Page 1
Page 2
1
Outdoor LED Flood Light, 24*4-in-1 8W Manual
Our Outdoor LED Flood Light offers many possibilities to achieve very nice laser effects which you want. It is
specially designed for the stages, disco, night clubs etc. Please read the manual before operation.
A. SPECIFICATION
1. Voltage: AC 100V/240V, 50Hz/60Hz
2. Power consumption: 190W
3. LED: 24*4-in-1 8W
4. Control feature: DMX mode, m/s, auto running, built-in programs, static color
5. DMX channels: 1, 4, 5, 7 CH
6. Operation mode: LED display
7. Fuse: 2A/250V @240V, 3A/125V @110V
8. Support power in and power out, power linking: 10pcs@240V, 5pcs@110V
9. Beam angle: 45degree
10. Projection distance: more than 50M (RGB)
B. OPERATION
This product has many effect programs with simplicity of operation. There are four working modes:
Built-in Program
Auto Running
DMX Mode
M/S Mode·
1. Built-in Programs
1) Press “MODE” button to select the program “Pr. ××”.
2) Press “UP” or “DOWN” button to select the effect programs from ~ .
Page 3
2
CH1
NO. DMX
value
FUNCTION
1 0 No use
2
1-22
Red
3
23-45
Green
4
46-68
Blue
5
69-91
Cyan
6
92-114
Yellow
7
115-137
Orange
8
138-160
Pink
9
161-183
Purple
10
184-206
Dark blue
11
207-229
Light green
12
230-252
White
13
253-255
Warm white
CHANNEL
VALUE
FUNCTION
CH1
0-255
RED
CH2
0-255
GREEN
3) Press “SETUP” button to edit the static color when the display board shows , then press “UP” or “DOWN”
button to select the fourteen built-in static colors (1.-r; 2.-rg; 3.-g; 4.-gb; 5.-b; 6.-rb; 7.rgb; 8.-w; 9.-FL; 10.rw;
11.gw; 12.bw; 13.yw; 14.uw), Press “SETUP” button to adjust the brightness of red, green, blue and white through
“UP” or “DOWN” button when it shows 9.-FL. Press “SETUP” button again could set up the strobe “FSxx” for the
color that is chose, and press “UP” or “DOWN” button to adjust the strobe speed from ~ .
4) When the display board shows ~ , the first time to press “SETUP” button, it will show “SP.XX”, the
program running speed could be adjusted through UP or DOWN button from ~ (SP100).The second time
to press SETUP button, it will show “FSxx”, the strobe speed could be adjusted through “UP” or “DOWN” button
from ~ .
2. Auto Running Mode
Press “MODE” button to enter into Auto Running mode “ ”, the fixture will run the built-in program from
~ automatically. The running and strobe speed of each program from ~ could be set up, and
the preset effect will run sequentially under the mode of auto running.
3. DMX Mode
1) Press “MODE” button to enter into the DMX Mode “d. ×××”.
2) Press “UP” or “DOWN” button to set the DMX address ~ .
3) Press “SETUP” button to enter into DMX working mode menu X-ch.
4) Press “UP” or “DOWN” button to set the DMX working mode, there are four modes: , , ,
DMX Mode 1:
DMX Mode 2:
Page 4
3
CH3
0-255
BLUE
CH4
0-255
COOL WHITE
CHANNEL
VALUE
FUNCTION
CH1
0-255
MASTER DIMMER
CH2
0-255
RED
CH3
0-255
GREEN
CH4
0-255
BLUE
CH5
0-255
COOL WHITE
CHANNEL
VALUE
FUNCTION
CH1
0-255
Master dimming
CH2
Red Dimming
0-255
Red dimming 0-255
43 kinds of static
color selectable(it
is in valid while
7CH is 0~22)
Every 5
transform a
monochromatic
43 kinds of static colors
Speed Adjustment
(control the
program speed of
CH7 {23-255})
0-255
0—255 slow —fast
CH3
0-255
Green dimming 0-255
CH4
0-255
Blue dimming 0-255
CH5
0-255
Cool white dimming 0-255
CH6
0-9
NO FUNCTION
10-255
STROBE (slow —fast )
CH7
0-22
43 static colors could be selected through
2CH
23-45
Pr02(gradual changing 1)
46-68
Pr03(gradual changing 2)
69-91
Pr04(flickering 1)
92-114
Pr05(flickering 2)
115-137
Pr06(illusion 1)
138-160
Pr07(illusion 2)
161-183
Pr08(red gradual changing)
184-206
Pr09(green gradual changing)
207-229
Pr10(blue gradual changing)
230-255
Pr11(cool white gradual changing)
DMX Mode 3:
DMX Mode 4: (7channels)
Page 5
4
4. Mater/ slave Mode
Press the “MODE” button, enter into M/S mode “SLAV”.
NOTE:
1. If no touch be pressed within 20 seconds, the display board will be turned off, and at the same time lock the keys,
prevent irrelevant personnel of mirror operation. If presses any button at this time, the LED display will show
“Lock”, it means the key has been locked. Need to long press the “MODE”+ “DOWN” button one second or more
unlock, the LED display will recover the shows before turn out. And then all the buttons will regain their own
functions.
2. This fixture has the self-protection function against the excess temperature. The system will adjust the service
power automatically according to the heat dissipation of the fixture while the user makes all the LEDs worked for a
long time, please keep the surroundings ventilated under this working condition.
3. The display board will show the system’s version after the fixture is turned on, such as V1.0, after 2 seconds it
will work according to the preset modes.
4. Restore the factory settings: press the “MODE” and “SETUP”, let the fixture power, loosen the key after two
seconds, the system will be reset, then restore factory settings.
Loading...