Page 1
Power/Connections
Approximate Total Load AMPS
208V / 60HZ / 3PH 51.8
208V / 60HZ / 1PH 88.3
230V / 60HZ / 3PH 47.8
230V / 60HZ / 1PH 81.5
460V / 60HZ / 3PH 23.9
Booster Heater Options
External 40°F Min. Rise KW AMPS
208V / 60HZ / 3PH 24 66.6
230V / 60HZ / 3PH 24 60.2
460V / 60HZ / 3PH 24 30.1
External 70°F Min. Rise KW AMPS
208V / 60HZ / 3 PH 36 100.0
230V / 60HZ / 3PH 36 90.4
460V / 60HZ / 3PH 36 45.2
Venting Requirements (CFM)
Input end
Output end 400
Total CFM 600
ater Requirements
W
Incoming Water Temperature (°F) 180
With 24 KW booster heater option (°F) 140
With 36 KW booster heater option (°F) 110
Gallons per hour:
Hi-temp sanitization 186
Gallons per rack:
Hi-temp sanitization 0.74
Prewash T
Wash Tank Capacity (Gallons) 20.4
Incoming W
Flow Pressure (PSI) 15-25
Flow Rate Minimum (GPM)
Drainline Size IPS (Minimum) (Inches) 1 1/2
ank Capacity (Gallons) 1
S) (Minimum) 1/2
aterline Sizes (I
Hi-temp sanitization 3.9
P
200
.25
7
TS-66 Traditional
Series
Standard Features
252 racks per hour hi-temp sanitizing
•
rinse.
• 0.74 gallons per rack hi-temp
sanitizing rinse.
• Incoming water pressure regulator
• Standard 18” clearance.
• Totally electro-mechanical; no solid
state controls utilized.
• Fully automatic including auto-fill.
• Completely self-draining stainless
steel wash pump.
• Exclusive “Energy Guard” controls
system operates wash and rinse
sections only when a rack is being
washed or rinsed.
• A long 16” wash section as well as
18” separation between wash and
rinse produces superior results.
• Convenient, externally operated
lever drain.
Performance/Capacities
Operating Capacity
Racks per hour
Hi-temp Sanitization 252
Dishes per hour
Hi-temp Sanitization 6300
Glasses per hour
hes)
6300
3/4
Hi-temp S
Steam Coil Tank Heat
Steam Connection I
Steam Flow Pressure (PSIG) 10-20
Consumption @ 15 PSIG (Lbs/hr) 60
Wash Pump Motor HP 2
Wash Pump Capacity (GPM) 270
Wash Tank KW 15
Prewash Pump Motor H
Prewash Pump Capacity (GPM) 120
Conveyor Motor Horsepower 1/4
Conveyor Speed (F
Hi-temp Sanitization 7.0
anitization
P
eet/minute)
S (Inc
P1
Stainless steel frame, legs, adjustable
•
bullet feet, and front appearance panel
are all standard.
• Standard 8” vent cowls/splash
shields on both wash and rinse ends
of the machine.
• Heavy gauge construction for extra
ruggedness and durability.
Operating Temperatures
Prewash Tank–°F 110 - 140
Wash Tank–°F (Minimum)
Hi-temp Sanitization 160
Rinse–°F (Minimum)
Hi-temp Sanitization 180
Dimensions (Inches)
Length between dishtables 66
Machine width 30-3/4
Wall Clearance (Minimum) 4
Cavity/dish clearance (Maximum) 18
Cavity width
Shipping Information
eight (Lbs)
W
Dimensions (Inc
Length 96
Depth 40
Height
olume (Cubic feet) 174
V
hes)
20-1/2
4
9
8
8
7
Conveyors
Page 2
TS-66 Traditional
Series
Specifications
NOTE:
The TS-66 series conveyor dishmachines are
SF International Inc. (NSF) and Underwriters
N
Laboratories Inc. (UL) listed. They also meet the requirements of A.S.S.E. Standard No. 1004.
PERFORMANCE:
conveyor dishwasher designed to wash, rinse, and sani
tize tableware and utensils commonly associated with
the preparation and consumption of food items in a commercial foodser
plished through hi-temp sanitization utilizing 180-195°F
fresh water rinse. The unit conveys standard 20” x 20”
dishracks first through a recirculatied (120 GPM) 110 140°F prewash and then through a recirculating detergent laden wash section where 270 gallons per minute
(GPM) of 160°F wash water is pumped over the dishrack
to remove the food soil. The rack is then conveyor driven
into a final rinse section where a fresh water final rinse
spray system removes residual detergent and sanitizes.
For hi-temp sanitizing, the unit must be installed to a
potable water line capable of supplying 186 gallons per
hour between 180-195°F at 15-25 PSI flow pressure for
maximum hourly rack capacity of 252 racks per hour.
CONSTRUCTION:
are 304 series stainless steel. No 400 series stainless
steel and/or plastics are utilized. Frame is constructed of
2” diameter stainless steel tubing formed and completely
saddle welded for superior strength. The wash tank, and
rinse chamber are formed and heliarc welded 16 gauge
#2B finish. Hood is 16 gauge #3 finish. Stainless steel
feet are adjustable ±1/2”.
PREWASH PUMP:
inside the prewash tub is totally stainless steel as is the
impeller. T
the motor. prewash water is recirculated from the pre
wash tank through the manifolds and prewash arm system
at the rate of 120 G
W
wash tub is tot
wash pump itself is totally integral with the motor. Wash
water is recirculated from the wash t
manifolds and wash arm system at the rate of 2
PR
enclosed, fan cooled type motor drives the wash pump
and arms. Single-phase motors are capacitor st
induction run with internal thermal overload protection.
Three-phase motors are induction run with external overload protection. Motor shaft is supported by permanently
lubricated grease pac
he prewash pump itself is tot
H PUMP:
AS
AS
EW
Fully automatic, single tank, rack
vice operation. Sanitization is accom-
All stainless steel components
Internal prewash pump located
ally integral with
M.
P
Internal wash pump located inside the
ainless steel as is the impeller. T
ally st
ank through the
0 G
7
P MOTOR:
M
H PU
ked ball bearings.
A 1 H
P tot
M.
P
ally
art,
ASH PUMP MOTOR:
W
fan cooled type motor drives the wash pump and arms.
Single-phase motors are capacitor start, induction run
with internal thermal overload protection. T
motors are induction run with external overload protection. Motor shaft is supported by permanently lubricated
ked ball bearings.
grease pac
-
CONVEY
through the machine by a center-mounted, heavy-duty
stainless steel pawl bar with stainless steel cast, counterweighted, wide surface pawls. The pawl bar is designed
to not interfere with spray patterns in the wash, and
rinse section. The pawl bar is driven by a 1/4 HP motor
and worm drive gear reduction unit. The conveyor motor
itself is totally enclosed, non-ventilated. Single-phase
motors are capacitor start, induction run with internal
thermal overload protection. Three-phase motors are
induction run with external overload protection. Pawl bar
conveyor drive unit is mounted on the left hand side of
the machine and is enclosed with a removable stainless
steel cover. Maximum conveyor speed is 7.0 feet per
minute for hi-temp machines.
CHAMBER:
of 18”.
CONTROLS:
control box mounted on top of the machine for ease of
access and increased reliability. Power “ON/OFF” switch
is the only manual switch required. “Energy Guard” fully
automates the machine and utilizes switching logic to
operate wash and rinse sections only when a rack is
being washed or rinsed as well as turning the conveyor
off when a rack exits the machine and there are no other
racks in the machine. Regardless of machine voltage, all
control circuitr
circuit transformer. The unit is completely wired with
-
105°C, 600V thermoplastic insulated wire and routed
through U
FILL:
automatic when the machine is initially energized. The
he
prewash tank fill line needs to be hooked up to a 110 140°F potable water line; the wash tank fill line needs to
be hooked up to a 180°F minimum potable water line
which normally would be supplied by an external booster
heater or our optional Hatco booster heater packages. Fill
is controlled by standard solenoid valves and vacuum
breaker assemblies. The incoming water solenoids are
activated by stainless steel float systems located in the
tanks for required maintenance of the water levels.
RECIRCULATING PREWASH:
tank itself has a 17.25 gallon capacity and maintains the
water level with a separate fill connection from the rest
OR SYSTEM: Racks are conveyed
The chamber has a standard clearance
Controls are located in a stainless steel
y will be operated from a 1
L approved conduit.
Initial fill of the prewash tank and wash tank is
A 2 H
P totally enclosed,
hree-phase
0 volt control
1
The prewash
Conveyors
of the mac
an internal float and an external solenoid valve. Washing
action is accomplished by recirculating water in the prewash t
prewash arms are easily removable and along with
removable end caps, are easily cleanable without the use
of tools.
R
has a 20.4 gallon capacity and maintains that level with
a skimming type overflow. Washing action is accomplished by recirculating detergent laden water in the
wash tank through upper and lower wash arms. Make-up
water comes from the final rinse section and is controlled at approximately 2 GPM. The arms themselves are
extended and create a longer wash section than competitive models. Wash section is automatically activated by
racks as they pass through. Wash arms, upper and lower,
contain 36 separate stripping nozzles for superior performance. All wash arms are easily removable and along
with removable wash arm end caps, are easily cleanable
without the use of tools. Large stainless steel strainer
pans, as well as a pump intake strainer for secondary
protection are readily accessible and removable for
cleaning purposes. Knockouts and connections are provided to allow easy installation of detergent concentration sensor and dispenser tubing by others.
FINAL RINSE:
the machine through a standard “Y” strainer, solenoid
valve, and approved vacuum breaker assembly and is
plumbed to upper and lower final rinse arms located at
the output end of the machine. Single rows of fan jet
nozzles are located on both rinse arms. Connection points
are provided for both rinse agent injection into the final
rinse line by others. Total final rinse flow rate is 3.9 GPM.
DRAIN, OVERFLOW, AND MAKE-UP:
machine is designed to maintain appropriate wash tank
water levels at all times even at low pressures. T
flow system is designed to automatically skim the surface of the wash tank. Make-up water from the final
rinse system not only replenishes the wash water but
also helps maintain appropriate water levels as well as
appropriate wash tank temperatures. A large lever located on the front panel of the machine operates a drain
valve and drains the machine completely.
PRESSURE REDUCING VALVE:
installed on incoming water line to control water pressure.
hine. The automatic fill is controlled through
ank through upper and lower prewash arms. All
ECIRCULATING WASH:The wash tank itself
Fresh pressurized rinse water enters
The
he over-
Factory
Page 3
Additional Standard
Equipment:
• Vent cowls/splash shields with 4” x 16” openings covered
with removable plates for connection to exhaust ducts
when required.
• Flexible strip curtains provided at the ends of the
vent cowls as well as at the ends of the machine and
separating the prewash, wash, power rinse, and final
rinse sections.
• Extra large inspection doors located on front of
machine for easy access and cleanability.
• Safety door switches shut down machine should any
door be opened during operation.
• Stainless steel front appearance panel.
• Positive low level water protection for wash and power
rinse tank heat.
• Sealed dial type thermometers for the wash and final
rinse temperatures.
Optional Mandatory
Specifications:
WASH TANK HEATING EQUIPMENT
(Choose One):
ELECTRIC:
elements mounted inside the wash tank and easily
removable from the outside. The heaters are protected
by a stainless steel float system as well as high limit
overload protection. Water temperature in the tanks is
controlled and maintained by fast reacting thermostats
h control the heating elements.
whic
STEAM:
injectors so that cont
the wash water is not an issue. Stainless steel tubular
steam coils are mounted inside the wash and power
rinse t
protected by a stainless steel float system. An external
steam “Y” strainer and high temperature steam solenoid
regulates the flow of steam through the coils.
Temperature in the tanks is controlled and maintained by
fast reacting thermost
the steam solenoids. A float and thermost
is provided and removes steam condensate from the
steam coils whic
pumped bac
is available. Steam coils require a minimum of 10 PSIG
flowing steam supply and a ma
with a steam pressure regulator (by others) if steam
supply exceeds 20 PSIG.
Low watt density 15 KW tubular heating
ainless steel coils are utilized rather than
St
aminated steam being injected into
s below the optimum water level. T
ank
ats which control the operation of
atic steam trap
h can either be plumbed to a drain or
k to the boiler if a condensate return system
ximum of 20 PSIG. Install
he coils are
Optional Features and
Accessories:
EXTERNAL 40°F ELECTRIC BOOSTER
EATER:
H
incoming 140°F water to a minimum of 180°F for hitemp sanitizing rinse. Custom features include castonelined t
as a pressure reducing valve. Unit is located next to the
output end of the machine, completely preplumbed.
ower to the booster heater requires a separate electrical
P
connection. Unless specified otherwise, electrical characteristics of the booster heater will be the same as that of
the dishwasher. The booster heater is available in
8/240/480 voltages/3 phase only.
20
XTERNAL 70°F RISE BOOSTER HEATER:
E
External 36 KW booster heater capable of boosting
incoming 110°F water a minimum of 70 degrees to a minimum of 180°F for hi-temp sanitizing rinse. Unit is located
next to the output end of the machine and comes completely preplumbed. Power to the booster heater requires
a separate electrical connection. Unless specified otherwise, electrical characteristics of the booster heater will
be the same as that of the dishwasher. The booster
heater is available in 208/240/480 voltages/3 phase only.
STEAM BOOSTER HEATER:
nected to a standard 110°F incoming water supply in
order to insure 180-195°F hi-temp sanitizing final rinse
requirements. Unit comes complete with steam “Y”
strainer and high temperature steam solenoid as well as a
steam pressure relief valve. Water temperature is controlled and maintained by a fast reacting thermostat
which controls the operation of the steam solenoid. A float
and thermost
steam condensate from the coil whic
plumbed to a drain or pumped back to a boiler if a condensate return system is available. Must be inst
a steam pressure regulator (by others) if steam supply
exceeds 20 PSIG.
TABLE LIMIT SWITCH:
and mounted to the bac
revents damage to conveyor drive system, rac
P
dishes due to racks backing up on the output end of the
mac
than 1
VE
x 7” high collars located on the vent cowls to allow easy
connection to an external exhaust system including a st
dard “pant-leg” t
lockable damper flap for fine tuning exhaust system to
remove appropriate C
50 CYCLE (HERTZ) ELECTRICAL
CHARA
External 24 K
ank, low water cutoff, pressure relief valve, as well
atic steam trap is provided and removes
hine. Highly recommended for clean dishtables less
0 feet in length.
WL COLLAR
NT CO
ype exhaust duct. Includes adjust
ISTICS:
R
TE
C
W booster heater boosts
Sized to be con-
h can either be
Factory wired to machine
splash of the table in the field.
k
S:
F
FM requirements.
Units are available in 5
actor
y inst
alled 4” x 1
alled with
s, and
k
an-
able and
0 H
6”
in the following voltages: 208V/1 or 3PH, 230V/1 or 3PH,
80V/3PH, and 460V/3PH. Units operating at 50 HZ are
3
not submitted for UL Listing.
SIDELOADER:
of conveyor machine. This feature allows the machine to
alled close to a corner and maximize dishroom
be inst
space. The sideloader option is available in both the
hooded and unhooded versions. See separate spec sheets
ails.
for det
XHAUST VENT FAN CONTROL:
E
Automatically turns exhaust vent fan on when rack
enters the machine. Delay timer also turns off the
exhaust vent fan 5-10 seconds after rack exits machine
when no other racks are being conveyed through the
machine.
FLANGED FEET:
permanent mounting to the floor is required. Fully
adjustable for required height.
WATER HAMMER ARRESTOR:
inside the supply line.
Z
Factory installed option on input end
Available for installations where
Installed
Page 4
TS-66 Traditional
Series
cifications
Spe
Note: Chec
TS-66 Series Rack Conveyor Dishwasher—Item No. ____________
Shall be a Jackson TS-66 series, single tank rack conveyor dishwasher.
Sanitization shall be accomplished by using:
______ Hi-temp (180°F minimum) sanitizing rinse
Electrical characteristics shall be:
______ 208V/60HZ/3PH ______ 208V/50HZ/3PH
______ 208V/60HZ/1PH ______ 208V/50HZ/1PH
______ 230V/60HZ/3PH ______ 230V/50HZ/3PH
______ 230V/60HZ/1PH ______ 230V/50HZ/1PH
______ 460V/60HZ/3PH
Wash tank heating shall be a minimum of 160°F for hi-temp applications
and accomplished by:
______ 15 KW electric heating elements thermostatically controlled.
______ Stainless steel steam coils thermostatically controlled.
Direction of rack flow shall be (when standing in front of machine):
______ Right-to-Left ______ Left-to-Right
k and/or copy all that apply.
Conveyors
Unit shall have the following features:
252 racks per hour utilizing 0.74
•
gallons of water per rack for
hi-temp sanitizing rinse.
• Incoming water pressure regulator.
• Standard 18" clearance
throughout machine.
• Exclusive “Energy Guard” controls system energizes prewash,
wash, recirculating rinse, and
final rinse sections only when a
rack is in place.
• Completely electro-mechanical;
no solid-state controls.
• Fully automatic operation including auto-fill.
• Stainless steel wash pump
and impeller and completely
self-draining.
Convenient, externally operated
•
lever drain.
• Vent cowls/splash shields with
extra curtains on both wash and
rinse ends of the machine.
• Stainless steel frame, legs,
adjustable bullet feet, and front
appearance panel.
• All 304 series stainless steel
construction; no 400 series
stainless steel and no plastics
utilized.
Unit shall have the following features as optional extras:
______ External electric 24 KW booster heater for a minimum 40°F rise
and available in the following voltages:
0HZ/3PH
0 or 6
______ 20
______ 240V/50 or 60HZ/3PH
______ 4
______ External electric 36 KW booster heater for a minimum 70°F rise
and available in the following volt
______ 208V/50 or 60HZ/3PH
______ 240V/50 or 60HZ/3PH
______ 4
______ Steam booster heater.
______ Exhaust fan control controls external exhaust fan power and
duration time.
______ Flanged feet for permanent in-place mounting to the floor.
8V/5
/3PH
Z
0H
0 or 6
0V/5
8
80V/50 or 60HZ/3PH
ages:
• Wash section must be a minimum of 16” in length as well as
18” separation between recirculating wash and final rinse.
______ Table limit switch completely prewired and extending from the
output end of the machine, 15’0” long.
______ Whisker-style switch
______ Striker plate switch
______ Photosensor switc
______ Inst
______ Incoming water hammer arrestor inst
______ Sideloader installed on input end of machine.
alled 4" x 16" x 7" high vent cowl collars for easy connection
to an external exhaust system and including adjustable and lockable damper flaps.
______ output end only ______ input end only
______ both ends
______ unhooded sideloader ______ hooded sideloader
h
alled.
.jacksonmsc.com
www
1-888-800-5672
All specifications subject to change without notice.
0
4A 8/0
-6
7
610-002-9
7
4
Page 5
TS-66 Traditional
Series
Left to Right Operation Shown
Legend to Drawing
A– Machine water inlet 1/2” I.P.S., 180°F minimum, 61-
1/4” above finished floor
B– Electrical connection , approximately 61-1/4” above
finished floor. See table for amperage requirements
C– Drain connection-1 1/2” I.P.S.
D– Prewash water inlet 1/2” I.P.S. 110°F- 140°F
*E–Condensate return connection, 3/4” FPT (return to
boiler feeder or open drain)
*F– Incoming low pressure steam connection, 3/4” FPT
(gate valve supplied)
*Steam tank heat option only
Note: All vertical dimensions are +/- 1/2” from floor due
to adjustable bullet feet
1-PH 3-PH 1-PH 3-PH *3-PH
208 Volts 60 Cycles 88.3 51.8 18.3 10.1 66.6
230 Volts 60 Cycles 81.5 47.8 18.3 10.1 60.2
460 Volts 60 Cycles N/A 23.9 N/A 5.1 30.1
TS-66 Series
Electrical Data
Approximate Total Load Amps
Electric Tank Heat Steam Tank Heat Optional 24 KW
Models: Models: Electric
TS-66 TS-66S Booster Heater
Recommended Table Fabrication
82”
66” TABLE TO TABLE
22”
5”
13”
61-1/4”
34”
11-1/4”
10”
29”
5”
4-1/2”
6-1/2”
53”
66”
8”
66”
TABLE TO TABLE
8”
12-1/2”
4”
74”
82”
4”
Floor sink or drain with
3” minimum drain line.
26”
8”
10-1/2”
21”
OPENING
4” wide x 16” long cutout in vent
cowl/splash shield. Shipped with
cover plates.
34”
14”
Drive
Motor
Cover
10” high backsplash
Scrap trough location MUST be a
minimum of 14” from the tub,
regardless of which side the trough
is mounted on.
Scrap Trough Location
Optional 36 KW
Electric
Booster Heater
*3-PH
99.9
90.4
45.2
30-1/2”
24”
18”
The maximum recommended distance between any electric
booster heater and the dishmachine is 20 ft.
B
C
E
F
A
D
25”
21”
4”
5-3/4”
WALL
Add 3” to machine width to account for conduit and/or piping on the back of the machine
when determining doorways and entrances
for the machine to fit through.
All specifications subject to change without notice.
20-1/2”
1”
* Option electric boosters come in 3 phase only.
Note: Optional booster heater requires separate electrical connection. 24
KW and 36 KW booster heaters are designed to supply the dishmachine
with rinse water at the appropriate temperature. Models do NOT come
with booster heaters as standard equipment.
Machine height with doors open is 72”.
TS-66 Drawings Rev A.qxd 10/15/04 9:52 AM Page 1
Page 6
TS-66 Traditional
Series
Right to Left Operation Shown
07610-002-97-65A 8/04
All specifications subject to change without notice.
Recommended Table Fabrication
66”
TABLE TO TABLE
8”
12-1/2”
4”
74”
82”
4”
Floor sink or drain with
3” minimum drain line.
26”
8”
10-1/2”
21”
OPENING
4” wide x 16” long cutout in vent
cowl/splash shield. Shipped with
cover plates.
1-PH 3-PH 1-PH 3-PH *3-PH
208 Volts 60 Cycles 88.3 51.8 18.3 10.1 66.6
230 Volts 60 Cycles 81.5 47.8 18.3 10.1 60.2
460 Volts 60 Cycles N/A 23.9 N/A 5.1 30.1
TS-66 Series
Electrical Data
Approximate Total Load Amps
Electric Tank Heat Steam Tank Heat Optional 24 KW
Models: Models: Electric
TS-66 TS-66S Booster Heater
Optional 36 KW
Electric
Booster Heater
*3-PH
99.9
90.4
45.2
* Option electric boosters come in 3 phase only.
Note: Optional booster heater requires separate electrical connection. 24
KW and 36 KW booster heaters are designed to supply the dishmachine
with rinse water at the appropriate temperature. Models do NOT come
with booster heaters as standard equipment.
30-1/2”
24”
18”
The maximum recommended distance between any electric
booster heater and the dishmachine is 20 ft.
All specifications subject to change without notice.
25”
21”
5-3/4”
WALL
4”
61-1/4”
34”
11-
4-1/2”
6-1/2”
24”
10”
53”
66”
8”
3”
66” TABLE TO TABLE
82”
22”
5”
5”
20-1/2”
1”
10” high backsplash
14”
34”
Scrap trough location MUST be a
minimum of 14” from the tub,
regardless of which side the trough
is mounted on.
Scrap Trough Location
Machine height with doors open is 72”.
Drive
Motor
Cover
Legend to Drawing
A– Machine water inlet 1/2” I.P.S., 180°F minimum, 61-
1/4” above finished floor
B– Electrical connection , approximately 61-1/4” above
finished floor. See table for amperage requirements
C– Drain connection-1 1/2” I.P.S.
D– Prewash water inlet 1/2” I.P.S. 110°F- 140°F
*E–Condensate return connection, 3/4” FPT (return to
boiler feeder or open drain)
*F– Incoming low pressure steam connection, 3/4” FPT
(gate valve supplied)
*Steam tank heat option only
Note: All vertical dimensions are +/- 1/2” from floor due
to adjustable bullet feet
A
D
C
E
F
B
TS-66 Drawings Rev A.qxd 10/15/04 9:52 AM Page 2
Loading...