Interlogix 80-632-3N-SP-XT5-2, 80-649-3N-XT5-2 User Manual

Simon® XTi-5 User Manual

P/N 466-5257 • REV A • 16JUN16

Trademarks and patents

The Simon® XTi-5 name and logo are trademarks of UTC Fire & Security. Other trade names used in this document may be trademarks or registered

trademarks of the manufacturers or vendors of the respective products.

Manufacturer

UTC Fire & Security Americas Corporation, Inc. 1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA.

FCC compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by UTC Fire and Security could

void the user’s authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference,and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.

In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of 20 cm is maintained from the general population.

FCC: B4Z-910C-SIMON IC: 1175C-910CSIMO This Class B digital apparatus complies with Canadian ICES-3B. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Contact information

www.utcfireandsecurity.com or www.interlogix.com

Customer support

www.interlogix.com/customer-support

IMPORTANT SAFETY INFORMATION. READ ENCLOSED WARNINGS AND SAFETY INFORMATION. THIS MANUAL CONTAINS PRODUCT SAFETY WARNINGS, WARRANTY DISCLAIMERS, LIMITATIONS OF

LIABILITY, AND OTHER TERMS AND CONDITIONS. PRODUCT WARNINGS

THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY, AN EXPERIENCED SECURITY PROFESSIONAL. INTERLOGIX CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS

PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY

INSTALL SECURITY RELATED PRODUCTS. A PROPERLY INSTALLED AND MAINTAINED ALARM/SECURITY SYSTEM MAY ONLY REDUCE THE RISK OF EVENTS

SUCH AS BREAK-INS, BURGLARY, ROBBERY OR FIRE; IT IS NOT INSURANCE OR A GUARANTEE THAT SUCH EVENTS WILL NOT OCCUR, THAT ADEQUATE WARNING OR PROTECTION WILL BE PROVIDED, OR THAT THERE WILL BE NO DEATH, PERSONAL INJURY, AND/OR PROPERTY DAMAGE AS A RESULT.

WHILE INTERLOGIX MAKES REASONABLE EFFORTS TO REDUCE THE PROBABILITY THAT A THIRD PARTY MAY HACK, COMPROMISE OR CIRCUMVENT ITS SECURITY PRODUCTS OR RELATED SOFTWARE, ANY SECURITY PRODUCT OR SOFTWARE MANUFACTURED, SOLD OR LICENSED BY INTERLOGIX, MAY STILL BE HACKED, COMPROMISED AND/OR CIRCUMVENTED.

INTERLOGIX DOES NOT ENCRYPT COMMUNICATIONS BETWEEN ITS ALARM OR SECURITY PANELS AND THEIR OUTPUTS/INPUTS INCLUDING, BUT NOT LIMITED TO, SENSORS OR DETECTORS UNLESS REQUIRED BY APPLICABLE LAW. AS A RESULT THESE COMMUNICATIONS MAY BE INTERCEPTED AND COULD BE USED TO CIRCUMVENT YOUR ALARM/SECURITY SYSTEM.

BATTERY OPERATED SENSORS, DETECTORS, KEYFOBS, PANIC DEVICES AND OTHER PANEL ACCESSORIES HAVE A LIMITED BATTERY LIFE. WHILE THESE PRODUCTS ARE DESIGNED TO PROVIDE SOME WARNING OF IMMINENT BATTERY DEPLETION THE ABILITY TO DELIVER SUCH WARNINGS IS LIMITED AND SUCH WARNINGS MAY NOT BE PROVIDED IN ALL CIRCUMSTANCES. PERIODIC TESTING OF THE SYSTEM IN ACCORANCE WITH THE INSTRUCTIONS PROVIDED IN THE USER MANUAL IS THE ONLY WAY TO ENSURE ALL SENSORS, DETECTORS, KEYFOBS, PANIC DEVICES AND OTHER PANEL ACCESSORIES ARE FUNCTIONING PROPERLY.

CERTAIN SENSORS, PANIC DEVICES AND OTHER PANEL ACCESSORIES MAY BE PROGRAMMED AS

“SUPERVISORY” INTO THE ALARM PANEL MEANING THAT THE ALARM PANEL WILL INDICATE A TROUBLE IN THE

EVENT IT DOES NOT RECEIVE A REGULAR SIGNAL FROM THE DEVICE WITHIN A CERTAIN PERIOD OF TIME (E.G. 12 HOURS). CERTAIN DEVICES CANNOT BE PROGRAMMED AS SUPERVISORY. DEVICES CAPABLE OF BEING PROGRAMMED INTO AN ALARM PANEL AS SUPERVISORY MAY NOT BE PROPERLY PROGRAMMED RESULTING IN A FAILURE TO REPORT TROUBLE WHICH COULD RESULT IN DEATH, SERIOUS INJURY OR PROPERTY DAMAGE.

WARRANTY DISCLAIMERS

INTERLOGIX HEREBY DISCLAIMS ALL WARRANTIES AND REPRESENTATIONS, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE INCLUDING (BUT NOT LIMITED TO) ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ITS SECURITY PRODUCTS AND RELATED SOFTWARE. INTERLOGIX FURTHER DISCLAIMS ANY OTHER IMPLIED WARRANTY UNDER THE UNIFORM COMPUTER INFORMATION TRANSACTIONS ACT OR SIMILAR LAW AS ENACTED BY ANY STATE.

(USA only) SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS THAT VARY FROM STATE TO STATE.

INTERLOGIX MAKES NO REPRESENTATION, WARRANTY, COVENANT OR PROMISE THAT ITS SECURITY PRODUCTS AND/OR RELATED SOFTWARE (I) WILL NOT BE HACKED, COMPROMISED AND/OR CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE ADEQUATE WARNING OR PROTECTION FROM, BREAK-INS, BURGLARY, ROBBERY, FIRE; OR (III) WILL WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS.

Contents

Introduction ..............................................................................................1

Using the Simon XTi-5 security system .................................................3

Panel controls .......................................................................................3

Main touch screen display ..................................................4

Simon XTi-5 features ............................................................................6

Cross-zoning ......................................................................6

Home security .......................................................................................7

Arming/disarming ...............................................................7

Arming errors ......................................................................7

Unvacated premises ...........................................................9

Swinger shutdown ..............................................................9

Exit/entry delay .................................................................................... 10

Silent exit .......................................................................... 10

No entry delay .................................................................. 10

Quick exit .......................................................................... 11

Exit delay extension.......................................................... 11

Bypassing sensors .............................................................................. 11

Alarms ................................................................................................ 12

Fire alarm verification ....................................................... 12

Canceling and preventing accidental alarms .................... 12

Guidelines for preventing accidental alarms ..................... 13

Chimes ................................................................................................ 13

Voice chime ...................................................................... 13

Special chime ................................................................... 14

System status ...................................................................................... 14

Using an offsite phone ........................................................................ 14

Key fobs .............................................................................................. 15

Key fob ............................................................................. 15

How your system communicates .......................................................... 17

Status beeps ....................................................................................... 17

Alarm sirens ........................................................................................ 17

Trouble beeps ..................................................................................... 18

System configuration ............................................................................. 20

Settings menu ..................................................................................... 20

Code options ....................................................................................... 20

Menu navigation .................................................................................. 20

Event History ....................................................................................... 22

Direct Bypass ...................................................................................... 22

Panel Status ........................................................................................ 22

Chime .................................................................................................. 23

Simon XTi-5 User Manual i

Special chime ..................................................................................... 23

Voice Volume ..................................................................................... 23

Beep Volume ...................................................................................... 23

Brightness .......................................................................................... 24

Default Screen ................................................................................... 24

Calibration .......................................................................................... 24

Help ................................................................................................... 25

Set time and date ............................................................................... 25

Emergency icon ................................................................................. 26

System tests ....................................................................................... 26

Programming ...................................................................................... 27

Access codes .................................................................. 27

Security ........................................................................... 28

Phone numbers ............................................................... 28

Sirens options .................................................................. 28

Version ............................................................................................... 29

Testing ................................................................................................... 30

Sensor test ......................................................................................... 30

Sensor testing notes ........................................................ 31

Comm test .......................................................................................... 31

Central station communication ........................................................... 32

System download ............................................................................... 32

Reference information .......................................................................... 33

Alarm system limitations..................................................................... 33

Emergency planning .......................................................................... 34

Your floor plan ................................................................. 35

Cleaning the touch screen.................................................................. 35

Disposal ............................................................................................. 36

Sensor and module locations ............................................................. 36

Access codes ..................................................................................... 37

Delays ................................................................ ................................ 37

Simon XTi-5 system quick reference .................................................. 38

ii Simon XTi-5 User Manual

Component

Type

Description

Control panel

Operates and programs your security system. It communicates to you through displayed and spoken messages. The panel can communicate to a central monitoring station and send voice messages to your offsite phone.

Touchpads

Simon XT talking touch screen and Simon XT Talking Touchpad a

Controls the security system primarily from within the house. Key fob a

This keychain touchpad controls the security system from within or near the outside of your home.

Sensors

Indoor motion

Detects motion in protected indoor area. When motion is detected, the panel may respond by sounding chimes or an alarm.

Outdoor motion

Detects motion in a protected outdoor area. When motion is detected, the system may respond by sounding chimes or turning on outside lights. These sensors are not used for intrusion detection.

Glassbreak sensor

Glassbreak sensors respond to shock waves of breaking glass.

Door/window

Detects the opening of a door or window.

Smoke

Detects smoke or a significant rise in temperature. They have a built-in siren that sounds when smoke or a significant rise in temperature is detected.

Carbon monoxide

Detects carbon monoxide. They have a built-in siren that sounds when carbon monoxide is detected.

Introduction

The Simon XTi-5 uses wireless technology to warn your family about intrusion, carbon monoxide and fire. The system communicates with a central monitoring station and sends voice messages to an offsite phone.

The security system uses sensors that communicate alarms to the control panel using radio waves. The system is supervised, meaning that the panel checks the status of each sensor to detect problems. If the panel detects trouble, it will notify you with displayed and spoken messages, beeps, and indicator lights. A Simon XTi-5 installation may include any of the devices listed in Table 1 below.

Table 1: Simon XTi-5 system components

a. Not verified for use by UL.

You can send commands or instruct your security system through a series of key presses on the panel, touchpads, or a remote telephone.

Simon XTi-5 User Manual 1

Device

Description

Control panel

You can enter commands for your security system using the graphical user interface on the panel. Depending on how your system is programmed, you may need to enter an access code for certain commands. An access code is a numeric code that allows authorization to operate your security system.

Simon XT talking touch screen

The two-way talking touch screen is a wireless device that provides a graphical user interface that allows you to: arm the system (doors, windows, and motion sensors), disarm the system, activate a panic alarm to call the central monitoring station in an emergency, check system status, and turn system controlled lights on or off, all while providing voice feedback. The touch screen also provides trouble beeps, entry/exit beeps and alarm sounds (Panic, Police, or Fire).

Key fob

Key fobs are handy for simple arming and disarming control functions. They are portable and can be carried offsite in a purse or pocket.

Telephone

Touchtone telephones can be used to communicate with your system while you are offsite. Ask your installer if you have this feature.

Table 2: System communication devices

Note: The default master code is 1-2-3-4 when the security system is shipped

from the factory. You should change your code after your system is installed.

2 Simon XTi-5 User Manual

Using the Simon XTi-5 security system

You can operate the self-contained security system through several different methods:

• Use the main screen icons to arm/disarm the system when you enter or exit your home, check system status, and to determine which sensors are active.

• Use the emergency screen to communicate with the central monitoring station to report emergency panic, police, or fire alarms.

• From the home screen, press the Status & Settings icon to program certain user features. (See System configuration on page 20).

Note: Upon initial installation, the battery may not be fully charged for as long as 36 hours. A low battery icon will be present and trouble beeps will sound until the battery is sufficiently charged. After the initial charge, should the panel lose AC Power and experience a low battery condition, the icon will appear and trouble beeps will sound unless silenced. You can silence trouble beeps by:

• Arming or disarming the system.

• Pressing the STATUS & SETTINGS icon and pressing LISTEN next to Panel Status.

This will disable the sounder for 4 hours but the trouble indication will remain until the battery is recharged.

Contact your installer to replace your backup battery.

This system is intended to be checked by a qualified technician at least once every 3 years.

Panel controls

The self-contained panel provides the user interface for system operation and programming system functions.

Simon XTi-5 User Manual 3

Control

Description

Piezo siren

Provides alarm beeps and status beeps.

Touch screen

Provides a graphical user interface for programming and system operation.

Microphone

Used to communicate with the central monitoring station after an alarm.

Speaker

Provides voice output and sounds key beeps.

Access the emergency screen to select the appropriate emergency icon (Panic, Police, or Fire).

Time

The current system time

These icons only appear in red on the main screen if the backup battery is not fully charged or the AC power is not working correctly. It is recommended that the backup battery be replaced every 3-5 years. Contact your installer to replace the backup battery.

Figure 1: Simon XTi-5 controls

Note: The touch screen in Figure 1 above is an example. Your touch screen and

system may be configured differently. Table 3 below provides a description of the panel’s graphical user interface and

audio.

Table 3: Panel features

Main touch screen display

While the panel is idle, the screen displays:

Table 4: Main screen icons

4 Simon XTi-5 User Manual

Depicts monitored door status. A green check indicates all monitored doors are closed. A red exclamation point indicates one or more doors are open. N/A indicates your system is not configured to support door sensors.

Depicts monitored window status. A green check indicates all monitored windows are closed. A red exclamation point indicates one or more windows are open. N/A indicates your system is not configured to support window sensors.

Depicts motion detected by the motion sensors in your home. A green check indicates no recent motion detected. A red exclamation point indicates motion was detected within the last 10 minutes. A typical use for this feature would be to have a Simon two-way talking touch screen in the garage to see if movement is detected in the home before you enter the home. N/A indicates your system is not configured to support motion sensors.

Depicts other changes to protected property in your system. For example activation of a water sensor, freeze sensor, or the movement of protected items. A green check indicates no change since the last time you visited (for movement of a protected item) and all sensors are closed (water or freeze sensors). A red exclamation point indicates either a sensor is tripped or there is unacknowledged activity. N/A indicates your system is not configured to support property sensors.

Depending on the current arming state of your machine, one of these icons will be displayed. Press the ARM icon to access the Arming Screen. Press a DISARM icon, and provide a valid access code, to disarm your system.

Note: When disarming the system, only intrusion/burglary sensors are disarmed. Environmental sensors, such as smoke and carbon monoxide detectors, stay active at all times.

Note: Depending on your configuration, the Motions Only icon may not appear.

Press to access the settings screen.

This yellow triangle indicates faults within the system.

Simon XTi-5 User Manual 5

Simon XTi-5 features

The Simon XTi-5 features provide you with the ability to perform the following functions:

• Arm perimeter (doors and windows) and interior (motion) sensors to indicate intruders.

• Use the emergency screen to send quick response alerts to the central monitoring station.

• Access the system from a key fob (similar to the one used for your car).

• Access the system from a remote telephone.

• Disable sensors so you can leave a window open while the system is armed.

• Get an audio alert when a protected door is opened while the system is

disarmed.

• Get an audio alert if movement of a protected asset is detected (group 43).

Cross-zoning

Cross zoning (two-trip) refers to two different motion sensors that must be tripped within two minutes of each other to report an alarm to the central station. Figure 2 below shows the path of a person walking from the kitchen to the living room. When the person is detected walking through the kitchen, the motion sensor in the kitchen is tripped, sounding a local alarm. If motion is detected by the living room motion sensor within two minutes, an alarm report will be sent to the central station.

Note: Contact your installer for more information.

Figure 2: Cross-zone diagram

6 Simon XTi-5 User Manual

Level

Function

Description

Disarm

In this level, only 24-hour sensors are active. Environmental sensors (such as smoke or carbon monoxide detectors) stay active at all times.

Arm door and window sensors (stay)

This level arms the door and window sensors, while leaving the interior motion sensors disarmed.

Arm motion sensors (away)

This level arms the interior motion sensors, while leaving the exterior door and window sensors disarmed. Note: Depending on your configuration, this option may not appear.

Arm doors/windows and motion sensors

This level arms all sensors.

Home security

The Simon XTi-5 allows you to control which sensors are active at any given time. Table 5 below describes the arming levels that you can set from the control panel.

Table 5: Arming levels

Arming/disarming

Arming a sensor makes it active and allows the panel to generate an alarm when a door or window is opened or when an unauthorized person enters a specific area. Disarming makes the sensor inactive in the system. The current arming level is shown on the screen (see Table 4 on page 4) and changes in arming level are announced on the speaker.

Arming errors

If you select an arming option on the Arm screen, and there is an arming problem, an arming error message screen will appear, indicating what the problem is and how to correct it. For example, you might see a message that indicates that you need to close the front door.

Correct the problem as indicated or press Bypass. You will see the arming countdown message at the bottom of the screen. You can press Cancel and enter your code to stop the arming process.

Simon XTi-5 User Manual 7

Figure 3: Pre arm screen

To disarm (level 1):

1. Press PRESS TO DISARM.

2. Enter your code when the keypad screen appears.

The panel displays and speaks Disarmed and the panel beeps once.

To arm doors and windows (level 2):

1. Ensure that all doors and windows are closed.

2. Press .

3. Press DOORS & WINDOWS ONLY (STAY) (see Figure 3 above).

4. If a code is required, enter your code when the keypad screen appears. The panel speaks Doors and Windows On and starts an exit delay, and

sounds exit beeps in groups of two until the exit delay expires. To cancel arming press CANCEL ARMING on the countdown screen.

8 Simon XTi-5 User Manual

+ 30 hidden pages