the
problem.

Keep the top air flow discharge and air flow intake

area clear of debris so the air flow though the heat pump
is not restricted. The cooler discharge air from the top
should not accumulate and be drawn into the side air
intake coils. Keep all plants and shrubs trimmed away
from the heat pump.

Make sure the front of the unit is accessible for

future service.

Keep lawn sprinkler heads from spraying on the

heat pump to prevent corrosion and damage. Use a
deflector if needed.

If the unit is installed under a very sharp roof pitch

or under a roof without a gutter, a gutter or diverter
should be fitted to prevent excessive water from pouring
down into the unit.

6.4.2 Professional Inspection

Inspections performed at least once a year by a
qualified technician are required to maintain your heat
pump’s safe and efficient operation. The following
basic safety checks must be performed.

1 Check for loose or broken wires and terminal

connections.

2. Verify the pressure switch operation. Turn the heat

pump OFF. Disconnect the power to the pump

time clock, or turn the pump time clock to an OFF

position. Turn the heat pump back ON. The heat

pump must not come on.

3. Inspect the electrical controls, specifi cally the

following:

a. High and Low limits

b. Pressure switch

c. Temperature control

4. Inspect the evaporator coil for blockage and clean

as necessary.

5. Check for spider webs or debris in the condensate

drain; clean if necessary.

6. Conduct a normal operating cycle and observe that

the unit operates properly.

Section 7. Professional Maintenance
and Service

7.1 Heat Pump Design

The Jandy Air Energy Heat Pump is one of the
most efficient ways to heat a pool or spa. The heat pump
transfers heat from the outside air to the pool or spa
water by means of an internal heat exchanger.

When the fan is turned on, warm air is drawn
through the refrigerant charged evaporator, turning
the cold liquid refrigerant to a warm gas. The gas then
flows through the compressor where it is compressed
resulting in a much higher temperature.

The hot gas enters the heat exchanger where the
water extracts the heat. The pump pulls in cool pool
water, which in turn converts the hot gas back into a
liquid refrigerant and starts the cycle over again.

NOTE The maximum heat output and effi ciency of a

heat pump is dependent upon the quality and
performance of the major components used.
As equally important are the environmental
conditions (for example, air temperature,
humidity, water temperature, and wind).

Page 25

Figure 18. Heat Pump Operation Overview

7.2 Heat Pump Components and Their

Operation

Evaporator Heat is collected in the evaporator

similar to a solar collector, which is a basic design

for collecting heat. The larger the surface area of

the evaporator, the more heat it can collect.

Fan The Heat Pump fan produces high volume airfl ow.

Adequate airfl ow is required to transfer warm air

to the large evaporator.

Compressor The compressor compresses the

refrigerant gas to a higher pressure, thus increasing

the temperature.

Heat Exchanger As the fi nal step to the heating

process, the heat exchanger transfers the heat

from the hot gas to the water. (Also known as a

condenser.)

Reversing Valve (For Units with Optional

Chiller) The reversing valve reverses the fl ow of

the refrigerant, which results in transferring cold

gas to the water, thus lowering the temperature.

Page 26

Section 8. Troubleshooting

8.1 Troubleshooting Guide

SYMPTOM CORRECTIVE ACTION

Heat pump will not start, no control board display. Breaker or fuse may be tripped. Reset breaker or check

fuse. If heat pump still does not run, call for service.

Heat pump will not start, control board display working. Heat pump may be in delay count down of 5 minutes

Make sure control board thermostat is calling for heater
to come on (check setting on thermostat and temperature
reading.) Make sure heat pump is not in cooling mode.

Heat pump runs but does not heat. Verify cold air is blowing out the top of the heat pump. If

the heat pump has just been installed or if the pool water
has been allowed to cool significantly, it is necessary to
run the heat pump continually for 24-48 hours. If the heat
pump has been in operation for some time, increase the
circulating pump time, or switch the control board to auto
heat function. If heating a spa, verify no air intake stand
pipes are open. If heat pump still does not heat call for
service.

Heat pump does not run and control board displays
LOW H2O FLOW.

Heat pump does not run and control board display
shows HIGH REFRIGERANT PRESSURE.

Heat pump does not run or short cycles and control
board display shows LOW REFRIGERANT PRESSURE.

Heat pump leaking water. Possible heat exchanger or plumbing leak. Turn the

Verify circulating pump is on and all necessary valves
are in the correct positions. Verify filter and skimmers
are clean. Check water level in pool. Temporarily turn off
all fountains and water falls that bypass the heat pump
water inlet. If this does not correct the problem, call for
service.

Verify circulating pump is on and that there are no
water flow restrictions to the heat pump. Make sure all
necessary valves are open or in the proper positions to
allow proper water flow to the heat pump. Verify filter and
skimmers are clean. Check for water level in the pool.
This condition may also appear if the heat pump has
not been operated for an extended period. To clear the
condition, cycle the heat pump, on and off, up to 3 times.
If this does not correct the problem call, for service.

Check that fan is operating and air is coming out of the
top of the heat pump, while short cycling. If heat pump
does not run at all, call for service.

heat pump off, then turn circulating pump on for at least
one hour to see if the water leak stops. If the water leak
stops, normal condensation is occurring. If the water leak
continues, after the heat pump is shut off for at least one
hour, call for service.

Page 27

8.2 Diagnostics

In the event a pressure switch opens or another
fault condition occurs, the LCD screen will display

the fault until the problem has been resolved. Please
refer to the following table for the list of diagnostic
conditions.

Diagnostic Condition Description

LOW H2O FLOW Low or restricted water flow through the heat pump.

The external bypass valve is in the wrong position, or the water
flow switch has malfunctioned. The water flow switch opens creating
a fault and the heat pump shuts off.

The LCD screen will display LOW H2O FLOW on the top line until
the switch closes. The ON LED will flash once every 2 seconds.

LOW COIL TEMPERATURE When the evaporator coil temperature is below 30°F, the heat pump

cannot operate effectively.

The coil thermistor reads the temperature and the control goes into
defrost if the defrost mode is not set to OFF in setup mode.

The LCD display will display LOW COIL TEMP on the top line for
the duration of the low coil temperature condition when the defrost
mode is set to OFF. When set to either Air Defrost or Reversing
Valve Defrost, the LCD display will show * Defrost Mode * for the
duration of the low coil temperature condition.

LOW REFRIGERANT PRESSURE When the ambient temperature is low, the suction pressure can

drop significantly.

This fault will cause the low pressure switch to open and the control
will shut off the compressor.

The LCD display will display LOW REFRIGERANT on the top line
and PRESSURE on the bottom line for the duration of the fault
condition. The ON LED will flash twice every 2 seconds.

HIGH REFRIGERANT PRESSURE When the head pressure builds too high, the high pressure switch

will open causing the heat pump to shut off immediately.

The control will sense this fault condition and shut off the
compressor until the switch re-closes.

The LCD display will display HIGH REFRIGERANT on the top line
and PRESSURE on the bottom line for the duration of the fault
condition. The ON LED will flash 3 times every 2 seconds.

HIGH WATER TEMPERATURE When the POOL or SPA water temperature heats to the maximum

allowed temperature or above, there could be safety risks for
anyone in the water.

The water thermostat will read this temperature and the control will
shut off the heat pump unless it is in CHILLER mode.

The LCD display will display HIGH H20 on the top line and
TEMPERATURE on the bottom line for the duration of the fault
condition. This feature also remains active when the control calls
for heat through a remote thermostat. This is to insure that water
temperature does not go to an abnormally high level due to a
possible malfunction of the remote sensor.

Page 28

Diagnostic Condition Description

LOW WATER TEMPERATURE When the POOL or SPA temperature chills to 50°F or below there

could be safety risks for anyone in the water.

The water sensor will read this temperature and the control will shut
off the chiller.

The LCD display will show LOW H2O on the top line and
TEMPERATURE on the bottom line for the duration of the fault
condition. This feature also remains active when the control calls
for chill through a remote thermostat. This is to insure that water
temperature does not go to an abnormally low level due to a
possible malfunction of the remote sensor.

COIL SENSOR PROBLEM In the event that the coil temperature sensor malfunctions or is not

connected the control will shut off the heat pump.

The LCD display will show COIL SENSOR on the top line and
MALFUNCTION on the bottom line until the problem is resolved.

WATER SENSOR PROBLEM In the event that the water temperature sensor malfunctions or is

not connected the control will shut off the heat pump.

The LCD display will show WATER SENSOR on the top line and
MALFUNCTION on the bottom line until the problem is resolved.

Section 9. Replacement Parts

9.1 Ordering Information

To order or purchase parts for the AE-Ti models
of heat pumps, contact your nearest Jandy dealer or
distributor. See the Jandy web site at www.jandy.com

9.2 Jandy AE-Ti Heat Pumps Parts List

Page 29

for the nearest service center. If they cannot supply you
with what you need, contact Jandy Customer Service
Department at P.O. Box 6000, Petaluma, California,
94954, Telephone [phone] extension 245.

Key
No. Description

1 Top Enclosure, Jacket All R3000200
2 Front Panel, Jacket 2000 R3000401
2 Front Panel, Jacket 2500,3000 R3000403
3 Service Access Panel All R3000500
4 Control Cover - Smoked All R3000600
5 Fan Motor, 208 VAC & 230 VAC All R3000701
5 Fan Motor, 380 VAC & 460 VAC All R3000702
6 Contactor, 1-Phase All R3000801
6 Contactor, 3-Phase All R3000802
7 Transformer, 1-Phase All R3000901
7 Transformer, 3-Phase All R3000902
8 Water Pressure Switch All R3001000
9 Capacitor, Fan Motor All R3001100
10 Capacitor, Compressor (55/440) Bristol 2000 R3001201
10 Capacitor, Compressor (60/370) Bristol 2500 R3001202
10 Capacitor, Compressor (80/370) Bristol 3000 R3001203
11 Controller Assembly All R3001300
12 Refrigerant HP Switch All R3001400
13 Refrigerant LP Switch All R3001500
14 Wire Harness Kit, 1-Phase (Not Shown) All R3001600
15 Fan Blade Set All R3001700
16 Fan Guard All R3001800
17 Plumbing Bypass Assembly All R3001900
18 2” PVC Union Set All R3002000
19 Evaporator Coil/Guard 2000 R3002101
19 Evaporator Coil/Guard 2500 R3002102
19 Evaporator Coil/Guard 3000 R3002103
20 Heat Exchanger Drain Kit All R3002200
21 Heat Exchanger Replacement Kit All R3002300
22 Compressor (55/440), 1-Phase 2000 R3002500
22 Compressor (60/370), 1-Phase 2500 R3002600
22 Compressor (80/370), 1-Phase 3000 R3002700
22 Compressor, 3-Phase 2000 R3003400
22 Compressor, 3-Phase 2500 R3003500
22 Compressor, 3-Phase 3000 R3003600
23 Thermal Expansion Valve

(Heating only, Not Shown)

23 Thermal Expansion Valve

(Reversing opt., Not Shown)
24 Water Temperature Sensor All R3002900
25 3-Phase Monitor All R3003000
26 Air Temperature Sensor All R3003100
27 Reversing Valve (Optional, Not Shown) 2500, 3000 R3003800
28 Achor Bracket Set (Not Shown) All R3003203
29 Heat Pump Drain Kit All R3004100

Model
No.

All R3002801

2500, 3000 R3002802

Order
Part No.

Page 30

9.3 Jandy AE-Ti Heat Pumps Exploded View

16

24, 26

This 10K thermistor is used as
a water temperature sensor when
installed in the water inlet pipe and
as an air temperature sensor when
installed in the evaporator coil.

Please note that the water temperature sensor
wiring is blue and the air temperature sensor
wiring is red.

12

RED WIRE

BLUE W

IRE

These pressure switches are installed in the
refrigerant line near the compressor.

YELLO

ORANGE WIRE

WWIRE

13

4

1

11

15

5

21

19

22

25

6

7

10

2

17

18

20

9

8

3

Notes

Page 31

Page 32

Notes

Page 33

LIMITED WARRANTY

Thank you for purchasing Jandy® pool and spa products. Waterpik Technologies (manufacturer of Jandy

®

products, including Laars

pool and spa heaters, Air Energy Heat Pumps, and Clormatic Electronic Chlorine
Generators) warrants all parts to be free from manufacturing defects in materials and workmanship for a period of
one year from the date of retail purchase, with the following exceptions:

AquaLink

•

NeverLube® valves are warranted for the life of pool and/or spa on which they were originally installed.

•

AquaPureTM Electronic Chlorine Generator Electrolytic Cells carry a 5 year limited warranty on a prorated basis.

•

Heat pump titanium coils carry a limited lifetime warranty.

•

®

RS units installed with Jandy Surge Protection Kits will be covered for two years.

This warranty is limited to the first retail purchaser, is not transferable, and does not apply to products that have
been moved from their original installation sites. The liability of Waterpik Technologies shall not exceed the repair
or replacement of defective parts and does not include any costs for labor to remove and reinstall the defective
part, transportation to or from the factory, and any other materials required to make the repair. This warranty does
not cover failures or malfunctions resulting from the following:

1. Failure to properly install, operate or maintain the product(s) in accordance with our published Installation,

Operation and Maintenance Manuals provided with the product(s).

2. The workmanship of any installer of the product(s).

3. Not maintaining a proper chemical balance in your pool and/or spa [pH level between 7.2 and 7.8, Total

Alkalinity (TA) between 80 to 120 ppm, Total Dissolved Solids (TDS) less than 2000].

4. Abuse, alteration, accident, fire, flood, lightning, rodents, insects, negligence or acts of God.

5. Scaling, freezing, or other conditions causing inadequate water circulation.

6. Operating the product(s) at water flow rates outside the published minimum and maximum specifications.

7. Use of non-factory authorized parts or accessories in conjunction with the product(s).

8. Chemical contamination of combustion air or improper use of sanitizing chemicals, such as introducing

sanitizing chemicals upstream of the heater and cleaner hose or through the skimmer.

9. Overheating; incorrect wire runs; improper electrical supply; collateral damage caused by failure of O-Rings,

DE grids, or cartridge elements; or damage caused by running the pump with insufficient quantities of water.

LIMITATION OF LIABILITY:

This is the only warranty given by Waterpik Technologies. No one is authorized to make any other warranties on
Waterpik Technologies' behalf. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND MERCHANTABILITY. WATERPIK TECHNOLOGIES EXPRESSLY DISCLAIMS
AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, INDIRECT OR PUNITIVE
DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY. This warranty gives you specific

legal rights. You may also have other rights which vary by state or province.

WARRANTY CLAIMS:

For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase,
model number, serial number and date of installation. The installer will contact the factory for instructions
regarding the claim and to determine the location of the nearest designated service center. If the dealer is not
available, you can locate a service center in your area by visiting www.jandy.com or by calling our technical
support department at [phone] extension 260 [for heap pumps call [phone]]. All returned parts
must have a Returned Material Authorization number to be evaluated under the terms of this warranty.

ETL LISTED

CONFORMS TO

UL STD 1995

CERTIFIED TO

H0569300A

CAN/CSA C22.2 NO.236

6000 Condor Drive • Moorpark, CA USA 93021

2735 NW 63rd CT• Fort Lauderdale, FL USA 33309

A Waterpik Technologies Company

• 707.776.8200 • Fax [phone]

• 954.970.4800 • Fax [phone]

Litho in U.S.A. © Waterpik Technologies 0501