
查询ST300C..L SERIES供应商
PHASE CONTROL THYRISTORS Hockey Puk Version
Bulletin I25193 rev. B 04/00
ST300C..L SERIES
Features
Center amplifying gate
Metal case with ceramic insulator
International standard case TO-200AC (B-PUK)
Typical Applications
DC motor controls
Controlled DC power supplies
AC controllers
Major Ratings and Characteristics
Parameters ST300C..L Units
I
T(AV)
I
T(RMS)
I
TSM
@ T
hs
@ T
hs
@ 50Hz 8000 A
@ 60Hz 8380 A
560 A
55 °C
1115 A
25 °C
560A
case style TO-200AC (B-PUK)
I2t@
V
DRM/VRRM
t
q
T
J
50Hz 320 KA2s
@ 60Hz 292 KA
typical 100 µs
www.irf.com
400 to 2000 V
- 40 to 125 °C
2
s
1

ST300C..L Series
Bulletin I25193 rev. B 04/00
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage V
DRM/VRRM
Type number Code peak and off-state voltage repetitive peak voltage @ T
04 400 500
08 800 900
ST300C..L 50
12 1200 1300
16 1600 1700
18 1800 1900
20 2000 2100
On-state Conduction
Parameter ST300C..L Units Conditions
I
Max. average on-state current 560 (275) A 180° conduction, half sine wave
T(AV)
@ Heatsink temperature 55 (75) °C double side (single side) cooled
I
Max. RMS on-state current 1115 DC @ 25°C heatsink temperature double side cooled
T(RMS)
Max. peak, one-cycle 8000 t = 10ms No voltage
I
TSM
non-repetitive surge current 8380 A t = 8.3ms reapplied
2
t Maximum I2t for fusing 320 t = 10ms No voltage Initial TJ = TJ max.
I
2
I
√t Maximum I2√t for fusing 3200 KA2√s t = 0.1 to 10ms, no voltage reapplied
Low level value of threshold
V
T(TO)1
voltage
High level value of threshold
V
T(TO)2
voltage
r
Low level value of on-state
t1
slope resistance
High level value of on-state
r
t2
slope resistance
V
Max. on-state voltage 2.18 V Ipk= 1635A, TJ = TJ max, tp = 10ms sine pulse
TM
I
Maximum holding current 600
H
I
Typical latching current 1000
L
, max. repetitive V
, maximum non- I
RSM
DRM/IRRM
VVmA
6730 t = 10ms 100% V
7040 t = 8.3ms reapplied Sinusoidal half wave,
292 t = 8.3ms reapplied
226 t = 10ms 100% V
KA2s
207 t = 8.3ms reapplied
0.97 (16.7% x π x I
V
0.98 (I > π x I
T(AV)
0.74 (16.7% x π x I
mΩ
0.73 (I > π x I
mA T
T(AV)
= 25°C, anode supply 12V resistive load
J
RRM
RRM
< I < π x I
T(AV)
),TJ = TJ max.
< I < π x I
T(AV)
),TJ = TJ max.
), TJ = TJ max.
T(AV)
), TJ = TJ max.
T(AV)
max.
= TJ max
J
2
www.irf.com

ST300C..L Series
Bulletin I25193 rev. B 04/00
Switching
Parameter ST300C..L Units Conditions
di/dt Max. non-repetitive rate of rise Gate drive 20V, 20Ω, tr ≤ 1µs
of turned-on current T
t
Typical delay time 1.0
d
t
Typical turn-off time 100
q
Blocking
Parameter ST300C..L Units Conditions
dv/dt Maximum critical rate of rise of
off-state voltage
Max. peak reverse and off-state
I
RRM
leakage current
I
DRM
1000 A/µs
= TJ max, anode voltage ≤ 80% V
J
Gate current 1A, dig/dt = 1A/µs
= 0.67% V
V
d
µs
= 550A, TJ = TJ max, di/dt = 40A/µs, VR = 50V
I
TM
dv/dt
DRM, TJ
= 20V/µs, Gate 0V 100Ω, tp = 500µs
= 25°C
500 V/µsTJ = TJ max, linear to 80% rated V
50 mA TJ = TJ max, rated V
DRM/VRRM
DRM
DRM
applied
Triggering
Parameter ST300C..L Units Conditions
PGMMaximum peak gate power 10.0 TJ = TJ max, tp ≤ 5ms
P
Maximum average gate power 2.0 TJ = TJ max, f = 50Hz, d% = 50
G(AV)
Max. peak positive gate current 3.0 A TJ = TJ max, tp ≤ 5ms
I
GM
+V
Maximum peak positive
GM
gate voltage
Maximum peak negative
-V
GM
gate voltage
20
5.0
TYP. MAX.
I
DC gate current required
GT
to trigger
200 -
100 200
50 -
V
DC gate voltage required
GT
to trigger
I
DC gate current not to trigger 10.0 mA
GD
2.5 -
1.8 3.0
1.1 -
VGDDC gate voltage not to trigger 0.25 V
W
= TJ max, tp ≤ 5ms
VT
J
T
= - 40°C
J
= 25°C
mA T
J
TJ = 125°C
TJ = - 40°C
VTJ = 25°C
T
= 125°C
J
= TJ max
T
J
Max. required gate trigger/ current/ voltage are the lowest value
which will trigger all units 12V
anode-to-cathode applied
Max. gate current/voltage not to
trigger is the max. value which
will not trigger any unit with rated
V
anode-to-cathode applied
DRM
www.irf.com
3

ST300C..L Series
Bulletin I25193 rev. B 04/00
Thermal and Mechanical Specification
Parameter ST300C..L Units Conditions
TJMax. operating temperature range -4 0 to 125
Max. storage temperature range - 40 to 150
T
stg
R
Max. thermal resistance, 0.11 DC operation single side cooled
thJ-hs
junction to heatsink 0.05 DC operation double side cooled
Max. thermal resistance, 0.011 DC operation single side cooled
R
thC-hs
case to heatsink 0.006 DC operation double side cooled
F Mounting force, ± 10% 9800 N
(1000) (Kg)
wt Approximate weight 250 g
Case style TO - 200AC (B-PUK) See Outline Table
∆R
Conduction
thJ-hs
(The following table shows the increment of thermal resistence R
Conduction angle Units Conditions
180° 0.012 0.010 0.008 0.008 T
120° 0.014 0.015 0.014 0.014
90° 0.018 0.018 0.019 0.019 K/W
60° 0.026 0.027 0.027 0.028
30° 0.045 0.046 0.046 0.046
Sinusoidal conduction Rectangular conduction
Single Side Double Side Single Side Double Side
°C
K/W
K/W
when devices operate at different conduction angles than DC)
thJ-hs
J
= TJ max.
Ordering Information Table
Device Code
1 - Thyristor
2 - Essential part number
3 - 0 = Converter grade
4 - C = Ceramic Puk
5 - Voltage code: Code x 100 = V
6 - L = Puk Case TO-200AC (B-PUK)
7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads)
1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads)
2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads)
3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8 - Critical dv/dt: None = 500V/µsec (Standard value)
4
ST 30 0 C 20 L 1
3 4
(See Voltage Rating Table)
RRM
L = 1000V/µsec (Special selection)
51 2
768
www.irf.com

Outline Table
27 (1.06) MAX.
0.7 (0.03) MIN.
0.7 (0.03) MIN.
34 (1.34) DIA. MAX.
TWO PLACES
53 (2.09) DIA. MAX.
6.2 (0.24) MIN.
PIN RECEPTACLE
AMP. 60598-1
ST300C..L Series
Bulletin I25193 rev. B 04/00
4.7 (0.18)
5 8. 5 (2 .3 ) D IA . M AX .
36.5 (1.44)
2 HOLES DIA. 3.5 (0.14) x
2.5 (0.1) DEEP
CREPAGE DISTANCE 36.33 (1.430) MIN.
STRIKE DISTANCE 17.43 (0.686) MIN.
130
120
110
100
ST300C..L Series
(Single Side Cooled)
R (DC) = 0.11 K/W
thJ-hs
130
120
110
100
90
60˚
90˚
Conduction Angle
120˚
180˚
80
70
60
50
30˚
40
30
0 100 200 300 400 500
Maximum Allowable Heatsink Temperature (°C)
Maximum Allowable Heatsink Temperature (°C)
Average On-state Current (A)
Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics
20°± 5°
Case Style TO-200AC (B-PUK)
All dimensions in millimeters (inches)
Quote between upper and lower
pole pieces has to be considered
after application of Mounting Force
(see Thermal and Mechanical
Specification)
ST300C..L Series
(Single Side Cooled)
R (DC) = 0.11 K/W
thJ-hs
90
80
70
60
50
40
30˚
60˚
90˚
30
20
0 100 200 300 400 500 600 700
Average On-state Current (A)
Conduction Period
120˚
180˚
DC
www.irf.com
5

ST300C..L Series
Bulletin I25193 rev. B 04/00
130
120
110
ST300C..L Series
(Double Side Cooled)
R (DC) = 0.05 K/W
thJ-hs
100
90
80
Conduction Angle
70
60
50
40
30
20
Maximum Allowable Heatsink Temperature (°C)
1600
1400
1200
1000
30˚
60˚
90˚
120˚
180˚
0 200 400 600 800
Average On-state Current (A)
Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics
180˚
120˚
90˚
60˚
30˚
RMS Limit
800
600
400
200
0
Maximum Average On-state Power Loss (W)
0 100 200 300 400 500 600 700
Average On-state Current (A)
Fig. 5- On-state Power Loss Characteristics
Conduction Angle
ST300C..L Series
T = 125˚C
J
130
120
110
ST300C..L Series
(Double Side Cooled)
R (DC) = 0.05 K/W
thJ-hs
100
90
80
Conduction Period
70
30˚
60
50
40
30
20
0 200 400 600 800 1000 1200
Maximum Allowable Heatsink Temperature (°C)
1800
1600
1400
1200
1000
60˚
90˚
120˚
Average On-state Current (A)
DC
180˚
120˚
90˚
60˚
30˚
180˚
DC
RMS Limit
800
600
400
200
0
Maximum Average On-state Power Loss (W)
0 200 400 600 800 1000 1200
Average On-state Current (A)
Fig. 6- On-state Power Loss Characteristics
Conduction Period
ST300C..L Series
T = 125˚C
J
7500
At Any Rated Load Condition And With
7000
6500
6000
Rated Vrrm Applied Following Surge.
Initial Tj = 125˚C
@ 60 Hz 0.0083 s
@ 50 Hz 0.0100 s
5500
5000
4500
4000
ST300C..L Series
3500
Peak Half Sine Wave On-state Current (A)
3000
1 10 100
Number Of Equal Amplitude Half Cycle Current Pulses (N)
Fig. 7 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
6
8000
Maximum Non Repetitive Surge Current
7500
7000
6500
6000
Versus Pulse Train Duration. Control
Of Conduction May Not Be Maintained.
Initial Tj = 125˚C
No Voltage Reapplied
Rated Vrrm Reapplied
5500
5000
4500
4000
ST300C..L Series
3500
3000
Peak Half Sine Wave On-state Current (A)
0.01 0.1 1
Fig. 8 - Maximum Non-Repetitive Surge Current
Pulse Train Duration (s)
Single and Double Side Cooled
www.irf.com

10000
0.001
0.01
0.1
1
0.001 0.01 0.1 1 10
Steady State Value
R = 0.11 K/W
(Single Side Cooled)
R = 0.05 K/W
(Double Side Cooled)
(DC Operation)
thJ-hs
thJ-hs
ST300C..L Series
1000
T = 25˚C
J
T = 125˚C
J
ST300C..L Series
Bulletin I25193 rev. B 03/00
Instantaneous On-state Current (A)
ST300C..L Series
100
0123456789
Instantaneous On-state Voltage (V)
Fig. 9 - On-state Voltage Drop Characteristics
100
Rectangular gate pulse
a) Recommended load line for
(K/W)
rated di/dt : 20V, 10ohms; tr<=1 µs
thJ-hs
b) Recommended load line for
<=30% rated di/dt : 10V, 10ohms
10
tr<=1 µs
(b)
Tj=-40 ˚C
Tj=25 ˚ C
Tj=125 ˚ C
(1) PGM = 10W, tp = 4ms
(2) PGM = 20W, tp = 2ms
(3) PGM = 40W, tp = 1ms
(4) PGM = 60W, tp = 0.66ms
(a)
1
(1)
(2) (3)
VGD
IGD
Transient Thermal Impedance Z
0.1
0.001 0.01 0.1 1 10 100
Device: ST300C..L Series
Frequency Limited by PG(AV)
Square Wave Pulse Duration (s)
Fig. 10 - Thermal Impedance Z
Characteristics
thJ-hs
(4)
Instantaneous Gate Voltage (V)
Instantaneous Gate Current (A)
Fig. 11 - Gate Characteristics
www.irf.com
7