Interlogix UltraView ProBridge 2 User Manual
Calibur Kalatel KA2 ProBridge
Product Overview
& Installation Manual
Calibur Kalatel KA2 ProBridge 1 0150-0217B
Warning!
To prevent fire and electronic shock, do not expose this product to rain or moisture.
The lightning flash with the arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence of
uninsulated “dangerous voltage” within the
products enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point, within an equilateral
triangle, is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
!
Caution!
To prevent electric shock, do not remove cover. No user
serviceable components inside. Refer servicing to qualified
service personnel.
!
Caution! Electrostatic-Sensitive Device!
Use proper CMOS and MOSFET handing precautions, including approved
grounded wrists straps, etc., to avoid damage to this unit or its internal
components, from electric discharge.
Warning!
This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions in this manual, may cause
interference to radio communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to subpart J of part 15 of FCC rules which
are designed to provide reasonable protection against such interference when operated in
a commercial environment. This equipment has also been tested and found to comply with
the requirements for a CE Class A device and TUV safety standards.
Operation of this equipment in a residential area may cause interference, in which case the
user is required to take all measures that are necessary, at the user's expense, to correct
the interference.
Copyright Information
Software and/or firmware is furnished to the purchaser under a license for use on a single
system. Software and/or firmware included with this equipment are the sole proprietary
property of, confidential to, and copyrighted by Kalatel, Corvallis, Oregon, USA. The
software/firmware are not to be copied or disclosed in any manner without the express
written consent of Kalatel.
All information and specifications furnished by Kalatel are believed to be accurate and
reliable. No responsibility is assumed by Kalatel for neither its use nor any infringements of
rights of third parties that may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Kalatel.
The CALIBUR™ brand name and product model numbers are the property of Kalatel.
COPYRIGHT, 2002: The contents of this manual may not be copied or reproduced in any
manner or form without the prior written consent of Kalatel.
Calibur Kalatel KA2 ProBridge 2 0150-0217B
1 KA2 ProBridge ............................................................... 4
1.1 Kalatel KA2 ProBridge Description.....................................................4
1.2 Compatibility.....................................................................................4
1.3 Installation Environment ....................................................................4
1.4 Power...............................................................................................5
1.5 Installation Steps Summary...............................................................6
1.6 Connection Diagrams........................................................................7
2 Cable Specifications...................................................... 8
3 Troubleshooting............................................................. 9
4 Unit Settings ................................................................ 10
4.1 Configuring ProBridge Jumpers.......................................................10
5 Specifications .............................................................. 12
6 Appendix ...................................................................... 13
6.1 RS-485 Addressing and Connections ..............................................13
7 Using Calibur Keypads ................................................ 16
8 Warranty and Service .................................................. 17
8.1 Factory Service...............................................................................17
8.2 Warranty.........................................................................................17
Calibur Kalatel KA2 ProBridge 3 0150-0217B
1 KA2 ProBridge
1.1 Kalatel KA2 ProBridge Description
The Kalatel CBR-PB2-KA2 is a specific ProBridge unit for interfacing the DVMRe
family of digital video multiplex/recorders to Kalatel PTZ Cyberdomes where local
keyboard control is not already provided via a CBR-KB3 or KTD-405 keypad.
The CBR-PB2-KA2 combines into a single unit the services of both a CBR-PB2KAL and a KTD-410 previously required for all Cyberdome installations. Due to
all services being provided via a single unit this new configuration is less
expensive and easier to install.
1.2 Compatibility
The CBR-PB2-KA2 is compatible with all Calibur by Kalatel systems equipped
with RS-485 network capabilities except installations with a CBR-KB1 Keypad.
Compatible units include the Calibur DVMRe digital video units and various
Calibur Multiplexer models. Please check the specifications of the particular
Calibur product for RS-485 network support.
Kalatel Components:
(1) CBR-PB2-KA2 ProBridge. This product includes:
• (1) CBR-PB2-KA2 ProBridge unit.
• (1) P/N 4310-0034: RJ45 to RJ45 cable. Connects the ProBridge to
RS-485 Network. This cable is 6’ in length.
• (1) P/N 4310-0032A Cable from PB2 to Receiver/Dome
• (1) P/N 4010-0007: 12VDC 120VAC Power Supply or
(1) P/N 4010-0008: 12VDC 220VAC Power Supply.
• (1) P/N 0150-0217A: Product Overview and Installation Manual.
1.3 Installation Environment
Power: Ensure that the installation site’s AC power is stable and within the rated
voltage of the external power supply. If the site’s AC power is likely to have
spikes or dips, use power line conditioning or an Uninterruptible Power Supply.
Temperature: Observe the unit’s ambient temperature specifications when
choosing a location for the unit. Extremes of heat or cold beyond the specified
operating temperature limits may cause the unit to fail. Do not install this unit on
top of other hot equipment.
Moisture: Do not expose the unit to rain or moisture. Moisture can damage
internal components. Do not install this unit near sources of water.
RS485 Limitations: Total length of the RS-485 network is limited to 3000’.
Calibur Kalatel KA2 ProBridge 4 0150-0217B
1.4 Power
The ProBridge is furnished with a power supply (110 or 240 VAC). Do not use
any other power supply with this product. The manufacturer accepts no
responsibility for damage caused by the use of any other power supply.
Make sure installation is complete and all connections are made before applying
power to the unit.
4310-0007 120VAC Power Supply
Power Supply Input
Voltage: 120 Volt AC
Tolerance: ±10%
Frequency: 60 Hz
Power Supply Output
Voltage: 12 Volt DC
Current: 110mA
Power: 1.3 Watts
Connector: 2.1mm female barrel. Center Positive
4310-0008 220VAC Power Supply
Power Supply Input
Voltage: 220 Volt AC
Tolerance: ±10%
Frequency: 50 Hz
Power Supply Output
Voltage: 12 Volt DC
Current: 110mA
Power: 1.3 Watts
Connector: 2.1mm female barrel. Center Positive
Calibur Kalatel KA2 ProBridge 5 0150-0217B
1.5 Installation Steps Summary
Carefully and completely read the manuals for each piece of equipment
before attempting to install and connect this equipment.
Before you start connecting telemetry and other optional accessory
equipment to your system, make sure that all, power, video, VCR, and
monitor connections are completed, and everything is working correctly.
Wire the telemetry equipment according to that unit’s installation instruction.
Use the internal diagnostic testing capabilities of the telemetry receiver to
verify that the power and connections to the lens and motors are correct, and
function properly.
Using the Diagram on the following page, connect the equipment in the
following order:
1. Connect the CBR-PB2-KA2 to the Calibur unit (Multiplexer,
DVMRe, Triplex) via RS-485 port using the RJ-45 to RJ-45 cable.
The maximum total distance allowed on the RS-485 data line
(without signal amplification or modems) is 3,000 feet (1,000
meters). A 100-ohm terminator is required at each end of the
RS-485 line.
2. Supply power to the Calibur unit first and the CBR-PB2-KA2
second using the supplied AC to 12 VDC adapter. Via the Setup
Menus for the Calibur unit set the RS-485 network address to the
appropriate number (see the Appendix for RS-485 addressing).
3. Using the provided Cable connect from the ProBridge RCVR/DRVR
port to the Kalatel PTZ Interface card provided with the Cyberdome.
See the receiver's (PTZ) installation manual for more detailed
wiring instructions.
4. Set the ID addresses for the Receivers and Domes according to the
table later in this manual.
5. Via a networked connected PC with WaveReader software,
connect to the DVMRe unit and confirm proper control and
operation of the PTZ unit.
Calibur Kalatel KA2 ProBridge 6 0150-0217B
Loading...