IPSO IHC030, IHC012, IHC035, IHC018, IHC025 User Manual

On-Premise

Laundry

Planning

Handbook

5-08-52R1 June 2011

CHM2097N

IHC Washer-Extractors

Refer to Installation manual for full instructions.

Table of

Contents

Washer-Extractors................................................................... 2

Introduction............................................................................ 2

Model Identification - IHC Washer-Extractors.................. 2

Specifications and Dimensions - Model IHC012 ................... 3

Specifications and Dimensions - Model IHC018 ................... 7

Specifications and Dimensions - Model IHC025 ................... 11

Specifications and Dimensions - Model IHC030 ................... 15

Specifications and Dimensions - Model IHC035 ................... 19

Installation - IHC Models ....................................................... 23

means without the expressed written consent of the publisher.

1

5-08-51

Washer-Extractors

Introduction

Model Identification - IHC Washer-Extractors

Figure 1

IHC012 IHC025 IHC035

IHC018 IHC030

CHM2097N

5-08-52

2

Washer-Extractors

Specifications and Dimensions - Model IHC012

Capacity (dry weight) Ratio (kg/l)

1:11

1:10

1:9

Cylinder

Cylinder diameter, in. (mm)

Cylinder depth, in. (mm)

Cylinder volume, ft.3 (l)

Cabinet

Overall height, in. (mm)

Overall width, in. (mm)

Overall depth, in. (mm)

Front Loading

Door opening size, in. (mm)

Height of door bottom above floor, in (mm)

Height of door center above floor, in (mm)

Speed

Was h

Distribution

Spin

G-factor

High Spin

Motor (3 phase), 4p, 1470 tr/min

Drain Valve, in. (mm)

Water Supply (hard, soft, warm water), in. (mm)

Direct Steam Heating

Steam inlet connection size, in. (mm)

Electrical

Electrical Heating (230/400 V)

Electrical Heating (400V)

Steam

Warm Water (without additional heating)

Warm Water (with additional heating)

Packing Dimensions (height X width X depth), in. (mm)

Weight

Net weight, lb. (kg)

Gross weight, lb. (kg)

11.02 lb. (5 kg)

12.13 lb. (5.5 kg)

13.45 lb. (6.1 kg)

20.87 (530)

9.84 (250)

1.94 (55)

40.87 (1038)

25.98 (660)

22.64 (575)

11.81 (300)

10.98 (279)

19.88 (505)

10-50 tr/min - RPM

85 tr/min - RPM

250-1250 tr/min - RPM

462

0.74 HP/0.55 kW

2 (51)

.75 (19)

Not Applicable

4.2 kW

6 kW

Not Applicable

44.88 X 29.13 X 33.07 (1140 X 740 X 840)

405.65 (184)

436.52 (198)

3

5-08-52

Machine Dimensions - Model IHC012

CHM2100N

CHM220

40.87 in. (1038 mm)

39.8 in. (1011 mm)

25.98 in. (660 mm)

6.4 in.

(163 mm)

20.87 in. (530 mm)

1.3 in.

(33 mm)

10.98 in.

(279 mm)

25.98 in. (660 mm)

1.18 in.

(30 mm)

2.72 in.

(69 mm)

19.09 in. (485 mm)

22.24 in. (565 mm)

24.49 in. (622 mm)

CHM2201N

CHM2200N

CHM2202N

8.9 in.

(226 mm)

2.95 in.

(75 mm)

5.94 in.

(151 mm)

34.92 in. (887 mm)

31.14 in. (791 mm)

29.41 in. (747 mm)

2.76 in.

(70 mm)

27.41 in. (696.2 mm)

4.3 in.

(109 mm)

7.09 in.

(180 mm)

1.73 in.

(44 mm)

1

2

4

9

6

3

7

8

10

5

2.56 in.

(65 mm)

1.3 in.

(33 mm)

2.56 in.

(65 mm)

1.18 in.

(30 mm)

Washer-Extractors

1 Ventilation Soap Dispenser 6 Electrical Connections 2 Warm Water Connections .75 in. 7 Ventilation Tub 3 Liquid Soap Connections 8 Drain Valve 4 Soft Water Connections .75 in. 9 Bolt Pattern for Fixation of the Machine 5 Main Switch 10 Hard Water Connections .75 in.

5-08-52

Figure 2

4

Washer-Extractors

2.56 in.

(65 mm)

20.87 in. (530 mm)

21.46 in. (545 mm)

19.09 in. (485 mm)

1.18 in.

(30 mm)

ø0.71 in.

(ø18 mm)

1.18 in.

(30 mm)

2.56 in.

(65 mm)

25.98 in. (660 mm)

Mounting Bolt Hole Locations - Model IHC012

Figure 3

CHM2203N

5

5-08-52

Electrical Installation Requirements - Model IHC012

Only trained personnel should perform this procedure. Use caution while servicing machines with covers removed and power applied.

W700

WARNING

Washer-Extractors

Boiler Fed/Steam Heat Electric Heat

Recommended

Circuit Breaker

Code

N 440-480 50/60 3 3+PE 3 10 10 14/2.5

P 380-415 50/60 3 3+N+PE 7 15 16 14/2.5 16 20 20

Q 200-240 50/60 3 3+PE 7 15 16 14/2.5 23 30 32

X 200-240 50/60 1/3 2/3+PE 7 15 16 14/2.5 N/A N/A N/A

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 13 15 16

Q 200-240 50/60 3 3+PE 18 20 20

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

Voltage

Cycle

Phase

Wire

Full Load

Amps

(US-market)

US NON-US US NON-US

Table 1

AWG/mm

2

Heating Elements

kW Standard

Full Load

Amps

N/A N/A N/A

3x2 kW

Alternative Electric Heat Options

N/A N/A N/A

3x1.4 kW

Circuit Breaker

(US-market)

Recommended

AWG/mm

2

N/A

12/4.0

10/6.0

N/A

14/2.5

12/4.0

N/A

5-08-52

6

Washer-Extractors

Specifications and Dimensions - Model IHC018

Capacity (dry weight) Ratio (kg/l)

1:11

1:10

1:9

Cylinder

Cylinder diameter, in. (mm)

Cylinder depth, in. (mm)

Cylinder volume, ft.3 (l)

Cabinet

Overall height, in. (mm)

Overall width, in. (mm)

Overall depth, in. (mm)

Front Loading

Door opening size, in. (mm)

Height of door bottom above floor, in (mm)

Height of door center above floor, in (mm)

Speed

Was h

Distribution

Spin

G-factor

High Spin

Motor (3 phase), 4p, 1470 tr/min

Drain Valve, in. (mm)

Water Supply (hard, soft, warm water), in. (mm)

Direct Steam Heating

Steam inlet connection size, in. (mm)

Electrical

Electrical Heating (230/400 V)

Electrical Heating (400V)

Steam

Warm Water (without additional heating)

Warm Water (with additional heating)

Packing Dimensions (height X width X depth), in. (mm)

Weight

Net weight, lb. (kg)

Gross weight, lb. (kg)

15.21 lb. (6.9 kg)

16.76 lb. (7.6 kg)

18.52 lb. (8.4 kg)

20.87 (530)

13.58 (345)

2.68 (76)

40.87 (1038)

25.98 (660)

29.09 (739)

11.81 (300)

10.98 (279)

19.88 (505)

10-50 tr/min - RPM

85 tr/min - RPM

250-1000 tr/min - RPM

296

1.01 HP/0.75 kW

2 (51)

.75 (19)

.38 (10)

4.2 kW - 6 kW - 9 kW

12 kW

Not Applicable

44.88 X 29.13 X 33.07 (1140 X 740 X 840)

465.18 (211)

513.68 (233)

7

5-08-52

Machine Dimensions - Model IHC018

CHM2204N

CHM2

40.87 in. (1038 mm)

39.8 in. (1011 mm)

25.98 in. (660 mm)

8.66 in.

(220 mm)

20.87 in.

(530 mm)

1.3 in.

(33 mm)

10.98 in.

(279 mm)

25.98 in.

(660 mm)

1.3 in.

(33 mm)

1.18 in.

(30 mm)

2.72 in.

(69 mm)

23.23 in.

(590 mm)

26.38 in.

(670 mm)

28.62 in.

(727 mm)

CHM2205N

CHM2204N

CHM2206N

8.9 in.

(226 mm)

2.95 in.

(75 mm)

5.94 in.

(151 mm)

34.92 in. (887 mm)

31.14 in. (791 mm)

29.41 in. (747 mm)

19.1 in. (485 mm)

27.41 in. (696.2 mm)

4.3 in.

(109 mm)

2.76 in.

(70 mm)

7.09 in.

(180 mm)

1.73 in.

(44 mm)

1

2

4

8

6

3

7

9

10

5

2.56 in.

(65 mm)

2.56 in.

(65 mm)

1.18 in.

(30 mm)

Washer-Extractors

1 Ventilation Soap Dispenser 6 Electrical Connections 2 Warm Water Connections .75 in. 7 Ventilation Tub 3 Liquid Soap Connections 8 Drain Valve 4 Soft Water Connections .75 in. 9 Steam Connections 5 Main Switch 10 Hard Water Connections .75 in

5-08-52

Figure 4

8

Washer-Extractors

CHM2207N

1.18 in.

(30 mm)

20.87 in. (530 mm)

1.18 in.

(30 mm)

ø0.71 in.

(ø18 mm)

25.59 in. (650 mm)

23.23 in. (590 mm)

2.56 in.

(65 mm)

25.98 in. (660 mm)

2.56 in.

(65 mm)

Mounting Bolt Hole Locations - Model IHC018

Figure 5

CHM2207N

9

5-08-52

Electrical Installation Requirements - Model IHC018

Only trained personnel should perform this procedure. Use caution while servicing machines with covers removed and power applied.

W700

WARNING

Washer-Extractors

Boiler Fed/Steam Heat Electric Heat

Recommended

Circuit Breaker

Code

N 440-480 50/60 3 3+PE 4 10 10 14/2.5

P 380-415 50/60 3 3+N+PE 12 15 16 14/2.5 21 30 25

Q 200-240 50/60 3 3+PE 12 15 16 14/2.5 27 30 32

X 200-240 50/60 1/3 2/3+PE 12 15 16 14/2.5 N/A N/A N/A

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 18 20 20

Q 200-240 50/60 3 3+PE 23 30 25

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

N 440-480 50/60 3 3+PE

Voltage

Cycle

Phase

Wire

Full Load

Amps

(US-market)

US NON-US US NON-US

AWG/mm

2

Heating Elements

kW Standard

Full Load

Amps

N/A N/A N/A

3x2 kW

Alternative Electric Heat Options

N/A N/A N/A

3x1.4 kW

N/A N/A N/A

Circuit Breaker

(US-market)

Recommended

AWG/mm

2

N/A

10/6.0

N/A

12/4.0

10/6.0

N/A

P 380-415 50/60 3 3+N+PE 25

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE

Q 200-240 50/60 3 3+PE N/A N/A N/A

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

5-08-52

Table 2

3x3 kW

3x4 kW

35

21

29

30 32

40 40

30 25

40 32

10/6.0

8/10.0

N/A

10/6.0

8/10.0

N/A

10

Washer-Extractors

Specifications and Dimensions - Model IHC025

Capacity (dry weight) Ratio (kg/l)

1:11

1:10

1:9

Cylinder

Cylinder diameter, in. (mm)

Cylinder depth, in. (mm)

Cylinder volume, ft.3 (l)

Cabinet

Overall height, in. (mm)

Overall width, in. (mm)

Overall depth, in. (mm)

Front Loading

Door opening size, in. (mm)

Height of door bottom above floor, in (mm)

Height of door center above floor, in (mm)

Speed

Was h

Distribution

Spin

G-factor

High Spin

Motor (3 phase), 4p, 1470 tr/min

Drain Valve, in. (mm)

Water Supply (hard, soft, warm water), in. (mm)

Direct Steam Heating

Steam inlet connection size, in. (mm)

Electrical

Electrical Heating (230/400 V)

Electrical Heating (400V)

Steam

Warm Water (without additional heating)

Warm Water (with additional heating)

Packing Dimensions (height X width X depth), in. (mm)

Weight

Net weight, lb. (kg)

Gross weight, lb. (kg)

18.96 lb. (8.6 kg)

20.94 lb. (9.5 kg)

23.15 lb. (10.5 kg)

20.87 (530)

17.32 (440)

3.35 (95)

40.87 (1038)

25.98 (660)

33.03 (839)

11.81 (300)

10.98 (279)

19.88 (505)

10-50 tr/min - RPM

85 tr/min - RPM

250-1000 tr/min - RPM

296

1.01 HP/0.75 kW

2 (51)

.75 (19)

.38 (10)

4.2 kW - 6kW - 9 kW

12 kW

Not Applicable

49.21 X 29.13 X 37.40 (1250 X 740 X 950)

520.29 (236)

568.79 (258)

11

5-08-52

Machine Dimensions - Model IHC025

CHM

CHM2204N

40.87 in. (1038 mm)

39.8 in. (1011 mm)

25.98 in. (660 mm)

8.66 in.

(220 mm)

20.87 in.

(530 mm)

1.3 in.

(33 mm)

10.98 in.

(279 mm)

25.98 in.

(660 mm)

2.56 in. (65 mm)

2.72 in.

(69 mm)

27.16 in.

(690 mm)

30.31 in.

(770 mm)

32.56 in.

(827 mm)

CHM2209N

CHM2204N

CHM2206N

1.18 in.

(30 mm)

8.9 in.

(226 mm)

2.95 in.

(75 mm)

5.94 in.

(151 mm)

34.92 in.

(887 mm)

31.14 in.

(791 mm)

29.41 in.

(747 mm)

19.1 in. (485 mm)

27.41 in. (696.2 mm)

4.3 in.

(109 mm)

7.09 in.

(180 mm)

1.73 in.

(44 mm)

1

2

4

8

6

3

7

9

10

1.3 in.

(33 mm)

2.56 in.

(65 mm)

1.18 in.

(30 mm)

2.76 in.

(70 mm)

5

Washer-Extractors

1 Ventilation Soap Dispenser 6 Electrical Connections 2 Warm Water Connections .75 in. 7 Ventilation Tub 3 Liquid Soap Connections 8 Drain Valve 4 Soft Water Connections .75 in. 9 Steam Connections 5 Main Switch 10 Hard Water Connections .75 in

5-08-52

Figure 6

12

Washer-Extractors

CHM2211N

1.18 in.

(30 mm)

20.87 in.

(530 mm)

1.18 in.

(30 mm)

27.17 in.

(690 mm)

29.53 in.

(750 mm)

ø0.71 in.

(ø18 mm)

25.98 in.

(660 mm)

2.56 in.

(65 mm)

2.56 in.

(65 mm)

Mounting Bolt Hole Locations - Model IHC025

Figure 7

CHM2211N

13

5-08-52

Electrical Installation Requirements - Model IHC025

Only trained personnel should perform this procedure. Use caution while servicing machines with covers removed and power applied.

W700

WARNING

Washer-Extractors

Boiler Fed/Steam Heat Electric Heat

Recommended

Circuit Breaker

Code

N 440-480 50/60 3 3+PE 4 10 10 14/2.5

P 380-415 50/60 3 3+N+PE 12 15 16 14/2.5 21 30 25

Q 200-240 50/60 3 3+PE 12 15 16 14/2.5 27 30 32

X 200-240 50/60 1/3 2/3+PE 12 15 16 14/2.5 N/A N/A N/A

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 18 20 20

Q 200-240 50/60 3 3+PE 23 30 25

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

N 440-480 50/60 3 3+PE

Voltage

Cycle

Phase

Wire

Full Load

Amps

(US-market)

US NON-US US NON-US

AWG/mm

2

Heating Elements

kW Standard

Full Load

Amps

N/A N/A N/A

3x2 kW

Alternative Electric Heat Options

N/A N/A N/A

3x1.4 kW

N/A N/A N/A

Circuit Breaker

(US-market)

Recommended

AWG/mm

2

N/A

10/6.0

N/A

12/4.0

10/6.0

N/A

P 380-415 50/60 3 3+N+PE 25

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 29

Q 200-240 50/60 3 3+PE N/A N/A N/A

X 200-240 50/60 1/3 2/3+PE N/A N/A N/A

5-08-52

Table 3

3x3 kW

3x4 kW

30 32

35

21 30 25

40 40

40 32

10/6.0

8/10.0

N/A

10/6.0

8/10.0

N/A

14

Washer-Extractors

Specifications and Dimensions - Model IHC030

Capacity (dry weight) Ratio (kg/l)

1:11

1:10

1:9

Cylinder

Cylinder diameter, in. (mm)

Cylinder depth, in. (mm)

Cylinder volume, ft.3 (l)

Cabinet

Overall height, in. (mm)

Overall width, in. (mm)

Overall depth, in. (mm)

Front Loading

Door opening size, in. (mm)

Height of door bottom above floor, in (mm)

Height of door center above floor, in (mm)

Speed

Was h

Distribution

Spin

G-factor

High Spin

Motor (3 phase), 4p, 1470 tr/min

Drain Valve, in. (mm)

Water Supply (hard, soft, warm water), in. (mm)

Direct Steam Heating

Steam inlet connection size, in. (mm)

Electrical

Electrical Heating (230/400 V)

Electrical Heating (400V)

Steam

Warm Water (without additional heating)

Warm Water (with additional heating)

Packing Dimensions (height X width X depth), in. (mm)

Weight

Net weight, lb. (kg)

Gross weight, lb. (kg)

26.46 lb. (12 kg)

29.10 lb. (13.2 kg)

31.97 lb. (14.5 kg)

25.59 (650)

15.75 (400)

4.66 (132)

47.32 (1202)

30.71 (780)

33.15 (842)

11.81 (300)

14.78 (376)

23.82 (605)

10-50 tr/min - RPM

85 tr/min - RPM

250-1000 tr/min - RPM

363

2.01 HP/1.5 kW

2 (51)

.75 (19)

.38 (10)

12 kW - 15 kW - 18 kW

21 kW - 24 kW

Not Applicable

51.57 X 33.46 X 37.01 (1310 X 850 X 940)

716.50 (325)

782.64 (355)

15

5-08-52

Machine Dimensions - Model IHC030

CHM2212N

47.32 in. (1202 mm)

46.3 in. (1176 mm)

25.98 in.

(660 mm)

3.47 in.

(88 mm)

8.66 in.

(220 mm)

25.51 in. (648 mm)

1.34 in.

(34 mm)

14.78 in.

(376 mm)

30.71 in. (780 mm)

1.44 in.

(36.5 mm)

3.23 in.

(82 mm)

26.18 in.

(665 mm)

29.92 in.

(760 mm)

32.13 in.

(816 mm)

CHM2213N

CHM2212N

CHM2214N

13.05 in.

(332 mm)

7.93 in.

(202 mm)

10.49 in.

(267 mm)

38.11 in.

(968 mm)

36.81 in.

(935 mm)

35.16 in.

(893 mm)

20.87 in.

(530 mm)

33.17 in.

(843 mm)

4.3 in. (109.2 mm)

7.87 in.

(200 mm)

2.76 in.

(70 mm)

2.36 in.

(60 mm)

1

2

4

8

6

3

7

9

10

5

2.6 in.

(66 mm)

1.34 in.

(34 mm)

2.6 in.

(66 mm)

4.13 in.

(105 mm)

1.38 in.

(35 mm)

1.44 in.

(36.5 mm)

Washer-Extractors

CHM2213N

1 Ventilation Soap Dispenser 6 Electrical Connections 2 Warm Water Connections .75 in. 7 Ventilation Tub 3 Hard Water Connections .75 in 8 Drain Valve 4 Soft Water Connections .75 in. 9 Steam Connections 5 Main Switch 10 Liquid Soap Connections

5-08-52

Figure 8

16

Washer-Extractors

1.44 in.

(36.5 mm)

25.51 in.

(648 mm)

26.18 in.

(665 mm)

29.06 in.

(738 mm)

2.58 in.

(66 mm)

30.71 in.

(780 mm)

2.62 in.

(66 mm)

1.44 in.

(36.5 mm)

ø0.71 in.

(ø18 mm)

Mounting Bolt Hole Locations - Model IHC030

Figure 9

CHM2215N

17

5-08-52

Electrical Installation Requirements - Model IHC030

Only trained personnel should perform this procedure. Use caution while servicing machines with covers removed and power applied.

W700

WARNING

Washer-Extractors

Boiler Fed/Steam Heat Electric Heat

Recommended

Circuit Breaker

Code

N 440-480 50/60 3 3+PE 6 15 10 14/2.5

P 380-415 50/60 3 3+N+PE 18 20 20 12/4.0 36 40 40

Q 200-240 50/60 3 3+PE 18 20 20 12/4.0 49 60 60

X 200-240 50/60 1/3 2/3+PE 18 20 20 12/4.0 N/A N/A N/A

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 40 50 50

Q 200-240 50/60 3 3+PE 56 60 60

X 200-240 50/60 1/3 2/3+PE 56 60 60

N 440-480 50/60 3 3+PE

Voltage

Cycle

Phase

Wire

Full Load

Amps

(US-market)

US NON-US US NON-US

AWG/mm

2

Heating Elements

kW Standard

Full Load

Amps

23 30 32

6x2 kW

Alternative Electric Heat Options

28 40 40

3x3 kW

+

3x2 kW

32 40 40

Recommended

Circuit Breaker

(US-market)

AWG/mm

2

10/6.0

8/10.0

6/16.0

N/A

8/10.0

6/16.0

8/10.0

P 380-415 50/60 3 3+N+PE 44

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 49

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 53

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE

5-08-52

Table 4

6x3 kW

3x3 kW

+

3x4 kW

6x4 kW

50 50

63

36 40 40

N/A N/A N/A N/A

41 50 50

N/A N/A N/A N/A

70 70

60 60

8/10.0

4/25.00

8/10.0

6/16.0

8/10.0

6/16.0

18

Washer-Extractors

Specifications and Dimensions - Model IHC035

Capacity (dry weight) Ratio (kg/l)

1:11

1:10

1:9

Cylinder

Cylinder diameter, in. (mm)

Cylinder depth, in. (mm)

Cylinder volume, ft.3 (l)

Cabinet

Overall height, in. (mm)

Overall width, in. (mm)

Overall depth, in. (mm)

Front Loading

Door opening size, in. (mm)

Height of door bottom above floor, in (mm)

Height of door center above floor, in (mm)

Speed

Was h

Distribution

Spin

G-factor

High Spin

Motor (3 phase), 4p, 1470 tr/min

Drain Valve, in. (mm)

Water Supply (hard, soft, warm water), in. (mm)

Direct Steam Heating

Steam inlet connection size, in. (mm)

Electrical

Electrical Heating (230/400 V)

Electrical Heating (400V)

Steam

Warm Water (without additional heating)

Warm Water (with additional heating)

Packing Dimensions (height X width X depth), in. (mm)

Weight

Net weight, lb. (kg)

Gross weight, lb. (kg)

33.07 lb. (15 kg)

36.38 lb. (16.5 kg)

40.34 lb. (18.3 kg)

25.59 (650)

19.69 (500)

5.83 (165)

47.32 (1202)

30.71 (780)

37.09 (942)

11.81 (300)

14.78 (376)

23.82 (605)

10-50 tr/min - RPM

85 tr/min - RPM

250-1000 tr/min - RPM

363

2.01 HP/1.5 kW

2 (51)

.75 (19)

.38 (10)

12 kW - 15 kW - 18 kW

21 kW - 24 kW

Not Applicable

51.57 X 33.46 X 42.52 (1310 X 850 X 1080)

789.25 (358)

855.39 (388)

19

5-08-52

Machine Dimensions - Model IHC035

CHM2217

47.32 in. (1202 mm)

46.3 in. (1176 mm)

7.87 in.

(200 mm)

8.66 in.

(220 mm)

25.51 in.

(648 mm)

1.34 in.

(34 mm)

14.78 in.

(376 mm)

30.71 in.

(780 mm)

1.44 in.

(36.5 mm)

3.23 in.

(82 mm)

30.12 in. (765 mm)

33.86 in. (860 mm)

36.06 in. (916 mm)

CHM2217N

CHM2216N

CHM2218N

13.05 in. (332 mm)

4.13 in. (105 mm)

10.49 in. (267 mm)

38.11 in.

(968 mm)

36.81 in.

(935 mm)

35.16 in.

(893 mm)

20.87 in.

(530 mm)

33.17 in.

(843 mm)

4.3 in. (109.2 mm)

2.36 in.

(60 mm)

2.76 in.

(70 mm)

1

2

9

7

5

3

6

8

10

4

2.6 in.

(66 mm)

1.34 in.

(34 mm)

2.6 in.

(66 mm)

1.44 in.

(36.5 mm)

3.47 in.

(88 mm)

7.93 in. (202 mm)

1.38 in.

(35 mm)

Washer-Extractors

CHM2216N

1 Ventilation Soap Dispenser 6 Electrical Connections 2 Warm Water Connections .75 in. 7 Drain Valve 3 Soft Water Connections .75 in. 8 Steam Connections 4 Ventilation Tub 9 Hard Water Connections .75 in. 5 Main Switch 10 Liquid Soap Connections

5-08-52

Figure 10

20

Washer-Extractors

CHM2219N

1.44 in.

(36.5 mm)

25.51 in.

(648 mm)

30.12 in.

(765 mm)

32.99 in.

(838 mm)

ø0.71 in.

(ø18 mm)

30.71 in.

(780 mm)

2.58 in.

(66 mm)

2.62 in.

(66 mm)

1.44 in.

(36.5 mm)

Mounting Bolt Hole Locations - Model IHC035

Figure 11

CHM2219N

21

5-08-52

Electrical Installation Requirements - Model IHC035

Only trained personnel should perform this procedure. Use caution while servicing machines with covers removed and power applied.

W700

WARNING

Washer-Extractors

Boiler Fed/Steam Heat Electric Heat

Recommended

Circuit Breaker

Code

N 440-480 50/60 3 3+PE 6 15 10 14/2.5

P 380-415 50/60 3 3+N+PE 18 20 20 12/4.0 44 50 50

Q 200-240 50/60 3 3+PE 18 20 20 12/4.0 63 70 70

X 200-240 50/60 1/3 2/3+PE 18 20 20 12/4.0 63 70 70

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 36 40 40

Q 200-240 50/60 3 3+PE 49 60 60

X 200-240 50/60 1/3 2/3+PE

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 40

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE

Voltage

Cycle

Phase

Wire

Full Load

Amps

(US-market)

US NON-US US NON-US

AWG/mm

2

Heating Elements

kW Standard

6x3 kW

Alternative Electric Heat Options

6x2 kW

3x3 kW

+

3x2 kW

Full Load

Amps

32 40 40

23 30 32

N/A N/A N/A N/A

28 40 40

50 50

56

60 60

Recommended

Circuit Breaker

(US-market)

AWG/mm

2

8/10.0

4/25.0

10/6.0

8/10.0

6/16.0

8/10.0

6/16.0

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 49

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE

N 440-480 50/60 3 3+PE

P 380-415 50/60 3 3+N+PE 53

Q 200-240 50/60 3 3+PE

X 200-240 50/60 1/3 2/3+PE

5-08-52

Table 5

3x3 kW

+

3x4 kW

6x4 kW

36 40 40

60 60

N/A N/A N/A N/A

41 50 50

60 60

N/A N/A N/A N/A

8/10.0

6/16.0

8/10.0

6/16.0

22

Washer-Extractors

Ensure that the machine is installed on a level floor of sufficient strength and that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

SW020

CAUTION

1

Installation - IHC Models

Surface

The machine must be securely fixed on a flat surface (metal base, concrete or solid ground). The anchoring is to be done on the 6 provided places in the holes on the corner of the base. (See Mounting Bolt Hole Locations). Refer to Figure 12.

CHM2102N

1 Mounting Bolt Holes

Figure 12

The machine must be placed entirely level. For easy maintenance it is recommended to keep a minimal distance of 23.62 in. (600 mm) between the wall and the back of the machine.

If several machines are placed next to each other, there should be a minimal distance of 1.18 in. (30 mm) between each machine.

IMPORTANT: The bolt pattern for the fixation of the IHC012 machine is located in the back panel of the cabinet. Put this panel on the floor and mark the holes.

23

CHM2102N

5-08-52