Page 1
Power/Connections
Approximate Total Load AMPS
208V / 60HZ / 3PH 48.4
208V / 60HZ / 1PH 82.3
230V / 60HZ / 3PH 44.4
230V / 60HZ / 1PH 75.5
460V / 60HZ / 3PH 22.2
Booster Heater Options
External 40°F Min. Rise KW AMPS
208V / 60HZ / 3PH 7 29.0
230V / 60HZ / 3PH 7 25.0
460V / 60HZ / 3PH 7 13.0
External 70°F Min. Rise KW AMPS
208V / 60HZ / 3 PH 12 33.0
230V / 60HZ / 3PH 12 29.0
460V / 60HZ / 3PH 12 14.5
Venting Requirements (CFM)
Input end
Output end 400
Total CFM 600
ater Requirements
W
Incoming Water Temperature (°F) 180
With 7 KW booster heater option (°F) 140
With 12 KW booster heater option (°F) 110
Gallons per hour:
Hi-temp sanitization 66
Gallons per rack:
Hi-temp sanitization 0.55
ank Capacity (Gallons)
ash T
W
Incoming Waterline Size (IPS) (Minimum) 1/2
I)
Flow Pressure (P
Flow Rate Minimum (GPM)
Hi-temp sanitization 3.9
Drainline Size IPS (Minimum) (Inches) 1 1/2
S
200
20.4
15-25
TSC-44 Traditional
Series
Standard Features
racks per hour hi-temp sanitizing
• 119
rinse.
• 0.55 gallons per rack hi-temp
sanitizing rinse.
• Incoming water pressure regulator
• Standard 18” clearance.
• Complete Right-to-Left and Left-toRight convertibility in the field.
• Totally electro-mechanical; no solid
state controls utilized.
• Fully automatic including auto-fill.
• Completely self-draining stainless
steel wash pump.
• Exclusive “Energy Guard” controls
system operates wash and rinse
sections only when a rack is being
washed or rinsed.
• A long 16” wash section as well as
18” separation between wash and
rinse produces superior results.
Performance/Capacities
Operating Capacity
Racks per hour
Hi-temp Sanitization 119
Dishes per hour
Hi-temp Sanitization 2975
Glasses per hour
Hi-temp S
Steam Coil Tank Heat
Steam Connection I
Steam Flow Pressure (PSIG) 10-20
Consumption @ 15 PSIG (Lbs/hr) 60
Wash Pump Motor HP 2
Wash Pump Capacity (GPM) 270
Wash Tank KW 15
Conveyor Motor Horsepower
Conveyor Speed (Feet/minute)
Hi-temp Sanitization 3.3
anitization
P
S (Inc
2975
hes)
• Convenient, externally operated
lever drain.
Stainless steel frame, legs, adjustable
•
bullet feet, and front appearance panel
are all standard.
• Standard 8” vent cowls/splash
shields on both wash and rinse ends
of the machine.
• Heavy gauge construction for extra
ruggedness and durability.
Operating Temperatures
Wash Tank–°F (Minimum)
Hi-temp Sanitization 160
Rinse–°F (Minimum)
Hi-temp Sanitization 180
hes)
hes)
3/4
1/4
Dimensions (Inc
Length between dishtables 44
Machine width 25
Wall Clearance (Minimum) 4.5
Cavity/dish clearance (Maximum) 18
Cavity width 20-1/2
Shipping Information
Weight (Lbs) 641
Dimensions (Inc
Length
Depth 40
Height 78
olume (Cubic feet)
V
13
Conveyors
76
8
Page 2
TSC-44 Traditional
Series
Specifications
NOTE:
The TSC-44 series conveyor dishmachines are
SF International Inc. (NSF) and Underwriters
N
Laboratories Inc. (UL) listed. They also meet the requirements of A.S.S.E. Standard No. 1004.
PERFORMANCE:
conveyor dishwasher designed to wash, rinse, and sani
tize tableware and utensils commonly associated with
the preparation and consumption of food items in a commercial foodser
plished either through hi-temp sanitization utilizing 180195°F fresh water rinse. The unit conveys standard 20” x
20” dishracks through a recirculating detergent laden
wash section where 270 gallons per minute (GPM) of
160°F wash water is pumped over the dishrack to
remove the food soil. The rack is then conveyor driven
into a final rinse section where a fresh water final rinse
spray system removes residual detergent and sanitizes.
For hi-temp sanitizing, the unit must be installed to a
potable water line capable of supplying 66 gallons per
hour between 180-195°F at 15-25 PSI flow pressure for
maximum hourly rack capacity of 119 racks per hour.
CONSTRUCTION:
are 304 series stainless steel. No 400 series stainless
steel and/or plastics are utilized. Frame is constructed of
2” diameter stainless steel tubing formed and completely
saddle welded for superior strength. The wash tank, and
rinse chamber are formed and heliarc welded 16 gauge
#2B finish. Hood is 16 gauge #3 finish. Stainless steel
feet are adjustable ±1/2”.
WASH PUMP:
wash tub is totally stainless steel as is the impeller. The
wash pump itself is totally integral with the motor. Wash
water is recirculated from the wash t
manifolds and wash arm system at the rate of 2
H PU
AS
W
fan cooled type motor drives the wash pump and arms.
Single-phase motors are capacitor st
with internal thermal overload protection. T
motors are induction run with external overload protection. Motor shaft is suppor
ked ball bearings.
grease pac
CONVEY
through the machine by a center-mounted, heavy-duty
ainless steel pawl bar with stainless steel cast, counter-
st
weighted, wide sur
to not interfere with spray patterns in the wash, and
rinse section. The pawl bar is driven by a 1/4 HP motor
and worm drive gear reduction unit. T
itself is totally enclosed, non-ventilated. Single-phase
OR S
Fully automatic, single tank, rack
vice operation. Sanitization is accom-
All stainless steel components
Internal wash pump located inside the
ank through the
0 G
7
TOR:
O
P M
M
face pawls. T
A 2 H
ted by permanently lubricated
M:
STE
Y
ally enclosed,
P tot
t, induction run
ar
hree-phase
s are conveyed
k
ac
R
he pawl bar is designed
he conveyor motor
M.
P
motors are capacitor st
thermal overload protection. Three-phase motors are
induction run with external overload protection. Pawl bar
conveyor drive unit is mounted on the left hand side of
the machine and is enclosed with a removable stainless
steel cover. Maximum conveyor speed is 3.3 feet per
minute for hi-temp mac
-
BER:The chamber has a standard clearance
CHAM
of 18”.
CONTROLS:
control box mounted on top of the machine for ease of
access and increased reliability. Power “ON/OFF” switch
is the only manual switch required. “Energy Guard” fully
automates the machine and utilizes switching logic to
operate wash and rinse sections only when a rack is
being washed or rinsed as well as turning the conveyor
off when a rack exits the machine and there are no other
racks in the machine. Regardless of machine voltage, all
control circuitry will be operated from a 110 volt control
circuit transformer. The unit is completely wired with
105°C, 600V thermoplastic insulated wire and routed
through UL approved conduit.
FILL:
Initial fill of wash tank is automatic when
machine is initially energized. The wash tank fill line
needs to be hooked up to a 180°F minimum potable
water line which normally would be supplied by an external booster heater or our optional Hatco booster heater
packages. Fill is controlled by a standard solenoid valve
and vacuum breaker assembly. The incoming water solenoid is activated by a stainless steel float system located
in the wash tank for required maintenance of the wash
tank water level.
RECIRCULATING WASH:
has a 20.4 gallon capacity and maintains that level with
a skimming t
plished by recirculating detergent laden water in the
wash tank through upper and lower wash arms. Make-up
water comes from the final rinse section and is controlled at approximately 2 GPM. The arms themselves are
extended and create a longer wash section than competitive models. Wash section is automatically activated by
racks as they pass through. Wash arms, upper and lower,
contain 36 separate stripping nozzles for superior performance. All wash arms are easily removable and along
with removable wash arm end caps, are easily cleanable
without the use of tools. Large stainless steel strainer
pans, as well as a pump intake strainer for secondary
protection are readily accessible and removable for
cleaning purposes. Knockouts and connections are provided to allow easy installation of detergent concentration sensor and dispenser tubing by others.
art, induction run with internal
hines.
Controls are located in a stainless steel
The wash tank itself
ype overflow. Washing action is accom-
Conveyors
NAL RINSE:Fresh pressurized rinse water enters
FI
the machine through a standard “Y” strainer, solenoid
valve, and approved vacuum breaker assembly and is
plumbed to upper and lower final rinse arms located at
the output end of the machine. Single rows of fan jet
nozzles are located on both rinse arms. Connection points
are provided for both rinse agent injection into the final
rinse line by others. Total final rinse flow rate is 3.9 GPM.
DRAIN, OVERFLOW, AND MAKE-UP:
machine is designed to maintain appropriate wash tank
water levels at all times even at low pressures. The overflow system is designed to automatically skim the surface of the wash tank. Make-up water from the final
rinse system not only replenishes the wash water but
also helps maintain appropriate water levels as well as
appropriate wash tank temperatures. A large lever located on the front panel of the machine operates a drain
valve and drains the machine completely.
PRESSURE REDUCING VALVE:
installed on incoming water line to control water pressure.
The
Factory
Page 3
Additional Standard
Equipment:
• Vent cowls/splash shields with 4” x 16” openings covered
with removable plates for connection to exhaust ducts
when required.
• Flexible strip curtains provided at the ends of the
vent cowls as well as at the ends of the machine and
separating the prewash, wash, power rinse, and final
rinse sections.
• Extra large inspection doors located on front of
machine for easy access and cleanability.
• Safety door switches shut down machine should any
door be opened during operation.
• Direction of machine operation easily convertible in the
field if required.
• Stainless steel front appearance panel.
• Positive low level water protection for wash and power
rinse tank heat.
• Sealed dial type thermometers for the wash and final
rinse temperatures.
Optional Mandatory
Specifications:
WASH TANK HEATING EQUIPMENT
(Choose One):
ELECTRIC:
elements mounted inside the wash tank and easily
removable from the outside. The heaters are protected
by a stainless steel float system as well as high limit
overload protection. Water temperature in the tanks is
controlled and maint
h control the heating elements.
whic
STEAM:
injectors so that contaminated steam being injected into
the wash water is not an issue. St
steam coils are mounted inside the wash and power
rinse tanks below the optimum water level. The coils are
protected by a st
steam “Y” strainer and high temperature steam solenoid
regulates the flow of steam through the coils.
emperature in the tanks is controlled and maintained by
T
fast reacting thermost
the steam solenoids. A float and thermostatic steam trap
is provided and removes steam condensate from the
steam coils whic
pumped back to the boiler if a condensate return system
is available. Steam coils require a minimum of 1
flowing steam supply and a ma
with a steam pressure regulator (by others) if steam
Low watt density 15 KW tubular heating
ained by fast reacting thermost
ainless steel coils are utilized rather than
St
ainless steel tubular
ainless steel float system. An external
h control the operation of
ats whic
h can either be plumbed to a drain or
0 PSIG
G. Install
I
ximum of 20 P
S
ats
supply exceeds 20 PSIG.
Optional Features and
ccessories:
A
EXTERNAL 40°F ELECTRIC BOOSTER
HEATER:
ing 14
itizing rinse. Custom features include castone-lined tank,
low water cutoff, pressure relief valve, as well as a pressure reducing valve. Unit is located next to the output
end of the machine, completely preplumbed. Power to
the booster heater requires a separate electrical connection. Unless specified otherwise, electrical characteristics
of the booster heater will be the same as that of the
dishwasher. The booster heater is available in
208/240/480 voltages/3 phase only.
EXTERNAL 70°F RISE BOOSTER HEATER:
External 12 KW booster heater capable of boosting
incoming 110°F water a minimum of 70 degrees to a minimum of 180°F for hi-temp sanitizing rinse. Unit is located
next to the output end of the machine and comes completely preplumbed. Power to the booster heater requires
a separate electrical connection. Unless specified otherwise, electrical characteristics of the booster heater will
be the same as that of the dishwasher. The booster
heater is available in 208/240/480 voltages/3 phase only.
STEAM BOOSTER HEATER:
nected to a standard 140°F incoming water supply in
order to insure 180-195°F hi-temp sanitizing final rinse
requirements. Unit comes complete with steam “Y”
strainer and high temperature steam solenoid as well as a
steam pressure relief valve. Water temperature is controlled and maintained by a fast reacting thermostat
whic
and thermostatic steam trap is provided and removes
steam condensate from the coil which can either be
plumbed to a drain or pumped back to a boiler if a condensate return system is available. Must be installed with
a steam pressure regulator (by others) if steam supply
exceeds 20 PSIG.
TABLE LIMIT SWITCH:
and mounted to the backsplash of the table in the field.
Prevents damage to conveyor drive system, racks, and
dishes due to racks backing up on the output end of the
machine. Highly recommended for clean dishtables less
than 10 feet in length.
VENT COWL COLLARS:
x 7” high collars located on the vent cowls to allow easy
connection to an external exhaust system including a standard “pant-leg” type exhaust duct. Includes adjustable and
lockable damper flap for fine tuning exhaust system to
remove appropriate CFM requirements.
External 7 KW booster heater boosts incom-
0°F water to a minimum of 180°F for hi-temp san-
Sized to be con-
h controls the operation of the steam solenoid. A float
Factory wired to machine
Factory installed 4” x 16”
50 CYCLE (HERTZ) ELECTRICAL
CTERISTICS:
CHARA
in the following voltages: 208V/1 or 3PH, 230V/1 or 3PH,
380V/3PH, and 460V/3PH. Units operating at 50 HZ are
not submitted for U
IDELOADER:Factory installed option on input end
S
of conveyor machine. This feature allows the machine to
be installed close to a corner and maximize dishroom
he sideloader option is available in both the
space. T
hooded and unhooded versions. See separate spec sheets
for details.
EXHAUST VENT FAN CONTROL:
Automatically turns exhaust vent fan on when rack
enters the machine. Delay timer also turns off the
exhaust vent fan 5-10 seconds after rack exits machine
when no other racks are being conveyed through the
machine.
FLANGED FEET:
permanent mounting to the floor is required. Fully
adjustable for required height.
WATER HAMMER ARRESTOR:
inside the supply line.
Units are available in 5
L Listing.
Available for installations where
0 HZ
Installed
Page 4
TSC-44 Traditional
Series
cifications
Spe
Note: Chec
TSC-44 Series Rack Conveyor Dishwasher—Item No. ____________
Shall be a Jackson TSC-44 series, single tank rack conveyor dishwasher.
Sanitization shall be accomplished by using:
______ Hi-temp (180°F minimum) sanitizing rinse
Electrical characteristics shall be:
______ 208V/60HZ/3PH ______ 208V/50HZ/3PH
______ 208V/60HZ/1PH ______ 208V/50HZ/1PH
______ 230V/60HZ/3PH ______ 230V/50HZ/3PH
______ 230V/60HZ/1PH ______ 230V/50HZ/1PH
______ 460V/60HZ/3PH
Wash tank heating shall be a minimum of 160°F for hi-temp applications
and accomplished by:
______ 15 KW electric heating elements thermostatically controlled.
______ Stainless steel steam coils thermostatically controlled.
Direction of rack flow shall be (when standing in front of machine):
______ Right-to-Left ______ Left-to-Right
k and/or copy all that apply.
Conveyors
Unit shall have the following features:
119 racks per hour utilizing 0.55
•
gallons of water per rack for
hi-temp sanitizing rinse.
• Incoming water pressure regulator.
• Standard 18" clearance
throughout machine.
• Exclusive “Energy Guard” controls system energizes prewash,
wash, recirculating rinse, and
final rinse sections only when a
rack is in place.
• Right-to-Left and Left-to-Right
convertibility in the field.
• Completely electro-mechanical;
no solid-state controls.
• Fully automatic operation including auto-fill.
• Stainless steel wash pump
and impeller and completely
self-draining.
Wash section must be a mini-
•
mum of 16” in length as well as
18” separation between recirculating wash and final rinse.
• Convenient, externally operated
lever drain.
• Vent cowls/splash shields with
extra curtains on both wash and
rinse ends of the machine.
• Stainless steel frame, legs,
adjustable bullet feet, and front
appearance panel.
• All 304 series stainless steel
construction; no 400 series
stainless steel and no plastics
utilized.
Unit shall have the following features as optional extras:
______ External electric 7 KW booster heater for a minimum 40°F rise
and available in the following voltages:
0HZ/3PH
0 or 6
______ 20
______ 240V/50 or 60HZ/3PH
______ 4
______ External electric 12 KW booster heater for a minimum 70°F rise
and available in the following volt
______ 208V/50 or 60HZ/3PH
______ 240V/50 or 60HZ/3PH
______ 4
______ Steam booster heater.
______ Exhaust fan control controls external exhaust fan power and
duration time.
______ Flanged feet for permanent in-place mounting to the floor.
8V/5
0 or 6
0V/5
8
80V/50 or 60HZ/3PH
.jacksonmsc.com
www
1-888-800-5672
0H
/3PH
Z
ages:
______ Table limit switch completely prewired and extending from the
output end of the machine, 15’0” long.
______ Whisker-style switch
______ Striker plate switch
______ Photosensor switc
______ Inst
______ Incoming water hammer arrestor inst
______ Sideloader installed on input end of machine.
alled 4" x 16" x 7" high vent cowl collars for easy connection
to an external exhaust system and including adjustable and lockable damper flaps.
______ output end only ______ input end only
______ both ends
______ unhooded sideloader ______ hooded sideloader
h
alled.
6 A 8/0
6-9
610-002-9
7
All specifications subject to change without notice.
0
4
Page 5
8"
62"
8"
60"
4"
6"
2-1/4"
10"
10"
7"
Left to Right or Right to Left
66"
HEIGHT WITH DOOR OPEN: 72"
E
3"
Operation Shown
Legend to Drawing
A– Machine water inlet 1/2” I.P.S., 59 1/2” above finished
.
floor
B– Electrical connection-see table for amperage
requirements.
C– Drain connection-1 1/2” I.P.S.
D– Incoming low pressure steam connection, 3/4” FPT
(gate valve supplied) (steam heat models only). NOTE:
steam connection shown is for right to left model; connec
tion is mounted on opposite end with the s
ame dimen-
sions for left to right.
E– Condensate return connection, 3/4” FPT (return to
boiler feeder or open drain) (steam heat models only).
steam connection shown is for right to left model; connection is mounted on opposite end with the same dimensions for left to right.
-
TSC-44 Drawing
Height with door open is 72”.
66”
Approximate Total Load Amps
TS Series
Electrical Electric Heat* Steam Heat*
Data TSC-44 TSC-44S
1 PH 3 PH 3 PH1 PH
208 Volts/60 Hz 82.3 48.4 10.3 6.7
230 Volts/60 Hz 75.5 44.4 10.3 6.7
460 Volts/60 Hz N/A 22.2 N/A 3.4
7KW Booster
208 Volts/60 Hz N/A 29.0
230 Volts/60 Hz N/A 25.0
460 Volts/60 Hz N/A 13.0
12KW Booster
208 Volts/60 Hz N/A 33.0
230 Volts/60 Hz N/A 29.0
460 Volts/60 Hz N/A 14.5
The maximum recommended distance between and
electric booster heater and the dishmac
18”
Note: All vertical dimensions are +/- 1/2” from finished
floor due to adjustable bullet feet.
Note: Utility connections are identical regardless of
direction of flow
.
Note: 7 KW and 12 KW booster
heaters are designed to supply dishmachine with rinse water at the appropriate temperature.
Note: Booster heaters require a separate electrical connection.
* - Models do not come with booster
heaters as standard equipment.
Amperage ratings are for mac
hine is 20”
30-1/2”
.
24”
hine only
8”
.
Cover
Drive
Motor
10”
60”
8”
C
4”
D
10”
2-1/4”
7”
All specifications subject to c
62”
hange without notice.
6”
Conveyors
Page 6
ConveyorsTSC-44 Drawing
8"
4 1/2"
8"
4"52"
10 1/2"
21" Opening
60"
4"w. x 16"lg cutout in
Vent Cowl/Splash Shield.
Shipped with Cover Plate.
Floor Sink Or Drain With
3" Minimum Drain Line
12 1/2"
25"
44"
Table to Table
6”
10” high backsplash on table
4-1/2”
B
all
W
A
between wall and dishmachine is 4”.
21”
25”
Add 3” to machine width to account for
conduit and/or piping on the back of the
machine when determining doorways
and entrances for the machine to fit
through.
Scrap Trough Fabrication
Minimum recommended distance
34”
20-1/2”
Scrap
Trough
14”
Please note that scrap trough’s, regardless of the
direction of travel, MUST be a minimum of 14” from
the edge of the tub.
1”
.jacksonmsc.com
www
1-888-800-5672
Re
commende
d Table Fabrication
8/0
-11 A 0
7
610-002-9
7
All specifications subject to change without notice.
0
4
Loading...