Page 1
243X and
5020 Handle
Instructions
Part No. 068980-002
*068980-002*
*068980-002*
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
© 2001 Intermec
All Rights Reserved
243X and
5020 Handle
Instructions
Part No. 068980-002
*068980-002*
*068980-002*
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
© 2001 Intermec
All Rights Reserved
Warning
Take care when attaching the handle. The handle tips are sharp and
may cause bodily harm.
Avertissement
Faites attention lorsque vous attachez cette poignée. Les extrémités
de la poignée sont pointues et peuvent causer des blessures
corporelles.
Warning
Take care when attaching the handle. The handle tips are sharp and
may cause bodily harm.
Avertissement
Faites attention lorsque vous attachez cette poignée. Les extrémités
de la poignée sont pointues et peuvent causer des blessures
corporelles.
Page 2
243X and 5020
Handle Instructions
Installing the Handle
243X and 5020
Handle Instructions
Use these instructions to install the handle on the Trakker Antares® 243X hand-held
terminal or the 5020 Data Collection PC™.
Installing the Handle
1. Remove the handstrap. If you have a
243X, you must remove the handstrap
screw to remove the handstrap.
2. Position the handle as shown.
3. Tighten the screw so that the handle
does not move on the 243X or 5020. If
you have a torque screwdriver, tighten
the screw to 3.4 N-m (30 lb-in)
maximum.
Maintaining the Handle
You may need to periodically clean the
trigger mechanism, especially in dusty
environments. Grit between the small
magnet (in the end of the trigger mechanism
lever) and the 243X or 5020 case can cause
the trigger to jam.
1. Unscrew the handle and remove it from
the 243X or 5020.
2. Clean the surface of the 243X or 5020
and magnet with a damp cloth.
3. Use adhesive tape to remove any metal
shavings from the magnet surface.
4. Install the handle.
To clean the handle
Note: Do not overtighten the
screw in the handle. You may
damage the threads or cause the
trigger mechanism to jam.
243X5020I.eps
Handle
Handle tips
(2 places)
243X
or
5020
Installing the Handle
Use these instructions to install the handle on the Trakker Antares
®
243X hand-held
terminal or the 5020 Data Collection PC™.
Installing the Handle
1. Remove the handstrap. If you have a
243X, you must remove the handstrap
screw to remove the handstrap.
2. Position the handle as shown.
3. Tighten the screw so that the handle
does not move on the 243X or 5020. If
you have a torque screwdriver, tighten
the screw to 3.4 N-m (30 lb-in)
maximum.
Maintaining the Handle
You may need to periodically clean the
trigger mechanism, especially in dusty
environments. Grit between the small
magnet (in the end of the trigger mechanism
lever) and the 243X or 5020 case can cause
the trigger to jam.
1. Unscrew the handle and remove it from
the 243X or 5020.
2. Clean the surface of the 243X or 5020
and magnet with a damp cloth.
3. Use adhesive tape to remove any metal
shavings from the magnet surface.
4. Install the handle.
To clean the handle
Note: Do not overtighten the
screw in the handle. You may
damage the threads or cause the
trigger mechanism to jam.
243X5020I.eps
Handle
Handle tips
(2 places)
243X
or
5020
Loading...