International Power Sources ZCA8CPS12C, ZCA8CPS12CI, ZCA8CPS12CM, ZCA8CPS12CR, ZCA8CPS12I Datasheet

Input

AC Input Voltage • 85-264 VAC
Input Frequency • 47-63 Hz
Power Factor • 0.99
Inrush Current • Limited to 30 A peak
Input Protection • Internal 20 A fuse

Output

Output Voltage • 12, 24 or 48 VDC with 5 VSB

at 250 mA
Output Power • 650-800 W
Output Voltage • ±5% min

Adjustment
Minimum Load • No minimum load for all outputs
Line/Load Regulation • ±2%
Ripple & Noise • 1% pk-pk maximum
Transient Response • 4% max deviation, 300 µs recovery

time for a 25% load change
Temperature • 0.02%/°C

Coefficient
Hold Up Time • 20 ms minimum
Remote Sense • Up to 0.25 V compensation
Overvoltage • Latched shutdown, recycle

Protection input to reset
Overcurrent • Standard with auto recovery

Protection
Overtemperature • Logic high signal for overtemp

Protection conditions
Current Sharing • ±10%

General

Efficiency • 75-85% typical at full load
MTBF • 200,000 hrs per Bellcore
Isolation Voltage • 3000 VAC Input to Output

1500 VAC Input to Ground
500 VAC Output to Ground

Signals • DC OK = Logic Low

AC Fail = Logic High
Global Inhibit = Logic Low
Enable = Logic Low

Overtemp = Logic Hi
LED Indicators • 2 status indicators
Size • 5.0” x 10.0” x 1.6”
Weight • 2.9 lbs. (1.3 kgs.)

Environmental

Operating • 0°C to +70 C, full power to +50 °C
Temperature derate from +50 °C to 70 °C

at 2.5%/°C
Cooling • Internal ball bearing fans
Humidity • <95% RH, non-condensing
Storage Temperature • -40 °C to +85 °C

EMC & Safety

Safety Approvals • UL1950, CSA C22.2 No 950,

EN60950 CE Mark LVD
EMC • EN61000-3-2, -3, EN55022 and FCC

20780 part 15J Class B conducted
Immunity & Surge • Meets EN61000-4-4, -5

800 Watts
ZC8 Series

AC/DC Front End

Specification

•

•

•

Hot Swap or Chassis Mount

Front End Switcher

•

Optional 3 Bay / 1U High Rack for

Hot-Swap 2+1 Redundant Operation

•

Active PFC - Meets EN61000-3-2, -3

•

World Wide Safety Approvals & CE Mark

•

OR’ing Diodes Standard on all Models

•

Single Wire Current Share

Intelligent Design Quality Product

XPiQ inc.

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

Package Maximum Output Maximum Model

Style Power Voltage Amps Number

650 W 12.0 V 54.2 A ZCA8HPS12

Hot Swap 700 W 24.0 V 29.2 A ZCA8HPS24

800 W 48.0 V 16.7 A ZCA8HPS48
650 W 12.0 V 54.2 A ZCA8CPS12

Chassis Mount 700 W 24.0 V 29.2 A ZCA8CPS24

800 W 48.0 V 16.7 A ZCA8CPS48

Hot Swap with Front Panel

480 W 12.0 V 40.0 A ZCA8HPS12C

IEC-320 Inlet with Switch

525 W 24.0 V 21.9 A ZCA8HPS24C
600 W 48.0 V 12.5 A ZCA8HPS48C

Chassis Mount with Front 480 W 12.0 V 40.0 A ZCA8CPS12C

Panel IEC-320 Inlet 525 W 24.0 V 21.9 A ZCA8CPS24C

with Switch 600 W 48.0 V 12.5 A ZCA8CPS48C

OUTPUT VOLTAGE & CURRENT RATINGS ZC8

1 Part numbers in bold type are standard stock models, all others including options below are build to order.

2. Standard airflow is front to rear. For optional reverse airflow add suffix R to the part number. Derate rear input models 20%, front panel IEC-320 inlet
models 16.6%.

3. Optional I C function by adding the suffix I to the part number.

4. Optional reverse airflow and I C function by adding the suffix M to the part number. Derate rear connector models 20%, front panel IEC-320 inlet
models 16.6%.

Notes

•

Mechanical Details - Power Supply

Notes:

1. Hot swap models are illustrated in
the mechanical drawing.
Chassis mount models do not have
handle or mounting bracket with
thumb-screw.

2. For unit to operate, Enable Pin
(Pin 7) must be at logic LO or
shorted to Pin 9.

3. For proper operation all output
pins (1-3) should be connected
together, Also, all returns pins (4-6)
should be connected together.

4. Pins 11, 12, 14, 17 & 19 functions
are only present with I

2

C option.

5. Dimensions shown in inches (mm).

6. Vertical blackplane mounting may
not allow for sufficient airflow.
Horizantal backplane, or additional
spacing with a vertical backplane is
recommended.

Pin Connections

Pin Function Pin Function

1 +V Out 13 Module Present
2 +V Out 14 DC Power Good/Add GA1
3 +V Out 15 AC Power Fail
4 V Return 16 V Trim
5 V Return 17 Overtemp. Warning/Add GA0
6 V Return 18 Current Share
7 Enable 19 Current Monitor/Add GA2
8 +Sense 20 +5V Standby

9 -Sense 21 Standby Return
10 Inhibit 22 Chassis Ground
11 Spare/SDA 23 AC Line
12 Spare/SCL 24 AC Neutral

Connector: Positronics PCIB24W9M400A1
Mate: PCIB24W9F400A1
Note: Output Connector is flush with the end of the case

±0.040 (1.02).

2

2

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com