Page 1
Page 2
Outdoor DMX Flood Bar, 44*Tri-3W RGB
User Manual
Our Outdoor LED Flood bar offers many possibilities to achieve the effects which you want. It is for DJs, bands,
nightclubs and other performers who want a complete LED wash light system. Please read the manual before
operation.
A. SPECIFICATION
1. Power input: 110~240VAC 50/60Hz
2. Power consumption: 152W
3. Fuse choosing: 1.5A/250V@240V, 3A/125V@110V
4. LED: 44pcs tri-3w
5. Beam angle: 40 degree
6. Working Temperature: -10~40℃
7. DMX channel: 5CH, 8CH, 9CH
8. DMX connection type: 3-pin
9. IP rate: IP65
10. Working mode：DMX mode, master/slave mode, built-in programs, auto running, static color
11. Power out connect the fixture quantity: 9pcs@240V, 4pcs@110V
12. The buttons can be locked
13. Weight: 11.3kg
14. Size: 1027*160*212.7mm
B. OPERATION
There are many kinds of effects for this item, it is easy to operate, and there are six kinds of working mode as
below:
·built-in programs
·auto running
·DMX mode
·master/slave mode
·single fixture controlled static color mode
·whole fixture static color mode
1. Built-in Programs Mode
1. Press the “MODE” to enter into the manual choosing menu “Pr.xx”.
2. Press the “UP “or “DOWN” to choose the program from ~ .
Page 3
3. When the LED display shows ~ , first time to press the “SETUP”, it will shows the “SP.XX”, then
CHANNEL
VALUE
FUNCTION
CH1
0-255
Master dimmer
CH2
0-255
Red
CH3
0-255
Green
CH4
0-255
Blue
CH5
0-255
Strobe
CHANNEL
VALUE
FUNCTION
CH1
0-255
Master dimmer
CH2
0-255
Red 1
CH3
0-255
Green 1
CH4
0-255
Blue 1
CH5
0-255
Red 2
CH6
0-255
Green 2
CH7
0-255
Blue 2
CH8
0-255
Strobe
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
0-255
0-255
0-255
0-255 0 0
NO
0-255
0-127
setup the program running speed ～ (SP100). through the “UP” or “DOWN”; second time to press
the “SETUP”, it will shows the “FSxx”, then setup the speed of the strobe ～ through the “UP” or
“DOWN”.
2. Auto Running Mode
Press the “MODE” to enter into the auto running working mode “AUTO”, the fixture will perform the 9 kinds of
working mode from Pr.01~Pr.09, the user can setup the running speed, strobe speed under the program of
Pr.01~Pr.09, the finished effects would be perform in order under the auto running working mode.
3. DMX Mode
1. Press the “MODE”, enter the DMX working mode menu “d.×××”.
2. Press the “UP” or “DOWN” to setup the DMX address value ～ .
3. Press the “SETUP”, enter the DMX working mode menu X-ch.
4. Press the “UP” or “DOWN” to set up the DMX working mode, there are three kinds of working mode as ,
, .
DMX working mode 1：
DMX working mode 2:
DMX working mode 3: （9 channels）
Page 4
MASTER
DIMMER
RED
GREEN
BLUE
USE
STROBE
Function
1
NO
USE
NO
USE
NO
USE
1-255
TABLE
1
NO
USE
1-255
TABLE
2
0-255
SPEED
0-255
RED 1
0-255
GREEN
1
0-255
BLUE 1
0-255
RED 2
0-255
GREEN
2
0-255
BLUE 2
128-255
Function
2
TABLE 1
CH5
DMX
value
FUNCTIO
N
1-22
red
23-45
green
46-68
blue
69-91
blueness
92-114
yellow
115-137
orange
138-160
pink
161-183
purple
184-206
Dark blue
207-229
Pale green
230-252
white
253-255
Warm
white
TABLE 2
CH6
DMX
value
FUNCTIO
N
1-15
red
16-31
green
32-47
blue
48-63
yellow
64-79
blueness
80-95
purple
96-111
white
112-127
Pr01
128-143
Pr02
144-159
Pr03
160-175
Pr04
176-191
Pr05
192-207
Pr06
208-223
Pr07
224-239
Pr08
240-255
Pr09
D. Master/slave Mode
Press the “MODE”, enter the master/slave mode “SLAV”.
E. Single fixture controlled static color mode
1) Press the “MODE”, enter the single fixture controlled static color mode“COL1”
2) Press the “SETUP”, it will show“1.xxx”（first fixture: red）, “2.xxx”(firs fixture: green), “3.xxx”(first fixture:
blue), “4.xxx”(second fixture: red), “5.xxx”(second fixture: green), “6.xxx”(second fixture: blue)
3) Press the “UP “or “DOWN” to adjust the brightness of the static color.\
Page 5
F. Whole fixture static color
1) Press the “MODE” enter the whole fixture static color mode“COL2”
2) Press the “SETUP”, it will show “r.xxx”（red）, “g.xxx”(green), “b.xxx”(blue)
3) Press the “UP” or “DOWN” to adjust the brightness of the static color.
NOTE:
1. If there is no press within 20 seconds, the LED display will turn off. At the same time, the button would be
locked to avoid any disoperation from irrelevant personnel. Then if press any button, the LED Display will show
“Lock”, it means the button has been locked. After you press the “MODE”+ “DOWN” two buttons more than 1
second, The LED display will recover the display, then every button will recover its function.
2. This fixture has the function of self-protection from the high temperature, when the fixture under the whole
lighting for a long time, the fixture would adjust the power consumption by itself according to the heat dissipation.
If the user needs the fixture working under the whole power consumption, please keep unobstructed for the heat
dissipation.
3. When the fixture get power, it will show the version, such as V1.0, it will keeps about 2 seconds, then perform
the working mode of the user’s setting.
Page 6
ООО «ИНВАСК»
Адрес: 143406, Московская область, Красногорск, ул. Ленина, дом 3-Б
Тел. (495) 565-0161 (многоканальный)
Факс (495) 565-0161, доб. 105
http://www.invask.ru e-mail: invask@invask.ru
Сервис-центр «ИНВАСК»
Адрес: 143400, Московская область, Красногорск, Коммунальный квартал,
дом. 20
Тел. (495) 563-8420, (495) 564-5228
e-mail: service@invask.ru
Loading...