Interlogix TVP-2403 User Manual

TruVision HD-TVI Series 4
PTZ Dome Camera
Configuration Manual

P/N 1073207-EN • REV C • ISS 03FEB17

Copyright

©

2017 United Technologies Corporation.

Interlogix is part of UTC

, a unit of United

Technologies Corporation.

Trademarks and

patents

Trade names used in this document may be trademarks or registered
trademarks of the manufacturers or vendors of the respective
products.

Manufacturer

Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626

Authorized EU manufacturing representative:
UTC Building & Industrial Systems B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

Contact information

For contact
www.utcfssecurityproducts.eu

Climate, Controls & Security

All rights reserved.

-5923, USA

information, see www.interlogix.com or

.

Content

Introduction 2

Programming 3

Call up the camera OSD menu 3

Menu tree 4
Configuration 5

System Info 5
Dome Settings 5

HD-TVI 1080P Non-IR Dome Camer as 2
HD-TVI 1080P IR Dome Cameras 2

System Settings 5
Camera Settings 8
Motion Parameter 11
Presets 12
Preset Tour 13
Timing Task 14
Shadow Tour 15
Privacy Mask 15
Alarm Input 16
Alarm Output 18
Clear Settings 18
Zones 18
Video Setting 19

IR Parameter 19
Restore Camera 20
Restore Settings 20
Reboot Dome 20
Language 20

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 1

Introduction

This is the configuration manual for following camera models:

HD-TVI 1080P Non-IR Dome Cameras

 TVP-2401 (30X, Pendant /Wall mount, PAL)
 TVP-2402 (30X, Surface/Flush mount, PAL)
 TVP-4401 (30X, Pendant /Wall mount, NTSC)
 TVP-4402 (30X, Surface/Flush mount, NTSC)

HD-TVI 1080P IR Dome Cameras

 TVP-2403 (30X, Pendant/Wall mount, IR, PAL)
 TVP-4403 (30X, Pendant/Wall mount, IR, NTSC)

2 TruVision HD-TVI Series 4 PTZ Dom e Camera Configuration Manual

Programming

Once the camera hardware has been installed, the camera can be configured
using a HD-TVI DVR menu.

You can also configure the camera settings via a DVR. Select the PTZ protocol

TruVision Coax and click the menu button to call up the menu.

Call up the camera OSD menu

To set up the camera:

1. Set up the camera hardware as described in the installation man ual .

2. Under Camera Settings of the DVR, access the PTZ menu and set the
protocol for the TruVisi on HD-TVI camera to TruVision-Coax.

Note: The TruVision-Coax protocol will always be enabled.

3. In live view of the desired camera, click the PTZ Control icon on the live view
toolbar to access the PTZ control panel.

4. To call up the camera setup menu:
From the camera, press the Menu button (if present).
— or —
From the local live view of the DVR, select Menu from the PTZ control panel

or call Preset 95.
— or —
From the remote live view of the DVR, call Preset 95.
The camera setup menu appears (see “Menu tree” on page 4 for the menu

structure).

5. Select the menu options:
From the DVR: To select an OSD item, click the directional buttons up/down.

To adjust the value of a selected item, click the directional buttons left/right.
From the camera (if it has a Menu button): To select an OSD item, push

the Menu button up/down. To adjust the value of a selected item, push the
Menu button left/right.

6. Click Iris+ to enter the submenu or to confirm the selected item.

7. When the setup is complete, select Exit and click Iris+ to exit the camera
OSD.

Note: You cannot exit the camera setup menu using the Menu button on the
camera.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 3

Menu tree

The menu tree of the TruVision 1080P HD-TVI PTZ domes is shown below.

4 TruVision HD-TVI Series 4 PTZ Dom e Camera Configuration Manual

Configuration

This section describes how to set up the menu settings.

System Info

Display the current system information of the PTZ do me, incl udi ng mod el,
address, protocol, etc.

Note:

 Information on this menu cannot be edited.
 The temperature refers to the internal temperature of the PTZ dome.

Dome Settings

System Settings

You can check and edit the system information of the software address, baud
rate, system time, etc. on the system information settings menu.

Note: Click the left and right directional button s in the PTZ control panel via the
web browser of the encoder to enter the next page and return to the previous
page of the submenu if more than one page is available.

Note: As TruVision recorders do not support an address greater than 255, a soft
address greater than 255 will not support any protocol even though the camera
supports 8190 for UTC-RS485 (Interlogix-Protocol) and 512 for DIGIPLEX and
ASCII. However, you can have an address greater than 255 for legacy products
that supports UTC-RS-485 (Interlogix-Protocol), DIGIPLEX or ASCII.

SOFT ADDRESS This is the address to connect and control the HD-TVI PTZ dome. It

can be used as an alternative to the hard address if, for example, the
address must be above the avai lab le hard addres s .

SET SOFT

ADDRESS

SOFT BAUDRATE This is the valid baud rate for the HD-TVI PTZ dome with the soft

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 5

ON: The soft address is the valid address for the HD-TVI PTZ dome.

The selectable soft address range is from 1 to 255.

OFF: This refers to the hard address. Use the DIP switch to set the

valid address for the HD-TVI PTZ dome.

address.

Y - M - D 12 12 12

H - M - S 15 33 25

DONE : OPEN

QUIT : CLOSE

DISPLAY SETTINGS

ZOOM RATIO ON

P/T ANGLE ON

ALARM

OFF

TIME

ON

PRESET

LABEL

ON

ZONE OFF

ADDRESS OFF

BACK EXIT

DISPLAY SETTINGS

ERROR RATE OFF

FAN/HEAT OFF

BACK EXIT

SET SOFT BAUD ON: The soft baud rate is the valid baud rate for the HD-TVI PTZ

dome. Select 2400, 4800, 9600 or 19200.

OFF: Use the DIP switch to set the baud rate.

BROADCAST

ADDR
PELCO This is used for Pelco-P and Pelco-D protocols.

When set to ON, the control device with address 0 can control all
domes connected to it.

If the video

freezes, set PELCO to ON to improve the video quality.

SYSTEM TIME 1. Move the cursor to SYS TIME using the directional buttons

and click IRIS+ to enter.

2. Click the left/right directional buttons to position the cursor on
the specific item (year/month/day or hour/minute/second) of
which you want to change the value.

3. Click the up/down directional buttons to increase/decrease the
value.

4. Click IRIS+ button to confirm the settings and exit.

ANGLE ZERO Define the angle zero of the PTZ dome.

DISPLAY

SETTINGS

ZOOM RATIO ON: Enable the on screen display of zoom

6 TruVision HD-TVI Series 4 PTZ Dom e Camera Configuration Manual

Angle zero is when the PT position of the dome is 0,0. Use this
function to set the angle zero.

Enable or disable the on-screen display of PTZ movements, alarms,
time, presets, zone, address, error rate, and fan/heat show, etc.

ratio.

OFF: Disable the on screen display of zoom

ratio.

2: The ZOOM RATIO will display on screen for

2 seconds.

5: The ZOOM RATIO will display on screen for

5 seconds.

10: The ZOOM RATIO will display on screen

for 10 seconds.

P/T ANGLE ON: Enable the on screen display of P/T angle.

OFF: Disable the on screen display of P/T

angle.

2: The P/T angle will display on screen for 2

seconds.

5: The P/T angle will display on screen for 5

seconds.

10: The P/T angle will display on screen for 10

seconds.

ALARM ON: Enable the on screen display of alarm

message.

OFF: Disable the on screen display of alarm

message.

TIME ON: Enable the on screen display of zoom

ratio.

OFF: Disable the on screen display of zoom

ratio.

PRESET LABEL ON: Enable the on screen display of preset

label.

OFF: Disable the on screen display of preset

label.

2: The PRESET LABEL will display on screen

for 2 seconds.

5: The PRESET LABEL will display on screen

for 5 seconds.

10: The PRESET LABEL will display on screen

for 10 seconds.

ZONE ON: Enable the on screen display of zone.

OFF: Disable the on screen display of zone.

ADDRESS ON: Enable the on screen display of camera

address.

OFF: Disable the on screen display of camera

address.

ERROR RATE ON: Enable the on screen display of error rate.

OFF: Disable the on screen display of error

rate.

FAN/HEAT ON: Enable the on screen display of fan/heater

message.

OFF: Disable the on screen display of

fan/heater message.

HEAT CONTROL TEMP: The heater is contr olled b y the tem per ature.

ON: Enable the heater.
OFF: Disable the heater.
N/A: Only for non-IR PT Z .

FAN CONTROL TEMP: The fan is controlled by the temperature.

ON: Enable the fan.
OFF: Disable the fan.

EIS SETTINGS ON: Enable the Electronic Image Stabilization.

OFF: Disable the Electronic Image Stabilization.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 7

CAMERA

GAIN LIMIT 15

DEFOG OFF

INIT LENS OFF

BACK EXIT

PRESET FOCUS ON: Enable the preset direct focus function to also record the focus

(F) value.

OFF: Disable the preset direct focus function.

PROTOCOL

ENABLE

ON: The user-defined protocol is enabled.
OFF: The user-defined prot ocol is disa ble d.

PROTOCOL Define the protocol: UTC RS-485, PELCO-P, PELCO-D, DIGIPLEX,

or ASCII.

485 CHECK Set to ON or AUTO for automatic RS-485 configuration diagnosis.

If the configuration is incorrect, an alert will be received. If you set the
value as AUTO, it will automatically stop the diagnosis when no
errors exist.

MEMORY TIME The dome resumes its previous PTZ status when it restarts after a

power-off and had stopped at the position longer than the predefined
time. Set the memory time to 10s, 30s, 60s, 180s, or 300s.

NEAR FOCUS

LEVEL

This is a debug interface. It ranges from 0 to 2. Select one level to
have the optimal focus speed and accuracy depending on the actual
scenario.

Camera Settings

You can set the camera parameters including focus, shutter speed, iris, etc.

FOCUS Set the focus mode.

AF (Autofocus): The lens remains in focus during PTZ movements.
MF (Manual Focus): Manually adjust the focus us ing t he Focus+ and

Focus- buttons.

HAF (Half-autofocus): The PTZ dome only focuses automatically

once after panning, tilting and zooming.
Note: The focus mode needs to be changed to MF before controlling

Focus in the PTZ panel.

8 TruVision HD-TVI Series 4 PTZ Dom e Camera Configuration Manual

The higher you set the SHUTTER value (a faster shutter speed), the

ZOOM LIMIT Set the user-defined limitation of the zoom amount. Zoom amount =

Optical zoom× Digita l zoom.
If you set the zoom limit to its minimum value (22), digital zoom is

disabled and optical zoom is at maximum value. If you set a lower
zoom limit, digital zoom is enabled.

ZOOM SPEED Define the speed at which the lens changes from wi d e to the optical

zoom.

SLOW SHUTTER This extends the exposure time under low light conditions in order to

obtain a clearer image. It can be set from 0 to 5 and the higher the
value is, the longer the exposure time.

DAY/NIGHT Set the value to AUTO, DAY or NIGHT.

AUTO: The PTZ dome automatically switches from Black and White

mode (NIGHT) and Color mode (DAY) depending on the light
conditions. This is default mode.

NIGHT (B/W): Switch the IR cut filter to Black and White mode to

increase the lens sensitivity in low light conditions

DAY (Color): Switch to Day mode in normal light conditions.

Note:

 Set the DAY/NIGHT values in this menu. Call up preset 39 to set

the IR cut filter mode to DAY mode and call up preset 40 to set it
to NIGHT mode.

 The DAY/NIGHT values cannot be configured unless the IR

function is disabled.

D/N LEVEL This is the light level for auto D/N mode switch.

The IR cut filter switches between DAY and NIGHT mode when the
light conditions reach this user-defined D/N sensitivity level.

SHARPNESS

This function increases the image gain and sharpens the edges in the
image to enhance image details.

Set the sharpness level between 0 and 15.
BLC/WDR Set the value as ON or OFF to enable or disable the functions.
EXP MODE AUTO: Auto iris, auto shutter and auto gain. The PTZ dome

automatically adjusts the values depending on the light conditions.

This is default mode.

IRIS: User-defined iris value, auto shutter and auto gain. It is the iris-

priority mode. Define the iris value in the IRIS, SHUTTER and GAIN

menus (see below).

SHUTTER: User-defined shutter speed, auto iris and auto gain. It is

the shutter-priority mode. Define the shutter speed in the IRIS,

SHUTTER and GAIN menus (see below).

MANUAL: User-defined iris, gain and shutter. in t he IRIS, SHUTTER

and GAIN menus (see below).
IRIS It measures the amount of light entering to the lens. You can s et the

iris value from 0 to 17 in response to the changing light conditions.

The EXP MODE needs to be changed to MANUAL before controlling

the Iris in the PTZ panel.

Note: Iris is fully closed at 0 and fully open at 17.
SHUTTER The speed of the electronic shutter controls the amount of light

entering to the lens in a unit of time (a second). You can manually

configure the shutter speed for the PTZ dome. You can also enable a

slow shutter function for low light conditions.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 9

lower the amount of light entering per second, and the darker the

image. Set the value to 1, 2, 4, 8, 15, 30, 50, 125, 180, 250, 500,
1000, 2000, 4000 or 10000.

Note: The value of X indicates that the shutter speed is 1/X second.

GAIN Gain value: The gain value is the amplification degree of the original

image signal. Set the value between 0 and 15.

Gain limit: The higher gain value set, the more noise will appear in

the image. You can set the maximum gain value between 0 and 15 to
limit the gain range and control the noise in the image.

Note: Change DAY/NIGHT mode to DAY or NIGHT mode, and set
the EXP MODE as MANUAL before adjusting the gain value.

EXPOSURE COMP Adjust this value to increase the brightness of the image.

Set the EXPOSURE COMP value between 0 and 14. Default value is

7.

WB MODE Set the WHITE BALANCE MODE as AUTO, INDOOR, OUTDOOR,

SELFDEF (self-defined), ATW (auto-tracking) or HAUTO (half-auto).

AUTO: The dome automatically retains color balance according to

the current color temperature.

INDOOR, OUTDOOR: These two modes are for indoor use and

outdoor use respectively.

SELFDEF: Adjust the color temperature manually.

Note: In SELFDEF mode, you need to adjust the RED and BLUE

values manually.

ATW: In auto-tracking mode, white balance is continuously being

adjusted in real-time according to the color temperature of the scene
illumination.

HAUTO: Select this mode so that the viewed image automatically

retains color balance depending on the current color temperature.

RED It is used to adjust the red value when choosing SELFDEF for

WHITE BALANCE and it can be set from 0 to 255.

BLUE It is used to adjust the blue value when choosing SELFDEF for

WHITE BALANCE and it can be set from 0 to 255.

IMAGE FLIP When enabled, the image is flipped diagonally along its central axis

to obtain a mirror reflection of the image.

FOCUS LIMIT Set the minimum focus distance.

Configure the focus limit at a longer distance when the tar get is far
away to avoid the PTZ dome focusing on objects close to it, or
configure a shorter distance when the target is close to the PTZ
dome so it does not focus on further away objects.

Set FOCUS LIMIT to 1cm, 30cm, 1m, 3m, 5m or AUTO to make sure
that the PTZ dome focuses on the target.

Note: If you test the PTZ indoors the camera may not focus when
zooming at high ratio. Please adjust this parameter to a lower value.

2D DNR ON: The larger the value, the less the noise there will be in low light

conditions.

OFF: Disable the function.

3D DNR ON: The larger the value, the less the noise there will be in low light

conditions.

OFF: Disable the function.

MINI ZOOM LIMIT Set the minimum zoom of the lens.

10 TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual

Note: This function is not supported by all PTZ dome cameras.

CHROMA

SUPPRESS

ON: Suppress color noise to obtain clear and high-qualit y im ag es in

low light conditions.

OFF: Disable the function.

SATURATION Saturation indicates the brightness of the color. The higher the

saturation, the brighter the color.
CONTRAST Contrast is the degree of difference between the darker and lighter

parts of the image.
SCENE MODE Select the scene mode as INDOOR or OUTDOOR. The default

image settings change depending on the selected scene mode.
HLC Use this highlight compensation function to compensate for areas

with strong spots of light in order to produce clearer images.

Set the value to brighten the darker area and weaken the highlight

area of the image. The larger the value selected, the stronger the

effect.
SHARPNESS

COMP

Set the value to automatically adjust the sharpness of the image to

get a clear image. The larger the value selected, the stronger the

effect.
GAIN LIMIT The higher gain value you set, the more noise will appear in the

image. Set the maximum gain value between 0 and 15 to limit the

gain range and control the noise in the image.
DEFOG Enable this function to improve an image’s visibility and clarity in

foggy weather.
INIT LENS Enable this function to automatically initialize the lens to ensure

normal operation.

Motion Parameter

AUTO FLIP In manual tracking mode, the dome automatically rotates 180

degrees horizontally when a target object passes directly under the

PTZ dome for uninterrupted tracking.

Note: AUTO-FLIP is set to ON by default. It is not user-definable.
PROPORTIONAL

PAN

Use this function to change the pan/tilt speed according to the

amount of zoom. When there is a large amount of zoom, the pan/tilt

speed will be slower to prevent the image from moving too quickly in

live view.

Set to ON or OFF to enable/disable the function.

Note: This function is enabled automatically while setting a shadow

tour.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 11

PARK TIME This is a period of inactivity after which the PTZ dome automatically

starts a predefined action. Set it between 5 and 720 seconds.

PARK This is a predefined action. It can be set as presets 1-8, shadow tours

1-5, preset tours1-10, pan scan, tilt scan, panoramic scan, day mode,
night mode or none.

Note: If no control signal is received after the park time under the
following situations, no park action is performed:

- When performing dome actions by calling special presets; or,

- When performing external alarm linkage actions.

SCAN SPEED The scan speed defines the scan degree per second of pan scan, tilt

scan, and panoramic scan.
Select a scan speed between 1 and 40. The larger the value, the

faster the scan speed.

IMAGE FREEZE Use this feature to directly switch from live view of the current scene

to another scene that is defined by a preset without showing the
areas between these two scenes. It reduces the bandwidth usage in
a digital network system and also provides privacy protection for the

areas between the two scenes displayed.
DOME SPEED Manually set the dome speed between 1 and 10.
PRESET SPEED Set the speed to call up a preset between1 and 8. The larger the

value, the faster the speed to call up a preset.
ENABLE LIMIT These are user-configurable positions that limit the panning and tilting

area of the PTZ dome. Set the left, right, up and down limits to define

an area.

ON: This feature is enabled.

OFF: This feature is disabled.

LIMIT SETTINGS Set prompts to set the left, right, up and down limits from the menu.
CLEAR LIMITS Clear the limit setting.

SET ELEVATION ON: Enable to increase the elevation angle range of the PTZ dome.

OFF: Disable the function.

Note: The range of the elevation angle is 0 to 90° by default. It

changes to between -15° and 90° when SET ELEVATION is enabled.

Presets

A preset is a user-defined monitoring position/point. You can call up the preset
number to change the current monitor scene to the defined position.

PRESET NO. Select the preset number from between 1 and 256.
<UNDEFINED> This is the preset label.

12 TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual

If the preset has been defined, the preset label is displayed under the

NUM PST DWELL SPD

1 0 6 30

2 0 6 30

3 0 6 30

4 0 6 30

5 0 6 30

6 0 6 30

7 0 6 30

DONE : OPEN QUIT : CLOSE

number. If it has not been defined, UNDEFINED is displayed under

the number.
SET PRESET Set the desired scene/position of the preset.
CLEAR Clear the preset settings.

Preset Tour

A sequence of user-defined presets stored in the system memory and recalled
when required, either upon an al ar m tr igger, when programmed, or o n manual
recall.

PRESET TOUR

Select a preset tour number between 1 and 10.

NO.
EDIT PRESET

TOUR

Enter edit mode. The menu is shown below.

Click the left/r ight direc t ion al buttons to position the cursor in the

PRESET, DWELL and SPD columns.

Click the up/down directional buttons to set the value of the preset

number, dwell time and patrol speed.

Note: The presets used in a patrol must be pre-defined. The dwell

time is a preset amount of time a camera image is displayed before

the camera moves to the next preset position. It is the camera's

inactive time. Select a dwell time value between 0 to 800 seconds,

which is divided into 30 lev els. The patrol speed is the scanning

speed the PTZ dome to switch between the presets. Select a patrol

PREVIEW Preview the current patrol.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 13

speed value between1 and 40.

WEEK WHOLE WEEK

START(H-M) 00 00

END(H-M) 00 00

DONE : OPEN

QUIT : CLOSE

CLEAR PRESET

Delete the current patrol.

TOUR

PRESET TOUR-D This is the time to switch from one preset to another. Select 5 s, 10 s,

20 s, 30 s, or 60 s.

Timing Task

A timing task is a preconfigured action that can be performed automatically at a
specific date and time.

TASK NO. Select a task number between 1 and 8.
ENABLE TASK ON: Enable the task.

OFF: Disable the task.

ACTION Select a task from preset 1 to 8, shadow tour 1 to 5, preset your 1 to

10, pan scan, tilt scan, panoramic scan, day mode, night mode, zero
calibrate and none.

TASK TIME Click the left and right directional buttons to position the cursor at

WEEK, START (H-M) and END (H-M).

Click the up and down directional buttons to set the start and end
times to run the time task.

Note: The weekday can be set to be from Monday to Sunday or

Whole Week; H refers to Hour and M refers to Minute.

TASK PREVIEW Preview the current task.
TASK CLEAR Delete all the defined tasks.

14 TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual

REMAIN MEMORY 100

DONE : OPEN

QUIT : CLOSE

Shadow Tour

A shadow tour is a recording of a user-defined movement of a P TZ dom e
camera. A shadow tour can be stored and replayed.

SHADOW TOUR

NO.

EDIT SHADOW

TOUR

PREVIEW Preview the current shadow tour.
CLEAR SHADOW

TOUR

Select a shadow tour number between 1 and 5.

Use this menu to record a shadow tour.

Click the PTZ control and directional buttons to operate the PTZ

dome to draw a path, including pan scan, tilt scan, zoom in, zoom

out, etc. The PTZ dome automatically memorizes the path as a

shadow tour.

Note: The pan/tilt movements and the lens operations cannot be

simultaneously memorized.

Delete all the defined shadow tours.

REMAINING This shows the remaining memory of the PTZ dome to configure

shadow tours. When it reaches 0, no more shadow tours can be

configured.

Privacy Mask

This is a visual block or masked area that is configured to conceal the view in
designated areas. For example, blocking out neighboring windows to protect
them from being viewed and/or recorded.

The masked areas can move with the pan/tilt movements and automatically
adjust in size as the lens zooms in and out.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 15

ADJUST MASK POS

FOCUS SHIFT STATUS

SAVE : OPEN

QUIT : CLOSE

Note: Occasionally portions of the masked area may be visible when quick pan­tilt-zoom commands are executed. It is recommended that privacy mask regions
are configured to extend past the boundaries of the protected area to avoid
inadvertent exposur e.

MASK NO. The privacy mask number, which ranges from 1 to 24.
MASK STAT US ON: Enable the privacy mask function.

OFF: Disable the privacy mask function.

SET MASK Click this menu option to enter the editing mode (see below).

ADJUST MASK POS: Use this function to position the mask on

screen. Click the directional buttons to move the privacy mask to the
desired area. Click the FOCUS+ button to call up the ADJUST MASK
SIZE message on screen. Click the up/down buttons to
increase/decrease the height of the mask and click right/left buttons
to increase/decrease the width of the mask.

Note: The tilt range to configure privacy masks is between 0° and
70°.

SAVE: Click to save changes and return to the previous menu. The

masked area turns gray. To modify the mask, click IRIS+ to enter the

SET MASK menu. Click IRIS+ button again to edit.
QUIT: Cancel.

CLEAR MASK Delete all privacy masks.

Alarm Input

You can configure the PTZ dome to respond to alarm events with alarm linked
actions, such as calling presets, preset tours , shadow tours, scanning, etc.

16 TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual

ALARM INPUT

RESUME ON

SEQUENCE 5

DELAY TIME 5

ALARM SETTING

BACK EXIT

RESUME ON: Enable the PTZ dome to resume its previous activity after the

triggered actions finished.

OFF: Disable the PTZ dome to resume its previous activity after the

triggered actions finished.

Note:

 If the PTZ dome is moving when a linkage action is triggered, it

will stop at the current position and resume from this position
after the linkage action finishes.

 The PTZ dome can be configured to resume the PTZ positions,

focus and iris value.

SEQUENCE This is a user-defined interval after which the PTZ dome will respond

DELAY TIME If a linkage action has already been triggered by an alarm input, the

ALARM

SETTING

to one alarm first and then to the next one when more than one
alarm of the same priority occurs at the same time. Set a value
between 1 and 200 seconds.

PTZ dome only responds to the input from the same channel after a
user-defined reset delay time.

This is the rest time that the PTZ dome considers an alarm to be
active when it is physicall y cleared. Set a value between 0 and 300
seconds.

ALARM NO.: The alarm number up to 2.
PRIORITY: Set it as HIGH, MEDIUM or LOW. If multiple alarms with

different priorities are triggered at the same time, the dome only
responds to the alarm with the highest priority. If multiple alarms with
the same priority are triggered at the same time, then the dome will
respond to each alarm according to the defined alarm sequence.

LINK: It can be set as preset from 1 to 8, shadow tour from 1 to 5,

preset tour from 1 to 10, panning scan, tilting scan, panor amic scan,
day mode, night mode or none when an alarm occurs.

ALARM OUTPUT: Choose NONE to disable alarm outputs or

choose 1 to active ALARM OUTPUT 1.
Note: There is 1 alarm output configurable; configuring the alarm

output 2 will be invalid.

ALARM INPUT: Set the input status to OPEN (Normally open),

CLOSE (Normally closed) or OFF (disable the alarm input).
Note: If you set the status as OPEN, the alarm will be triggered by

high current level. If you set the status as CLOSE, the alarm will be
triggered by low current level. If you set the status as OFF, it will be
triggered when this input channel is disabled.

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 17

ALARM SETTING

ALARM NO. 1

PRIORITY HIGH

LINK NONE

ALARM OUTPUT NONE

ALARM INPUT OPEN

BACK EXIT

Alarm Output

An alarm output is a configurable alarm output interface on the PTZ dome back
box which can connect and trigger another alarm device to operate.

ALARM OUTPUT Set the alarm output type as OPEN (normally

open) or CLOSE (normally closed).
Note: Only one alarm output can be configured.

The second alarm output cannot be configured.

OUTPUT1, OUTPUT2 OPEN: Set the alarm output to normally open.

CLOSE: Set the alarm output to normally closed.

DWELL TIME This is the duration of the alarm output signal. Set

the value between 0 and 60 seconds.

Clear Settings

PRESETS
PRESET TOURS  Clear all the settings of preset tours
SHADOW

TOURS
MASKS  Clear all the settings of masks.
ZONES  Clear all the settings of zones.
TIME TASKS Clear all the settings of timing tasks.

 Clear all the settings of presets.

 Clear all the settings of shadow tours

Zones

A zone is a panning and tilting area defined by left/right limits. You can configure
the zones in the ZONES submenu. Define a zone when the targeted surveillance
scene is limited.

18 TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual

IR PARAMETER

IR SENSITIVITY MEDIUM

N/M LED CURRENT 8

FAR LED CURRENT 8

REFERENCE ZOOM 2

LED CONTROL AUTO

SWITCH DELAY(S) 2

SMART IR 0

BACK EXIT

ZONE NO. Select a zone number ranging between 1 and 8.
<UNDEFINED> This is the zone label.

If the zone has been defined, the zone label is displayed
under the number. If it has not been defined,

UNDEFINED is displayed under the number.
EDIT ZONE Follow the prompts to set the left and right limits.
ZONE STATUS This shows the current status of the zone.
SCAN STATUS ON: Enable zone scanning.

OFF: Disable zone scanning.

CLEAR ZONE Clear the zone settings.

Video Setting

Modify the video output standard, including resolution and frame rate, as desired.

IR Parameter

You can configure the IR parameters including the IR sensitivity, N/M LED
current as well as LED control, etc.

Note: The IR parameter settings are supported by IR PTZ domes only.

IR SENSITIVITY Set the sensitivity of the IR LED to HIGH, MEDIUM or LOW.
N/M LED

CURRENT

FAR LED

CURRENT

REFERENCE

ZOOM

TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual 19

Select the current of the near/middle IR LED from between 1 to 10.

Select the current of the far IR LED from between 1 to 10.

When the actual zoom rate is greater than the zoom limit, the IR
switches to long-distance IR LED.

When the zoom rate is less than the zoom limit, the IR switches to

the near/medium-distance IR LED.

LED CONTROL Set the LED control. Select one of the options:

ALL ON: Enable all IR LEDs
FAR ON: Enable long-distance IR LEDs
NEAR ON: Enable near/medium -distance IR LEDs
AUTO: Enable IR LED automatically depending on the light

conditions

ICR: Adjust the IR LED working mode according to the ICR (infrared

cut filter)

CLOSE: Disable IR LEDs

SWITCH DELAY(S) This is the time delay in switching between long-distance IR LED and

N/M-distance IR LED.

SMART IR This function is implemented to decrease the over exposure of IR

light and it can be set from 0 to 15. The higher the value is, the higher
suppress level of IR o ver e x pos ure.

Restore Camera

Enter MAIN MENU > RESTORE CAMERA

Click IRIS+ to restore the camera settings to the default value, or click IRIS- to
exit.

Note: Camera settings include the image parameters, lens settings and display
settings.

Restore Settings

You can reset all dome settings to factory default parameters.
Note: Dome settings are mainly of PTZ parameters and alarm parameters. They

also include some system settings, such as the dome address.
Enter default dome setti ng s menu: MAIN MENUS > RESTORE DEFAULTS
Click IRIS+ to restore the dome settings to the default value or click IRIS- to exit.

Reboot Dome

Enter MAIN MENU > REBOOT DOME. Click IRIS+ to reboot the PTZ dome
remotely.

Language

Enter MAIN MENU > LANGUAGE. Click left or right to change the language and
click IRIS+ to confirm the language.

20 TruVision HD-TVI Series 4 PTZ Dome Camera Configuration Manual