Intermatic IG1CM, IG2TM, IG4TM, IG2T, IG1C Installation Instructions Manual

INSTALLATION INSTRUCTIONS

Telephone & Cable Indoor Stand Alone Protection

Surface Installation

Model Numbers: Description:

IG2TM 2-line telephone protector with indoor enclosure (NEMA 1)
IG4TM 4-line telephone protector with indoor enclosure (NEMA 1)
IG1CM 1-line coaxial cable protector with indoor enclosure (NEMA 1)

Optional Modules

IG2T 2-phone line protection module
IG1C coaxial cable protection module

Models

Before Installing

1. This device is intended for surface mounting. If unit is to be flush mounted (inside of wall) make sure that you
have the FLUSH MOUNTING KIT, part number IGFLUSH

.

2. Check the parts in the package against the Parts List shown above. Contact Intermatic if parts are missing.

3. It is suggested that you read these instructions completely before installing the Stand Alone Protection (SAP) unit.

SURGE PROTECTION

Description Quantity Reference

Mounting Frame 1 A
Cover / Back plate 1 B
IG2T (in Model IG2TM) 1 C
IG2T (2nd module in Model IG4TM) 1 D
IG1C(Coax module in model IG1CM) 1 E
Screws-self threading (3/8” Torx T20 / slot head) 2 F
Ground Wire 1 G
3/4” x 6 Pan Head Screws 4 (

not shown )

3/4” anchors 4 (not shown )

Parts List

A

A

C

D

G

G

F

E

F

B

B

Note: These modules rely on a good ground connection to function properly. Ground

availability should be a consideration when selecting an installation location.

Do not install Protection Devices during Electrical Storms.

Flat head screw driver, Torx T-20 head screw driver,
Awl or hole punch, drill, 1/8” and 3/16” bits.

T

ools Required

Notes:

1. Telephone protection is compatible with Voice
and Fax lines, Modem lines and DSL (Digital
Subscriber Lines.)

2. Coaxial protection is compatible with Local
antenna, Cable/Satellite and Cable Internet lines.

Installation

1. Select a location to install the Stand Alone Protector (SAP) that is convenient to telephone and /or coaxial cables. Allow enough
room to route the cables in and out of the unit. REMEMBER THAT THE GROUND CONDUCTOR MUST BE BONDED
(COMMON) WITH THE SERVICE ENTRANCE GROUND.

2. Remove the Cover (B) from the SAP unit by removing the two Torx Head screws (F) and separating the cover from the mount­ing frame (A).

3. Mark the position of the mounting holes located in the flange of the mounting frame on the wall or area surface and drill or
punch for installation of the anchors if required, and 3/4” pan head screws.

4. Secure the SAP Mounting Frame to the wall or vertical surface.

5. Route the cables to the SAP and secure the cables to the vertical surface.

6. Install the Ground Wire and make certain that it is properly connected to the building ground.

7. Allow approximately four inches (4”) of phone cable for each connection set. Leave enough slack in the cable to allow it to be
secured to the Mounting Frame without placing stress on the wires and terminals. Route the incoming phone cable (unprotect­ed) to the top of the unit (note the IN on the phone protection module). Route the protected phone cable to the bottom of the
unit (note the OUT on the phone protection module).

8. Remove 1 inch (1”) of jacket from both phone cables. Exercise caution
when removing the jacket to prevent nicking the individual wires.

9. Identify the pairs of wires to be protected and strip one-quarter inch (1/4”)
of insulation from each wire in both the IN and OUT phone wires.
Exercise caution when removing the insulation to prevent nicking the
individual wires.

10. Insert the first pair of wires into the terminal strip marked CN1 located at
the IN side of the protection module. Secure the wires by tightening the
screw in the head of the terminal. Do not overtighten. The wires are
secure if a gentle pull on the wire does not dislodge it from the terminal.

11. Locate the identical pair of wires by color marking in the cable at the OUT
or PROTECTED side of the protection module and insert and secure
them in terminal strip marked CN3. Be sure to match the polarity (wire
markings) of the pair of wires connected to terminal strip CN1.

12. Repeat steps 8 through 10 for each line (pair of wires) using successive
positions in terminal strips CN1 and CN2 for input and CN3 and CN4 for
output.

13. Position all unused wires away from the protection module to prevent shorting. Unused wires may be cut off if additional phone
lines are not anticipated in the future.

14. Secure the IN and OUT cables to the Mounting Frame. Make sure that the cables will not interfere with the Cover when it is
replaced.

15. Refer to the COAXIAL CABLE section below if Coaxial protection is used.

16. When wiring is complete, replace the Cover / back plate that was removed in step #2 above and secure it with the Torx Head
screws.

17. TEST each phone line for proper operation.

Coaxial Protection

1. Follow steps 1 through 6 above.

2. Connect the cable to the IG1C module using F-thread coax connectors. The IG1C module is bi-directional and IN and OUT
Coax connectors may be connected to either position.

3. Follow steps 14 and 16 above.

4. TEST each coax line for proper operation.

INTERMATIC INCORPORATED

Spring Grove, Illinois 60081

http://www.intermatic.com

158IG12078

For troubleshooting assistance, call Intermatic at 1-800-391-4555.

1st pair IN

2nd pair IN

1st pair OUT

2nd pair OUT

NOTE:

In the event that the Telephone surge protection circuit should fail due to excessive energy, it may result in an “OFF HOOK” condition
for telephone lines. The protector should be bypassed until a replacement unit is obtained and installed. In the case of a Coax pro­tector failure, the signal to the equipment may be interrupted or degraded. The protector should be bypassed until a replacement
unit is obtained and installed.

IN IN

CN1 CN2

CN3

OUT OUT

CN4

IN IN

CN1 CN2

CN3 CN4

OUT OUT