Inter-M V2-2000 User Manual

Operation Manual

Professional Power Amplifier

V2-1000/2000/3000/4000

PROFESSIONAL POWER AMPLIFIER

Welcome

Welcome

A personal welcome to you from the management and employees of Inter-M

All of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value,
and we are delighted you have purchased one of our products.

We sincerely trust this product will provide years of satisfactory service, but if anything is not to your complete
satisfaction, we will endeavor to make things right.

Welcome to Inter-M, and thank you for becoming part of our worldwide extended family!

This symbol is int ended to ale rt the user to the

CAutION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Caution: To prevent electric shock do not use this (polarized) plug with

Attentions: Pour prévenir les chocs électriques ne pas utiliser cette

WARNING

To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

*WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING-WATER AND MOISTURE: Unit should not be used near water(e.g.

near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do
not fall and liquids are not spilled into the enclosure through openings.

*CLASS 2 WIRING (Adjacent to speaker terminal): The speaker output of this apparatus can exceed 10 Watts and could be a shock injury.

Connection to speakers should be performed by a skilled person.
*Do not install this equipment in a confined space such as a book case or similar unit.
*This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus.
*This apparatus shall be connected to a mains socket outlet with a protective earthing connection.

It has heed to be easy to disconnect the device. To disconnect the device from power, separate AC input cable from inlet or unplug the AC Cord.

*

CAutION

*These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing

other than that contained in the operating instructions unless you are qualified to do so.

NOtE
*This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

presence of uninsulated “dangerous voltage” within
the product’s enclosur e that ma y be of sufficient
magnitude to constitute a risk of electric shock to
persons.

This symbol is int ended to ale rt the user to the
presence of important operation and maintenance
(servicing) instructions in the literature accompanying
the appliance.

an extension cord, receptacle or other outlet unless the blades
can be fully inserted to prevent blade exposure.

fiche polarisée avec un prolongateur, une prise de courant
on une autre sortie de courant, sauf si les lames peuvent
étre inséré es à fond sans en lai sser aucune par tie à
découvert.

PROFESSIONAL POWER AMPLIFIER

Contents

Contents

Unpacking .......................................................................................................................................2

Short Form Instructions .................................................................................................................2

Installation

Environment....................................................................................................................................3

Important Safety Instructions.............................................................................................................3

Description.......................................................................................................................................4

Features............................................................................................................................................4

Front Panel ......................................................................................................................................5

Rear Panel .......................................................................................................................................7

Applications

Stereo Installation............................................................................................................................9

Parallel Installation ..........................................................................................................................9

Bridge Mono Installation ................................................................................................................10

Linked Installation..........................................................................................................................10

Connections..................................................................................................................................11

Stereo/Parallel Connection ............................................................................................................12

Bridge Mono Connection ...............................................................................................................12

Block Diagram ..............................................................................................................................13

Specifications ................................................................................................................................14

Service

Procedures....................................................................................................................................16

Schematic.....................................................................................................................................16

Parts List .......................................................................................................................................16

Variations and Options ...............................................................................................................16

Warranty .......................................................................................................................................16

V2-1000/2000/3000/4000

1

PROFESSIONAL POWER AMPLIFIER

Unpacking

Unpacking

Please take a few minutes to read this manual to familiarize yourself with important information regarding
installation, product features, and operation.

As with most electronic devices, original packaging (or equal) is required in the unlikely event that the product
needs to be returned for servicing.

Short Form Instructions

Short Form Instructions

1. Do not connect the AC power until step 6. The ac mains power switch should be in the off position.

2. Adjust both of the level controls to the fully attenuated position(turn fully counter-clockwise).

3. Connect an appropriate line level input signal to the balanced XLR connector marked inputs.

4. Move the mode selector to the desired position. The Stereo position is the most common.

5. Connect the outputs to the speaker load according to the mode of operation determined in the previous step.

6. With the ac mains power switch in the off position, connect to an appropriate AC source.

7. Depress the ac mains power switch to the on position. The indicator ‘POWER’ will illuminate dimly and then
fully after a few seconds.

8. The product is ready for operation. Slowly increase the level control to the desired operating level. Avoid
illuminating the clip indicator and do not apply too much power to the speakers.

9. Operate the product and the system in a manner which does not illuminate the clip warning indicator.

2

V2-1000/2000/3000/4000

PROFESSIONAL POWER AMPLIFIER

S3125A

Installation

Installation

Environment

Never place this product in an environment which could alter its performance or reduce its service life. Such
environments usually include high levels of heat, dust, moisture, and vibration.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.

S3125A

V2-1000/2000/3000/4000

3

PROFESSIONAL POWER AMPLIFIER

Description

Description

- V2-1000
A 2U rack space, 2 channel amplifier capable of 1150W into 4Ωload(bridged mono).

- V2-2000
A 2U rack space, 2 channel amplifier capable of 1850W into 4Ωload(bridged mono).

- V2-3000
A 2U rack space, 2 channel amplifier capable of 3300W into 4Ωload(bridged mono).

- V2-4000
A 2U rack space, 2 channel amplifier capable of 4200W into 4Ωload(bridged mono).

※

The output power can be changed in relation to the AC supply voltage.

Features

Features

- 2Ω-load stable per channel, 4Ω-load stable in bridged mono

- 2U rack space

- Switch mode power supply available for high efficiency and low weight

- Forced air cooled(front panel intake, rear panel exhaust)

- Front panel indicators for output signal, clip, protect and power

- Rack ears for permanent installation in a standard 19”(rack mount width) enclosure

- Selectable high pass filter on each channel-clip limiter circuitry

- Gain selectable switch for both channel

- Front removable dust filters

4

V2-1000/2000/3000/4000

Front Panel

1 3 42 5 76

Front Panel

PROFESSIONAL POWER AMPLIFIER

1. HANDLES

These are provided for easy transporting and installing into equipment enclosures or racks.

2. SCREW FOR DUST FILTER REMOVAL

To avoid unnecessary dust particles being drawn into amplifier, a removable dust filter has been fitted to the
front panel.

3. LEVEL CONTROL

This control adjusts the level(amplitude) of the input signal for each channel. In stereo or parallel mode the
knobs will determine the signal level independently for each channel. In the bridged mono mode only
channel A knob will be determine the signal level, while channel B disabled.

4. LEVEL INDICATOR

These indicators should illuminate during normal operation when there is an output signal.

5. PROTECTION/CLIP INDICATOR

This warns of a problem when illuminated. Reduce the level of the device which supplies signal to the
amplifier or reduce the level control(s) on the amplifier. This should not be continuously illuminated during
normal operation, but may flash occasionally. Also this indicates protection occurred like the amplifier over
heated, output shorted, over loaded and unexpected DC voltage output, which result the amplifier shutdown.
When protection released, the amplifier should be recovered.

6. POWER INDICATOR

This confirms the amplifier is switched on and receiving AC mains power when illuminated. When switched
on, the indicator is illuminated dimly for stand-by and then fully illuminated with prot/clip indicator for mute
status, after that, only this illuminated fully activating the amplifier.

V2-1000/2000/3000/4000

5

PROFESSIONAL POWER AMPLIFIER

7. POWER SWITCH

2-Series have a combination AC switch/circuit breaker. The position of this switch determines whether the AC

V
mains power is on or off. The power-on status is confirmed by the illuminated power indicator. Also this is
used for a circuit breaker to protect AC mains power and the amplifier from abnormal operations due to
overload or malfunction. If the current flows over the circuit breaker's rating, the circuit breaker is tripped.
You can switch on after abnormal situation released and then the amplifier will be recovered. Amplifiers are
always the last item in a system to be turned on. It is generally a good idea to reduce the level controls
before applying AC mains power.

6

V2-1000/2000/3000/4000

Rear Panel

Rear Panel

PROFESSIONAL POWER AMPLIFIER

1. AC CORD

Connect this product to an appropriate AC main power source.

2. OUTPUT CONNECTORS

4 Pole speaker sockets are provided. Bridged mono operation requires a different method of connecting the
speaker cables than stereo operation. Be sure that the amplifier is in the correct mode before connecting the
speaker load. Please refer to the output connection drawings.

3. MODE SELECTOR SWITCH

Move this switch to select the stereo, parallel or bridged mono position as needed for the application. The
stereo mode is most common. Channel A input provides signal through the amplifier to the channel A
output. The channel B input provides signal through the amplifier the channel B output. The parallel mode
uses the channel A input provides signal through the amplifier to both the channel A and channel B outputs.
No input will be supplied to channel B in the Parallel mode. The bridge mono mode combines both channels
to create one larger mono channel. Input signal applied to channel A will provide signal through the
amplifier to the positive terminals of channel A and channel B. Do not connect any signal to the channel B
input or any loads to the negative outputs.

4. VOLTAGE GAIN SELECTOR SWITCH

You can drive the amplifier with different gain structure, 1V, 32dB or 26dB, which is possible the amplifier
to accept a various input level. (V2-1000/2000 Voltage Gain: 1V, 26dB, 20dB)

5. BALANCED TRS INPUT CONNECTORS

Each input channel is equipped with a TRS connector. The signal at these connectors is parallel with the XLR
input signal for linking the input signal to other amplifier.

V2-1000/2000/3000/4000

7

PROFESSIONAL POWER AMPLIFIER

6. BALANCED XLR INPUT CONNECTORS

ach input channel is equipped with a XLR connector. You can use either balanced or unbalanced

E
connectors, but recommend using unbalanced only for a short distance between equipment to avoid a noise
problem. Please refer to the input connection drawings.

7. CLIP LIMITER SWITCH

The clip limiter reduces the internal operating level of the amplifier as necessary to insure that signal peaks
do not overdrive the amplifier, causing distortion or damage to the amplifier or loudspeakers. It is
recommended to leave this switch to the “ON” mode to reduce distortion and help to provide protection to
the loudspeakers.

8. HIGH PASS FILTER SWITCH

Select the switch position that is suited for your application the most. The off position allows full frequency
range signals to reach the loudspeakers. The 30Hz position reduces the signal amplitude below 30Hz to
conserve power and help protect the loudspeakers. The 50Hz position reduces the signal amplitude below
50Hz to conserve power and help protect the loudspeakers.

8

V2-1000/2000/3000/4000

Applications

Applications

ApplicationsApplications

Stereo Installation

PROFESSIONAL POWER AMPLIFIER

Parallel Installation

V2-1000/2000/3000/4000

9

PROFESSIONAL POWER AMPLIFIER

Applications

Applications

Bridged Mono Installation

Linked Installation

In V2-Series, Linking is possible when in Stereo/Parallel or Bridged Mono operation.

10

V2-1000/2000/3000/4000

Applications

Applications

Connections

Inter-M products are wired according to professionally accepted wiring practices used throughout the world.

1. XLR INPUTS

Balanced XLR connectors are wired as described:
Pin #1 Shield
Pin #2 Positive
Pin #3 Negative

XLR MALE

PROFESSIONAL POWER AMPLIFIER

2. TRS INPUT

Balanced 1/4″TRS connectors are wired as described:

Tip is Positive
Ring is Negative
Sleeve is Shield

PHONE JACK

V2-1000/2000/3000/4000

11

PROFESSIONAL POWER AMPLIFIER

3. OUTPUTS

ridged Mono operation has a minimum load impedance of 4Ω.

B

Stereo/Parallel Connection

Wiring Using Both Speaker Connectors

Wiring Two Speakers to the Channel A Speaker Connector

Bridge Mono Connection

Wiring a Speaker in Bridged Mono to the Channel A Speaker Connector

12

V2-1000/2000/3000/4000

Block Diagrams

Block Diagram

V2-1000/2000

PROFESSIONAL POWER AMPLIFIER

V2-3000/4000

V2-1000/2000/3000/4000

13

PROFESSIONAL POWER AMPLIFIER

Specifications

Specifications

V2-1000 V2-2000 V2-3000 V2-4000

120VAC 230VAC 120VAC 230VAC 120VAC 230VAC 120VAC 230VAC

Continuous Average Output Power Per Channel

Stereo Mode 8Ω(T.H.D 0.1%) 190W 180W 320W 300W 550W 550W 750W 750W
(1kHz, Both Channels Driven) 4Ω

Bridged Mono Mode 8Ω(T.H.D 0.1%)

I

nput Sensitivity (Rated Output Power @4Ω)
Voltage Gain (Rated Output Power @4
Frequency Response
(1W @8Ω)
Damping Factor (100Hz, Rated Output Power @8Ω)
T.H.D

(20Hz~20kHz, 10dB Below Rated Output Power @4Ω)
Channel Separation

(1kHz, 3dB Below Rated Output Power @8Ω)
Residual Noise less than 75dB less than 73dB
Signal to Noise Ratio

(Rated Output Power @8
Output Circuitry Class AB 2 Step Class H
Input Impedance 12 k
HPF (30Hz/50Hz) 12dB/oct
Indicators Prot/Clip, Signal, Power

Protection Circuitry

Cooling Variable Speed Fans, Front to Rear Air Flow

(T.H.D 0.1%) 340W 320W 550W 530W

2Ω(T.H.D 0.5%) 580W 580W 900W 900W

720W 700W 1150W 1100W 2000W 2000W 2600W 2600W

4Ω(T.H.D 0.5%)

20Hz~20kHz

- 3dB point 5Hz~70kHz

Ω

, 20Hz~20kHz)

1200W 1150W 1900W 1850W 3200W 3300W 4000W 4200W

1.1V 1V 1.1V 1V

Ω

) 31dB 33dB 36dB 37dB

±0.3dB

more than 380 more than 450 more than 400

less than 0.05%

less than 70dB

106dB

Ω

Balanced

Full Short Circuit, Thermal Protection

Power ON/OFF Muting, DC Output Protection

1000W 1000W 1300W 1300W
1600W 1650W 2000W 2100W

Connectors Input : XLR(Female), 1/4″TRS,

Output : 4 Pole Speaker Socket
Operating Temperature/Humidity Temperature : -10°C~ +40°C/ Humidity : 0% ~ 90%
Power Source

120VAC 230VAC 120VAC 230VAC 120VAC 230VAC 120VAC 230VAC

60Hz 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 50Hz

dB=1V

0

14

Power Consumption
(1/8 Rated output power @4Ω)

Weight (SET)

6A

3A

8A

4A

12A

6A

14A

10.7kg / 23.6lb 10.9kg / 24lb 12kg / 26.4lb 12.1kg / 26.7lb

Dimensions (SET) 482(W) x 88(H) x 407(D)mm / 19(W) x 3.5(H) x 16(D)in

* Specifications and design subject to change without notice.

V2-1000/2000/3000/4000

7A

PROFESSIONAL POWER AMPLIFIER

Specifications (U.K/Australia Version)

Specifications

V2-1000 V2-2000 V2-3000 V2-4000

240VAC 240VAC 240VAC 240VAC

Continuous Average Output Power Per Channel

Stereo Mode 8Ω(T.H.D 0.1%) 170W 280W 500W 650W
(1kHz, Both Channels Driven) 4Ω

Bridged Mono Mode 8

I

nput Sensitivity (Rated Output Power @4Ω)
Voltage Gain (Rated Output Power @4
Frequency Response
(1W @8Ω)
Damping Factor (100Hz, Rated Output Power @8Ω)
T.H.D

(20Hz~20kHz, 10dB Below Rated Output Power @4Ω)
Channel Separation

(1kHz, 3dB Below Rated Output Power @8Ω)
Residual Noise less than 75dB less than 73dB
Signal to Noise Ratio

(Rated Output Power @8
Output Circuitry Class AB 2 Step Class H
Input Impedance 12 k
HPF (30Hz/50Hz) 12dB/oct
Indicators Prot/Clip, Signal, Power

Protection Circuitry

Cooling Variable Speed Fans, Front to Rear Air Flow

(T.H.D 0.1%) 300W 500W 900W 1150W

Ω

(T.H.D 0.5%) 500W 850W 1400W 1800W

2

Ω

(T.H.D 0.1%)

4Ω(T.H.D 0.5%)

Ω

) 31dB 33dB 36dB 37dB

20Hz~20kHz

- 3dB point 5Hz~70kHz

Ω

, 20Hz~20kHz)

650W 1000W 1800W 2400W

1100W 1700W 3000W 3800W

1V

±0.3dB

more than 380 more than 450 more than 400

less than 0.05%

less than 70dB

106dB

Ω

Balanced

Full Short Circuit, Thermal Protection

Power ON/OFF Muting, DC Output Protection

Connectors Input : XLR(Female), 1/4″TRS,

Output : 4 Pole Speaker Socket
Operating Temperature/Humidity Temperature : -10°C~ +40°C/ Humidity : 0% ~ 90%
Power Source

240VAC

50Hz

dB=1V

0

Power Consumption
(1/8 Rated output power @4Ω)

Weight (SET)

4A

5A 6A 7A

10.7kg / 23.6lb 10.9kg / 24lb 12kg / 26.4lb 12.1kg / 26.7lb

Dimensions (SET) 482(W) x 88(H) x 407(D)mm / 19(W) x 3.5(H) x 16(D)in

* Specifications and design subject to change without notice.

V2-1000/2000/3000/4000

15

NOTE

Service

Service

Procedures

Ensure the problem is not related to operator error, or external system devices, Once it is certain that the
problem is related to the product contact your warranty provider as described in the warranty section of this
manual.

Schematic

A Schematic is available by contacting your warranty provider.

Parts List

A Parts List is available by contacting your warranty provider.

Variations and Options

Variations and Options

Variations

Variations of this product exist to reflect the variations in AC power requirements throughout the world. Product
supplied through local sources are compatible with local AC power requirements.

Options

No optional items are available for this product.

Warranty

Warranty

Warranty terms and conditions vary by country and may not be the same for all products. Terms and conditions
of warranty for a given product may be determined first by locating the appropriate country which the product
was purchased in, then by locating the product type.

To obtain specific warranty information and available service locations contact Inter-M directly or the
authorized Inter-M Distributor for your specific country or region.

16

V2-1000/2000/3000/4000

V2-1000/2000/3000/4000

20

Inter-M, Ltd. (Korea) began operations in 1983.

Since then, Inter-M has grown to become one of the largest manufacturers
of professional audio and commercial sound electronics equipment in the world.

Inter-M has gained worldwide recognition for its own branded products,
as well as private label manufacturing of electronics sold under other names (OEM).

The company is no longer just a Korean company, but rather a global company
that is truly international in scope, with factories and offices in Korea and China,
and sales and marketing operations located in Japan, Europe, and the U.S.A.

With more than 850 employees around the globe,
Inter-M is well-poised for further growth and expansion.

Inter-M Americas, INC.

13875 ARTESIA BLVD. CERRITOS, CA 90703 USA
TEL : [phone], FAX : [phone]
Home Page : http://www.inter-m.net, E-mail : [e-mail]

Inter-M Corporation

SEOUL OFFICE:653-5 BANGHAK-DONG, DOBONG-KU, SEOUL, KOREA
TEL : [phone]~8, FAX : [phone]
Home Page : http://www.inter-m.com, E-mail : [e-mail]

MADE IN KOREA

November 2010 127364