Page 1
Internet Camera
Quick Installation Guide
Rev. 01 (March, 2005)
Made in Taiwan
1
Page 2
Page 3
1
Before You Begin…
System Requirement:
●
10 Base-T Ethernet or 100 Base-TX Fast Ethernet
●
CD-ROM drive
●
CPU: Intel Celeron 1.1GHz or above
●
Memory: 128MB or above
●
VGA resolution: 800x600 or above
Package Contents:
●
One Internet Camera
●
One External Antenna (for wireless model)
●
One Power Adapter
●
One RJ-45 Ethernet Cable
●
One Camera Stand
●
This
Quick Installation Guide
●
One Installation CD-ROM
Note: If any item contained is damaged or missing, please contact
your local dealer immediately.
1
Page 4
n
2
Hardware Installation
Attaching the Camera Stand
The Internet Camera comes with a
camera stand, which has a swivel ball
screw head that can be attached to the
camera’s screw hole on the top/bottom
panel. Attach the camera stand to the
camera and station it for your application.
Attaching the Antenna (for wireless model)
From the rear panel of the camera, screw
the provided external Antenna into the
antenna connector.
Connecting the Ethernet Cable
Connect an Ethernet cable to the network
cable connector located on the camera’s
rear panel, and then connect it to the
network.
Connecting the Power Supply
Connect the external power supply to the
DC power input connector located on the
camera’s rear panel, and then connect it
to your wall outlet.
Tip: You can confirm the power source is supplied from the Power LED o
the camera.
2
Page 5
3
Running the Setup Wizard
The Setup Wizard is a convenient tool that will guide you through the
installation of your camera easily and quickly. After connecting the
camera to your computer, you can install the Setup Wizard and
complete the configuration now.
1. Insert the Installation
CD-ROM into your CD-ROM
drive.
Click Setup Wizard.
2. Click Next.
3. Click Yes.
3
Page 6
4. Click Next.
5. Click Finish.
To run the Setup Wizard,
click Start -> Programs
-> Setup Wizard.
4
Page 7
4
Using the Setup Wizard
When you launch the Setup Wizard, the main window will appear as
shown, and the connected camera will be displayed in the list.
Control buttons
The connected camera list
The components on the Setup Wizard:
Click Wizard to begin configuring the selected
camera.
Click Research allows you to search the connected
camera again.
Click Link to launch the web browser and view the
images.
Click About to show the general information of the
selected camera.
Click Exit to close the Setup Wizard.
5
Page 8
Changing the Admin ID and Password
By default settings, the Admin ID and Password are blank. For
security purpose, you are recommended to change the Admin ID and
Password immediately.
Click Wizard. The dialog window
appears as shown, asking you to
enter the Admin ID and Password.
If required, select the Change
options and enter the new Admin ID
and Password.
Enter the default ID and Password.
Enter admin in both boxes and then
click Next.
The settings of IP Address, Subnet
Mask and Default Gateway must
correspond with your camera and
networking settings. Please check
with your network administrator for
correct settings.
Click Next.
This step is for wireless model only.
If you want to use wireless function,
select the Enable option. Then, you
have to set up the related settings in
the following fields of the screen,
including Connection Mode,
Network Name (SSID), Wireless
Channel, Security Mode, and
Authentication.
If you enable the Security Mode,
you have to set up the configuration
in the following window.
For wireless model
6
Page 9
This window displays the settings you
set up. For any change, click Back
to modify your settings. Otherwise,
click Restart to save and apply the
settings.
The configuration is completed, and
you will return to the main window.
Click Link to launch the web browser
and view the images.
7
Page 10
5
Tips
Software Information
Click About to show the
general information of the
selected camera.
Click OK to return to the
main window.
Technical Support
For more information, please refer to the User’s Guide located on the
CD-ROM.
8
Loading...