Intermatic H0007 User Manual
-------------------------------------- DRAFT COPY -------------------------------------Instructions for Model HA07 – Master Remote Controller
<Front cover>
User’s Manual
*Illustration of HA07 controller*
<Inside cover>
General Description
Federal Communications Commission Statement
This device complies with part 15 of the FCC rules. Operation of this device is subject to
the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna or device.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
WARNING!
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Enclosed you will find:
1 Master Remote Controller
Installation Instructions
Remote Controller
1. Open the battery compartment located on the back of the remote controller by
pressing down on the battery compartment tab and pulling the door outward.
2. Insert 4 “AA” alkaline batteries (not included) with polarities as shown.
3. Replace the battery compartment by first inserting the 2 tabs at the bottom of the
door, then pressing the door in until the door ‘clicks’ shut.
Z-wave Compatible Module:
1. Install a Z-wave compatible module as described by its instruction manual.
2.
Do not exceed the maximum ratings of the module.
Operating Instructions
Creating a Network
1. On the remote controller, the include button is located behind a protective lid.
Raise the lid to gain access to the
2. Press and release the include button. The INCLude icon in the LCD display will
begin to flash indicating that the controller is ready to register modules.
3. On the Plug-in Dimmer, press and release the
“INCL” icon on the controller will stop flashing and the word “SUCCESSFUL”
will turn on steady in the LCD display for 2 seconds. If not successful, the words
“NOT SUCCESSFUL” will turn on steady in the LCD display for 2 seconds.
4. Repeat steps 2 & 3 for each module you wish to add to the network.
Assigning Modules to Channels
1. On the remote controller, press and hold the ON and OFF buttons for the channel
to which you want to assign a module at the same time. After about 3 seconds, the
word, “LEARN” will be displayed in the LCD display. This indicates that the
controller is ready to assign a module to that channel. You may now release the
ON and OFF buttons.
2. Press and hold the Include button. The INCLude icon will turn on.
3. While still holding the Include button in step 3, press and release the
on the module. Do not release the Include button on the controller yet.
4. Choose a light level by pressing and holding, or pressing and releasing the
button on the module. Possible settings are FULL ON or FULL OFF, (or DIM
LEVEL for dimmable modules).
5. After reaching your desired light level, release the Include button on the remote
controller. The remote controller will automatically store the light level that you
have just set. The word “SUCCESSFUL” will turn on for 2 seconds and the
module is now associated to that channel with a default light level assigned.
Include and Exclude buttons.
black button. If successful, the
black button
black
Remotely turning ON and OFF and Dimming a module
1. To turn ON a module, press and release the ON button for that module’s given
channel.
2. To turn OFF a module, press and release the OFF button on for that module’s
given channel.
3. To dim a module up, press and hold the ON button. To dim a module down, press
and hold the OFF button.
Model HA07 – Mater Remote Controller – Specifications
Range: >50 feet
Uses 4 size “AA” alkaline batteries. 1.5VDC ea.
Suitable for use in dry locations.
Made in China.
Loading...