Owner's Operator And Maintenance Manual
TMTM
Infinity LoBack Support
DEALER: THIS MANUAL MUST BE GIVEN TO THE USER
OF THE WHEELCHAIR.
USER: BEFORE USING THIS WHEELCHAIR, READ THIS
MANUAL AND SAVE FOR FUTURE REFERENCE.
SPECIAL NOTES/T ABLE OF CONTENTS
S
P
E
C
A
L
N
O
T
E
S
WARNING
THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY A
QUALIFIED TECHNICIAN.
I
DO NOT INST ALL OR USE THIS EQUIPMENT WITHOUT FIRST
READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE
UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND
INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL,
DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE
A TTEMPTING TO INSTALL OR USE THIS EQUIPMENT - OTHER WISE
INJURY OR DAMAGE MAY RESUL T.
SPECIAL NOTES
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices which
could result in personal injury or property damage.
T
A
B
L
E
O
C
O
N
T
E
N
T
S
SPECIAL NOTES................................................ 2
F
SAFETY SUMMARY ...........................................3
IMPORT ANT INFORMATION...............................5
INST ALLATION/ADJUSTMENT OVERVIEW ........ 5
PROCEDURE 1 - PREP ARING WHEELCHAIR .... 6
INSTALLING/REMOVING CANE CLAMPS ........ 6
PROCEDURE 2 - PREP ARING THE
INFINITY LOBACK FOR INST ALLA TION .......... 7
INSTALLING/REMOVING THE
LATERAL SUPPORTS ...................................7
INSTALLING/REMOVING THE BACK
CUSHION ..................................................... 8
INSTALLING/REMOVING THE MODESTY
FLAP ............................................................ 9
SAVE THESE INSTRUCTIONS
TABLE OF CONTENTS
PROCEDURE 3 - INST ALLING/REMOVING THE
INFINITY LOBACK......................................... 10
INSTALLING/REMOVING THE INFINITY
LOBACK ..................................................... 10
PROCEDURE 4 - ADJUSTING THE
INFINITY LOBACK......................................... 11
ADJUSTING THE MOUNTING
HARDWARE/HEIGHT ................................. 11
ADJUSTING THE DEPTH HARDWARE .......... 11
ADJUSTING THE ANGLE ............................... 12
ADJUSTING THE LATERAL SUPPORTS ........ 13
PROCEDURE 5 - MAINTENANCE ..................... 15
INSTALLING/REMOVING CUSHION FOAM .... 15
INSPECTION ................................................. 15
CLEANING .................................................... 15
LIMITED W ARRANTY .................... BACK COVER
2
SAFETY SUMMARY
SAFETY SUMMARY
NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact your Dealer for further instruction.
INST ALLATION WARNINGS
Stabilize from the ground up. A stable base, pelvis and footrests are requirements for any torso
positioning system.
For proper installation of the Infinity LoBack and to reduce the risk of pressure sores, the adjustment procedures in this manual MUST be performed in the following order:
1. Adjusting the Mounting Hardware/Height
2. Adjusting the Depth Hardware
3. Adjusting the Angle
4. Adjusting the Lateral Supports
Ensure the cane clamps that secure the Infinity LoBack to the wheelchair are properly secured to
the wheelchair BEFORE using. Otherwise, changes in seat depth will occur, making the wheelchair less stable.
After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur.
ST ABILITY WARNINGS
The seat height, seat depth, back height, tilt angle, back angle, pivot point of seat frame, seating
system, caster position, size and position of the rear wheels, wheel locks, anti-tippers, locking collar as well as the user condition directly relate to the stability of the wheelchair. Any change to
one (1) or any combination of the fourteen (14) may cause the wheelchair to decrease in stability. Use EXTREME caution when using a new seating position.
S
A
F
E
T
Y
S
U
M
M
A
R
Y
Seat Height
Back Height
Seat Depth
Back Angle
Seating System
Tilt Angle
Seat Frame Pivot Point
Caster Position
Rear Wheel Size
Rear Wheel Position
User Condition
Wheel Locks
Anti-Tippers
Locking Collar
Seat Dump
Seat Height
Back Height
Seat Depth
Back Angle
Seating System
Tilt Angle
Seat Frame Pivot Point
Caster Position
Rear Wheel Size
Rear Wheel Position
User Condition
Seat Dump
Locking Collar
●●
●
●●
●●
●
●●
●●
●
●●
✓✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
●●
✓✓
●
✓
●●
✓✓
✓✓
●●
✓
●
✓✓
●●
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
●●
✓✓
●
✓
●●
✓✓
✓✓
●●
✓
●
✓✓
●●
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
●●
✓✓
●
✓
●●
✓✓
✓✓
●●
✓
●
✓✓
●●
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
●●
✓✓
●
✓
●●
✓✓
✓✓
●●
✓
●
✓✓
●●
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓✓
✓
✓
✓✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
✓✓
✓
✓✓
●●
●
●●
●●
●
●●
NOTE: When changes to the left hand column occur, follow across the chart and refer to the ✓ procedure to
maintain the proper stability, safety and handling of the wheelchair.
NOTE: Additional adjustments may be needed according to the wheelchair type. Refer to the wheelchair
owner's manual for these procedures.
3
SAFETY SUMMARY
S
A
F
E
T
Y
S
U
M
M
A
R
Y
SAFETY SUMMARY
ST ABILITY W ARNINGS (CONTINUED)
AL W AYS make sure wheelchair is stable BEFORE reclining the back system. Rear wheels may have
to be repositioned rearward depending on the degree of recline. ALWAYS ensure stability BEFORE
using maximum amount of recline. TEST wheelchair BEFORE it is occupied by end user to ensure
stability.
To maintain the stability of the wheelchair when moving the r ear wheels to ANY forward position,
the amount of recline MUST be limited to prevent the wheelchair from tipping onto the antitippers.
The necessary back angle MUST be selected BEFORE repositioning rear wheels forward.
AS REGARDS RESTRAINTS - SEAT POSITIONING STRAPS - IT IS THE OBLIGATION OF THE DME DEALER,
THERAPISTS AND OTHER HEALTH CARE PROFESSIONALS TO DETERMINE IF A SEAT POSITIONING STRAP
IS REQUIRED TO ENSURE THE SAFE OPERATION OF THIS EQUIPMENT BY THE USER. SERIOUS INJURY
CAN OCCUR IN THE EVENT OF A FALL FROM A WHEELCHAIR.
SEATING PRESSURE WARNING
Skin condition should be checked very frequently after the installation and use of any new seating system.
GENERAL WARNINGS
Care should be taken to prevent the hook and loop fasteners from becoming wet. Prolonged
contact with moisture may reduce the hold of the hook and loop fastners.
4
IMPORT ANT INFORMA TION/INST ALLA TION/ADJUSTMENT OVERVIEW
IMPORTANT INFORMATION
The best way to avoid problems related to pressure sores
is to understand their causes and your role in a skin management program.
Your therapist and physician should be consulted if you
have any questions regarding weight relief, self-examination of skin, or individual limitations and needs.
All cushions should be selected carefully. Working with
your therapist, physician and equipment supplier is the
best way to assure that a cushion choice matches your
individual needs.
As the needs of the client become more complex, the
cushion evaluation becomes more important.
INSTALLATION/ADJUSTMENT OVERVIEW
INSTALLATION/ADJUSTMENT OVERVIEW (FIGURE 1)
WARNING
For proper installation of the Infinity LoBack and to reduce the risk of pressure sores, the adjustment
procedures in this manual MUST be performed in the following order:
1. Adjusting the Mounting Hardware/Height
2. Adjusting the Depth Hardware
Follow the steps below in order. Refer to the procedure below each step.
STEP 2
Install/remove the lateral
supports. Refer to
REMOVING THE
LATERAL SUPPORTS in
PROCEDURE 2 of this manual.
INSTALLING/
Adjust the lateral supports.
Refer to
LATERAL SUPPORTS in
PROCEDURE 4 of this
STEP 8
ADJUSTING THE
manual.
3. Adjusting the Angle
4. Adjusting the Lateral Supports
STEP 3
Install the back cushion. Refer
to
INSTALLING/REMOVING
THE BACK CUSHION in
PROCEDURE 2
of this manual.
I
N
F
O
R
M
A
T
I
O
N
STEP 7
Adjust the angle.
Refer to
ING ANGLE in
PROCEDURE 4 of
Install the cane
clamps onto the
wheelchair. Refer to
INSTALLING/
REMOVING CANE
CLAMPS in PRO-
CEDURE 1 of this
ADJUST-
this manual.
STEP 1
manual.
STEP 5
Adjust the height of the Infinity
LoBack. Refer to
THE MOUNTING HARDWARE/
HEIGHT in PROCEDURE 4 of
this manual.
ADJUSTING
STEP 4
Install the Infinity LoBack.
Refer to
REMOVING THE INFIN-
ITY LOBACK in PROCE-
DURE 3 of this manual.
Adjust the depth of the Infinity
LoBack. Refer to
THE DEPTH HARDWARE in
PROCEDURE 4 of this manual.
INSTALLING/
STEP 6
ADJUSTING
O
V
E
R
V
I
E
W
FIGURE 1 - INST ALLATION/ADJUSTMENT OVERVIEW
5
PROCEDURE 1
PREP ARING WHEELCHAIR
P
This Procedure includes the following:
R
E
Installing/Removing Cane Clamps
P
A
INSTALLING/REMOVING CANE
R
I
CLAMPS (FIGURE 1)
N
G
W
H
E
E
L
C
H
A
R
After ANY adjustments, repair or service and
BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or
damage may result.
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
I
Installing Cane Clamps
WARNING
NOTE: The final mounting positions of the cane clamps
will be determined by the adjustments made to the Infinity LoBack to fit the wheelchair and user.
1. Remove the existing back upholstery. Refer to the
wheelchair Owner's Manual.
2. Hold the Infinity LoBack up to the back canes at the
desired mounting height.
3. Visually inspect the location of the clamps on the Infinity LoBack to determine the proper positions for
each cane clamp.
Removing Cane Clamps
1. Remove the Infinity LoBack from the wheelchair.
Refer to
REMOVING THE INFINITY LOBACK in
PROCEDURE 3 of this manual.
2. Loosen, but do not remove the two (2) mounting
screws on the two (2) cane clamps.
3. Remove the two (2) cane clamps from the two (2)
back canes of the wheelchair.
Cane Clamp
Mounting Screw
(Faces TOWARD
the REAR of the
Wheelchair)
4. Loosen, but do not remove the mounting screw on
one (1) of the cane clamps.
5. Position the cane clamp on one (1) back cane, making sure that the HEAD of the mounting screw faces
TOWARD the REAR of the wheelchair . Hand tighten
ONLY.
NOTE: It is NOT necessary to tighten the two (2) mounting screws on the two (2) cane clamps at this time. The
two (2) cane clamps will be adjusted AFTER the Infinity
LoBack has been installed on the wheelchair and the
user has been evaluated.
6. Repeat STEPS 5-6 to install the other cane clamp on
the opposite back cane.
NOTE: Make sure that the two (2) cane clamps are in the
position determined in STEP 3 AND that the two (2) cane
clamps are in the same position on each back cane by
measuring the distance from the bottom of each back cane
to the bottom of each cane clamp.
Back Cane
FIGURE 1 - INST ALLING/REMOVING CANE
CLAMPS
6
PREP ARING THE INFINITY LOBACK FOR INSTALLATION PROCEDURE 2
This Procedure includes the following:
Installing/Removing the Lateral Supports
Installing/Removing the Back Cushion
Installing/Removing the Lower Flap
INSTALLING/REMOVING THE
LATERAL SUPPORTS (FIGURE 1)
WARNING
After ANY adjustments, repair or service and
BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or
damage may result.
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
Installing
NOTE: The final mounting positions of the lateral supports will be determined by the adjustments made to the
Infinity LoBack to fit the wheelchair and user.
1. Remove the back cushion from the back panel. Refer to
INSTALLING/REMOVING THE BACK CUSH-
ION in this procedure of the manual.
NOTE: The lateral supports can be adjusted to three (3)
different height positions (DETAIL “A”).
2. Align the upper, middle or lower mounting holes in
the lateral support with the toothed adjustment slots
in the back panel (DETAIL “A”).
NOTE: The grooves next to the mounting holes in the
lateral supports are provided to ensure that opposite lateral supports are installed using the SAME mounting holes
(FIGURE 1). To ensure that this occurs, install one (1)
lateral support at the desired height and look through the
toothed adjustment slot to see which mounting holes have
been used. Then, install the opposite lateral support using the SAME mounting holes.
Removing
1. Remove the back cushion from the back panel. Refer
to
INSTALLING/REMOVING CUSHIONS in this pro-
cedure of the manual.
2. Remove the (2) mounting screws and washers securing the lateral support to the back panel.
3. Remove the lateral support.
4. Repeat STEPS 2-3 for the remaining lateral supports,
if necessary.
DET AIL “A”
Upper
Mounting
Lateral
Support
Holes
Middle
Mounting
Holes
Lower
Mounting
Holes
Toothed
Adjustment
Lateral
Slot
Support
Grooves
P
R
E
P
A
R
I
N
G
T
H
E
L
O
B
A
C
K
F
O
R
I
N
S
T
A
L
L
A
T
I
O
N
3. Install the two (2) mounting screws and washers that
secure the lateral support to the back panel. Hand
tighten ONLY.
NOTE: It is NOT necessary to tighten the mounting screws
on the lateral support at this time. The lateral supports will
be adjusted AFTER the Infinity LoBack has been installed
on the wheelchair and the user has been evaluated.
4. Repeat STEPS 2-3 to install the OPPOSITE lateral
support.
5. Reinstall the back cushion onto the back panel. Re-
INSTALLING/REMOVING THE BACK CUSH-
fer to
ION in this procedure of the manual.
Mounting
Screws
Back Panel
FIGURE 1 - INST ALLING/REMOVING THE
LATERAL SUPPORTS
7
PROCEDURE 2 PREP ARING THE INFINITY LOBACK FOR INSTALLATION
INSTALLING/REMOVING THE BACK
P
R
CUSHION (FIGURE 2)
E
P
NOTE: Refer to the INSTALLATION AND STABILITY
A
R
WARNINGS in the SAFETY SUMMARY of this manual.
I
N
G
CAUTION
The cushion covers are designed to protect the
T
H
E
L
O
B
A
C
K
foam against moisture and to provide fire
retardency. DO NOT use the back without the
covers. If the covers are torn, they MUST be replaced immediately.
NOTE: Invacare recommends the use of a fire retardent
cushion with the Infinity LoBack.
Installing
1. Lift up on the modesty flap AND the fixed flap that
covers the BACK of the cushion, and fold them so
they hang over the FRONT of the cushion.
NOTE: Modesty flap and fixed flap not shown in DETAIL “A” and DETAIL “B” for clarity.
DET AIL “A”
2. Align the hook and loop fasteners on the BACK of the
cushion with the hook and loop fasteners on the
FRONT of the back panel (DETAIL “A”).
NOTE: Make sure the cushion is centered on the back panel.
3. Make sure the hook and loop fasteners meet by firmly
pushing the cushion and back panel together. (DETAIL “A”).
4. Grasp the folding hook and loop fastener on the cushion and fold them over the TOP of the back panel,
making sure they meet the hook and loop fastener
on the BACK of the back panel (DETAIL “A”).
5. Grasp the fixed flap AND the modesty flap and fold
them so they cover the BACK of the back panel.
6. Align the two (2) hook and loop fasteners at the TOP
of the modesty flap with the two (2) hook and loop
fasteners at the BOTTOM of the cushion (DETAIL “B”).
DET AIL “B”
NOTE: Front of back panel/ hook and loop fastener (STEP
2-3) not shown for clarity.
F
O
R
Folding Hook
I
N
S
T
A
L
L
A
T
I
O
N
and Loop
Fasteners
NOTE: Modesty flap
and fixed flap should
hang on front side of
the cushion during
installation/removal.
Back of
Cushion
Top of
Back Panel
Hook and
Loop
Fastener
Top of
Back
Panel
Hook and
Loop
Fastener
Hook and
Loop
Fasteners
Bottom of
Cushion
Top of
Modesty Flap
TOP VIEW
Bottom of Cushion
Hook and
Loop
Fasteners
Hook and
Loop
Fastener
Top of
Hook and
Fasteners
Back of
Back Panel
Modesty
Flap
FIGURE 2 - INST ALLING/REMOVING THE BACK CUSHIONS
8
Loop
PROCEDURE 2PREP ARING THE INFINITY LOBACK FOR INSTALLATION
7. Make sure the hook and loop fasteners meet by firmly
pushing the TOP of the modesty flap and the BOTTOM of the cushion together.
Removing
1. Grasp the modesty flap AND the fixed flap.
2. Pull UP to release the two (2) hook and loop fasteners on the TOP of the modesty flap from the two (2)
hook and loop fasteners on the BOTTOM of the cushion (DETAIL “B”).
2. Fold the modesty flap AND the fixed flap over the
FRONT of the cushion.
3. Grasp the two (2) folding hook and loop fasteners on
the cushion and pull UP to release them from the two
(2) hook and loop fasteners on the BACK of the back
panel (DETAIL “A”).
4. Grasp the cushion and pull it away from the back
panel to release the remaining hook and loop fasteners on the cushion and back panel (DETAIL “A”).
5. Remove the cushion.
INSTALLING/REMOVING THE
MODESTY FLAP (FIGURE 3)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
Installing
1. Align the hook and loop fasteners at the TOP of the
REAR side of modesty flap with the hook and loop
fasteners at the BOTTOM of the FRONT side of the
fixed flap (DETAIL ”A”).
2. Make sure the hook and loop fasteners meet by firmly
pushing the TOP of the modesty flap and the BOTTOM of the fixed flap together (DETAIL “A”).
3. Align the two (2) hook and loop fasteners at the TOP
of the FRONT side of the modesty flap with the two
(2) folding hook and loop fasteners at the BOTTOM
of the REAR side of the cushion (DETAIL “B”).
4. Make sure the hook and loop fasteners meet by firmly
pushing the TOP of the modesty flap and the BOTTOM of the cushion together, making sure the hook
and loop fasteners meet (DETAIL ”B”).
Removing
1. Grasp the two (2) hook and loop fasteners at the
TOP of the FRONT side of the modesty flap and pull
UP to release them from the two (2) hook and loop
fastener at the BOTTOM of the REAR side of the
cushion (DETAIL “B”).
2. Grasp the modesty flap and pull DOWN to release
the hook and loop fasteners at the TOP of the REAR
side of the modesty flap from the hook and loop fasteners at the BOTTOM of the FRONT side of the
fixed flap (DETAIL “A”).
3. Remove the modesty flap.
DET AIL “A”
NOTE: The hook and loop fasteners on the front side of
the fixed flap are not shown for clarity.
Hook and Loop
Fasteners
Bottom of
Fixed Flap
Top of Modesty Flap
Rear Side
DET AIL “B”
Folding Hook and
Loop Fasteners
Bottom Of
Cushion
Top of
Modesty
Flap
Hook And Loop Fasteners
FIGURE 3 - INST ALLING/REMOVING THE
MODESTY FLAP
P
R
E
P
A
R
I
N
G
T
H
E
L
O
B
A
C
K
F
O
R
I
N
S
T
A
L
L
A
T
I
O
N
9
PROCEDURE 3 INST ALLING/REMOVING THE INFINITY LOBACK
I
This Procedure includes the following:
N
Installing/Removing the Infinity LoBack
S
T
A
INSTALLING/REMOVING THE
L
L
INFINITY LOBACK (FIGURE 1)
I
N
G
/
R
E
M
O
V
N
G
After ANY adjustments, repair or service and
BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or
damage may result.
I
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
WARNING
Installing the Infinity LoBack
1. Ensure the two (2) cane clamps are properly installed
onto the wheelchair frame. Refer to INSTALLING/
REMOVING CANE CLAMPS in PROCEDURE 1 of
this manual.
2. If necessary, adjust the Infinity LoBack to fit on the
back canes. Refer to
ADJUSTING THE INFINITY
LOBACK in PROCEDURE 4 of this manual.
3. Align the mounting holes in the two (2) Infinity LoBack
mounting clamps with the locking pins on the two (2)
cane clamps (FIGURE 1).
4. Lower the Infinity LoBack onto the wheelchair back
T
H
E
canes, making sure the locking pins on the two (2)
cane clamps pass through the mounting holes in the
two (2) mounting clamps of the Infinity LoBack.
L
5. Firmly grasp the handle of the locking pin and bend it
O
B
A
C
K
DOWN until it forms a 90
locking pin, then push it FORWARD to fully engage
the lock. (DETAIL “A”).
o
angle with the rest of the
NOTE: The locking pin is fully engaged when the handle
of the locking pin bends down to form a 90° angle with the
rest of the of the locking pin.
A. ADJUSTING THE MOUNTING HARDWARE/
HEIGHT
B. ADJUSTING THE DEPTH HARDWARE
C. ADJUSTING THE ANGLE
D. ADJUSTING THE LA TERAL SUPPORTS
NOTE: Perform the above procedures in the order listed.
11. Inspect all mounting screws to ensure ALL hardware
has been tightened securely. Torque to 45-50 in./lbs.
13. If necessary, repeat STEPS 8-11 until the user is com-
fortable.
Removing the Infinity LoBack
1. Grasp the handle of one (1) of the locking pins and
push it BACK to release the lock, and then pull it UPWARD until the handle is parallel with the rest of the
locking pin.
2. Repeat STEP 5 for the opposite locking pin.
3. Grasp the Infinity Loback from the bottom and pull
upward to release it from the mounting pins on the
two (2) cane clamps.
4. Remove the Infinity LoBack.
DET AIL “A”
Pull Handle
Handle
Forward to
Engage Lock
Locks to
Form A
90o Angle
Locking
Pin
Infinity LoBack
Mounting
Clamp
6. Repeat STEP 5 for the opposite locking pin.
7. Ensure all cushions and lateral supports have been installed. Refer to
PREPARING THE INFINITY BACK
FOR INSTALLATION in PROCEDURE 2 of this
manual.
8. Position the user into the wheelchair to determine
which adjustments need to be made to properly fit
the Infinity LoBack. Refer to the wheelchair owner’s
manual.
9. Remove the user from the wheelchair. Refer to the
wheelchair owner’s manual.
10. Perform the following procedures to adjust the Infinity LoBack to fit the user if necessary. Refer to
AD-
JUSTING THE INFINITY LOBACK in PROCEDURE
4 of this manual.
Mounting Hole
Locking Pin
Cane Clamp
Back Cane
FIGURE 1 - INST ALLING/REMOVING THE INFINITY
LOBACK
10
PROCEDURE 4ADJUSTING THE INFINITY LOBACK
This Procedure includes the following:
Adjusting the Height
Adjusting the Depth Hardware
Adjusting the Angle
Adjusting the Lateral Supports
W ARNING
For proper installation of the Infinity LoBack and
to reduce the risk of pressure sores, the adjustment procedures below MUST be performed in
the following order:
1. Adjusting the Mounting Hardware/Height
2. Adjusting the Depth Hardware
3. Adjusting the Angle
4. Adjusting the Lateral Supports
NOTE: After performing each procedure, place the user
in the wheelchair and inspect to ensure the correct adjustments have been made for user comfort. If necessary, repeat the procedure until the user is comfortable.
ADJUSTING THE MOUNTING
HARDWARE/HEIGHT (FIGURE 1)
6. Torque the mounting screw to 45-50 in./lbs.
7. Repeat STEPS 2-6 for the opposite cane clamp.
NOTE: Make sure that the two (2) cane clamps are in the
same position on each back cane by measuring the distance from the bottom of each back cane to the bottom of
each cane clamp.
9. Reinstall the Infinity LoBack onto the wheelchair. Refer
to
INSTALLING/REMOVING THE INFINITY
LOBACK in PROCEDURE 3 of this manual,
Cane
Clamp
Move Up
Or Down
A
D
J
U
S
T
I
N
G
T
H
E
L
O
B
A
C
K
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
1. Remove the Infinity LoBack from the wheelchair. Refer
to
INSTALLING/REMOVING THE INFINITY
LOBACK in PROCEDURE 3 of this manual,
2. Loosen the mounting screw on the cane clamp.
3. Move the cane clamp up or down until the desired
position is acheived.
ADJUSTING THE DEPTH
HARDWARE
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
NOTE: The depth of the Infinity LoBack can be adjusted by
maneuvering the cane clamps AND/OR by pivoting the adjustment brackets.
Adjusting the Cane Clamps (Figure 2)
1. Remove the Infinity LoBack from the wheelchair. Refer
INSTALLING/REMOVING THE INFINITY
to
LOBACK in PROCEDURE 3 of this manual,
2. Hold the Infinity LoBack up to the wheelchair.
3. Visually inspect the Infinity LoBack and the wheelchair to determine the desired depth.
Mounting
Screw
FIGURE 1 - ADJUSTING THE MOUNTING
HARDWARE/HEIGHT
4. Loosen the two (2) mounting screws on the two (2)
cane clamps.
5. Perform one (1) of the following to achieve the desired depth:
A. To INCREASE depth, rotate the two (2) cane
clamps so that the locking pins are facing the
REAR of the wheelchair.
B. To DECREASE depth, rotate the two (2) cane
clamps so that the locking pins are facing the
FRONT of the wheelchair.
NOTE: By rotating the locking pins on the cane clamps
toward the front or rear of the wheelchair, numerous depth
positions can be achieved.
6. Torque the two (2) mounting screws on the two (2)
cane clamps to 45-50 in./lbs.
11
PROCEDURE 4 ADJUSTING THE INFINITY LOBACK
7. Reinstall the Infinity LoBack onto the wheelchair. Refer
A
D
J
U
S
T
I
N
G
to
INSTALLING/REMOVING THE INFINITY
LOBACK in PROCEDURE 3 of this manual.
Locking Pin
Cane Clamps
Mounting
Screws
T
H
E
L
O
B
A
C
K
FRONT
Rotate
Cane
Clamps
Toward
Front to
DECREASE
Depth
TOP VIEW
REAR
Cane Clamp
INCREASE
Depth
Locking
Pin
DECREASE
FRONT
FIGURE 2 - ADJUSTING THE CANE CLAMPS
Rotate
Cane
Clamps
Toward
Rear to
INCREASE
Depth
REAR
To
To
Depth
NOTE: When loosening the mounting screws/nuts, it is
necessary to firmly hold the nuts in place while turning
the mounting screws.
5. Perform one (1) of the following to achieve the desired depth:
A. To INCREASE depth, pivot the two (2) adjust-
ment brackets so that the mounting screws and
nuts are facing the REAR of the chair.
B. To DECREASE depth, pivot the two (2) adjust-
ment brackets so that the mounting screws and
nuts are facing the FRONT of the chair.
6. Torque the two (2) mounting screws and nuts to 4550 in./lbs (DETAIL “B”).
7. Reinstall the Infinity LoBack onto the wheelchair. Refer
INSTALLING/REMOVING THE INFINITY
to
LOBACK in PROCEDURE 3 of this manual.
FRONT
Adjustment
Mounting
Screw
Bracket
Should be
Angled
Toward
Front to
DECREASE
REAR
Depth
Adjustment Bracket
Should be
Angled Toward
Rear to INCREASE
Adjustment
Bracket
Nut
Depth
TOP VIEW
To
REAR
INCREASE
Depth
Adjustment
Bracket
Pivoting The Adjustment Brackets (Figure 3)
1. Remove the Infinity LoBack from the wheelchair. Refer
to
INSTALLING/REMOVING THE INFINITY
LOBACK in PROCEDURE 3 of this manual,
2. Hold the Infinity LoBack up to the wheelchair.
3. Visually inspect the Infinity LoBack and the wheelchair to determine the desired depth.
4. Loosen the two (2) mounting screws and nuts on the
two (2) adjustment brackets.
12
Mounting Screw
To
DECREASE
Depth
FRONT
FIGURE 3 - PIVOTING THE ADJUSTMENT
BRACKETS
PROCEDURE 4ADJUSTING THE INFINITY LOBACK
ADJUSTING THE ANGLE (FIGURE 4)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
1. Remove the back cushion from the back panel. Refer to
INSTALLING/REMOVING THE BACK CUSH-
ION in PROCEDURE 2 of the manual.
2. Loosen the two (2) mounting screws on the two (2)
angle brackets.
3. While standing behind the wheelchair, perform one
(1) of the following:
A. To INCREASE the angle of the Infinity LoBack, grasp
the TOP of the Infinity LoBack and pull BACK.
NOTE: Modesty flap and fixed flap not shown for clarity.
TO DE-
CREASE
ANGLE:
Grasp Here
and Push
FORWARD
TO INCREASE
ANGLE:
Grasp Here
and Pull
BACK
B. To DECREASE the angle of the Infinity LoBack,
grasp the TOP of the Infinity Loback and push
FORWARD.
4. Torque the two (2) nuts on the two (2) angle brackets
to 45-50 in./lbs.
5. Reinstall the back cushion onto the back panel. Re-
INSTALLING/REMOVING THE BACK CUSH-
fer to
ION in PROCEDURE 2 of the manual.
ADJUSTING THE LATERAL
SUPPORTS
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
Adjusting the Width (Figure 5)
1. Remove the back cushion from the back panel. Re-
INSTALLING/REMOVING THE BACK CUSH-
fer to
ION in PROCEDURE 2 of the manual.
2. Loosen, but DO NOT remove the two (2) mounting
screws that secure the lateral support to the back
panel.
3. Position the user in the wheelchair.
4. Slide one (1) lateral support to the desired location.
5. Torque the two (2) mounting screws that secure the
lateral support to the back panel to 45-50 in./lbs.
6. Repeat STEPS 1-4 for the remaining lateral support.
7. Reinstall the back cushion onto the back panel. Re-
INSTALLING/REMOVING THE BACK CUSH-
fer to
ION in PROCEDURE 2 of the manual.
A
D
J
U
S
T
I
N
G
T
H
E
L
O
B
A
C
K
Angle Bracket
Mounting
Screw
SIDE VIEW
TO DE-
CREASE
ANGLE:
Grasp Here
and Push
FORWARD
FIGURE 4 - ADJUSTING THE ANGLE
TO INCREASE
ANGLE:
Grasp Here
and Pull
BACK
Back Panel
Slide Lateral
Support to the
Desired Location
Lateral
Support
Mounting
Screws
NOTE: Modesty flap and fixed flap not shown for clarity.
FIGURE 5 - ADJUSTING THE WIDTH
13
PROCEDURE 4 ADJUSTING THE INFINITY LOBACK
A
D
NOTE: The lateral supports can be adjusted to three (3)
J
U
different height positions (DETAIL “A”).
S
1. Remove the back cushion from the back panel. Re-
T
I
N
G
T
H
E
L
O
B
A
C
K
fer to
INSTALLING/REMOVING THE BACK CUSH-
ION in PROCEDURE 2 of the manual.
2. Remove the two (2) mounting screws securing the
lateral support to the back panel.
3. Position the lateral support in the upper, middle or
lower position, aligning the mounting holes of the lateral support with the toothed adjustment slot in the
back panel (DETAIL “A”).
NOTE: The grooves next to the mounting holes in the
lateral supports are provided to ensure that opposite lateral supports are installed using the SAME mounting
holes. To ensure that this occurs, install one (1) lateral
support at the desired height position and look through
the toothed adjustment slot to see which mounting holes
have been used. Then, install the opposite lateral support using the SAME mounting holes.
4. Install the two (2) mounting screws to secure the supports to the back panel.
5. Repeat STEPS 1-3 for the remaining lateral support.
6. Torque the two (2) mounting screws that secure the
lateral support to the back panel to 45-50 in./lbs.
7. Adjust the width of the lateral supports. Refer to
JUSTING THE WIDTH in this procedure of the manual.
8. Reinstall the back cushion onto the back panel. Re-
INSTALLING/REMOVING THE BACK CUSH-
fer to
ION in PROCEDURE 2 of the manual.
AD-
DET AIL “A”Adjusting the Height (Figure 6)
Upper
Mounting
Lateral
Support
Holes
Middle
Mounting
Holes
Lower
Mounting
Holes
Toothed
Adjustment
Lateral
Slot
Support
Grooves
Mounting
Screws
Back Panel
NOTE: Modesty flap and fixed flap not shown for clarity.
14
FIGURE 6 - ADJUSTING THE HEIGHT
MAINTENANCE PROCEDURE 5
This Procedure includes the following:
Installing/Remove Back Cushion Foam
Inspection
Cleaning
REPLACING THE BACK CUSHION
FOAM (FIGURE 1)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
1. Remove the back cushion from the back panels. Refer
to
INSTALLING/REMOVING THE BACK CUSH-
IONS in PROCEDURE 2 of this manual.
2. Position the back cushion on a flat surface with the
zipper facing UPWARDS.
3. Unzip the zipper.
4. Grasp the EXISTING cushion foam and remove it
from the back cover.
5. Align the NEW cushion foam with the hole in the back
cover.
NOTE: Make sure the plastic insert on the NEW cushion
foam is facing the REAR of the back cover and that the
fingers on the plastic insert face the TOP of the back
cover.
6. Position the NEW cushion foam inside the back cover.
7. Position the zipper inside the pouch.
8. Reinstall the back cushion onto the back panels. Re-
INSTALLING/REMOVING THE BACK CUSH-
fer to
IONS in PROCEDURE 2 of this manual.
Back Cover
INSPECTION
WARNING
INITIALLY AND ONCE A WEEK, visually inspect
all parts, including hardware, upholstery materials, foams (if accessible), and plastics for
deformation, corrosion, breakage, wear and/
or compression.
Check ALL fasteners weekly to ensure that mechanical connections are secure.
DO NOT continue to use this product if any of
the conditions described above are discovered.
NOTE: Corrective maintenance can be performed at or
arranged through your equipment supplier.
W ARNING
Skin condition should be checked very frequently
after the installation and use of any new seating system.
CLEANING
Cover
1. Machine wash the back covers in cold water on gentle
cycle using a mild detergent ONCE A WEEK.
WARNING
When washing the back covers - DO NOT use
fabric softeners or bleach. DO NOT machine
dry. Air dry ONL Y. DO NOT dry in sun.
Failure to follow the washing instructions CAN
reduce the flame retardency of the back
cover.
Foam
M
A
I
N
T
E
N
A
N
C
E
Fingers
Plastic
Insert
Rear of Cushion
FIGURE 4 - REPLACING THE BACK
CUSHION FOAM
Care should be taken to prevent the back cushion foam
from getting wet. If the back cushion foam begins to deteriorate from prolonged contact with moisture, it should be
replaced immediately.
Zipper
Cushion
Foam
15
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
Invacare warrants its products to be free from defects in materials and workmanship for use by
the original purchaser for a period of two (2) years from the date of purchase on the back and
ninety (90) days from the date of purchase on the cover. If within such warranty period any such
product shall be proven to be defective, such product shall be repair ed or replaced, at Invacare's
option. This warranty does not include any labor or shipping charges incurred in replacement
part installation or repair of any such product. Invacare's sole obligation and your exclusive remedy under this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacar e pr oduct. In the event you do not receive satisfactory warranty service, please write directly to Invacare at the address at the bottom of this page. Provide dealer’s name, address, date of pur chase,
indicate nature of the defect and, if the product is serialized, indicate the serial number. Do not
return products to our factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED, PRODUCTS SUBJECTED
TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE OR STORAGE, COMMERCIAL
OR INSTITUTIONAL USE, PRODUCTS MODIFIED WITHOUT INVACARE'S EXPRESS WRITTEN CONSENT
INCLUDING, BUT NOT LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR
ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES
BEYOND INVACARE'S CONTROL, AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE
TO ADHERE TO THESE INSTRUCTIONS.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, IF ANY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESSED
WARRANTY PROVIDED HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY
SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE
TERMS CONTAINED HEREIN. INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND REQUIREMENTS.
Invacare Corporation www.invacare.com
USA Canada
One Invacare Way 5970 Chedworth Way Invacare is a registered trademark of Invacare Corporation.
Elyria, Ohio USA Mississauga, Ontario ©
44036-2125 L5R 3T9, Canada
800-333-6900 905-890-8838 Form No. 99-221 Part No. 1095174 Rev A (1) 02/00
1999 Invacare Corporation
Loading...