Interlogix TVW-2101 User Manual

TruVision Analog Wedge Camera User Manual

P/N 1072656A-EN • REV 1.0 • ISS 25SEP13

Trademarks and

Manufacturer

Certification

FCC compliance

ACMA compliance

European Union

directives

Contact information

The TruVision name and logo are trademarks of United Technologies.

Other trade names used in this document may be trademarks or registered

patents

trademarks of the manufacturers or vendors of the respective products.

UTC Fire & Security Americas Corporation, Inc. 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative: UTC Fire & Security B.V. Kelvinstraat 7, 6003 DH Weert, The Netherlands

N4131

Class B: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Notice! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

This Class A digital apparatus complies with Canadian ICES-003.

Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du Canada.

12004/108/EC (EMC directive): Hereby, UTC Fire & Security declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC.

2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.

Content

Introduction 3

Product overview 3 Features 3

Installation 4

Installation environment 4 Package contents 4 Cable requirements 5 Camera description 5 Setting up the camera 6 Connecting the devices 6 Mounting the wedge camera 6 Configuring the wedge camera 8 Exposure 8 White Balance (WB) 9 Day and Night 9 Video Setup 10 Function Setup 11 Reset 11 Save & Exit 12

Specifications 12

OSD Menu Tree 12

Introduction

Product overview

This is the installation guide for TruVision analog wedge camera models:

 TVW-2101

 TVW-4101

Features

This section describes the camera features.

 Adopt high-performance sensor, 700TVL resolution, providing high definition

and clear image

 IR cut filter realizes day/night surveillance

TruVision Analog Wedge Camera 3

 Auto-white balance with high color rendition

 Auto electronic shutter control to adapt to the different surveillance

environments

 Auto gain control, adaptive brightness

 High SNR

 Environmental rating IP66

Installation

This chapter provides information on how to install the cameras.

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be done by qualified service personnel. Always use a 12 VDC UL listed Class 2 or CE certified power supply to power the camera, Do not overload the power cord or adapter.

• Ventilation: Ensure that the location planned for the installation of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the specified temperature, humidity or power source ratings. The operating temperature of the camera is between -40 to +60°C.

• Moisture: Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately if the camera is wet and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock.

• Servicing: Do not attempt to service this camera yourself. Any attempt to dismantle or remove the covers from this product will invalidate the warranty and may also result in serious injury. Refer all servicing to qualified service personnel.

• Cleaning: Do not touch the sensor modules with fingers. If cleaning is necessary, use a clean cloth with some ethanol and wipe the camera gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensors from dirt.

Package contents

Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit; contact the supplier immediately. If the unit is returned, it must be shipped back in its original packaging.

4 TruVision Analog Wedge Camera

+ 8 hidden pages