Page 1
Page 2
Outdoor LED Flood light, 24*Tri-9W
Our DMX LED Flood Panel offers many possibilities to achieve the effects which you want. It is for DJs, bands,
nightclubs and other performers who want a complete LED wash light system. Please read the manual before
operation.
A. SPECIFICATION
1. Voltage: AC 100V/240V, 50Hz/60Hz
2. Power consumption: 200W
3. LEDs: 24*Tri-9W
4. Beam angle: 45 degree
5. IP rate: IP65
6. Control feature: auto running, slave mode, DMX Mode, built-in program, and static color
7. DMX channels: 1,3,4,6 CH
8. Operation mode: LED display for easier operation.
9. Size: 58*28*34cm
10. Weight: 19kg
B. OPERATION
Built-in programs—running one of 10 built-in programs
Auto run—running built-in programs one after another in continuous loop
DMX mode—controlled by DMX controller
Slave mode—the projectors in this mode will be synchronously run with the projectors in master mode.
1. Built-in Programs Mode
1) Press “MODE”, enter the program mode “Pr.××”
2) Press “UP” or “DOWN” button select the program from ~ .
3) Press “SETUP” to choose the seven static colors When it shows . Press “UP” or “DOWN” button, you can
select the seven static color (1.-r; 2.-rg; 3.-g; 4.-gb; 5.-b; 6.-rb; 7.rgb), when it shows “7.rgb”, press “SETUP”
button, you can through the “UP” or “DOWN” button to adjust the brightness for R,G,B color. Press again the
“SETUP” button can setup the flash of the selected color “FSxx”, through the “UP” or “DOWN” button can adjust
Page 3
the speed of the flash from ~ .
CH1
NO.
DMX value
FUNCTION
1 0 No use
2
1-22
Red
3
23-45
Green
4
46-68
Blue
5
69-91
Cyan
6
92-114
Yellow
7
115-137
Orange
8
138-160
Pink
9
161-183
Purple
10
184-206
Dark blue
11
207-229
Light green
12
230-252
White
13
253-255
Warm white
CHANNEL
VALUE
FUNCTION
CH1
0-255
Red
CH2
0-255
Green
CH3
0-255
Blue
CHANNEL
VALUE
FUNCTION
CH1
0-255
M Master dimmer
CH2
0-255
Red
CH3
0-255
Green
CH4
0-255
Blue
2. Auto Running Mode
1) Press “MODE” button, enter the auto program mode “AUTO”. It will auto run 9 built-in programs from ~
.
User can set up the running speed and flash speed for ~ under built-in programs mode, then the
setup program and effect will be run in order under auto run mode.
3. DMX Mode
1) Press “MODE” button, enter DMX mode “d.×××”.
2) Press “UP” or “DOWN” button, setup DMX address value ~ .
3) Press “SETUP” button, enter setup DMX mode X-ch.
4) Press “UP” or “DOWN” button, setup DMX mode: , , ,
DMX mode 1:
DMX mode 2:
DMX mode 3:
Page 4
CHANNEL
VALUE
FUNCTION
CH1
0-255
Master dimmer
CH2
Red dimmer
0-255
Red dimmer 0-255
Select different static color(it
is available when 6ch is 0-25)
0-8
R(255)
9-17
R(255) G(50)
18-26
R(255) G(150)
27-35
R(255) G(255)
36-44
R(200) G(255)
45-53
R(100) G(255)
54-62
R(40) G(255)
63-71
G(255)
72-80
G(255) B(50)
81-89
G(255) B(150)
90-98
G(255) B(255)
99-107
G(150) B(255)
108-116
G(50) B(255)
117-125
B(255)
126-134
R(50) B(255)
135-143
R(150) B(250)
144-152
R(255) B(255)
153-161
R(220) B(50)
162-170
R(150) G(50) B(100)
171-179
R(50) G(180) B(220)
180-188
R(50) G(220) B(100)
189-197
R(150) G(220)
198-206
R(150) B(220)
207-215
G(180) B(220)
216-224
G(220) B(50)
225-233
R(220) G(100) B(50)
234-242
R(220) G(200) B(100)
243-251
R(255) G(200) B(150)
252-255
R(255) G(255) B(255)
Speed adjustable（to control the
grogram speed which selected by
CH6（26-255））
0-255
0—255 slow—fast
CH3
0-255
Green dimmer 0-255
CH4
0-255
Blue dimmer 0-255
CH5
0-9
NO FUNCTION
DMX mode 4: （6 channels）
Page 5
10-255
STROBE （slow—fast）
CH6
0-25
Can be select 29 kinds static
color through 2ch
26-51
Pr02（seven color gradual
change ）
52-77
Pr03（three color gradual
change）
78-103
Pr04（seven color jumping
change）
104-129
Pr05（three color jumping
change）
130-155
Pr06（fantastic 1）
156-181
Pr07（fantastic 2）
182-207
Pr08（red color gradual change）
208-233
Pr09（green color gradual
change）
234-255
Pr10（blue color gradual change）
4. Master/slave Mode
Press “MODE” button enter into slave mode “SLAV”.
NOTE:
1. If 4 buttons without any press within 20 seconds, the LED display will be close the show. If any buttons will be
pressed, the LED display will be resuming the original condition. Then all the buttons will be work in normal.
2. It is of thermal self-protection. If it is full on last a long time, the system will adjust the power consumption in
order to reduce the heat. Please make sure around is well ventilated when the unit is full on.
3. It will show the version, such as V1.0, when turn on the system. Two seconds later, it will run normally with the
Page 6
setup mode.
Loading...