Intex AP619RL Owner's Manual
73-1
(73-1) AP619RL REMOTE CONTROL BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 07/14/2011
73-1
(
73-1) AP619RL REMOTE CONTROL BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25”
07/14/2011
READ AND SAVE THESE INSTRUCTIONS
Page 1
READ AND SAVE THESE INSTRUCTIONS
Page 2
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
INTEX®OWNER'S MANUAL
Built-in Fast-Fill™ Electric Pump
with Remote Control
Model AP619RL 110 – 120 V~ 60 Hz 1.0 A
073-1**-R0-1207
INFLATION
1. Make sure the "2 in 1" valve is securely closed. See Fig (1).
2. Plug in the AC line cord into an AC electrical outlet. See Fig (2).
3. Open the foam vacuum valve on the corner of the sleeping surface of bed. See Fig (3).
FIG (2)
110 – 120 V
220 – 240 V
√
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
To reduce the risk of burns, fire, electric shock, or injury to persons:
• NEVER PLACE AN INFANT TO SLEEP ON AIR MATTRESSES.
• Never introduce any flammable substance into the inflatable airbed, such as aerosol tire repair products, as it
may ignite or explode.
• For indoor household use only.
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disable persons.
• Use this furnishing only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacturer.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
• This is not a toy. Children must not be left unattended when using the airbed.
• Keep the storage bag away from babies and children. The storage bag is not a toy.When not in use, fold the
bag and put it away out of the reach of children.
• Do not walk, stand on or jump on or use the airbed as a trampoline.
• Do not use on or near water. This is not a raft.
• Do not set up bed near stairs, doors, sharp edges or breakable objects. Provide adequate space between
bed and objects to avoid entrapment.
• Make sure the area is flat, smooth, free of sharp objects that could puncture the bed and keep away from
ledges.
• Keep pets away from the airbed. Pets may puncture the surface of the bed.
• Avoid sleeping on the edge of the airbed. Edges produce less support than the middle
of the bed.
• Do not operate air pump for more than 10 minutes at a time. Let pump cool at least 10
minutes between uses.
• Unplug electrical power cord when not in use. To disconnect, turn all controls to the off position, then remove
plug from outlet.
• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and
the like. Never drop or insert object into any opening.
• Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and/or
repair.
• If the AC supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to
avoid a hazard.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped
over. Keep the cord away from heated surfaces.
FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID SUFFOCATION,
PROPERTY DAMAGE, ELECTRIC SHOCK, BURNS OR OTHER INJURY.
WARNING
•
To reduce the risk of electric shock or injury, use indoors only, do not expose to rain. Store indoors.
CAUTION
5
4
3
2
1
6
7
9
8
10
FIG (1)
FIG (3)
•
To reduce the risk of electric shock: Always unplug this furnishing from the electrical outlet before cleaning.
DANGER
SERVICING OF A DOUBLE-INSULATED PRODUCT:
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding
means is provided on a double-insulated product, nor should a means for grounding be added to the
product. Servicing of a double-insulated product requires extreme care and knowledge of the system,
and should be done only by qualified service personnel. Replacement parts for a double-insulated
product must be identical to those parts in the product.
A double-insulated product is marked with the words "DOUBLE INSULATION" or "DOUBLE INSULATED" and with the symbol .
Part Descriptions:
1. AIRBED
2. "2 IN 1" VALVE
3. HANDLE
4. STORAGE POCKET
5. FOAM VACUUM VALVE
6. INFLATION SWITCH
7. ADJUSTING SWITCH
8. REMOTE CONTROL
9. AC LINE CORD
10. AIR PASSAGE
PARTS REFERENCE
INSTRUCTIONS
General
• This appliance has a polarized plug (one blade is wider than the other).
This plug will fit in a
polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug.
If it still
does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
• No air pump maintenance is required.
•
For cleaning use only mild soapy solution. Do not use any chemicals.
•
In case of repairs, use only common PVC repair glue and patches.
73-1
(73-1) AP619RL REMOTE CONTROL BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 07/14/2011
73-1
(
73-1) AP619RL REMOTE CONTROL BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25”
07/14/2011
READ AND SAVE THESE INSTRUCTIONS
Page 3
READ AND SAVE THESE INSTRUCTIONS
Page 4
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten.
Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarksused in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas
utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an
Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801
• Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., P.O.Box nr. 1075 – 4700 BB Roosendaal – The Netherlands Consumer Service 1-800-234-6839
6. Pat on the bed surface to adjust the foam.
NOTE: Leave the vacuum valve open to allow
the foam to re-shape itself, this may take up to
five minutes before initial use.
7. Close the foam vacuum valve.See Fig (6).
8. Lie down on the airbed to test the firmness.
9. If the sleeping surface is too hard, adjust the firmness by pressing and holding the
adjusting switch. Air will exit through the air passage. See Fig (7). Release the adjusting
switch when the desired firmness is achieved. If the airbed becomes too soft repeat
steps #4, #5, #8 and #9 as necessary.
IMPORTANT: Do not hold the adjusting switch for more than 30 continuous seconds, as
overheating will occur. Wait 10 minutes before using again to allow cooling.
10. Disconnect the AC line cord from the wall socket; place the line cord and the remote
control in the storage pocket. See Fig (8).
Proper inflation of the airbed.
The ambient temperatures of air have an effect on the airbed internal pressure. At low
ambient temperature the air will contract within the airbed and the airbed will feel softer:
add air as necessary. At high ambient temperature the air within the airbed will expand
significantly and the airbed will become hard and may burst: release air to avoid damage
to the airbed or to soften the feel. Do not expose the airbed to extreme temperatures (hot
or cold).
Air inside of bed may expand and contract with varying temperature leading to reduce
pressure inside of the bed. If this occurs, simply add more air using the pump to achieve
desired firmness. If puncture occurs, please refer to instruction. Repair kit/patch is
enclosed.
Stretching is a natural characteristic of new vinyl. During initial use, the airbed may
become soft and require additional inflation to maintain desired firmness. This is normal for
the first few days of use.
Dimensions shown are approximate and will vary due to the vinyl temperature and the air
temperature.
In no event shall Intex, their authorized agents or employees be liable for damages
(such as pin holes) to the airbed caused by negligence, ordinary wear and tear,
abuse and carelessness, or external forces.
IMPORTANT NOTE
Inflate only with a low pressure inflator. Do not over inflate. Fill with cold air only.
IMPORTANT
STORAGE
1. Deflate the airbed following the "DEFLATION" instructions.
2. Make sure the airbed is clean and dry.
3. Lay bed flat with sleeping surface facing upwards and follow the folding steps on Figs (12 - 16).
Fold the airbed loosely and avoid sharp bends, corners and creases which can damage the airbed.
4. Place the airbed inside the storage bag and store in a dry, cool storage location.
FIG (6)
DEFLATION
1. Unscrew the exhaust valve cap from the "2 in 1" valve.
See Fig (9).
2. Open the foam vacuum valve on the corner of
the sleeping surface of bed. See Fig (3).
3. Begin rolling the airbed from the foot of the airbed
towards the head of the airbed where the pump is
located, let the airbed stand with the valve open for a
while to let any remaining air to flow out of the valve.
See Fig (10). Make sure to screw the exhaust valve
cap back into the "2 in 1" valve. See Fig (1).
4. Place the line cord and the remote control in the
storage pocket.
FIG (9)
FIG (10)
FIG (7)
FIG (8)
INFLATION OPTION
1. If electrical power is not available then a conventional
foot or manually operated air pump can be connected
to the optional "2 in 1" valve for inflation.
2. Pull the valve cap out from the "2 in 1" valve and insert the
air hose of a conventional foot or manually operated air
pump. See Fig (11).
3. Start inflating with foot or hand pump, inflate to desired
firmness.
FIG (11)
Fa
s
t
-
F
i
l
l
E
l
e
c
t
r
i
c
A
i
r
P
u
m
p
©
2
0
0
5
®
T
M
I
n
t
x
R
a
t
i
n
C
p
L
n
g
B
a
h
C
A
9
0
8
01
14
4
0
U
S
A
®
™
T
a
d
m
a
k
u
d
i
n
m
u
n
t
i
f
t
h
w
l
d
b
y
I
n
t
x
T
a
d
i
n
g
L
t
d
u
n
d
l
i
n
f
m
I
n
t
x
M
a
k
t
i
n
g
L
t
d
M
a
d
i
n
C
h
i
n
a
/
F
a
b
i
q
u
é
n
C
h
i
n
/
H
h
n
C
h
i
n
a
I
N
T
E
X
®
F
a
s
t
-
F
i
l
l
E
l
e
c
t
r
i
c
A
i
r
P
u
m
p
©
2
0
0
5
®
T
M
I
t
x
R
t
i
C
L
g
B
h
C
A
9
0
8
0
1
1
4
4
0
U
S
A
®
™
T
d
m
k
u
d
i
m
u
t
i
f
t
h
w
l
d
b
y
I
t
x
T
d
i
g
L
t
d
u
d
l
i
f
m
I
t
x
M
k
t
i
g
L
t
d
M
d
i
C
h
i
/
F
b
i
qu
é
C
h
i
/
H
h
C
h
i
IN
T
E
X
®
I
N
T
E
X
®
©
2
0
0
5
®
T
M
I
t
x
R
t
i
C
L
g
B
h
C
A
9
0
8
0
1
1
4
4
0
U
S
A
®
™
T
d
m
k
u
d
i
m
u
t
i
f
t
h
w
l
d
b
y
I
t
x
T
d
i
g
L
t
d
u
d
l
i
f
m
I
t
x
M
k
t
i
g
L
t
d
M
d
i
C
h
i
/
F
b
i
qu
é
C
h
i
/
H
h
C
h
i
F
a
s
t
-
F
i
l
l
E
l
e
c
t
r
i
c
A
i
r
P
u
m
p
©2005 ®TM Intex Recreation CorpLong Beach,
CA90801-1440 USA
®™ Trademarksused in some countriesof
the world by Intex Trading Ltd.,underlicense
f
rom Intex Marketing Ltd.
Made inChina/ Fabriqué en Chine
/Hecho en China
INTEX
®
Fast-Fill™
Electric Air Pump
©
2005 ®TM Intex RecreationCorp., Long Beach,
C
A90801-1440 USA
®
™Trademarks used insome countries
o
fthe world byIntexTradingLtd., under license
f
rom Intex Marketing Ltd.
Made inChina/ Fabriquéen Chine
/Hechoen China
INTEX
®
F
ast-Fill™
Electric Air Pump
F
FIG (12)
FIG (13)
FIG (14)
FIG (15)
FIG (16)
4. Press "I" to switch ON. See Fig (4).
5. When the airbed is fully inflated to the desired firmness, press "O" to switch OFF. See
Fig (5).
F
IG (4) FIG (5)
Loading...