Interlogix 2-Button Crystal Keychain Touchpad User Manual
2-Button Keychain
Touchpad
Document Number: 46-897 Rev. A
January 1995
60-607
INSTALLATION
INSTRUCTIONS
About This Document
This document describes how to install and operate
the 2-Button Keychain Touchpad.
Product Summary
The Keychain Touchpad is an alkaline battery-powered, wireless touchpad designed to fit on a keychain,
in a pocket or purse. It provides users a convenient
option for the following system operations:
ν Arming the system
ν Arming the system with no delay
ν Disarming the system
ν Police Panic alarm
Installation Guidelines
2-Button Keychain Touchpad
ν Keychain Touchpads are learned into the Panel as
sensors or wireless touchpads.
ν Each learned Keychain Touchpad uses one of the
available sensor numbers or one of the four wireless touchpad numbers.
For example, if a CareTaker Plus system (32
zones) has six Keychain Touchpads learned as
sensors, 26 available sensor numbers remain.
ν Keychain Touchpads learned as sensors are pro-
grammed into unsupervised groups (since they
don’t send supervisory signals) that determine
how the Panel responds when both Keychain
Touchpad buttons are pressed together.
ν When learned as sensors, Keychain Touchpads
can be bypassed or deleted. This helps prevent
lost or stolen Keychain Touchpads from operating
the system.
ν Keychain Touchpads learned as sensors use the
sensor number as the user number for central station reports that include a user number.
ν All Keychain Touchpads learned as touchpads in
CareTaker Plus and Security Pro 4000 systems
report to the central station as user number 41.
For Commander 2000 and Security Pro 2000 systems, Keychain Touchpads report as user number
20. These touchpads cannot be bypassed, but they
can be deleted.
Tools Needed
ν Phillips screwdriver (for removing and replacing
the Panel cover or battery door)
Learning Keychain Touchpad s into Panel Memory
Use the following guidelines when adding Keychain
Touchpads to the system:
ν CareTaker
must have software version 3.0 (or later) installed
for Keychain Touchpad operation.
ν Commander
must have software version 4.0 (or later) installed
for Keychain Touchpad operation.
®
Plus and Security Pro 4000 Panels
®
2000 and Security Pro 2000 Panels
This section describes how to learn Keychain Touchpads into Panel memory for CareTaker Plus, Security
Pro 4000, Commander 2000, and Security Pro 2000
Panels.
CareTaker
To learn Keychain Touchpads as sensors:
1) Disarm the system to level 1.
Plus
and Security Pro 4000
Page 1
2-Button Keychain Touchpad
2) Place the Panel in the program mode by r emoving
the Panel cover.
3) Using an alphanumeric touchpad, enter the learn
sensors mode, then press COMMAND.
4) Select the appropriate unsupervised group number (01, 03, 06, 07, 32) and press COMMAND.
5) Select the desired sensor number (1 through 32 for
CareTaker Plus, 1 through 40 for Security Pro
4000) you want assigned to the Keychain Touchpad and press COMMAND.
6) Trip the Keychain Touchpad by pressing and
holding the arm and disarm buttons together,
until the LED flashes. The Panel announces “Sensor nn okay.”
7) Repeat steps 5 and 6 until all Keychain Touchpads
are learned.
8) Replace the Panel cover.
To learn Keychai n Touchpads as W ir eless Touchpads:
Note: If the system includes other wireless touchpads,
they must be programmed at this time, even if
they already exist in Panel memory. If existing
touchpads are not reprogrammed, they are deleted
from memory when pressing COMMAND after
entering the
learn touchp ads mode.
6) Trip the Keychain Touchpad by pressing and
holding the arm and disarm buttons together,
until the LED flashes. The Panel announces “Sensor nn okay.”
7) Repeat steps 4, 5, and 6 until all Keychain Touchpads are learned.
8) Replace the battery door.
To learn Keychain Touchpads as Wireless Touchpads:
1) Disarm the system to level 1.
2) Remove the battery door.
3) Enter either the installer or dealer programming
code.
4) Press STATUS + STATUS + n (n = touchpad ID
number 1, 2, 3, or 4).
5) Trip the Keychain Touchpad by pressing and
holding the arm and disarm buttons together,
until you see the LED flash. The Panel announces
“N okay.”
6) Repeat step 5 until all Keychain Touchpads are
learned.
7) Replace the battery door.
Testing Keychain Touchpad Operation
1) Disarm the system to level 1.
2) Place the Panel in the program mode by r emoving
the Panel cover.
3) Using an alphanumeric touchpad, enter the learn
touchpads mode and press COMMAND. The
alphanumeric display reads PRESS TP 01 BYP.
4) Press the Keychain Touchpad arm and disarm
buttons together, until the LED flashes. The Panel
announces “N okay.”
5) Repeat step 4 until all Keychain Touchpads and
wireless touchpads are learned.
6) Replace the Panel cover.
Commander 2000 and Security Pro 2000
To learn Keychain Touchpads as sensors:
1) Disarm the system to level 1.
2) Remove the battery door.
3) Enter either the installer or dealer programming
code.
4) Select the appropriate unsupervised group number by pressing STATUS + nn (nn = 01, 03, 06, 07).
The Panel announces “Sensor level nn.”
5) Enter the desired sensor number (01 through 17).
Test Keychain Touchpad operation by pressing the
buttons as described below:
1) Disarm Button - The Panel disarms to level 1.
2) Arm Button - With optional feature number F25
off:
ν the Panel attempts arming from level 1 to level 2
ν the Panel attempts arming from level 2 to level 3
ν if protesting, the Panel responds as if BYPASS was
pressed
With optional feature number F25 on:
ν the Panel arms directly to level 3, with no delay
ν if protesting, the Panel responds as if BYPASS was
pressed
3) Arm and Disarm Buttons Together - The Panel
responds with an alarm condition as follows:
ν Keychain Touchpads learned as sensors generate
an alarm based on the sensor group in which they
are learned
ν Keychain Touchpads learned as wireless touch-
pads generate a police panic alarm (upper sensor
number 81)
Page 2
Loading...