303
PO
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
English
OWNER’S MANUAL
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
For illustrative purposes only. Pool not included.
Hydro Flow™ Swim Trainer
Model SM24101
110-120V AC / 60Hz
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, Visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
303-*PO-R0-1702
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual without notice.
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 2
Warnings
..................................................................................... 3
Parts Reference
..........................................................................
4-5
Product Specification
................................................................
6
Setup Instructions
......................................................................
6-13
Operating Instructions
...............................................................
14-15
Maintenance
...............................................................................
15
Internal Parts Replacements
.....................................................
16-17
Troubleshooting Guide
..............................................................
18-19
Limited Warranty
.........................................................................
20
TABLE OF CONTENTS
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 3
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• To reduce the risk of injury, do not permit children to use this product. Always supervise children and those with
disabilities.
• Children must stay away from this product and electrical cord(s).
• Assembly and disassembly by adults only.
• Cleaning and user maintenance must be performed by adults only who understand the risk of electric shock.
• For domestic pool use only. Not for commercial use.
• Risk of electric shock. If replacement of the plug or cord is needed, use only identical replacement parts.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment
to the product.
• Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit
interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the
receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum
rate of 30mA. Do not use a portable residual current device (PRCD).
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and
other equipment.
•
To reduce the risk of electric shock, replace damaged cord immediately. Use a qualified electrician to replace the cord.
• To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to
connect unit to electric supply; provide a properly located outlet.
• The appliance is only to be used with the provided transformer.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
•
Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI since the ALCI will not protect people.
• Position the transformer away from the pool, so as to prevent children from climbing on it and accessing the pool.
• Pool covers must be completely removed before using this product.
• People using medications and/or having an adverse medical history should consult a physician before
using this product.
• Do not use drugs or alcohol before or during the use of this product.
• Do not use this product when it is snowing, raining, thundering or lightning.
• Do not use this product immediately following strenuous exercise.
• Do not sit, straddle, step or exert pressure on the product as injury could occur.
• Never play or swim near the swim trainer vent holes.
• Keep hair away from the swim trainer vent holes. Your hair may be trapped causing permanent injury or drowning.
Wear a swim cap.
• Do not obstruct the swim trainer vent holes.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC SHOCK,
ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 4
Intex Rectangular Frame Pool Mounting Bracket
In Ground Pool Mounting Bracket
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
5
4
1
4
7
8
6
9
2
4
3
15
9
8
8
6
7
10
12
11
14
13
2
Intex Round Frame Pool Mounting Bracket.
NOTE:
Drawings for illustration purpose only. Actual product may vary. Not to scale.
REF. NO.
DESCRIPTION QTY.
IGP
POOL
Intex Rectangular
Frame Pool
Intex Round Frame
Pool
SPARE PART NO.
1
Mounting Bracket
1 12591
--
21
-
12592 12592
3 Bracket space filler 1
-
12593 12593
4 Mounting bracket screw 2 12396 12396 12396
5 Anchor screws 2 12407
--
6 Bracket pole 2
-
12594 12594
7 Bracket pole fixer 2
-
12595 12595
8 Screws 16
-
12598 12598
9 Pin 2
-
12406 12406
10 Horizontal pipe lugs 2
--
12597
11 A/B/C gap filler set 2
--
12405
12 Horizontal pipe fixer 2
--
12596
13 Horizontal pipe A 1
--
12403
14 Horizontal pipe B 1
--
12402
15 screws 4
-
12599 12599
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 5
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
REF. NO.
DESCRIPTION QTY.
IGP
POOL
Intex Rectangular
Frame Pool
Intex Round Frame
Pool
SPARE PART NO.
16 Display panel 1 12379 12379 12379
17 Display panel antenna 1 12391 12391 12391
18 Remote control 1 12381 12381 12381
19 Emergency stop lanyard 1 12374 12374 12374
20 Clamp knob 2 12395 12395 12395
21 Circuitry box 1 12387 12387 12387
22 Support bracket 1 12398 12398 12398
23 Support plate 1 12399 12399 12399
24 Adjustable bolt with nut 2 12397 12397 12397
25 Anchor adjustable bolt 2 12390
-
12390
26 Wheels 2 12389 12389 12389
27 Motor 1 12383 12383 12383
28 Transformer 1 12377 12377 12377
29 Transformer fuse 1 12394 12394 12394
30
Transformer fan
1 12393 12393 12393
31
Propeller kit
1 12385 12385 12385
32 Swim-trainer unit 1 12375 12375 12375
33 Adjustable bolt spacer 2 12600 12600 12600
16
18
19
20
31
21
22
23
24
25
33
26
29
28
30
27
4
17
32
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 6
• Pool must be fi lled with water prior to installation. Two adults required.
•
Tools required:
one Philip screwdriver, one fl at screwdriver and one small adjustable
wrench.
• Pool size requirements:
Pool water depth: 100cm (39 inch) minimum.
Pool length: 4.6m (15') minimum.
Pool width: 2.5m (8.2') minimum.
Transformer Location Requirement
1.
The transformer must be installed on a solid level and vibration-free area.
2.
Provide a location protected from the weather, moisture, rain, splashing water, fl ooding
and freezing temperature.
3.
Provide adequate access, space and lighting for routine maintenance.
4.
The transformer requires free circulation of air for cooling.
Swim-Trainer Unit and Support Bracket Assembly, for all type of pools.
NOTE: Make sure the pool wall is able to support a load of 25 kg (55 Lbs) or more
before installation.
Model:
SM24101
Voltage:
Transformer input 110-120V AC / 60Hz 8A
Transformer output 24V DC 35A
Suitable for:
In ground pool or Intex above ground metal frame pools
Pool water temperature range:
25ºC - 35ºC
* Approximate
PRODUCT SPECIFICATIONS
SETUP INSTRUCTIONS
Speed Setting*
12345678
m/s
0.66 0.77 0.83 0.94 0.98 1.06 1.16 1.21
ft/s
2.17 2.53 2.72 3.08 3.22 3.48 3.81 3.97
This device generates a constant flow of pool water that allows the user to swim
uninterrupted in the swimming pool.
25
20
24
22
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 7
Pool Mounting Bracket Assembly
A: For Intex Rectangular Frame Pools
1. Mounting Bracket Assembly (see fi gures 1.1 to 1.2)
:
NOTE:
Center the swim-trainer unit on the short-end side of the pool.
2. Installing the mounting bracket assembly onto a rectangular frame pool wall
(see fi gures 2.1 to 2.3)
SETUP INSTRUCTIONS (continued)
X
1 2
2.1
2
6
9
1.1
OR
1.2
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 8
1
2
3.2
Water level
90 Degree
•
Lock the bracket poles and mounting bracket assembly onto the U-shaped side
support with the bracket pole fi xer
(7)
and screws
(8). (see fi gure 2.2)
.
NOTE:
Make sure all the screws are securely tightened and the mounting bracket
top surface is level.
3. Swim-Trainer Unit Assembly (see fi gures 3.1 to 3.2).
• Be sure the swim-trainer unit “support bracket” is closed before installing the
swim-trainer unit onto the mounting bracket assembly
(see figure 3.1)
.
• Extend the support plate, and adjust the depth by loosening the arm collar and
extending the support plate arm until the swim-trainer unit is perfectly horizontal,
retighten to lock it in place.
NOTE:
The support plate must rest against the inside of
the pool wall surface.
(see fi gure 3.2)
.
SETUP INSTRUCTIONS (continued)
X X
2.32.2
7
8
XX
3.1
4
22
MIN
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 9
B: For Intex Round Frame Pools
1. Mounting Bracket Assembly (see figures 4.1 to 4.5):
• Identify the frame pool pipe shape. For “
” shape pipe see fi gure 4.2 to 4.5.
For “O” shape pipe see fi gure 4.3 to 4.5.
• For “
” shape pipe, remove the bracket space fi ller
(3)
from the mounting bracket
(2)
.
(see fi gure 4.2)
. For “O” shape pipe go to next step.
• Insert the bracket poles
(6)
into the mounting bracket
(2)
inner holes
(see fi gure 4.3)
.
• Connect the horizontal pipe A
(13)
with horizontal pipe B
(14)
together, then attach
the horizontal pipe assembly to the mounting bracket assembly using the bracket
pole fi xer
(7)
and screws
(8) (see fi gures 4.4 to 4.5)
.
SETUP INSTRUCTIONS (continued)
4.1
4.3
2
6
9
4.2
2
3
4.54.4
12
13
14
8
8
7
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 10
2. Installing the mounting bracket assembly onto a round frame pool wall
(see figures 5.1 to 5.3):
• Attach the mounting bracket assembly onto the frame pool vertical legs with the
horizontal pipe lugs
(10)
, screws
(8)
, and depending on the shape of the vertical leg
pipe include A/B/C gap fi ller
(11) (see fi gure 5.2).
For “
” shape vertical leg pipe, do not include the A/B/C gap fi ller
(11).
For 38mm diameter vertical leg pipe include “A” gap fi ller.
For 44mm diameter vertical leg pipe include “B” gap fi ller.
For 48mm diameter vertical leg pipe include “C” gap fi ller.
NOTE:
Make sure all the screws are securely tightened and the mounting bracket top
surface is level.
3. Swim-Trainer Unit Assembly (see fi gures 5.4 to 5.5).
• Be sure the swim-trainer unit “support bracket” is closed before installing the
swim-trainer unit onto the mounting bracket assembly
(see fi gure 5.4)
.
5.2
10
11
8
SETUP INSTRUCTIONS (continued)
X X
5.3
X
1
2
5.1
XX
5.4
4
22
MIN
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 11
6.3
5
1
• Adjust the nut on the swimming machine
until the support plate is against the pool
wall and the swim-trainer unit is perfectly
horizontal
(see figure 5.5).
C: For In Ground Pools
1. Mounting Bracket Assembly (see
figures 6.1 to 6.3):
• Make sure the top surface of the pool
edge is stable, flat and level.
• Pay attention to the electrical, gas and
water lines when drilling the holes.
• All screws provided must be used.
• Drill two holes on the center of the
short-end side of the pool edge where the
mounting bracket will be installed. Insert
the in ground pool screws
(5)
into the
holes, and make sure the screws are
fully inserted
(see figures 6.1 to 6.2)
.
• Place the in ground pool mounting
bracket
(1)
over the installed screws
(5)
and tighten the nuts securely
(see figure 6.3)
.
SETUP INSTRUCTIONS (continued)
5.5
Water level
90
Degree
Ajustable nut
for adjusting the
distance
215mm(8.5”)
332mm(13”)
6.1
5
100~250mm(4~10”)
50mm(2”)
Ø10mm(0.4”)
MAX 40mm(1
.5”)
6.2
Water level
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 12
2. Swim-Trainer Unit Assembly (see fi gures 6.4 to 6.5).
• Be sure the swim-trainer unit “support bracket” is closed before installing the
swim-trainer unit onto the mounting bracket assembly
(see fi gure 6.4)
.
• Adjust the support nuts on the
swim-trainer unit until the swim-trainer
unit is horizontal with the water surface
(see figure 6.5)
.
Swim-Trainer Unit height adjustment
and display panel assembly, for all
types of pools
1.
The swim-trainer unit must be submerged
in water with only the top surface of the
housing exposed. Lock the nuts in place
after the height of the swim-trainer unit
is adjusted
(see figure 7)
.
2.
Attach the display panel
(16)
onto the
swim-trainer unit mounting bracket.
Connect the display cable plug to the
display panel receptacle. Tighten up the
display cable collar nut
(see figure 8)
by
hand. Make sure the display cable plug is
firmly attached and the collar nut is
securely tightened.
3.
Place the flat magnetic end of the
emergency stop lanyard
(19)
on the
swim-trainer unit
(32)
housing in order
to activate the unit
(see figure 8)
.
IMPORTANT:
During an emergency
situation, pull the emergency stop
lanyard handle, the unit will stop and
the display panel will go blank.
8
16
32
19
SETUP INSTRUCTIONS (continued)
6.5
Water level
7
Water level
X X
6.4
4
22
Max
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 13
Connecting the swim-trainer unit to the
transformer (see fi gures 9.1 to 9.2)
.
1.
Be sure the transformer
(2)
switch is
OFF, connect the transformer cable to
a grounded electrical outlet.
2.
Transformer must be fi xed to a solid,
level ground or base. Connect the
swim-trainer unit power cable plug into
the transformer power receptacle. Be
sure the plug collar is securely tightened
(see fi gure 9.1 to 9.2)
.
3.
Position the transformer 2m or more away
from the pool, so as to prevent children
from climbing on it and accessing the pool.
4.
Test the GFCI or RCD before use:
a) Press the “RESET” button. The
indicator on the RCD should be “ON”.
b) Press the “TEST” button. The indicator
on the RCD should be “OFF”.
c) Press the “RESET” button again to
start using the product.
d) Do not use the product if the test
failed. Contact a qualifi ed electrician to
inspect the electrical outlet socket.
5.
Turn the transformer switch ON.
NOTE:
To reactivate the swim-trainer unit after the emergency stop lanyard is pulled,
replace the emergency stop lanyard back into the swim-trainer unit, unplugged and
re-plugged the power cable from the transformer.
SETUP INSTRUCTIONS (continued)
425mm
6.4mm
9.2
9.1
ON/OFF Switch
Fuse Box
Power
receptacle
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 14
Display Panel Function
Zone #1 Function
A: On/Off Button
B: Speed Increase Button
C: Speed Decrease Button
D: Speed Setting Display
OPERATION INSTRUCTIONS
Antenna
Zone #1 Function
Zone #2 Function
ABC
D
I
EFGH
A: On/Off Button:
Once the swim-trainer unit is connected to the
transformer and the transformer turned ON, use this button to active the system.
The LED panel will show the default speed setting once activated.
B/C: Speed Adjustment Buttons:
Press to increase or decrease the speed setting.
NOTE:
The default speed is 3; speed adjustment ranges from 1 to 8.
D: Speed Setting Display:
Once activated the system displays the swim-trainer
unit speed automatically.
Zone #2 Function
H:
Toggle button between
Timer
“ ”
and
Counter
“ ”
Mode.
Timer Mode:
Allows the user to program the duration of the
swimming time (in minutes). Once the time is reached,
the machine will stop. Maximum setting is 90 minutes.
E:
Timer Increase Button
F:
Timer Decrease
G:
Timer Review/Confi rm Button
I:
Timer LED Display
Counter Mode:
Tracks the duration (in minutes) or calorie
(in kcal) or distance (in kilometer or mile) of the swim.
E/F:
Counter unit toggle button (minute / kcal
/ kilometer / mile)
G:
Counter On/Pause Button. Press for 2 sec
to reset the counter.
I:
Counter LED Display
EFG
I
H
EFG
I
H
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 15
Remote Control:
1.
Remove the insulation material under the battery.
Battery type (included): CR2032. Be sure the battery cover
is securely attached.
2.
Place the remote control in a reachable location (on top
of the horizontal pool frame). The back of the remote
control is magnetized”.
Note:
In an emergency situation, simply press the “emergency cut off” button to shut off the
system completely, the indicator light inside the remote control housing will light up and the
display panel will indicate “C”.
• Check and make sure all screws are securely tightened on a regular basis.
• When not in use, fold the display panel down and cover the pool with a pool cover.
Long Term Storage and Winterization
You must disassemble and store the product indoors when the temperature drops below 0
O
C /
32OF or when the appliance will not be used for a long period of time.
IMPORTANT:
Close the support bracket before
disassembling and removing the swim-trainer unit from
the mounting bracket assembly (Only for Intex
Rectangular Frame Pools).
1. Turn off the transformer and unplug the power cable
from the electrical outlet.
2. Disconnect the swim-trainer unit power cable from the
transformer.
3. Remove the swim-trainer unit and the
mounting bracket assembly from the pool by reversing
the installation instructions.
4. Clean the swim-trainer unit with a garden hose, and air-dry thoroughly under the sun.
5. Store the unit and accessories in a dry place. The storage’s temperature should be between
0
O
C / 32OF and 40OC (104OF). The original packing can be used for storage.
OPERATION INSTRUCTIONS (continued)
Emergency Cut off Button
MAINTENANCE
4
22
10
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 16
INTERNAL PARTS REPLACEMENTS
Tools required: one Philip screwdriver, one flat screwdriver and one small adjustable
wrench.
A:
Propeller and motor disassembly
1
3
2
31
5 6
27
MAX
4
22
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 17
INTERNAL PARTS REPLACEMENTS
(continued)
B:
Swim-trainer unit bracket and circuitry box disassembly
22
7
16
8
20
24
33
22
9 10
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 18
TROUBLESHOOTING GUIDE
LED PANEL
CODE
PROBLEM SOLUTION
E
●
The maximum operating time
(90 minutes) has fi nished under the
same set mode.
● It's normal. Turn off and unplug the unit.
Then plug the RCD/GFCI back and
restart all back again.
C
● Low water level.
● swim-trainer unit is not fully immersed
in the water.
●
Remote control is in an emergency cut
off situation.
●
Household voltage is too low.
●
Fill the pool with water up to correct water
level (see pool owner‘s manual).
● Make sure the device is under the water.
●
It‘s normal. Turn off the transformer for 1
minute, then plug in.
●
Check the voltage is within the range
stated on the device housing.
H
●
Household voltage is too heigh.
●
Clogged motor impeller
●
Check the voltage is within the range
stated on the device housing
●
Turn off the power, check and clean the
motor impeller
L
●
Water temperature is around
35°C (95°F)
●
Turn off and unplug the unit. When the
water has cooled down, plug the RCD/
GFCI back and restart all over again.
P
●
Operating time is too long
●
Water temperature is around
35°C (95°F)
●
Turn off and unplug the unit, after 30
minutes later plug the RCD/GFCI back
and restart all over again.
●
Turn off and unplug the unit. When the
water has cooled down, plug the RCD/
GFCI back and restart all over again.
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 19
TROUBLESHOOTING GUIDE (continued)
PROBLEM CAUSE SOLUTION
Mounting bracket
can‘t be assembled
with the in ground
pool
●
The ground is not concrete, i.e., it is
asphalt, lawn or earth.
●
The screws are not fully inserted in the
drill holes.
●
Assembly the mounting bracket
on the cement ground.
●
Check and tighten the screws
securely.
swim-trainer unit is
not horizontal with
the water surface
● The support bracket is not opened.
●
Adjust the support nuts on the
swim-trainer unit.
●
Open and adjust the support
bracket. See “Setup Instructions”.
●
Adjust the support nuts on the
swim-trainer unit.
No output from the
transformer
●
swim-trainer unit will hibernate if no
operating more than 1 hour.
●
The transformer fuse broken.
●
Motor too hot and overload protection is
shut off.
●
Turn off the transformer, waiting 2
minutes then turn on agin.
●
Replace the transformer fuse.
●
Let the motor cool down and
restart again.
No LED display
●
The transformer is unplugged or off.
●
The transformer is not connected with
swim-trainer unit.
●
Display panel cord is loose.
●
Display panel failure.
●
Emergency stop lanyard is put wrong
place.
●
Ensure the transformer is plugged
and switched on.
●
Connect the transformer with
swim-trainer unit.
●
Ensure that the display cord is
plugged fi rmly into the cell housing
receptacle.
●
Contact Intex Service Center.
●
Put the emergency stop lanyard
on correct place. See “Setup
Instructions”.
Abnormal display /
buttons not working
●
Display panel cord is loose.
●
Display panel failure.
●
Ensure the display cable is
plugged fi rmly into the display
panel receptacle
.
●
Contact Intex Service Center.
Too noisy / Jet water
is weak or shaking
●
Swim-trainer unit is not fully immersed in
the water.
● The motor impeller is broken.
●
swim-trainer unit components
not securely connected or in place.
●
Make sure the device is under
the water.
●
Turn off and replace the motor
impeller.
●
Check all components, especially
the support bracket. See “Setup
Instructions”.
Remote Control out
of control
●
The battery is on low power.
● Replace the remote control
battery.
See “Operating Installations”.
(303PO) MODEL SM24101 SWIMMING MACHINE ENGLISH 7.5” X 10.3” PANTONE 295U 02/21/2017
303
PO
SAVE THESE INSTRUCTIONS
English
Page 20
PARTS LIST
LIMITED WARRANTY
Your Hydro Flow™ Swim Trainer has been manufactured using the highest quality materials
and workmanship. All Intex products have been inspected and found free of defects prior to
leaving the factory. This Limited Warranty applies only to the Hydro Flow™ Swim Trainer and
accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of purchase
will be required and must accompany warranty claims or the Limited Warranty is invalid.
Hydro Flow™ Swim Trainer Warranty – 2 Years
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim. If the Service Center directs you
to return the product, please carefully package the product and send with shipping and
insurance prepaid to the Service Center. Upon receipt of the returned product, the Intex
Service Center will inspect the item and determine the validity of the claim. If the provisions
of this warranty cover the item, the item will be repaired or replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought before
an informal dispute settlement board and unless and until the provisions of these paragraphs
are carried forth, no civil action may be instituted. The methods and procedures of this
settlement board shall be subject to the rules and regulations set forth by the Federal Trade
Commission (F.T.C.). IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS
WARRANTY AND IN NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR
EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR
CONSEQUENTIAL DAMAGES OR LIABILITIES. Some states, or jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This Limited Warranty does not apply if the products are subject to negligence, abnormal use
or operation, accident, improper operation, improper voltage or current contrary to operating
instructions, or to damage by circumstances beyond Intex’s control, including but not limited
to, ordinary wear and tear and damage caused by exposure to fire, flood, freezing, rain, or
other external environmental forces. This Limited Warranty applies only to those parts and
components sold by Intex. The Limited Warranty does not cover unauthorized alterations,
repairs or disassembly by anyone other than Intex Service Center personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN
OR REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
Loading...