Intermatic FM/1 Series Operating Instructions Manual

45 3

1

M

INPUT

COM

NO

NC

2

________________________________________________________________

http://waterheatertimer.org/Intermatic-timers-and-manuals.html#PB

http://waterheatertimer.org/Intermatic-trippers-and-parts.html

FM/1 Series

Time Switches

APPLICATIONS

The FM/1 series of time switches are designed for control of
heating, ventilating, air conditioning, refrigeration, lighting,
security, circulating pumps, spas or any electrical load requir­ing 24-hour or 7-day scheduling.

WIRING

Verify input voltage stated on back of unit. Use 1/4” quick con­nects and make connections in accordance with the wiring
diagram shown and applicable code requirements. When
using 24V units, it is important to use transformers that will

supply the required 24 volts AC to terminals 1 & 2.

TECHNICAL DATA

Supply Voltage: 24, 120 and 240VAC, 60Hz models

Quartz: 24V AC/DC, 120 and
240VAC 50/60 Hz

Switch Type: SPDT

Switch Rating: 21A/250VAC resistive

1350 watt tungsten
1HP @ 125VAC
2HP @ 240VAC

Power
Consumption:

Ambient
Temp. Range: –40°F to 180°F, synchronous units

Terminals: 1/4” spade terminals

24V: 0.1VA; 120V: 0.5VA; 240V: 1.0VA

–20°F to 140°F, quartz units

Terminal Connections

Contacts shown in “Off” position (trippers pushed inward)

“On” position (trippers pushed outward) will close contacts 3 & 4

MOUNTING

The standard FM/1 units can be flush mounted (mounting kit
with screws available) or surface mounted inside a panel. A
printed circuit board mounting base is also available. An
indoor or outdoor enclosure is available for stand-alone
mounting. In addition, unit is also available in DIN housing for
flush or surface mounting (see MIL72, Digi 20 or Digi 42 data
sheets). Optional clear plastic dust cover is available.

Reserve Carryover:

Weight: Approximately 3 oz.

NOTE: 24V quartz unit will operate on 6VDC, 12VDC,

or 24VDC

7 days for quartz units

Dimensions

FM/1 synchronous/quartz

PROGRAMMING WITH MANUAL
OVERRIDE SWITCH

AUTOMATIC MODE

In order to operate the time switch module in the automatic
mode, the manual switch must be in the center position (auto­matic) - see diagram.

MANUAL MODE

With the manual switch selector lever the selected programs
can be overridden. In the lower position, marked “O”, termi­nals 3 and 5 are permanently closed. In the upper position,
marked “I”, terminals 3 and 4 are permanently closed (see
diagram).

Override Mode

TIME SETTING

TO SET THE CURRENT TIME (AND DAY OF WEEK
ON 7 DAY UNITS), TURN THE MINUTE HAND
CLOCKWISE. DO NOT SET THE TIME BY ROTAT­ING “OUTER” DIAL.

Turn the minute hand clockwise until the day of the week
(7-day timer) and the time of day on the outer dial is
aligned with the triangle marker on the inner dial (two
o'clock position).

Example for 7-day program dial Monday 10:30 AM. Turn the
minute hand clockwise until Monday 10:30 AM is aligned
with the triangle on the inner dial. The hour and minute hand
will show exactly 10:30.

Example for 24-hour program dial 10:30 AM. Turn the minute
hand clockwise until 10:30 AM is aligned with the triangle on
the inner dial. The hour and the minute dial will show exact­ly 10:30.

PROGRAMMING

7-Day (SW, QRW Models)

The weekly program dial reflects the seven days of the week
and AM/PM imprints for each day.

The time switch is programmed by pushing the captive trip­pers to the outer ring position for the entire period that the
load is to be turned “ON”, i.e., two hours for each tripper on
the 7-Day dial. When the tripper is pushed to the inside, the
switch is in the “OFF” position.

3-way manual
override switch

I = permanent ON

= automatic

0 = permanent OFF

24-Hour (ST, QRT Models)

The 24-Hour dial has quarter-hour divisions and AM/PM indi­cations.

The time switch is programmed by pushing the captive trip­pers to the outer ring position for the entire period that the
load is to be turned “ON”, i.e., fifteen minutes for each trip­per on the 24-Hour dial. When the tripper is pushed to the
inside, the switch is in the “OFF” position.

Intermatic Incorporated • Spring Grove, IL 60081 • www.intermatic.com

300GR10020

PROGRAMMING SHEET

Rotate the outer dial slowly in a clockwise
direction, until the right corresponding day
segment on the dial is approaching the
arrowhead printed on the inside edge of the
dial. Do not attempt to rotate the dial or the
clock hands in an anti-clockwise direction.

Now rotate the minute hand with your finger, in
a clockwise direction, so that you set the correct
time within the day segment. Note that the
clock hands are set within a 12-hour printed
ring, and the outer dial is printed with the 24
hour clock. The illustrations show the clock set
at 6:00 a.m. (fig. 1) and 6:00 p.m. (fig. 2) on
Monday. Ensure that you are setting current
time accurately with regard to the outer 24 hour
dial.

Tappets should be pushed to the outer edge of
the dial for a programmed ON instruction, and
left set to the inner edge of the dial for a
programmed OFF instruction. All tappets
between the desired ON and OFF times must be
pushed to the outer edge of the dial. Each
tappet switches the output for a two-hour
period. Figure 3 shows the timeswitch set for
8:00a.m. ON – 18:00 (6:00p.m.) OFF Monday –
Saturday and no switching programmed on
Sunday.

There is a three-position switch

built in to the
face of the dial.
For automatic timed control, governed by the
tappet settings, the switch should be left in the
middle position (as illustrated). The output can
be switched ON at any time, by moving the
switch lever to the top position, marked with "I"
on the dial. Alternatively, the output can be
switched OFF at any time, by moving the switch
lever to the lower position, marked with "0" on
the dial. The manual override is a fixed
selection – the output will remain ON or OFF (as
selected), until the switch lever is moved back
to the middle timed position, marked with a

on the dial.

7 Day analogue timeswitches

Fig. 1

Fig. 2

Fig. 3

Set time and day

Setting switching times

Manual override

www.intermatic.com

Energy ControlsEnergy Controls

Mechanical

Timer Modules

FM1STUZ-120U

Features:

•21ASPDTswitch

•96CaptiveTripp ers

•1⁄4in.quick-connectterminals

•NoiseImmune—Idealforrobust

applications

FM/1 Series

24-Hour, 7-Day

Applications:

The FM/1 series mechanical timer modules are designed to be placed inside a

machinecontrolpanel,circuitboard,orotherequipment.Itoffersupto21Amp

switching designed for control of heating, ventilating, air conditioning, refrigeration,

lighting,security,circulatingpumps,spasoranyelectricalloadrequiring24-houror

7-day scheduling.

Specifications:

Size: 3.25 in. H x 3.25 in. W x 2.25 in. D
Supply Voltage: 24, 120, 240 VAC
Power Consumption: 1 VA
Switch Rating: SPDT
Resistive: 21 Amp
Tun gsten: 1350 W
Inductive: 1 HP, 125 VAC; 2 HP, 240 VAC
Wiring Connections: 1⁄4in.quick-connectterminals
Operating Temperature Range:“S”models–40ºFto185ºF(–40ºCto85ºC)

“Q”models–20ºFto131ºF(–20ºCto55ºC)

Installation: Stand alone or with Indoor/Outdoor enclosure
Panel: Surface mounting

Min Switch
Model Switch Battery ON/OFF Output
Number Override Program Backup Time Volts AC Type/Amps

FM1STUZ-120U No 24 Hr. No 15 Minutes 120 SPDT/21
FM1STUZ-24U No 24 Hr. No 15 Minutes 24 SPDT/21
FM1STUZ-240U No 24 Hr. No 15 Minutes 240 SPDT/21
FM1SWUZ-120U No 7 Day No 2 Hours 120 SPDT/21
FM1SWUZ-24U No 7 Day No 2 Hours 24 SPDT/21
FM1SWUZ-240U No 7 Day No 2 Hours 240 SPDT/21
FM1STUZH-120U Yes 24 Hr. No 15 Minutes 12 0 SPDT/21
FM1STUZH-24U Yes 24 Hr. No 15 Minutes 24 SPDT/21
FM1STUZH-240U Yes 24 Hr. No 15 Minutes 240 SPDT/21
FM1SWUZH-120U Yes 7 Day No 2 Hours 120 SPDT/21
FM1SWUZH-24U Yes 7 Day No 2 Hours 24 SPDT/21
FM1SWUZH-240U Yes 7 Day No 2 Hours 240 SPDT/21
FM1QTUZH-120U Yes 24 Hr. Yes 15 Minutes 120 SPDT/21
FM1QTUZH-24U Yes 24 Hr. Yes 15 Minutes 24 SPDT/21
FM1QTUZ-120U No 24 Hr. Yes 15 Minutes 120 SPDT/21
FM1QTUZ-24U No 24 Hr. Ye s 15 Minutes 24 SPDT/21
FM1QTUZ-240U No 24 Hr. Yes 15 Minutes 240 SPDT/21
FM1QWUZ-120U No 7 day Yes 2 Hours 120 SPDT/21
FM1QWUZ-240U No 7 day Yes

2 Hours 24

0

SPDT/21
FM1QWUZH-120U Yes 7 Day Yes 2 Hours 120 SPDT/21
FM1QWUZH-240U Yes 7 day Yes 2 Hours 240 SPDT/21
FM1QWUZH-BW-24U Yes 7 day Yes 2 Hours 24 SPDT/21
FM1STUZH220/50 Ye s 24 Hr. No 15 Minutes 220 SPDT/21

(50 Hz)

FM1STUZ220/50 No 24 Hr. No 15 Minutes 220 SPDT/21

(50 Hz)

0.25 lbs
.01 kg

C2 2.2-17 7

LR3730

UL917

H VA C / R

21

How to set Intermatic FM1 timers

The FM1 series timer can be wired and programmed for
different purposes.

Since the timer has NO NC terminals, the best way to proceed
is to 1) wire your timer 2) turn power on 3) move 10 tripper
pins outward, 4) leave rest of tripper pins inward.

5) Then manually rotate dial to watch when load turns on-off.

If timer model has manual override button, then move override
switch to each of 3 positions and repeat same test.
These actions will reveal correct wiring and switch setting for
your purpose.

Other Intermatic Modular timers

http://waterheatertimer.org/Intermatic-trippers-and­parts.html#PB

7-day timer dial: each tripper is 2 hours
24 hour dial: each tripper is 15 minutes