Interlogix 3050 User Manual
STEP 1 - MOUNTING
0 46188 02709 5
1. Determine the best location for the 3040/3050 based on the
work habits of the end user and their physical reach. The 3040
should be placed such that the user would not call attention
while activating the switch. Typical mounting positions are on
the sides of desks in the kneehole area, or under counters away
from view. The 3050 with its lit LED (green) is visible in low light
environments or at night. The unit should be mounted within the
line of sight, so that the LED is not obstructed. The device can
be located in a hall, entryway or near a bedside. The lever must
be oriented vertically or horizontally as shown in the illustrations
below.
Desk Mount
Under Counter
3040/3050 SERIES
PANIC SWITCH
Installation Instructions
IMPORTANT: You must allow at least 3" (7.62cm) of clearance above the mounting surface to accommodate the
actuating lever once it is fully open.
Maximum 3" Clearance
When Lever Fully Open
Lever
Actuates Between
20° and 45°
Kneehole of Desk, Horizontal
Freezer Mount
Kneehole of Desk, Vertical
2. Temporarily position the unit where it will be mounted, and
mark the screw holes and the hole for the leads.
Screw
Holes
3. Drill pilot holes or start the screws. Connect the wire leads to
the terminal block (see wiring diagram).
4. After the leads are wired, install cover plate by snapping it in
place. Then, insert the screws through the switch housing and
firmly secure unit into place.
Cover
Plate
Wire
Leads
STEP 2 - WIRING
To test and rearm the SPDT switch, do the following:
The wiring diagrams show two separate circuits: the SPDT
circuit and the latching LED circuit. The latching LED must be
powered and controlled by, respectively, a +12 VDC source in
the alarm panel (24 hour switchable power loop or equivalent),
and a normally closed push-button or spring-loaded momentaryaction toggle switch inside or mounted outside the panel. Wire
the reset circuit in series to the LED circuit as shown.
Latching
LED
Circuit
To N.C. and
N.O. Connections
+ –
COM
N.C. N.O.
–
(12 VDC)
+
LED Reset
(N.C. Push Button)
When the actuating lever is pulled between 20° to 45°, the alarm
circuit switch (SPDT) will actuate. Then the LED will latch and
light or change to red (3050), indicating that the SPDT switch
has been activated. Closing the handle rearms the SPDT switch.
However, the LED remains lit.
IMPORTANT: The lever must be closed first to reset the
SPDT circuit before the LED is reset.
1. Pull the handle down until the LED lights or changes to red
(3050), indicating that the SPDT alarm circuit has been activated.
LED Latches
and Lights
2. Close the handle. The SPDT switch is now fully re-armed.
The LED remains lit.
3. Activate the normally closed push-button or toggle switch
located at the master control panel to interrupt power to the
latching LED. The LED will go out or change to green (3050).
SPECIFICATIONS
Nominal Voltage..................................................12 VDC @ 6mA
Operational Voltage ........................................... 7 VDC - 15 VDC
Current Draw................................................................. Max 8mA
Temperature ....................................... 0° to 110°F (-18° to 48°C)
Dimensions . 1.77" (4.50cm) W x 2.90" (7.37cm) L x .76" (1.93cm)
D
Weight ................................................................................1.5 oz.
Housing Material ........................................................ ABS plastic
Lead Colors for 3040CT, 3050CT Form C
Green Common
Brown Closed Loop (N.O.)
White Open Loop (N.C.)
Red Positive
Black Negative
ORDERING INFORMATION
Model Latching Electrical
Number LED Circuit Loop Type Configuration Color Listed
3040 Red Yes Open or Closed SPDT White UL
3040CT Red Yes Open or Closed SPDT White UL
3050 Bi-color Yes Open or Closed SPDT White UL
* European Union Specification: 48 V AC/DC Max., 0.5 Amp
C-3732-0299
14327 Rev B
Loading...