Inter-M AOE-212N User Manual

Operation Manual

Audio Over Ethernet

AOE-212N

* Rack mount products in the Western Hemisphere(North America, South America, and the Caribbean) do not have handles installed due to customer preference.

AUDIO OVER ETHERNET

Welcome

A personal welcome to you from the management and employees of Inter-M

All of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value, and we are delighted you have purchased one of our products.

We sincerely trust this product will provide years of satisfactory service, but if anything is not to your complete satisfaction, we will endeavor to make things right.

Welcome to Inter-M, and thank you for becoming part of our worldwide extended family!

This s ymb ol is inten de d to alert t he use r to the

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Caution: To prevent electric shock do not use this (polarized) plug with

Attentions: Pour prévenir les chocs électriques ne pas utiliser cette

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

*WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING-WATER AND MOISTURE: Unit should not be used near water(e.g.

near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do not fall and liquids are not spilled into the enclosure through openings.

*CLASS 2 WIRING (Adjacent to speaker terminal): The speaker output of this apparatus can exceed 10 Watts and could be a shock injury.

Connection to speakers should be performed by a skilled person. *Do not install this equipment in a confined space such as a book case or similar unit. *This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus. *This apparatus shall be connected to a mains socket outlet with a protective earthing connection.

It has heed to be easy to disconnect the device. To disconnect the device from power, separate AC input cable from inlet or unplug the AC Cord.

CAUTION

*These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing

other than that contained in the operating instructions unless you are qualified to do so.

NOTE *This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

presence of uninsulated “dangerous voltage” within the product’ s enclosu re that m ay be of su fficient magnitude to constitute a risk of electric shock to persons.

This s ymb ol is inten de d to alert t he use r to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance.

an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

fiche polarisée avec un prolongateur, une prise de courant on une autre sortie de courant, sauf si les lames peuvent étre i nséré es à fon d sans en l aisse r aucun e parti e à découvert.

AUDIO OVER ETHERNET

Contents

Unpacking.............................................................................................................................2

Installation

Environment ..........................................................................................................................2

Important Safety Instructions .....................................................................................................2

Features.................................................................................................................................3

Composition and accessory.....................................................................................................3

Front Panel............................................................................................................................4

Rear Panel ............................................................................................................................6

Equipment setting using AOE-212N internal CGI server ..........................................8

Device structure block ......................................................................................................20

How to connect ..................................................................................................................21

Applications ........................................................................................................................22

Block Diagram....................................................................................................................23

Specification .......................................................................................................................24

Service

Procedures...........................................................................................................................26

Schematic............................................................................................................................26

Parts List ..............................................................................................................................26

Variations and Options....................................................................................................26

Warranty .............................................................................................................................26

FOR EACH TYPE USER NOTICE

Class‘A’device

(Broadcast device for

business purpose)

This device is business purpose (Class‘A’) and seller or user should (Broadcast device for business purpose) be aware of it, and it is to use in other than home.

AOE-212N

AUDIO OVER ETHERNET

S3125A

Unpacking

Although your AOE-212N is neither complicated nor difficult to operate, we recommend you take a few minutes to read this brief manual and familiarize yourself with the important information regarding product features, setup and operation.

As with most electronic devices, we strongly recommend you retain the original packaging. In the unlikely event the product must be returned for servicing, the original packaging (or reasonable equivalent) is required.

Installation

Environment

Never place this product in an environment which could alter its performance or reduce its service life. Such environments usually include high levels of heat, dust, moisture, and vibration.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

S3125A

AOE-212N

Features

THE AOE AUDIO OVER ETHERNET NETWORK IS AN EASY TO USE SOLUTION FOR TRANSPORTING

AUDIOSIGNALS OVER ETHERNET TCP/IP BASED LOCAL AND WIDE AREA NETWORKS (LAN/WAN), AS WELL AS THE INTERNET.

- REAL TIME 2 CHANNEL AUDIO SIGNAL TRANSCEIVER (TRANSMITTER/RECEIVER)

ETHERNET TO 2CHANNEL ANALOG AUDIO SIGNAL REAL TIME TRANSMITTER, RECEIVER.

- FULL-DUPLEX DATA COMMUNICATION TO ETHERNET NETWORK.

CONTACT: FUNCTION OF IN/OUT CONTACT DATA TRANSCEIVER

(TRANSMITTER/RECEIVER). (EACH OF THE 8 CHANNELS)

COMMUNICATION: FUNCTION OF SERIAL DATA TRANSCEIVER

(TRANSMITTER/RECEIVER). (RS-232C, RS-422)

- EXPANSION OF DEVICE

MULTICAST (1:70) (THIS FUNCTION IS PLANNED TO UPGRADE) UNICAST (1:20) (THIS FUNCTION IS PLANNED TO UPGRADE)

AUDIO OVER ETHERNET

Composition and accessory

1. AOE-212N main set x1

2. AC power cord x 1

3. 3P terminal block x 4

4. 4P terminal block x 2

5. 16P terminal block x 2

6. RS-232C cable x 1

7. Rack mount screw x 4

8. Lan cable x 1

 Network setting

· AOE-212N SET can be set to dynamic IP, or static IP.

· AOE-212N SET use the 5454~5474 port, we need for 5454~5474 port is required for port forwarding or DMZ setting.

· Used under authorized to provide Internet service providers assign a static IP or dynamic IP in case of WAN network.

· LAN/WAN use is recommended to use a dedicated network configuration.

AOE-212N

AUDIO OVER ETHERNET

AOE-212N

AUDIO OVER ETHERNET

PHONES LEVEL

CH 1

CH 2

CH 1

DISP. MODE

CH 2 CH 1 CH 2

OUTPUT LINKINPUT

MONITOR OUTPUT

POWER

CH 1

CH 2

INPUT

4 5

ACT

192.168.1.202

Front Panel

1. MONITOR TERMINAL

Terminal monitoring the output signal of selected channel by using 3.5  earphone terminal.

2. MONITOR VOLUME

Control the monitor output volume.

3. MONITOR OUTPUT SWITCH

Switch selecting the desired channel output to monitor.

4. SIGNAL LED

LED displaying the input and output audio signals for each channel.

5. LINK / ACT

LED displaying the network status and data status of equipment.

6. LCD

LCD displaying the network (IP, Mac Address, S/W Version, etc.) settings and server connection status in the set.

7. DISPLAY SWITCH

Switch checking out the setting on the display. When the power switch is ON, the indicator will be it.

Display contents are as below.

1) Inter-M logo + IP Address

AOE-212N

2) MAC Address + Bandwidth + S/W Version

Inter-M:01:05:08 Ver. 1.0.0.1 TX: 3 kbps RX: 2 kbps

Audio Server On, 1 Client On

192.168.1.99

RS-232 Server Off Client Off

RS-422 Server Off Client Off

Cli

3) Audio state

(1) Sever on/off state (2) Sever on, Quantity of Client access device (3) Client on/off state (4) Accessed server IP

AUDIO OVER ETHERNET

4) RS-232 state

(1) Server on/off state (2) Client on/off state

5) RS-422 state

(1) Server on/off state (2) Client on/off state

6) PIO state

(1) Server on/off state (2) Client on/off state

8. Power LED

LED displaying the power supply status of set.

AOE-212N

AUDIO OVER ETHERNET

CONTACT OUTPUT

RS-232C

10/100M BASE-T

RS-422

RESET

AC INPUT 220V~ 60Hz

CH1

CH2 CH1 CH2

TX+TX RX+RX

MIN MAX

VOLUME VOLUME

MIN MAX

POWER

OFF ON

DC INPUT

24V

OUTPUT

INPUT

5 9

12345678

CONTACT INTPUT

12345678

Rear Panel

1. AC INLET

Terminal which inputs the AC power.

2. POWER SWITCH

Switch turning On/Off the AC Power.

3. DC INPUT TERMINAL

Backup battery(24DC) connecting terminal. In case of black out of AC power, connected backup battery supplies the power to the device. DC 24V input supplies the power to the set regardless of switch On/Off.

4. AUDIO OUTPUT TERMINAL

It consists of 2-channel with balance outputs (Hot, Cold, GND) with transmitted audio output terminal.

5. AUDIO INPUT TERMINAL

It consists of 2-channel with balance outputs (Hot, Cold, GND) with audio output terminal to be

transmitted.

6. AUDIO INPUT VOLUME

Control the volume of input audio signal. Control level is (-10dB ~ +10dB)

7. CONTACT POINT INPUT AND OUTPUT TERMINALS

If contact point signal is inserted in each contact point terminal of transmit AOE-212N device, contact point signal will be transmitted from the contact point output terminal of transmit AOE-212N device.

Output

Input contact point: Contact point signal can be inserted if pin of each channel is short. Output contact point: Same signals with input signal will be transmitted on the input contact point of transmitter.

AOE-212N

Input

AUDIO OVER ETHERNET

6000

ERIES

6000

ERIES

MAIN POINT

 Caution: Contact point signal is only transmitted when AOE-212N is operated under normal

conditions, and please input the signal after checking out the equipment operation status.

ecause data is transmitted in real times, signal will not be transmitted when device is off.

 Example: Connect the device to be controlled to the contact point terminal of AOE-212N from point

‘A’, and insert the control signal from the main building, then device of point ‘A’ can be controlled.

8. RS-232C/RS-422 communication terminal

Display the signals inserted in RS-232C or RS-422 terminal on the rear of AOE-212N on the RS-232C and RS-422 terminals of AOE-212N. For example, if signals, ‘A B C D’ are inserted in the transmitter, signals ‘A B C D’ will be displayed on the receiver.

RS-232C communication: No. 1 pin (Rx), No. 3 pin (Tx), No. 5 pin (GND) RS-422 communication: Tx+, Tx-, Rx+, Rx-

 Transmit and receive data communication using RS-232C/RS-422 ports supports 1:1

 Example: Connect the device to be controlled to the RS-232/RS-422 terminal of AOE-212 from

point ‘A’, and insert the control signal from the main building, then device of point ‘A’ can be controlled.

9. Network terminal

It is network connecting terminal (RJ-45) and supports 10/100 Base-Tx.

AOE-212N

AUDIO OVER ETHERNET

Equipment setting using AOE-212N internal CGI server

It provides the web-page to check the status and control of AOE-212N.

1. Accessing AOE-212N Web-page

1.1 Access to the web-page by using internet browser (Explorer, Chrome, FireFox, etc.)

1.2 Insert the IP address displayed on the front LCD of AOE-212N. If it is connected normally, user verification window will pop-up.

1.3 User verification is required to access the AOE-212N web-page.

Default value for factory setting is as below. User name: admin, password: 1(number).

 Please be sure to change the password after the connection you use.

2. Network Setup

Content Default Sample Value

MAC address Display the MAC address the device. 00:1D:1D:NN:NN:NN

Host name

IP address

IP address Setting a Static IP address 192.168.1.99

Subnet Mask Setting to the Subnet mask. 255.255.255.0

Gateway Setup the gateway of network connected to the gateway. 192.168.1.1

DNS 1 server Setup the address of DNS1 server. 168.126.63.1

DNS 2 server

Set

Clear Restore all setups to default values by using button

Displays the name of device. If it displays the location of device, management will be convenience. Text only (Incl. digits, no space) is applicable.

Setup the IP address of device. There are two ways“: Dynamic IP assignment from DHCP Server” and “Manual Setting”

Setup the address of DNS2 server. Follow the setup of property setup of device.

Apply and save the changed contents by using the

button after changing the setup of SET device.

aoe-212n

Manual Setting

168.126.63.2

AOE-212N

3. Audio Setup

AUDIO OVER ETHERNET

Content Default Value

Mode Setup the audio transmission mode. PCM, uni-cast

Audio Client Setup to receive the audio from another AOE-212N.

Port Setup the connecting port value to receive the audio. 5454

IP Address Setup the IP address to receive the server address audio. 192.168.1.99

Buffer rate The buffer rate is set according to the receiver's network. 3%

Run Check to activate audio receiving.

Audio sever Transmitting audio to other AOE-212N.

Sampling Rate Set the sample rate of the audio signal. 44100

INPUT CH 1 is selected; the sender channel 1 is transmitted to the receiver AOE-212N and

Channels

Port

Sever Address

Run

Set

is outputted on the receiver's CH1 audio output.

INPUT CH 2 is selected; the sender channel 2 is transmitted to the receiver AOE-212N and is

outputted on the receiver's CH2 audio output.ㅍ

Setup the connecting port value to transmit the port audio.

Set the server address for Multi-cast audio transmission mode.

Sets‘Run’to begin audio transmission. The equipment list of equipment being sent to the serial communication serial server run-time will be displayed.

Apply and save the changed contents by using the

button after changing the setup of SET device.

5454

224.124.0.1

Clear Restore all setups to default values by using button.

AOE-212N

AUDIO OVER ETHERNET

4. Serial Setup(232)

Content Default Value

Setting Setup the property of serial communication (RS-232C).

Baud Rate

Connection Connection setup to transmit the serial communication.

Port Default port value to transmit the serial communication. 5455

IP Address Setup the IP address to receive the serial communication. 192.168.1.99

Run Setup the Run of serial communication receiving.

Serial service Setup to transmit the serial communication to other AOE-212N.

Run

Set

Setup the communication speed of serial port. Scope is 2400bps~115200bps.

Sets ‘Run’ to begin serial communications transmission. The equipment list of equipment being sent to the serial communication serial server run-time will be displayed.

Apply and save the changed contents by using the

button after changing the setup of SET device.

9600

Clear Restore all setups to default values by using button.

AOE-212N

AUDIO OVER ETHERNET

- Serial Setup(422)

Content Default Value

Setting Setup the property of serial communication (RS-422) port.

Baud rate

Connection Connection setup to transmit the serial communication.

Port Default port value to transmit the serial communication. 5456

IP address Setup the IP address to receive the serial communication 192.168.1.99

Run Select ’Run’ to begin serial communication receiving.

Serial Service

Run

Set

Setup the communication speed of serial port. Scope is 2400bps~115200bps.

Setup to transmit the serial communication to an other AOE-212N.

Sets ‘Run’ to begin serial communications transmission. The equipment list of equipment being sent to the serial communication serial server run-time will be displayed.

Apply and save the changed contents by using the

button after changing the setup of SET device.

9600

Clear Restore all setups to default values by using button.

AOE-212N

AUDIO OVER ETHERNET

5. Data Setup

Content Default Value

Data Client Setup data transmit (Contact point).

Port Set the default data transmit port value. 5457

IP Address Setup the IP address to receive data. 192.168.1.99

Run Set ‘Run’ to activate data receiving.

Data Service Setup to transmit data to other AOE-212N.

Run

Set

Sets ‘Run’ to activate the data transmission. A list of

available data transmission equipment being will be displayed.

Apply and save the changed contents by using the

button after changing the setup of SET device.

Clear Restore all setups to default values by using button.

AOE-212N

6. SASS Setup

AUDIO OVER ETHERNET

Content Default Value

Enable/Disable Setup to enable/disable SASS. Disable

Server address

SASS Port Setup to SASS port. 1665

Audio Port Set the audio transmit port. 5454

Serial(232) port Set the serial (RS-232C) communication transmit port. 5455

Serial(422) port Set the serial (RS-422) communication transmit port. 5456

Data port Set the data transmit the port. 5457

Period for try Time period to access the server. Scope is 1~60 minutes. 5 minutes

Set

Clear Restore all setups to default values by using button.

Server address to update the information of device by using DDNS.

Apply and save the changed contents by using the

button after changing the setup of SET device.

None

AOE-212N

AUDIO OVER ETHERNET

7. Time Setup

Content Default Value

Time Zone Set the time in accordance with GMT. GMT+09:00

Current Time Current time in accordance with set GMT. 1970.01.01

Time Setup Setup the time for AOE-212N.

Manual Setup Setup the time manually by user.

Automatic time synchronization

GMT Change Change the GMT.

Set

If device is connected to internet, time can be synchronized automatically by using the time server.

Apply and save the changed contents by using the

button after changing the setup of SET device.

Time server address : Time.bora.net

AOE-212N

8. View Log

AUDIO OVER ETHERNET

Content Default Value

View Log

Delete Log

Check the system information such as setup of device and upgrade information, etc. Recorded information is recorded with time and date.

Press the delete log button to erase the log, the log records will be deleted.

AOE-212N

AUDIO OVER ETHERNET

9. Upgrade System

Content Default Value

Select the file to upgrade the AOE-212N.

Find File

SET

Select the file you want if file explorer is opened by pushing the

button next to the text box. Only *.tar‘file can be selected.

Upgrade the device after selecting the file

Go to next step if confirm is pushed.

It will take about 1 minute to upgrade the system. System will restart after upgrading.

AOE-212N

10. Restart System

AUDIO OVER ETHERNET

Content Default Value

Restart System Restart the device.

Set Restart the device by using the button.

AOE-212N

AUDIO OVER ETHERNET

11. Factory Set System

Content Default Value

Factory Set System

Set Restart the device by using the button.

Restore the device to factory setting. All information will be deleted.

AOE-212N

12. Password Change

AUDIO OVER ETHERNET

Content Default Value

Password Change

Set

Clear Restore all setups to default values by using button.

Change the administrator’s password.

Apply and save the changed contents by using the

button after changing the setup of SET device.

AOE-212N

AUDIO OVER ETHERNET

MAIN Point ‘A’

Point ‘B’

Point ‘C’

Audio Input

Serial Communication

Setting Program

Speaker

Amp

Device structure block

AOE-212N

How to connect

1 2345678

CONTACT OUTPUT

RS-232C

0/100M BASE-T

RS-422

RESET

AC INPUT 220V~ 60Hz

CH1

CH2 CH1 CH2

TX+TX RX+RX

IN MAX

VOLUME VOLUME

IN MAX

POWER

OFF ON

DC INPUT

24V

OUTPUT

NPUT

ONTACT INPUT

Contact input a

nd output

device

Serial Communication

device

RS-232C or RS-422

Amp and Speaker

Source device and Mixer

Network

switch

How to connect

AUDIO OVER ETHERNET

AOE-212N

AUDIO OVER ETHERNET

Head office

Branch

:LGH

College of

Engineering

College of

Humanities

College of

Arts

Gym

Disaster

Prevention Center

Headquart

Applications

Education institute, commercial facility, business facility, religion facility, gym, exhibition room, facility, leisure facility, them park, etc. 1:1 or 1: N functions are flexible to use in any space.

-1:1 Purpose

-1:20 (WAN network) and 1:64 (LAN) purpose (School, resort, theme park, exhibition room, museum, etc.)

AOE-212N

AUDIO OVER ETHERNET

Processor

Contact

(Output 8CH)

OLED Display

Audio Codec

AD DA

Audio Input

RS-232C

RS-422

Audio Ouput

Contact

(Input 8CH)

Ethernet

PHY

RJ-45

10/100

Base tx

Block Diagram

AOE-212N

AUDIO OVER ETHERNET

Specifications

AUDIO

Maximum Input Level

Maximum Output Level

Frequency characteristics

(48Khz Sampling, ± 1dB)

T.H.D (48Khz Sampling)

Support Sampling Frequency

Quantization bits

Data communication

Communication type

Contact Input, Output

Serial communication rate

ETHERNET(LAN)

General characteristics

Operating temperature

AOE-212N

+ 20 dBu

30Hz ~ 20kHz

0.1% (under)

16, 32, 44.1, 48Khz

24 bit

Contact, RS-232C, RS-422

Input 8-Channel, Output 8-Channel

2400 bps~115200 bps

10-100 Base-T, (RJ-45)

–10 ~ 40° C

100-120VAC or 220-240VAC:50/60Hz

Using Power

Power Consumption

Weight (SET)

Dimension (SET)

※Specification and performance is subject to be changed without notice.

※Signal propagation Latency CL2 Switch 1 via to audio : About 1sec/ Data: about 100ms / Contact : about 100ms

(Supplied AC mains transformer or DC 24V

depends on country requirements)

28W under

3.27kg/7.2lb

482(W)×44(H)×280(D)mm/18.9(W)×1.73(H)×3.14(D)in

AOE-212N

* Dimensions

482

280

440

AUDIO OVER ETHERNET

AOE-212N

AUDIO OVER ETHERNET

Service

Procedures

Take steps to insure the problem is not related to operator error or other products within the system. Information provided in the troubleshooting portion of this manual may help with this process. Once it is certain that the problem is related to the product contact your warranty provider as described in the warranty section of this manual.

Schematic

A Schematic is available by contacting your warranty provider.

Parts List

A Parts List is available by contacting your warranty provider.

Variations and Options

Variations

Products supplied through legitimate sources are compatible with local AC power requirements.

Options

No optional items are available for this product.

Warranty

Warranty terms and conditions vary by country and may not be the same for all products. Terms and conditions of warranty for a given product may be determined first by locating the appropriate country which the product was purchased in, then by locating the product type.

To obtain specific warranty information and available service locations contact Inter-M directly or the authorized Inter-M Distributor for your specific country or region.

AOE-212N

AUDIO OVER ETHERNET

NOTE

AUDIO OVER ETHERNET

AOE-212N

Inter-M, Ltd. (Korea) began operations in 1983.

Since then, Inter-M has grown to become one of the largest manufacturers of professional audio and commercial sound electronics equipment in the world.

Inter-M has gained worldwide recognition for its own branded products, as well as private label manufacturing of electronics sold under other names (OEM).

The company is no longer just a Korean company, but rather a global company that is truly international in scope, with factories and offices in Korea and China, and sales and marketing operations located in Japan, Europe, and the U.S.A.

With more than 850 employees around the globe, Inter-M is well-poised for further growth and expansion.

Inter-M Americas, INC.

13875 ARTESIA BLVD. CERRITOS, CA 90703 USA TEL : +1-562-921-0313, FAX : +1-562-921-0370 Home Page : http://www.inter-m.net, E-mail : info@inter-m.net

Inter-M Corporation

SEOUL OFFICE:653-5 BANGHAK-DONG, DOBONG-GU, SEOUL, KOREA TEL : +82-2-2289-8140~8, FAX : +82-2-2289-8149 Home Page : http://www.inter-m.com, E-mail : overseas@inter-m.com

MADE IMAN KOREA

June 2013 132449

Inter-M AOE-212N User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual