ION Audio AIRLP User Manual
™
Air LP
Quickstart Guide English ( 3 – 7 )
Guía de inicio rápido Español ( 8 – 12 )
Guide d'utilisation rapide Français ( 13 – 17 )
Guida rapida Italiano ( 18 – 22 )
Schnellstart-Anleitung Deutsch ( 23 – 27 )
Snelstartgids Nederlands ( 28 – 31 )
Air LP Vinyl Player
Quickstart Guide (English)
Introduction
Box Contents
Make sure that the items listed below are included in the box:
• Air LP™
• Power adapter
• Dust Cover
• USB cable
• RCA Cable
• 1/8” (3.5 mm) Aux Cable
• 45 RPM Adapter
• Felt Slipmat
• Software CD
• Quickstart Guide
• Safety & Warranty Manual
Support
For the latest information about this product (system requirements, compatibility information,
etc.) and product registration, visit ionaudio.com.
Connection Diagram
Items not listed under the Box Contents are sold separately.
Features
1. Platter – Place your record here.
2. 45 RPM Adapter Holder – Holds the included
45 RPM adapter. When not using the adapter,
please place it in this holder.
3. Tonearm – The fixed tonearm can be raised
and lowered by hand, or by pressing the raise /
lower lever.
4. Arm Clip – This specially designed arm clip
secures the tonearm while at rest or when not
in use. The arm clip has been designed to
remain in the up position while unlocked.
Bluetooth Speaker
2
3
1
5
6
7
4
11
9
8
10
2
14
13
16
15
5. Raise / Lower Lever – Raises and
lowers the tonearm.
6. 33 / 45 / 78 Switch – This switch
controls the RPM of the turntable
platter.
Note: For best results when playing 78 RPM vinyl records, use a 78 stylus (sold
separately). Only use a 78 stylus with 78 RPM vinyl records. Purchase the iCT06rs 78
stylus at ionaudio.com/ict06rs.
7. Autostop switch – This switch turns autostop on or off. When autostop is on, the platter
will start spinning when the tonearm is placed over the record and stop spinning when the
record has reached the end. (When autostop is off, the platter will always spin regardless
of the position of the tonearm.)
Note: If your vinyl record stops before it reaches the end of the music, turn Autostop to
the off position for this particular record. This is generally recommended for 45 RPM
records.
8. Headphone Jack – Connect headphones (sold separately) to listen to your vinyl
playback.
9. Bluetooth Button – Press this button to start
Bluetooth pairing. If after 5 minutes no
Bluetooth speaker can be found to pair with, the
Bluetooth transmitter will become inactive and
the LED will turn off. If currently connected,
press this to disconnect from a currently
connected bluetooth device.
10. Bluetooth LED – This LED blinks when pairing
with a Bluetooth device. Once fully paired, the
LED will remain solid. The LED will be off when
bluetooth is inactive, and when the Air LP is
turned off.
11. Volume – Adjust this to control the headphone
level.
12. RCA Output* – The audio from a playing vinyl record is sent to this line-level coaxial
audio output. This must not be connected to phono level devices.
13. USB Audio Output – Use the included USB cable to connect your turntable to your
computer. The USB connection will send audio from the turntable to your computer.
Please see the Using Air LP With Your Computer section of this manual for information.
14. Power Cable Input – Use the included adapter to connect to wall power.
15. Power Button – Press this button to turn Air LP on/off. Air LP Turntable will re-connect to
your last used Bluetooth Speaker when powering on, if it is in range.
16. Aux Input – Connect a CD player, digital media player, or other audio source to this 1/8”
stereo auxiliary input. The audio from the Aux Input is also transmitted over a Bluetooth
connection.
IMPORTANT: Place the included felt
slipmat on the platter; then place your
record on the felt slipmat to carefully hold
your records.
IMPORTANT: Remove the plastic
cartridge cover (needle cover) before
operating the turntable.
*WARNING: The RCA outputs are LINE
level. Please only connect these to LINE
level inputs. You may damage your
receiver if you plug in a LINE level device
into a PHONO level input.
12
3
Loading...