INTRODUCTION
ISP Technologies presents its newest edition to the rapidly growing Bass Vector
family. Now you can get the same great Bass Vector performance, in a smaller
and more compact package! Combining the low frequency extension that only
an 15” driver can achieve with the natural, extended (but not brittle) highs of
dual 8” drivers, the Bass Vector 115 cabinet achieves a balance of depth,
impact, and definition that makes 4x10’s sound lifeless in comparison!
Available in active and passive versions, a single active cabinet delivers 600
watts to its speakers. When an additional passive cabinet is connected, the
amplifier delivers a total of 1000 watt RMS to the two cabinets. The total
system power can be further increased by adding additional active and passive
cabinets. There is a limit of one passive cabinet per active cabinet.
The ISP Beta Bass Preamplifier is the ideal ‘head’ for the system, or the active
cabinet can be used with other bass heads when driven from their line output,
and the passive cabinet can be driven from virtually any powered bass head.
The high performance 15” driver is complemented by an advanced cabinet
design featuring optimum volume and a large, deep tuned port. This helps to
minimize the non-linear behavior and reduced low frequency output that small
ports produce. The cabinet is tour grade, with Baltic Birch plywood
construction, dadoed joints, extremely durable rubberized polyurethane finish,
metal handle, and casters.
PRECAUTIONS
NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE
YEARS OF TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL HANDELING.
All warnings on this equipment and in the operation instructions should be
adhered to and all operating instructions should be followed.
Do not use this equipment near water. Care should be taken so that objects do
not fall onto and liquids are not spilled into the unit through any openings.
The power cord should be unplugged from the outlet when the unit is left
unused for a long period of time.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. THIS EQUIPMENT SHOULD
BE SERVICED BY QUALIFIED SERVICE PERSONNELL ONLY. DO NOT MAKE
ANY INTERNAL ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT ANY
TIME. DO NOT TAMPER WITH INTERNAL ELECTRONIC COMPONENTS AT ANY
TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID THE
WARRANTY OF THIS EQUIPMENT, AND MAY CAUSE A SHOCK HAZZARD.
POWER REQUIREMENTS
This unit requires connection to a 120-volt AC outlet. Do not cut or disconnect
the ground pin on the power cord. Do not attempt to connect this unit to any
power source other than the specified 120VAC.
BASS VECTOR 115 CABINET BACK PANEL CONNECTIONS
1. POWER JACK
This switch controls the power to the amp module. This switch has only two positions
up is on and down is off.
2. POWER INLET MODULE
This module provides a connection for the power cord and also houses the main fuse.
(See the fuse replacement section)
3. INPUT SENSITIVITY
This control determines the overall input level of the signal to the power amp of the
bass vector. This will not affect the level of the signal passing through the output
connectors.
4. BALANCED ¼ INPUT
This jack provides an input for balanced or unbalanced line level signal source.
5. BALANCED XLR INPUT
This female connector provides an input for balanced line level signal source.
6. BALANCED ¼ OUTPUT
This jack provides a balanced loop through for connecting to additional powered
cabinets.
7. BALANCED XLR OUTPUT
This male connecter provides a balanced loop through for connecting to additional
powered cabinets.
SPEAKON CONNECTOR
This speakon connector can be found on the back panel of the
Bass Vector Passive cabinets. Connect to the corresponding
Neutrik speakon connector of the Bass Vector Active cabinets.
FUSE REPLACEMENT
1. Use a small screwdriver as shown to slide the fuse
cover out from the power inlet module. The fuse can
be found inside the fuse cover module after it is
pulled out.
NOTE: A SMALL COMPARTMENT IS ALSO
PROVIDED WITHIN THE FUSE COVER
MODULE FOR STORING A SPARE FUSE.
2. After replacing the fuse with another of identical
specifications, push the fuse cover module fully back
into place, ensuring that the fuse has snapped onto
the fuse holder inside the power inlet module.
LF DRIVER:
1 X 15 inch, large excursion, 450 watt RMS.
HF DRIVERS:
2 x 8 inch, high sensitivity, 250 watt RMS.
SENSITIVITY:
98dB @ 100 Hz, 102dB @ 1KHz (1 watt at 1
meter.
SPL:
125dB @ 1 meter, long term.
(128dB PRO VERSION)
129dB @ 1 meter, peak.
(132dB PRO VERSION)
FREQUENCY RANGE:
35Hz to 5KHz (-10dB).
FREQUENCY RESPONSE:
45Hz to 4KHz (+-3dB).
AMPLIFIER POWER:
1000 watt RMS, high current DCAT, fan
cooled.
REQUIRED POWER:
5 amps x 120 VAC typical, 10 amps max.
CONSTRUCTION:
Baltic Birch plywood extensively braced.
FINISH:
Rubberized Polyurethane.
DIMENSIONS:
30”W x 19.25”H x 18.75”D (without casters).
WEIGHT:
Active: 104 lbs., Passive: 89 lbs.
BASS VECTOR 115 SPECIFICATIONS
WARRANTY AND SERVICE
The Internal Circuitry is fully guaranteed to be free of defects under normal use and service
for a period of three years from the date of purchase. The Speakers and Cabinet that are
used in this product are fully guaranteed to be free of defects in parts and labor (including
speakers) under normal use and service for a period of 3 years.
Any damage resulting from the misuse or the failure to follow the precautions and
instructions will void the warranty.
In the event that the unit needs to be repaired, please return the unit to ISP Technologies
directly. Simply repack the unit, send a copy of the original receipt, a note stating the
problem, and send it to:
ISP Technologies, LLC
5479 Perry Drive Unit B
Waterford, MI 48329
Attn: Repair Dept.
All shipping charges must be fully prepaid.
ISP will not be responsible for any damages incurred in shipping of any unit. Any claim will
need to be settled with the shipping company.
The warranty will be voided if the serial number has been tampered with in any way.
The warranty card must also be filled out and returned in order to activate the warranty.
Should you have any questions for the repair department prior to returning the product
please call 1-(248)-673-7790
NOTE: This Product may be covered under one or more of the following patents or patents
pending: 7,035,413; 6,944,305; 6,931,134; 6,831,514; 6,091,013
ISP TECHNOLOGIES, LLC
5479 PERRY DRIVE UNIT B
WATERFORD, MI. 48329
248-673-7790
FAX: 248-673-7696
www.isptechnologies.com
Loading...