International Rectifier IRFPC50LC Datasheet
HEXFET® Power MOSFET
Next Data SheetIndex
Previous Datasheet
To Order
Ultra Low Gate Charge
Reduced Gate Drive Requirement
Enhanced 30V Vgs Rating
Reduced C
Isolated Central Mounting Hole
Dynamic dv/dt Rated
Repetitive Avalanche Rated
Description
This new series of Low Charge HEXFET Power MOSFETs achieve significantly
lower gate charge over conventional MOSFETs. Utilizing advanced Hexfet
technology the device improvements allow for reduced gate drive requirements,
faster switching speeds and increased total system savings. These device
improvements combined with the proven ruggedness and reliability of HEXFETs
offer the designer a new standard in power transistors for switching applications.
The TO-247 package is preferred for commercial-industrial applications where
higher power levels preclude the use of TO-220 devices. The TO-247 is similar
but superior to the earlier TO-218 package because of its isolated mounting hole.
iss
, C
oss
, C
rss
PD - 9.1233
IRFPC50LC
V
= 600V
DSS
R
ID = 11A
DS(on)
= 0.60 Ω
Absolute Maximum Ratings
Parameter Max. Units
ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 11
ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 7.3 A
I
DM
PD @TC = 25°C Power Dissipation 190 W
V
GS
E
AS
I
AR
E
AR
dv/dt Peak Diode Recovery dv/dt 3.0 V/ns
T
J
T
STG
Pulsed Drain Current 44
Linear Derating Factor 1.5 W/°C
Gate-to-Source Voltage ±30 V
Single Pulse Avalanche Energy 920 mJ
Avalanche Current 11 A
Repetitive Avalanche Energy 19 mJ
Operating Junction and -55 to + 150
Storage Temperature Range °C
Soldering Temperature, for 10 seconds 300 (1.6mm from case)
Mounting torque, 6-32 or M3 screw. 10 lbf•in (1.1N•m)
Thermal Resistance
Parameter Min. Typ. Max. Units
R
θJC
R
θCS
R
θJA
Junction-to-Case –––– –––– 0.65
Case-to-Sink, Flat, Greased Surface –––– 0.24 –––– °C/W
Junction-to-Ambient –––– –––– 40
Revision 0
IRFPC50LC
Next Data SheetIndex
Previous Datasheet
To Order
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter Min. Typ. Max. Units Conditions
V
(BR)DSS
∆V
(BR)DSS
R
DS(ON)
V
GS(th)
g
fs
I
DSS
I
GSS
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
L
D
L
S
C
iss
C
oss
C
rss
Drain-to-Source Breakdown Voltage 600 ––– ––– V VGS = 0V, ID = 250µA
/∆T
Breakdown Voltage Temp. Coefficient ––– 0.59 ––– V/°C Reference to 25°C, ID = 1mA
J
Static Drain-to-Source On-Resistance ––– ––– 0.60 Ω VGS = 10V, ID = 6.6A
Gate Threshold Voltage 2.0 ––– 4.0 V VDS = VGS, ID = 250µA
Forward Transconductance 7.0 ––– ––– S VDS = 100V , ID = 6.6A
Drain-to-Source Leakage Current
Gate-to-Source Forward Leakage ––– ––– 100 VGS = 20V
Gate-to-Source Reverse Leakage ––– ––– -100 VGS = -20V
––– ––– 25 VDS = 600V , VGS = 0V
––– ––– 250 VDS = 480V, VGS = 0V, TJ = 125°C
µA
nA
Total Gate Charge ––– ––– 84 ID = 11A
Gate-to-Source Charge ––– ––– 18 nC VDS = 360V
Gate-to-Drain ("Miller") Charge ––– ––– 36 VGS = 10V, See Fig. 6 and 13
Turn-On Delay Time ––– 17 ––– VDD = 300V
Rise Time ––– 32 ––– ID = 11A
Turn-Off Delay Time ––– 41 ––– RG = 6.2Ω
ns
Fall Time ––– 26 ––– RD = 30Ω, See Fig. 10
Internal Drain Inductance ––– 5.0 –––
Internal Source Inductance ––– 13 –––
Between lead,
6mm (0.25in.)
nH
from package
and center of die contact
Input Capacitance ––– 2300 ––– VGS = 0V
Output Capacitance ––– 270 ––– pF VDS = 25V
Reverse Transfer Capacitance ––– 28 ––– ƒ = 1.0MHz, See Fig. 5
Source-Drain Ratings and Characteristics
I
S
I
SM
V
SD
t
rr
Q
rr
t
on
Notes:
Repetitive rating; pulse width limited by
max. junction temperature. ( See fig. 11 )
V
= 25V, starting TJ = 25°C, L = 13mH
DD
RG = 25Ω, I
Parameter Min. Typ. Max. Units Conditions
Continuous Source Current MOSFET symbol
(Body Diode) showing the
Pulsed Source Current integral reverse
(Body Diode) p-n junction diode.
––– ––– 11
A
––– ––– 44
Diode Forward Voltage ––– ––– 1.4 V TJ = 25°C, IS = 11A, VGS = 0V
Reverse Recovery Time ––– 590 890 ns TJ = 25°C, IF = 11A
Reverse Recovery Charge ––– 4.5 6.8 µC di/dt = 100A/µs
Forward Turn-On Time
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
I
≤ 11A, di/dt ≤ 100A/µs, V
SD
DD
≤ V
(BR)DSS
,
TJ ≤ 150°C
Pulse width ≤ 300µs; duty cycle ≤ 2%.
= 11A. (See Figure 12)
AS
IRFPC50LC
A
A
A
A
To Order
Next Data SheetIndex
Previous Datasheet
100
VGS
TOP 15V
10V
8.0 V
7.0 V
6.0 V
5.5 V
5.0 V
10
BOTTOM 4.5V
1
0.1
D
I , Drain-to-Source Current (A)
20µs PULSE WIDTH
T = 25°C
0.01
0.01 0.1 1 10 100
V , Drain-to-Source Voltage (V)
DS
C
Fig 1. Typical Output Characteristics,
TC = 25oC
100
4.5V
100
VGS
TOP 15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
10
BOTTOM 4.5V
1
0.1
D
I , Drain-to-Source Current (A)
20µs PULSE WIDTH
T = 150°C
0.01
0.01 0.1 1 10 100
V , Drain-to-Source Voltage (V)
DS
C
Fig 2. Typical Output Characteristics,
TC = 150oC
3.0
I = 11A
D
4.5V
T = 150°C
J
10
1
0.1
D
I , Drain-to-Source Current (A)
0.01
4 5 6 7 8 9 10
Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance
T = 25°C
J
V = 100V
DS
20µs PULSE WIDTH
V , Gate-to-Source Voltage (V)
GS
2.5
2.0
1.5
(Normalized)
1.0
0.5
DS(on)
R , Drain-to-Source On Resistance
0.0
-60 -40 -20 0 20 40 60 80 100 120 140 160
T , Junction Temperature (°C)
J
Vs. Temperature
V = 10V
GS
Loading...