Jammin Pro StudioMix 10 User Manual
USER'S MANUAL
IMPORTANT SAFETY SYMBOLS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The symbol is used to indicate that some hazardous live terminals are
involved within this apparatus, even under the normal operating conditions,
which may be sufficient to constitute the risk of electric shock or
The symbol is used in the service documentation to indicate that specific
component shall be replaced only by the component specified in that
documentation for safety reasons.
death.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
ON: Denotes the apparatus is turned on
OFF: Denotes the apparatus is turned off.
WARNING: Describes precautions that should be observed to prevent the danger
of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of
the apparatus.
NOTE:
IMPORTANT SAFETY INSTRUCTIONS
·Read these instructions.
·Keep these instructions.
·Heed all warning.
·Follow all instructions.
Water & Moisture·
The apparatus should be protected from moisture and
rain, can not used near water, for example: near bathtub, kitchen sink or a swimming pool, etc.
·Heat
The apparatus should be located away from the heat source such as radiators,
stoves or other appliances that produce heat.
20
Power supply
Power consumption
StudioMix 10: 18 W
StudioMix 12: 23 W
·Ventilation
Do not block areas of ventilation opening. Failure to do could result in fire. Always
install accordance with the manufacturer's instructions.
·Object and Liquid Entry
Objects do not fall into and liquids are not spilled into the inside of the apparatus
for safety.
Mains voltage
USA/Canada
U.K./Australia
Europe
Japan
Dimenstions
STUDIOMIX 10
Dimensions (H x W x D)
weight (net)
STUDIOMIX 12
Dimensions (H x W x D)
weight (net)
120 V~, 60 Hz, MXUL5 adapter
240 V~, 50 Hz, MXUK5 adapter
230 V~, 50 Hz, MXEU5 adapter
240 V~, 60 Hz, MXJP5 adapter
47mm / 37.5mm x 240mm x 208mm
approx. kg1.3
47mm / 37.5mm x 240mm x260mm
approx. 1.7 kg
·Power Cord and Plug
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit into your outlet,
refer to electrician for replacement.
·Power Supply
The apparatus should be connected to the power supply only of the type as marked
on the apparatus or described in the manual. Failure to do could result in damage
to the product and possibly the user.
Unplug this apparatus during lightning storms or when unused for long periods
of time.
·Fuse
To prevent the risk of fire and damaging the unit, please use only of the
recommended fuse type as described in the manual. Before replacing the fuse,
make sure the unit turned off and disconnected from the AC outlet.
·Electrical Connection
Improper electrical wiring may invalidate the product warranty.
·Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzol or alcohol.
Measuring conditions:
1:1kHz rel.to 0 dBu; 20 Hz - 20 kHz, line input; main output; unity gain.
Specifications and appearance may differ from those listed or illustrated.
19
·Servicing
Do not implement any servicing other than those means described in the manual.
Refer all servicing to qualified service personnel only.
·Only use accessories/attachments or parts recommended by the manufacturer.
·Warning
Please remember the high sound pressure do not only temporarily damage your
sense of hearing, but can also cause permanent damage. Be careful to select a
suitable volume.
TABLE OF CONTENTS
1.INTRODUCTION...................................................2
1.1 General mixing console functions.................................................................2
1.2 The user’ s manual..............................................................................3
1.3 Before you get started..........................................................................3
2.CONTROL ELEMENTS AND CONNECTORS .....................4
2.1 Mono channels..............................................................................4
2.2 Stereo channels.............................................................................6
2.3 Connector carry of the main section............................................................7
2.4 ................................................................................9Main section
2.5 ...................................................................11Digital effects processor
EQ mono channels
Low
Mid
High
EQ stereo channels
Low
Mid
High
Aux sends
Type
Impedance
Max.output level
Stereo aux return
Type
Impedance
Max.input level
80 Hz / 15 dB
2.5 kHz / 15 dB
12 kHz / 15 dB
80 Hz / 15 dB
2.5 kHz / 15 dB
12 kHz / 15 dB
1/4＂T S connector, unbalanced
approx. 20 k Ω
+22 dBu
1/4＂ TRS connector,
electronically balanced
approx. 20 k bal. /10 k unbal. Ω Ω
+22 dBu
2.6 ........................................................................12Rear Panel Section
3.APPLICATION..................................................13
3.1 .................................................................13Digital effects processor
3.2 ......................................................................14Rear Panel Section
4.INSTALLTION...................................................15
4.1 Mains connection............................................................................15
4.2 Audio connections...........................................................................15
5.SPECIFICATIONS................................................17
1
Main outputs
Type
Impedance
Max.output level
Control room outputs
Type
Impedance
Max.output level
Headphones output
Type
Max.output level
Main mix system data
Noise
Main mix @ -∞,
Channel fader -∞
Main mix @ 0 dB,
Channel fader -∞
Main mix @ 0 dB,
Channel fader @ 0 dB
XLR electronically balanced
approx. 240 bal./ 120 unbal. Ω Ω
+28 dBu
1/4＂TS connector, unbal.
approx. 120 Ω
+22 dBu
1/4＂TRS connector, unbalanced
+19 dBu / 150 (+25 dBu)Ω
2
-106 dB / -109 dB A-weighted
-95 dB / -98 dB A-weighted
-84 dB / -87 dB A-weighted
18
Loading...