ION Audio IAS01 User Manual

Important Safety Instructions &

Warranty Information

Product Warranty

1. What is covered and for how long? All Products: ION Audio, LLC (“ION Audio”) warrants to the original purchaser

that this ION Audio product is free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized ION Audio dealer and continuing for ninety (90) days following the date of purchase. ION Audio warrants factory-refurbished merchandise to be free of material and operational defects for a period of ninety (90) days from the original date of retail sale. This refurbished merchandise warranty is not transferable.

2. What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser. This

Limited Warranty does not cover:

 Damage caused by improper installation or improper connection to any peripheral  Damage caused by an external electrical fault  Damage from use of parts not manufactured or sold by ION Audio  Product purchased from anyone other than an ION Audio authorized dealer  Modifications to product not approved in writing by ION Audio  Equipment that has the serial number removed or made illegible  Normal cosmetic and mechanical wear  Damage or loss during transit to an Authorized ION Audio Repair Center  Units that are purchased and/or located outside of the continental USA

3. What are ION Audio’s obligations? During the applicable warranty period, ION Audio will repair or replace, at ION

Audio’s sole option, without charge to the purchaser, any defective component part of the product. To obtain service under this Limited Warranty, purchaser must first contact ION Audio and obtain a return authorization number (“RA#”). Purchaser must then return the product to ION Audio in an adequate container for shipping, accompanied by purchaser’s sales receipt or comparable proof of sale showing the date of purchase, the serial number of the product, and the seller’s name and address. To obtain an RA# and assistance on where to return the product, contact ION Audio customer service at 401-658-3743 (U.S.A.). Upon receipt, ION Audio will repair or replace the defective products. ION Audio may, at ION Audio’s sole option, use rebuilt, reconditioned, or new parts or components when repairing any product or replace a product with a rebuilt, reconditioned, new or comparable product. Repaired products will be warranted for a period equal to the remainder of the original Limited Warranty on the original product or for 90 days, whichever is longer. All replaced parts, components, boards, and equipment become the property of ION Audio. If ION Audio determines that any product is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of such product.

4. What are the limits on ION Audio’s liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER

WITH ANY IMPLIED WARRANTIES COVERING ION AUDIO PRODUCTS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ION AUDIO SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER’S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY ION AUDIO PRODUCT, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO ION AUDIO’S OWN NEGLIGENCE, EVEN IF ION AUDIO OR THEIR AGENTS HAVE BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR ION AUDIO PRODUCTS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER’S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS. This Limited Warranty allocates risk of product failure between purchaser and ION Audio, and ION Audio’s product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of ION Audio are not authorized to make modifications to this Limited Warranty, or make additional warranties binding on ION Audio. Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by ION Audio and should not be relied upon.

5. How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.

This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.

Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom you purchased the unit. Retain this information and your original purchase receipt for your records. Go to our web site

ionaudio.com to register your product with us.

Model:__________________________________________________ Purchased From: ______________________________________

Serial Number: __________________________________________ Date of Purchase: _____________________________________

(purchases made in U.S.A.)

Product Warranty

(purchases not made in U.S.A.)

1. ION Audio, LLC (“ION Audio”) warrants to the original purchaser that ION Audio products are free from

defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized ION Audio dealer and continuing for the following period of time after that date for (1) Year.

2. This Limited Warranty is conditioned upon proper use of the product by the purchaser.

This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification of any part of the product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally exposed parts that are scratched or damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment, or service of the products.

3. During the applicable warranty period, ION Audio will repair or replace, at ION Audio’s sole discretion,

without charge to the purchaser, any defective component part of the product. ION Audio may, at ION Audio’s sole discretion, use rebuilt, reconditioned, or new parts or components when repairing any product or replace a product with a rebuilt, reconditioned, new or comparable product.

4. THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED

WARRANTIES COVERING ION AUDIO PRODUCTS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ION AUDIO SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER’S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY ION AUDIO PRODUCT, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO ION AUDIO’S OWN NEGLIGENCE, EVEN IF ION AUDIO OR ITS AGENTS HAVE BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR ION AUDIO’S PRODUCTS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER’S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.

This Limited Warranty allocates risk of product failure between purchaser and ION Audio, and ION Audio’s product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of ION Audio are not authorized to make modifications to this Limited Warranty, or make additional warranties binding on ION Audio. Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by ION Audio and should not be relied upon. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary under local laws.

Model:____________________________________ Purchased From: ____________________________________

Serial Number: ____________________________ Date of Purchase: __________________________________

Return Information

A Return Authorization number must be obtained from your local ION Audio Representative. For your

•

representative go to ionaudio.com. A copy of the original sales receipt must also be included for the equipment to be repaired under

•

warranty.

•

The faulty equipment must be packed in its original packaging.

•

One additional outer layer of packaging must be included to ensure product safety. Failures to do so may inadequately protect the equipment in transit and, therefore, jeopardize the customer’s warranty.

•

ION Audio will not accept C.O.D. shipments and no call tags will be issued for merchandise return.

•

ION Audio will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be submitted in writing with merchandise returned.

•

The defective ION Audio equipment should be sent, freight prepaid with Return Authorization number clearly printed on the outer packaging and original sales receipt enclosed to your local service center

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized plug or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachment/accessories specified by the manufacturer.

12. Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus (if applicable). When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Power Sources: This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit.

Water and Moisture: This product should be kept away from direct contact with liquids. The apparatus

16. shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution (if applicable): Danger of explosion if battery is incorrectly replaced. Replace only with the

17.

same or equivalent type. Batteries (a battery pack or an installed battery) shall not be exposed to excessive heat such as sunshine, fire, etc. (This applies only if your product uses a battery.)

Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device

18.

shall remain readily operable.

If applicable: This symbol means the equipment is a Class II or double-insulated electrical appliance.

19.

It has been designed in such a way that it does not require a safety connection to electrical earth. Do not install this equipment in a confined or “boxed-in” space such as a bookcase or similar unit, and

20.

maintain good ventilation conditions. If your product has ventilation openings, the ventilation should not

be impeded by covering them with items such as newspaper, tablecloths, curtains, etc.

When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable tie). Be

21. careful not to damage the power cord. Before using it again, make sure the power cord has not been

damaged. If the power cord has been damaged at all, bring the unit and cord to a qualified service technician for repair or replacement as specified by the manufacturer.

Warning: Excessive sound pressure (high volumes) from headphones can cause hearing loss.

22. Warning: Please refer to any important information (e.g., electrical, safety, etc.) printed on the exterior

23. bottom enclosure or rear panel before installing or operating the product.

24.

No naked flame sources, such as lighted candles, should be placed on the apparatus

25.

Attention should be drawn to environmental aspects of battery disposal. Use of the apparatus in moderate climates.

26.

The ventilation should not be impeded by covering the ventilation openings with items,

27.

such as newspapers, table-cloths, curtains, etc.

Minimum distances around the apparatus for sufficient ventilation

28.

Service Instructions

• Disconnect power cord before servicing.

• Replace critical components only with factory parts or recommended equivalents.

• For AC line powered units: Before returning repaired unit to user, use an ohmmeter to measure from both

AC plug blades to all exposed metal parts. The resistance should be more than 2,000,000 ohms.

Safety Notices

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

INSTRUCTIONS: The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this appliance.

WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.

CAUTION (for U.S.A. & CANADIAN models only): TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTICE CONCERNING LASER PRODUCTS: DANGER: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOSURE TO BEAM. USE OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

NOTICE CONCERNING FCC REGULATIONS: You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (a) reorient or relocate the receiving antenna; (b) move this unit; (c) increase the separation between the equipment and receiver; (d) donnect the equipment into an outlet on a circuit different from that to which the receiver is connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where appropriate; (f) consult the dealer or an experienced radio/television technician for help.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause

2. Any Changes or modifications not expressly approved by the party responsible for compliance

user's authority to operate the equipment.

conditions:

undesired operation.

could void the

2. any Changes or modifications not expressly approved by the party responsi ble for compliance

could void the user's authorit

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

pursuant to Part 15 of the FCC Rules.

in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and

with the instructions,

However, there is no guarantee that interference will not occur in a particular installation. If this interference to radio

the user is encouraged to try to correct the

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio/TV technician for help.

or television reception, which can be

y to operate the equipment.

These limits are designed to provide reasonable

to radio communications.may cause harmful interference

determined by turning the equipment off and on,

interference by one or more of the following measures:

device,

protection against harmful interference

used in accordance

equipment does cause harmful

connected.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body

For Canadian models:

• This device complies with Industry Canada licence-exempt RSSs. Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

• This unit does not exceed the Class B limits for radio noise emission from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

•

L'exploitation est autorisée aux deux conditions

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accept

même si le brouillage est susceptible

In an environment with radio frequency interference, the unit may malfunction and resume normal operation after removal of the interference. For best audio quality, avoid using this device in a high RF-radiated environment. For 240-volt use in U.K., use NEMA-style 240-volt plug. For other countries use proper plug for local outlet.

Double-Insulated: When servicing use only identical replacement parts.

ESD/EFT Warning: This unit may contain a microcomputer for signal processing and control functions. In

very rare situations, severe interference, noise from an external source, or static electricity may cause it to lock up. In the unlikely event that this should happen, turn off the unit, wait at least five seconds, and then turn it back on again.

suivantes :

er tout brouillage radioélectrique subi,

d'en compromettre le fonctionnement."

appareils radio exempts de licence.

Disposing of General Purpose & Alkaline Batteries:

Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. (California law requires this warning to be given to customers in the State of California.)

Correct Disposal of This Product: This marking indicates that this product should not be disposed with

other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

•

Alkaline batteries can be safely disposed of with normal household waste. Never dispose of batteries in fire because they could explode. Alkaline batteries are composed primarily of common metals—steel, zinc, and manganese—and do not pose a

•

health or environmental risk during normal use or disposal. It is important not to dispose of large amounts of alkaline batteries in a group. Used batteries are often not

•

completely “dead.” Grouping used batteries together can bring these “live” batteries into contact with one another, creating safety risks. Proven cost-effective and environmentally safe recycling processes are not yet universally available for alkaline

•

batteries. Some communities offer recycling or collection of alkaline batteries. Contact your local government for disposal practices in your area.

World Headquarters:

Phone:

Fax:

ION Audio 200 Scenic View Drive Cumberland, RI 02864 USA

401.658.3743 (USA)

401.658.3640 (USA)

ionaudio.com

Manual Version 15.2

iAS01

Quickstart Guide

Guía de inicio rápido

Guide d'utilisation rapide

Guida rapida

Schnellstart-Anleitung

Snelstartgids

Appendix

English ( 3 – 9 )

Español ( 10 – 16 )

Français ( 17 – 23 )

Italiano ( 24 – 30 )

Deutsch ( 31 – 37 )

Nederlands ( 38 – 44 )

English ( 46 )

Remote

Note: The remote requires 1 AAA battery (included) to function.

• Power Button: Press this button to power on the unit or to put it into standby mode.

• Src: Press this button to select the playback source: CD, USB, Tuner, Aux In, Line In, and Bluetooth.

• Eject: Press this button to eject the CD in the CD Tray.

• Fold-: Press this button to return to the previous folder.

• Fold+: Press this button to move to the next folder.

• Previous / Rewind: Press this button to go to the previous track. Press

and hold this button to rewind. In FM Tuner mode, press and release this button to move to the previous

preset station. Press and hold this button to travel backward through the FM band to find the next strongest station.

• Play / Pause: Press this button to play or pause the playback. In Bluetooth mode, press and hold this button for 5 seconds to

disconnect a Bluetooth connection.

• Next / Fast-Forward: Press this button to go to the next track. Press and hold this button to fast-forward.

In FM Tuner mode, press this button to move to the previous preset station. Press and hold this button to travel forward through the FM band to find the next strongest station.

• Tun- / 10-: In FM Tuner mode, press this button to skip backward through the radio channels.

In CD or USB modes, press this button to move backward 10 tracks.

• Stop / Auto: Press this button to stop playback. In FM Tuner mode, press and hold this button to automatically scan through the FM band.

• Tun+ / 10+: In FM Tuner mode, press this button to skip forward through the radio channels. In CD or USB modes, press this button to move forward 10 tracks.

• Time / Info: Press this button to toggle the Display to show time elapsed, time remaing, or ID3 tag data.

Note: ID3 tag data may not be available with all file formats.

• Mem: In FM Tuner mode, you can use button to save a station as a favorite preset. See

Operation > Using the Radio for more information.

• Prg: In CD or USB mode, press this button once to access Program mode and create a custom playback order. Use the Previous and Next buttons to navigate tracks, and press Program again to confirm your selection. Once finished, press Play/Pause to resume playback.

• Mute: Silences music playback.

• Rep: Press this button to switch between Repeat Playback modes: Off, Repeat One, or Repeat

All.

• Rnd: Press this button to turn on Random Playback mode.

• Vol -: Decreases the source volume.

• Vol +: Increases the source volume.

• EQ: Press this button to switch equalizer settings.

• Tone: Press this button to create a custom EQ setting. Use the Vol - and Vol + buttons to adjust

the Bass and Treble settings. This setting will be saved as the “Custom” EQ setting.

SRC

FOLD FOLD

AUTO

TUN

TIME

MEM

INFO

MUTE REP

TUN

PRG

RAND

Operation

Selecting the Media Playback Mode

To select what kind of media you want to play:

• Press the Source button on the unit.

• Press the Src button on the remote control.

Bluetooth Pairing

To pair your Bluetooth device:

1. If the unit is off, press the Power button to power it on.

2. Make sure your desired Bluetooth device has its Bluetooth connectivity on and is within range.

3. Press the Source button on the unit or the remote to enter Bluetooth mode.

4. Navigate to the Bluetooth setup screen on your device, find ION iAS01 and connect. Note: Some older Bluetooth devices may require you to enter a PIN. If this is the case,

enter 0000 as the PIN.

5. On your Bluetooth device, start playing audio.

To unpair your Bluetooth device:

• Enter your Bluetooth device’s Bluetooth settings menu, and disconnect from ION iAS01.

• Press and hold the Play/Pause button on the remote control to unpair your device.

Playing Audio CDs

To play audio CDs:

1. If the unit is off, press the Power button to power it on. Important: Do not insert a CD when the power is off. Doing so may damage the unit.

2. Insert a CD into the CD Tray.

3. Select CD as the media type (described in Selecting the Media Playback Mode).

4. To start playback, press the Play/Pause button on the unit or remote control.

Playing Audio Files

To play audio files on a USB device:

1. If the unit is off, press the Power button to power it on.

2. Connect your USB device (mass storage class) to the USB Port.

3. Select USB as the media type (described in Selecting the Media Playback Mode).

4. Select an audio file using the Previous and Next buttons. If your USB device contains folders, you can navigate between folders using the Fold -/+ buttons. The file will play automatically.

Playing Audio from an External Device

To play audio from an external device (e.g., smartphone, computer, turntable, etc.):

1. If the unit is off, press the Power button to power it on.

2. Connect the 1/8” (3.5 mm) headphone output or RCA stereo output of your external device to the Aux In or Line In input on the unit, respectively.

Important: The Aux In and Line In inputs are line-level. Your audio sources must be linelevel (no phono-level turntables).

3. Select Aux In or Line In as the media type by pressing the Source button on the unit or the remote control.

4. To start playback, press Play on your external device.

Using the Radio

1. Attach the FM Antenna Cable to the Antenna input on the back of the unit.

2. If the unit is off, press the Power button to power it on.

3. Select Tuner as the source (described in Selecting the Media Playback Mode).

4. Press the Tun -/+ buttons on the remote control to travel through the FM band. You can also press and hold the Previous and Next buttons to jump backward or forward through the FM band to the next strongest station.

5. Press and release the Previous and Next buttons to change FM presets.

To add a station as a preset:

1. Use the Tun -/+ buttons to select the desired radio station.

2. Press the Mem button.

3. Use the Previous and Next buttons to select a preset number.

4. Press the Mem button again to save the station to that preset.

Troubleshooting

If you encounter a problem, do the following:

• Make sure all cables, devices, antennae, and/or media are properly and securely connected.

• Make sure you are using the unit as described in this Quickstart Guide.

• Make sure your other devices or media are working properly.

• If you believe the unit is not working properly, check the following table for your problem

and solution.

Problem Solution Please see:

Power does not turn on.

The unit does not produce any sound, or the sound is distorted.

The remote control does not function.

Audio from my Bluetooth device does not play.

No Disc appears even when a CD is inserted.

Make sure the unit is connected to a power outlet.

Make sure all cable, device, or media connections are secure and correct.

Make sure none of the cables are damaged.

Make sure the Mute function is not engaged.

Adjust the Volume control.

Make sure there are batteries in the remote control.

Replace the batteries with new ones. Make sure the remote control is pointed at

the unit. Make sure you are within range of the unit.

Make sure you have properly paired your Bluetooth device.

Improve the Bluetooth signal reception by moving your Bluetooth device closer to the unit. Also, remove obstacles (walls, furniture, etc.) so there is a clear line of sight between your Bluetooth device and the unit.

Press the Eject Button to eject the CD and insert it again.

Quick Setup > Connection Diagram

Operation > Bluetooth Pairing

Operation > Playing Audio CDs

Playback does not start even after pressing the Play button.

Make sure the unit is connected to a power outlet and that it is powered on.

Clean the CD with a dry cloth or commercial CD cleaner.

Insert a different CD.

Operation > Playing Audio CDs

Problem Solution Please see:

No Songs appears

even when a USB device is inserted.

Files on a USB device do not appear.

Files on a USB device cannot play.

Disconnect and reconnect the USB device to make sure it is securely inserted.

Make sure the USB device is of a mass storage class or compatible with MTP.

Make sure the USB device is formatted using a FAT16 or FAT32 file system.

Do not use a USB hub or USB extension cable.

Not all USB devices are guaranteed to work; some may not be recognized.

Make sure the files are of a supported file format. Only mp3 and wma files are supported on USB. Files that are not supported by this unit will not appear.

Make sure the USB device uses a folder structure that the unit supports: up to 999 folders (up to 8 folder levels, including the root) and up to 999 files.

If your USB device is partitioned, make sure the files are in the first partition. The unit will not show other partitions.

Make sure the files are of a supported file format. Only mp3 and wma files are supported on USB. Files that are not supported by this unit will not appear.

Make sure the files are not copyrightprotected. The unit cannot play copyrightprotected files.

Operation > Playing Audio Files

The source sound is too low, or the sound has noise.

Using the radio produces noise.

Make sure the volume is properly set.

The Aux In and Line In inputs are linelevel. Your audio sources must be linelevel (no phono-level turntables).

Make sure the antenna is properly connected.

Change the position or orientation of the antenna.

Use an outdoor FM antenna (not included).

Move the antenna away from other cables.

Operation > Playing Audio From an External Device

Operation > Using the Radio

+ 39 hidden pages