Page 1
Performance/Capacities
Conveyors
AJ-64 Vision Series
•287 racks per hour hi-temp sanitizing
rinse
• 0.77 gallons per rack hi-temp sanitizing
rinse
• Incoming water pressure regulator
• Exclusive Adjust-A-Peak feature
(patented) allows the owner operator
to manually adjust the speed of the
conveyor system from 144 racks per
hour all the way to maximum capacity
of 287 racks per hour.
• Standard 25” clearance allows
owner operators the ability to wash
large utensils, trays, and bun pans.
• Totally electro-mechanical; no solid
state controls utilized.
• Fully automatic including auto-fill.
• Completely self-draining, stainless
steel wash and recirculating rinse
pumps.
• Exclusive “Energy Guard” controls
system energizes wash, recirculating
rinse, and final rinse sections only
when a rack is in place.
• Convenient, externally operated
lever drains.
• Stainless steel frame, legs, adjustable
bullet feet, and front appearance
panel are all standard.
• Standard 8” vent cowls/splash
shields on both wash and rinse ends
of the machine.
• Heavy gauge construction for extra
ruggedness and durability.
Standard Features
Operating Capacity
Racks per hour 287
Dishes per hour 7200
Glasses per hour 7200
Steam Coil Tank Heat
Steam Connection IPS (Inches) 3/4
Steam Flow Pressure (PSIG) 10-20
Consumption @ 15 PSIG (Lbs/hr) 100
Wash Pump Motor HP 2
Wash Pump Capacity (GPM) 270
Wash Tank KW 15
Conveyor Motor Horsepower 1/4
Conveyor Speed (Feet/minute) 8.0
Operating Temperatures
Wash Tank–°F (Minimum) 150
Power Rinse–°F (Minimum) 160
Rinse–°F (Minimum) 180
Dimensions (Inches)
Length between dishtables 64
Machine width 25
Wall Clearance (Minimum) 4.5
Cavity/dish clearance (Maximum) 25
Shipping Information
Weight (Lbs) 890
Dimensions (Inches)
Length 96
Depth 40
Height 78
Volume (Cubic feet) 174.0
Approximate Total Load AMPS
208V / 60HZ / 3PH 81.8
208V / 60HZ / 1PH 138.9
230V / 60HZ / 3PH 75.1
230V / 60HZ / 1PH 127.5
460V / 60HZ / 3PH 37.6
Booster Heater Options
External 40°F Min. Rise KW AMPS
208V / 60HZ / 3PH 34.5 95.8
230V / 60HZ / 3PH 36 90.5
460V / 60HZ / 3PH 36 45.2
External 70°F Min. Rise KW AMPS
208V / 60HZ / 3PH 45 125.0
230V / 60HZ / 3PH 45 108.0
460V / 60HZ / 3PH 45 54.0
Venting Requirements (CFM)
Input end 200
Output end 400
To tal CFM 600
Water Requirements
Incoming Wash Tank Temperature (°F) 180
With 36 KW booster heater option (°F) 140
With 45 KW booster heater option (°F) 110
Gallons per hour 222
Gallons per rack 0.77
Wash Tank Capacity (Gallons) 15.4
Incoming Waterline Size (IPS) (Minimum) 3/4
Flow Pressure (PSI) 15-25
Flow Rate Minimum (GPM) 3.7
Drainline Size IPS (Minimum) (Inches) 1 1/2
Power/Connections
Page 2
Conveyors
AJ-64 Vision Series
Specifications
NOTE:
The AJ-64 series conveyor dishmachines are
listed by the National Sanitation Foundation (NSF),
Underwriters Laboratories Inc. (UL), and by the Canadian
Standards Association (CSA). They also meet the requirements of A.S.S.E. Standard No. 1004.
PERFORMANCE:
Fully automatic, multiple tank,
rack conveyor dishwasher designed to wash, rinse, and
sanitize tableware and utensils commonly associated
with the preparation and consumption of food items in a
commercial foodservice operation. Sanitization is accomplished through hi-temp sanitization utilizing 180-195°F
fresh water rinse. The unit conveys standard 20” x 20”
dishracks through a recirculating detergent laden wash
section where 270 gallons per minute (GPM) of 150°F
wash water is pumped over the dishrack to remove the
food soil. It then enters the power rinse section where an
initial rinse of 160°F water at 270 (GPM) is pumped over
the dishrack. The rack is conveyor driven into a final
rinse section where a fresh water final rinse spray system removes remaining residual detergent and sanitizes.
The unit must be installed to a potable water line capable of supplying 222 gallons per hour between 180-195°F
at 15-25 PSI flow pressure for maximum hourly rack
capacity of 287 racks per hour.
CONSTRUCTION:
All stainless steel components
are 304 series stainless steel. No 400 series stainless
steel and/or plastics are utilized. Frame is constructed of
2” diameter stainless steel tubing formed and completely
saddle welded for superior strength. The wash and rinse
tank chambers are formed and heliarc welded 16 gauge
#2B finish. Hood is 16 gauge #3 finish. Stainless steel
feet are adjustable ±1/2”.
WAS H PUMP:
Internal wash pump located inside
the wash tub is totally stainless steel including the
impeller. The pump itself is totally integral with the motor
and self draining. Wash water is recirculated from the
wash tank through the manifolds and wash arm system
at the rate of 270 GPM.
WAS H PUMP MOTOR:
A 2 HP totally enclosed,
fan cooled type motor drives the wash pump and arms.
Single-phase motors are capacitor start, induction run
with internal thermal overload protection. Three-phase
motors are induction run with external overload protection. Motor shaft is supported by permanently lubricated
grease packed ball bearings.
POWER RINSE PUMP:
Internal power rinse
pump located inside the power rinse tub is totally stainless steel including the impeller. The pump itself is totally
integral with the motor and self draining. Rinse water is
recirculated from the tank through the manifolds and
rinse arm system at the rate of 270 GPM.
POWER RINSE PUMP MOTOR:
A 2 HP totally enclosed, fan cooled type motor drives the wash pump
and arms. Single-phase motors are capacitor start,
induction run with internal thermal overload protection.
Three-phase motors are induction run with external overload protection. Motor shaft is supported by permanently
lubricated grease packed ball bearings.
CONVEYOR SYSTEM:
Racks are conveyed
through the machine by a center-mounted, heavy-duty
stainless steel pawl bar with stainless steel cast, counterweighted, wide surface pawls. The pawl bar is designed
not to interfere with spray patterns in the wash, power
rinse, and final rinse sections. The pawl bar is driven by a
1/4 HP motor and worm drive gear reduction unit. The
conveyor motor itself is totally enclosed, non-ventilated.
Single-phase motors are capacitor start, induction run
with internal thermal overload protection. Three-phase
motors are induction run with external overload protection. Pawl bar conveyor drive unit is mounted on the left
hand side of the machine and is enclosed with a removable stainless steel cover. Maximum conveyor speed is 8.0
feet per minute.
ADJUST-A-PEAK:
The Adjust-A-Peak feature is a
mechanical feature located on the pawl bar drive unit itself
and allows the end-user to slow down the speed of the
conveyor drive unit when enhanced results are required
(i.e. baked-on food soil) or increase the speed of the conveyor drive unit when maximum capacity is required. By
slowing down the conveyor, a rack of tableware remains in
the prewash, wash, and rinse sections for longer periods of
time. When soil loads are heavy (i.e. pots and pans, trays,
and bun pans), adjusting the conveyor to slower speeds
means outstanding results.
CHAMBER:
The chamber has a standard clearance
of 25” which is the highest clearance in the industry--even higher than competitive higher hood options. This
adds to the versatility of the machine since you can easily
accommodate larger utensils such as sheet pans and 60
quart mixing bowls. The combination of a higher hood in
conjunction with manually slowing down the conveyor utilizing the Adjust-A-Peak feature produces superior results
as well as adding to the versatility of the machine.
CONTROLS:
Controls are located in a stainless steel
control box mounted on top of the machine for ease of
access and increased reliability. Power “ON/OFF” switch
is the only manual switch required. “Energy Guard” fully
automates the machine and utilizes switching logic to
operate wash, power rinse, and final rinse sections only
when a rack is being washed or rinsed. It will turn the
conveyor off when a rack exits the machine and there
are no other racks in the unit. Regardless of machine
voltage, all control circuitry will be operated from a 110
volt control circuit transformer. Again, the Adjust-A-Peak
feature eliminates the need for manual controls since you
have the ability to slow down the conveyor for extended
wash, power rinse, and final rinse contact time. The unit
is completely wired with 105°C, 600V thermoplastic insulated wire and routed through UL approved conduit. The
control circuit itself is protected by a manual reset 1
AMP overload protector located on the front of the control box.
FILL:
Initial fill of wash and power rinse tanks is automatic when machine is initially energized. The fill line
needs to be hooked up to a 180°F minimum potable
water line which normally would be supplied by an external booster heater or our optional Hatco booster heater
packages. Fill is controlled by a standard solenoid valve
and vacuum breaker assembly. The incoming water solenoids are activated by stainless steel float systems located in the wash tank and power rinse tank for maintaining
required fill levels.
RECIRCULATING WASH:
The wash tank has a
15.4 gallon capacity and maintains that level with a
skimming type overflow. Washing action is accomplished
by recirculating detergent laden water in the wash tank
through upper and lower wash arms. Make-up water
comes from the power rinse section and is controlled at
approximately 2 GPM. The wash arms are 18” long.
Wash performance commences 5” into the machine.
Wash section is automatically activated by racks as they
pass through. Wash arms, upper and lower, contain 43
separate stripping nozzles for superior performance. Both
wash arms are easily removable and along with removable wash arm end caps, are easily cleanable without the
use of tools. Large stainless steel strainer pans, as well
as a pump intake strainer for secondary protection are
readily accessible and removable for cleaning purposes.
Knockouts and connections are provided to allow easy
installation of detergent concentration sensor and dispenser tubing by others.
POWER RINSE:
The power rinse tank has a 15.4
gallon capacity and maintains that level with a skimming
type overflow. Rinsing action is accomplished by recirculating final rinse water in the tank through upper and
lower wash arms. Makeup water comes from the final
rinse section and is controlled at approximately 2 GPM.
The power rinse arms are 12” long. The power rinse section is automatically activated by racks as they pass
through. Power rinse arms, upper and lower, contain 32
separate stripping nozzles for superior performance. Both
power rinse arms are easily removable and along with
removable wash arm end caps, are easily cleanable
without the use of tools. Large stainless steel strainer
pans, as well as a pump intake strainer for secondary
protection are readily accessible and removable for
cleaning purposes.
Page 3
FINAL RINSE:
Fresh pressurized rinse water enters
the machine through a standard “Y” strainer, solenoid
valve, and approved vacuum breaker assembly and is
plumbed to upper and lower final rinse arms located at
the output end of the machine. A single row of fan jet
nozzles are located on both rinse arms. Connection point
is provided for rinse agent injection into the final rinse
line by others. Total final rinse flow rate is 3.7 GPM.
DRAIN, OVERFLOW, AND MAKE-UP:
The
machine is designed to maintain appropriate wash and
power rinse tank water levels at all times even at low
pressures. The overflow system is designed to automatically skim the surface of the wash and power rinse
tanks. Make-up water from the final rinse system replenishes the wash and power rinse water, maintains water
levels as well as appropriate tank temperatures. Large
levers located on the front panel of the machine operate
valves that drain the machine completely.
PRESSURE REDUCING VALVE:
Factory installed on incoming water line to control water
pressure.
Additional Standard
Equipment:
• Vent cowls/splash shields with 4” x 16” openings covered with
removable plates for connection to exhaust ducts when required.
• Flexible NSF approved strip curtains provided at the ends of
the vent cowls as well as at the ends of the machine and separating the wash, power rinse, and final rinse sections.
• Extra large inspection doors located on front of machine for
easy access and cleanability
• Safety door switches shut down machine should any door be
opened during operation.
• Stainless steel front appearance panel.
• Positive low level water protection for wash and power rinse
tank heat.
• Sealed dial type thermometers for the wash, power rinse and
final rinse temperatures.
Optional Mandatory
Equipment:
Wash Tank Heating Equipment
(Choose One):
ELECTRIC:
Low watt density 25 KW tubular heating
elements mounted inside the tanks (15 KW wash and 10
KW power rinse) and easily removable from the outside.
The heaters are protected by a stainless steel float system as well as high limit overload protection. Water temperature in the tanks is controlled and maintained by fast
reacting thermostats which control the heating elements.
STEAM:
Stainless steel coils are utilized rather than
injectors so that contaminated steam being injected into
the wash water is not an issue. Stainless steel tubular
steam coils are mounted inside the wash and power
rinse tanks below the optimum water level. The coils are
protected by a stainless steel float system. An external
steam “Y” strainer and high temperature steam solenoid
regulates the flow of steam through the coils.
Temperature in the tanks is controlled and maintained by
fast reacting thermostats which control the operation of
the steam solenoids. A float and thermostatic steam trap
is provided and removes steam condensate from the
steam coils which can either be plumbed to a drain or
pumped back to the boiler if a condensate return system
is available. Steam coils require a minimum of 10 PSIG
flowing steam supply and a maximum of 20 PSIG. Install
with a steam pressure regulator (by others) if steam
supply exceeds 20 PSIG.
Optional Features and
Accessories:
EXTERNAL ELECTRIC BOOSTER HEATER:
External 36 KW Hatco booster heater boosts incoming
140°F water to a minimum of 180°F for hi-temp sanitizing rinse. Custom features include castone-lined tank,
low water cutoff, pressure relief valve, as well as a pressure reducing valve. Unit is located next to the output
end of the machine, completely preplumbed. Power to
the booster heater requires a separate electrical connection. Unless specified otherwise, electrical characteristics
of the booster heater will be the same as that of the
dishwasher. The booster heater is approximately 36 KW
and is available in 208/240/480 voltages/3 phase only.
EXTERNAL 70°F RISE BOOSTER HEATER:
External 45 KW Hatco booster heater capable of boosting
incoming 110°F water a minimum of 70 degrees to a
minimum of 180°F for hi-temp sanitizing rinse. Unit is
located next to the output end of the machine and comes
completely preplumbed. Power to the booster heater
requires a separate electrical connection. Unless specified otherwise, electrical characteristics of the booster
heater will be the same as that of the dishwasher. The
booster heater is available in 208/240/480 voltages/3
phase only.
STEAM BOOSTER HEATER:
Sized to be connected to a standard 140°F incoming water supply in
order to insure 180-195°F hi-temp sanitizing final rinse
requirements. Unit comes complete with steam “Y”
strainer and high temperature steam solenoid as well as
a steam pressure relief valve. Water temperature is controlled and maintained by a fast reacting thermostat
which controls the operation of the steam solenoid. A
float and thermostatic steam trap is provided and
removes steam condensate from the coil which can
either be plumbed to a drain or pumped back to a boiler
if a condensate return system is available. Must be
installed with a steam pressure regulator (by others) if
steam supply exceeds 20 PSIG.
TA BLE LIMIT SWITCH:
Factory wired to machine
and mounted to the backsplash of the table in the field.
Prevents damage to conveyor drive system, racks, and
dishes due to racks backing up on the output end of the
machine. Highly recommended for clean dishtables less
than 10 feet in length.
VENT COWL COLLARS:
Factory installed 4” x
16” x 7” high collars located on the vent cowls to allow
easy connection to an external exhaust system including
a standard “pant-leg” type exhaust duct. Includes
adjustable and lockable damper flap for fine tuning
exhaust system to remove appropriate CFM requirements.
50 CYCLE (HERTZ) ELECTRICAL
CHARACTERISTICS:
Units are available in 50 HZ
in the following voltages: 208V/1 or 3PH, 230V/1 or 3PH,
380V/3PH, and 460V/3PH. Units operating at 50 HZ are
not submitted for UL Listing.
SIDELOADER:
Factory installed option on input end
of conveyor machine. This feature allows the machine to
be installed close to a corner and maximize dishroom
space. The sideloader option is available in both the
hooded and unhooded versions. See separate spec sheets
for details.
EXHAUST VENT FAN CONTROL:
Automatically turns exhaust vent fan on when rack enters
the machine. Delay timer also turns off the exhaust vent
fan 5-10 seconds after rack exits machine when no other
racks are being conveyed through the machine.
FLANGED FEET:
Available for installations where
permanent mounting to the floor is required. Fully
adjustable for required height.
WATER HAMMER ARRESTOR:
Installed
inside the supply line.
Page 4
Specifications
Conveyors
www.jacksonmsc.com
1-888-800-5672
AJ-64 Vision Series
Note: Check and/or copy all that apply.
AJ-64 Series Rack Conveyor Dishwasher— Item No. ____________
Shall be a Jackson AJ-64 Series, multiple tank rack conveyor dishwasher.
Sanitization shall be accomplished by using hi-temp (180°F minimum)
sanitizing rinse.
Electrical characteristics shall be:
______ 208V/60HZ/3PH ______ 208V/50HZ/3PH
______ 208V/60HZ/1PH ______ 208V/50HZ/1PH
______ 230V/60HZ/3PH ______ 230V/50HZ/3PH
______ 230V/60HZ/1PH ______ 230V/50HZ/1PH
______ 460V/60HZ/3PH
Wash tank heating shall be a minimum of 150°F for hi-temp applications
and accomplished by:
______ 10 KW (total 20 KW) electric heating element
thermostatically controlled.
______ Stainless steel steam coils thermostatically controlled.
Direction of rack flow shall be (when standing in front of machine):
______ Right-to-Left ______ Left-to-Right
______ External Hatco 36 KW booster heater for a minimum 40°F rise
and available in the following voltages:
______ 208V/50 or 60HZ/3PH
______ 240V/50 or 60HZ/3PH
______ 480V/50 or 60HZ/3PH
______ External Hatco 45 KW booster heater for a minimum 70°F rise
and available in the following voltages:
______ 208V/50 or 60HZ/3PH
______ 240V/50 or 60HZ/3PH
______ 480V/50 or 60HZ/3PH
______ Steam booster heater.
______ Table limit switch completely prewired and extending from the
output end of the machine, available in 9’0” length.
______ Table limit switch completely prewired and extending from the
output end of the machine, available in 12’0” length.
______ Table limit switch completely prewired and extending from the
output end of the machine, available in 15’0” length.
______ Installed 4" x 16" x 7" high vent cowl collars for easy connection
to an external exhaust system and including adjustable and lockable damper flaps.
______ output end only ______ input end only
______ both ends
______ Incoming water hammer arrestor completely installed.
______ Sideloader installed on input end of machine.
______ unhooded sideloader ______ hooded sideloader
______ Exhaust fan control controls external exhaust fan power and
duration time.
______ Flanged feet for permanent in-place mounting to the floor.
• Capacity of 288 racks per hour
utilizing 0.77 gallons of water per
rack for hi-temp sanitizing rinse.
• Incoming water pressure regulator.
• Adjust-A-Peak conveyor drive
system to manually adjust rack
capacity of the machine.
• Minimum 25" clearance
throughout machine.
• Exclusive “Energy Guard”
controls system energizes wash,
recirculating rinse, and final
rinse sections only when a rack
is in place.
• Completely electro-mechanical;
no solid-state controls.
• Fully automatic operation including auto-fill.
• Completely self draining, stainless steel wash and recirculating
rinse pumps.
• Convenient, externally operated
lever drains.
• Vent cowls/splash shields with
extra curtains on both wash and
rinse ends of the machine.
• Stainless steel frame, legs,
adjustable bullet feet, and front
appearance panel.
• All 304 series stainless steel
construction; no 400 series
stainless steel and no plastics
utilized.
Unit shall have the following features as optional extras:
Unit shall have the following features:
07610-002-66-78
All specifications subject to change without notice.
Page 5
Conveyors
AJ-64
Legend to Drawing
A– Electrical Connection - See Table for Amperage
Requirements (on back)
B–Water Inlet - 3/4” I.P.S., 180°F Water Required
C– Drain Connection-1 1/2” I.P.S.
D–Vent Collar/Splash Shield
E–Vent Collar with Damper 4”w. x 16”lg x 7”high-Optional
F– Steam Connection-1” I.P.S.
G– Condensate Return-1” I.P.S.
Notes:
– All vertical dimensions are +/- 1/2” from floor due to
adjustable bullet feet.
– Utility connections are identical for either direction
of operation.
Left to Right or Right to Left
Operation Shown
F
6 1/2"
11 1/4"
25"
21"
Opening
21 1/2"
1"
B
Rear of
Machine
69 5/8"
G
C
A
Rear of
Machine
67 1/2"
1 7/8"
12"
8"
84"
w/Doors
Open
B
E
7"
D
62 1/2"
29"
10"
Drive
Unit
C
80"
Overall
64"
Table to Table
35"
32 3/4"
25"
10"
10 3/8"
8"
5"
G
20"
D
F
E
A
75 1/2"
34"
Page 6
8"
4 1/2"
8"
4"72"
10 1/2"
21" Opening
80"
4"w. x 16"lg cutout in
Vent Cowl/Splash Shield.
Shipped with Cover Plate.
12 1/2"
25"
64"
Table to Table
ConveyorsAJ-64
www.jacksonmsc.com
1-888-800-5672
Approximate Total Load Amperes
Power Supply AJ-64CE AJ-64CS
208/60/1 138.9 18.8
230/60/1 127.5 18.8
208/60/3 81.8 12.3
230/60/3 75.1 12.3
460/60/3 37.6 6.2
Recommended Table Fabrication
07610-002-66-79
All specifications subject to change without notice.
Tub Will Accept
a Table Flange
Up to 24 7/8"
Table Turndown
Flange 3/4" Max
3/4"
21"
Note:
Rack Rail
Rack Rail Height
Above Dishtable
1/4" – 5/16"
Tu b
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Loading...