Interlogix AR2000 User Manual

AT1000
AR2000 AT1000-R3 AT1020 AT1020-R3 AT1025 AT1025-R3 AR1000 AR1000-R3 AR1030 AR1030-R3
AR2000-R3
AR2020
AR2020-R3
AR2025
AR2025-R3
AR2010WDMA-R3
AR2010WDMB-R3
IFS Fiber Module Installation & Operation
P/N 1062858 • REV B • ISS 01JUL11
AT1000
AUDIO INPUT
AR1000
3 2 1
Ground Audio Input
Audio Input
6
AUDIO OUTPUT
NOTE:
For an unbalanced connection, tie pin 2 to pin 3 and utilize pins 2 and 3 for the audio input to the AT AR1000 Series module.
1000 Series module. Utalize pins 1 and 2 for the audio output from the
5 4
Ground Audio Output
Audio Output
AT1000
FM AUDIO TRANSMITTER
OPTICAL OUT
POWER
POWER
International Fiber
ifs
Systems Incorporated
POWER
*Note: For unbalanced audio input, use the following setup
Ground Audio Input
Audio Input
Tie together
}
AR1000
FM AUDIO TRANSCEIVER
GRD- 6 AUDIO OUT- 5 AUDIO OUT
GRD- 3
AUDIO IN- 2 AUDIO IN
12 VAC/12 VDC- 3
GRD- 2
12 VAC/12 VDC- 1
Simplex multimode fiber optic cable
Audio Output
- 4
- 1
}
Balanced
}
Audio Input*
Blue Green Brown
CARRIER
POWER
POWER
ifs
International Fiber Systems Incorporated
POWER
OPTICAL IN
GRD- 6 AUDIO OUT- 5 AUDIO OUT
GRD- 3
AUDIO IN- 2 AUDIO IN- 1
12 VAC/12 VDC- 3
GRD- 2
12 VAC/12 VDC- 1
Audio Output
- 4
}
Audio Input
}
Blue Green Brown
AR2000
AUDIO INPUT
6 5 4 3 2 1
Ground Audio Input Audio Input
6 5 4
AUDIO OUTPUT
NOTE:
For an unbalanced connection, tie pin 2 to pin 3 and utilize pins 1 and 2 for the audio input to the AR2000 Series module. Utalize pins 4 and 5 for the audio output from the AR2000 Series module.
3 2 1
Ground Audio Output
Audio Output
CARRIER
POWER
POWER
AR2000
FM AUDIO TRANSCEIVER
International Fiber
ifs
Systems Incorporated
POWER
OPTICAL IN
OPTICAL OUT
GRD- 6 AUDIO OUT- 5 AUDIO OUT
GRD
AUDIO IN AUDIO IN
12 VAC/12 VDC- 3
GRD- 2
12 VAC/12 VDC- 1
Audio Output
- 4
- 3
- 2
- 1
}
Balanced
}
Audio Input*
Blue Green Brown
CARRIER
POWER
POWER
*Note: For unbalanced audio input, use the following setup
Ground Audio Input
Audio Input
Tie together
}
AR2000
FM AUDIO TRANSCEIVER
International Fiber
ifs
Systems Incorporated
POWER
Duplex multimode fiber optic cable
OPTICAL IN
OPTICAL OUT
GRD- 6 AUDIO OUT- 5 AUDIO OUT
GRD
AUDIO IN AUDIO IN
12 VAC/12 VDC- 3
GRD- 2
12 VAC/12 VDC- 1
Audio Output
- 4
- 3
- 2
- 1
}
Balanced
}
Audio Input*
Blue Green Brown
AT1000
 NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE CORRECT OPERATIONAL STATUS OF THE UNIT.
A
A
Power LED
AR1000/AR2000
B
A
A Carrier LED B
Power LED
AR2000
A
A
B
B
1 2 3 4 5 6 1 2 3
A Power Connector B
Audio Connector
C
Optical Out Optical In
D
AT1000
C
D
C
A
1 2 3 1 2 3
A Power Connector B
Audio Input Connector Optical Out
C
AR1000
B
1 2 3 4 5 6
C
A Power Connector
Audio Output Connector
B C
Optical In
PROPER MOUNTING METHOD
FOR THE AT/AR2000
1) Locate unit on solid at horizontal or vertical surface.
2) Position unit no closer than 24 inches from any power source or machinery.
3) Securely mount unit using (4) four mounting screws (not provided).
4) Attach power wires to terminal block, black wire to PIN 2 and black wire with white stripe to PIN 1.
5) Plug power brick into approved 120v AC outlet.
6) Check power LED to insure device is properly powered, LED will illuminate green.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to cor­rect the
interference at his own expense.
CLASS 1 LASER PRODUCT (For purposes of IEC 60825-1)
Complies with FDA Performance Standard for Laser Products
Title 21
Code of Federal Regulations
Subchapter J
Comprehensive Lifetime Warranty
(a) Seller warrants to the original End User that products and any services furnished hereunder will be free from defects in material and workmanship as of the date of delivery, and will conform to Seller’s published technical specications. The foregoing shall apply only to failures to meet said warranties which appear within that period of time during which the Products are installed in their original installation for the original End User and operator of such Products; provided, however, that in the event of product discontin­uance, warranty support is limited to ve (5) years from the announcement of discontinuance. Notwithstanding the preceding sentence, the duration of the warranty period for manufactured by Seller (e.g., ber optic cabling, test equipment, power supplies or batteries) shall be the warranty period oered by the original manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon and Seller shall be notied of, and may be represented at, all tests that may be made. The warranties and remedies set forth herein are conditioned upon (a) proper storage, installation, use and mainte­nance, and conformance with Seller and (b) Buyer promptly notifying Seller of any defects and, if required, promptly making the product available for correction.
(c) If any product or service fails to meet the foregoing warranties, Seller shall thereupon correct any such failure either at its option,
any applicable recommendations of
products not
(i) by repairing any defective or damaged product or parts of the products, or (ii) by making available any necessary repaired or replacement products or parts thereof. Any repaired or replacement part or product shall be warranted for the remaining period of the original Warranty Period. Seller shall pay, or credit Buyer for, the cost of freight for all return shipments of products or parts to Buyer. Where a failure cannot be corrected by Seller's reasonable eorts, the parties will negotiate an equitable adjustment in price.
(d) The preceding paragraph sets forth the exclusive remedies for claims based on defect in or failure of products or services, whether the claim is in contract, indemnity, warranty, tort (including Seller's negligence), strict liability or otherwise and however instituted. Upon the expiration of the warranty period,
liability shall terminate and BUYER shall have a reason-
all such able time, within thirty days after the warranty period, to give written notice of any defects which appeared during the warranty period. The foregoing warranties are exclusive and in lieu of all other warranties, whether written, oral, implied or statutory. NO IMPLIED OR STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY. Seller does not warrant any products or services of others which BUYER has designated.
Contacting us
For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, contact us during business hours (Monday through Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).
Sales and support contact information
North America
Toll-free: 855.286.8889 in the US, including Alaska and Hawaii; Puerto Rico; Canada.
Outside the toll-free area: 503.885.5700.
E-mail: techsupport@interlogix.com
Europe
Australia
Select Contact Us at www.utcfssecurityproducts.eu
security.tech.support@interlogix.com.au
Note: Be ready at the equipment before calling.
Online
Another great resource for assistance with your Interlogix product is our online publication library. To access the library, go to our website at the following location:
http://www.interlogix.com/transmission
1
1. Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver. One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least 4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Copyright © 2011 UTC Fire & Security. All rights reserved.
r
Trademarks and
patents
Manufacture
Certification
ACMA compliance Notice! Thi
Canada This Class A digital apparatus complies with Canadian ICES-003.
European Union
directives
Interlogix and IFS names and logos are trademarks of
UTC Fire & Security. Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the respective products.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative:
UTC Fire & Security B.V. Kelvinstraat 7, 6003 DH Weert, The Netherlands
N4131
product may cause radio interference in which case the user may be required to take adequate measures.
Cet appareil numérique de la classe A est conforme à la norme NMB-0
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
decl requirements and other relevant provisions of Directive 2004/108/EC.
03 du Canada.
ares that this device is in compliance with the essential
s is a Class A product. In a domestic environment this
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Contact information For contact information, see www.interlogix.com.
Loading...