Intel XP-P5IM800GV User Manual

XP-P5IM800GV
Intel® Pentium® 4 LGA775 Processor Motherboard
User's Manual
M-050401
Copyright Declaration
©2005 Gigatrend Technology Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without express permission from Gigatrend Technology. Companies and product names mentioned in this document are trademarks or registered trademarks of their respective owners.
Legal Disclaimer
The information and content of this document is provided "as is", without warranty of any kind, express or implied, including but not limited to the warranties of merchantability, fitness for a particular purpose and non-infringement. Gigatrend Technology assumes no responsibility for errors or omissions in this document or other documents which are referenced by or linked to this document. The content of this document are subject to change without prior notice. Gigatrend Technology may make improvements and/or changes in the product described in this publication at any time and without prior notice. In no event shall Gigatrend Technology be liable for any special, incidental, indirect or consequential damages of any kind arising out of or in connection with the use or performance of this document. If you are uncertain about any installation procedures, please consult a qualified computer technician.
Terms of Use
To avoid unnecessary errors of operation, please consult the user manual prior to hardware installation. For more up-to-date information, please link to our company website at http:// www.axper.com.tw Prior to beginning installation procedures, please make sure that your computer turned off and is connected to a grounded power outlet. If your system is not turned off during installation, this could result in harm or damage to the motherboard, the components as well as to the user.
Motherboard
May 27, 2005
Motherboard XP-P5IM800GV
May 27, 2005
Contents
Motherboard Layout ........................................................................4
1. Product Introduction..................................................................5
1.1. Feature Summary .............................................................................. 5
1.2. I/O Back Panel and Connectors&Jumper Setting............................. 6
1.2.1. I/O Back Panel ...................................................................................... 6
1.2.2. Connectors&Jumper Setting ................................................................ 6
2. Hardware Installation ................................................................9
2.1. Installation of a LGA775 Pentium 4 CPU and Fan Sink ................. 10
2.1.1. Installation of a LGA775 CPU ............................................................ 10
2.1.2. Installation of Fan Sink .......................................................................10
2.2. Installation of Memory ......................................................................11
2.3. Installation of the Graphics Card..................................................... 12
2.4. What is Axper's A.G.U.? .................................................................. 12
2.4.1. Graphics Card Support List ................................................................ 12
3. BIOS Setup............................................................................15
3.1. Setup Screen Features (BIOS version: F3) .................................... 15
3.2. Standard CMOS Features............................................................... 16
3.3. Advanced BIOS Features ............................................................... 18
3.4. Integrated Peripherals ..................................................................... 19
3.5. Power Management Setup.............................................................. 21
3.6. PnP/PCI Configuration .................................................................... 22
3.7. PC Health Status............................................................................. 23
3.8. Frequency/Voltage Control .............................................................. 24
3.9. Load Fail-Safe Defaults................................................................... 25
3.10. Load Optimized Defaults................................................................. 25
3.11. Set User Password.......................................................................... 25
3.12. Save & Exit Setup............................................................................ 25
3.13. Exit Without Saving ......................................................................... 25
4. Driver Installation....................................................................26
English
Motherboard Layout
KB_MS
COMA
VGA
LPT
ATX_12V
LGA775
CPU_FAN
ATX
R_USB
AUDIO
F_AUDIO
RTL8100C
USB
CODEC
CD_IN
SmSC LPC47M997-NR
LAN
AGU
FDD
Intel 865GV
PCI2
PCI3
SYS_FAN
PCI1
XP-P5IM800GV
ICH5
PWR_LED
BIOS
F_USB1
DDR1
IDE2
DDR2
SATA1
SATA0
BAT
F_PANEL
IDE1
CLR_CMOS
4
1. Product Introduction
The user manual provides steps related to quick installation. If you wish to view complete product information, please select the " ",Open User Manual button located on the driver
CD or link to our website at http://www.axper.com to received the most up-to-date information.
1.1. Feature Summary
CPU LGA775 for Intel®Pentium®4 Processor
Intel®Pentium®4 533/800MHz FSB L2 cache depends on CPU
Chipset North Bridge: Intel
South Bridge: Intel
Memory 2 184-pin DDR DIMM sockets, supports up to 2GB DRAM (Max)
Supports dual channel DDR400/DDR333 DIMM Supports only 2.5V DDR SDRAM
Slots 1 AGU slot device support
3 PCI slots support 33MHz & PCI 2.2 compliant
On-Board IDE 2 IDE controller provide IDE HDD/CD-ROM(IDE1, IDE2) with PIO,
Bus Master (Ultra DMA33/ATA66/ATA100) operation modes Can connect up to 4 IDE devices
On-Board Floppy 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and
2.88M bytes On-Board SATA 2 Serial ATA ports On-Board Peripherals 1 Parallel port supports Normal/EPP/ECP mode
1 Serial port (COMA), 1 VGA port 6 USB 2.0/1.1 ports (4 x Rear, 2 x Front by cable) 1 Front Audio connector 1 PS/2 Keyboard 1 PS/2 Mouse
On-Board LAN Built-in RTL8100C chipset
1 RJ45 port On-Board VGA Built-in Intel On-Board Sound ALC655 CODEC
Supports 2/4/6 channel
Line Out / Line In / Mic In
CD In BIOS Licensed AWARD BIOS
Supports BIOSNow! I/O Control SmSc LPC47M997-NR Hardware Monitor CPU/System Fan Revolution detect
CPU/System temperature detect
System Voltage detect Form Factor Micro ATX size form factor, 24.4cm x 21cm
®
865GV
®
ICH5
®
865GV chipset
English
5
English
1.2. I/O Back Panel and Connectors&Jumper Setting
1.2.1. I/O Back Panel
PS/2 Keyboard Connects PS/2 standard keyboard and PS/2 standard PS/2 Mouse connector mouse Parallel port (LPT) Connects to printer COMA (Serial port) Connects to serial-based mouse or data processing devices VGA port Connects to 15pin D-Sub device such as a monitor USB Prior to use, please make sure that your system as well (Universal Serial Bus Port) as the connected attachments support the USB interface.
LAN (RJ45 LAN Port) Internet connection with speed of up to10/100Mbps Line In Connects to optical devices, CD players and other audio
LineOut Connects to speakers or headphones Mic In Connects to microphone
PS/2 Mouse
PS/2 Keyboard
Parallel Port
LAN
USB
VGACOMA
USB
If driver installation is required, please consult the USB section of the user manual.
input devices
Line In Line Out
MIC In
1.2.2. Connectors&Jumper Setting
FDD (Floppy Disk Drive Connector)
The FDD connector is able to connect a single floppy disk drive via a FDD cable. Usually one edge of the FDD cable is marked in red, please attach this marked edge to position 1 on the connector.
IDE1 / IDE2 (IDE1 and IDE2 Connector)
The IDE connector is able to connect two IDE devices via an IDE cable and requires checking of the IDE jumper setting. It is recommended that the hard drive be connected to the first IDE connector while the optical drive be connected to the second IDE connector.
6
2 34
1
2
1
33
40
39
English
CPU_FAN (CPU Fan Power Connector); SYS_FAN (System Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(only for CPU_FAN) power connector and possesses a ful-proof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indi­cates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Please remember to connect the power to the cooler to prevent system overheating and failure. Caution! Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.
PIN SIGNAL
1
CPU_FAN
SYS_FAN
ATX_12V (+12V Power Connector)
The ATX_12V power connector provides power to the CPU. If this connector is not Attached, the system will not start.
24
3
1
ATX (ATX Power Connector)
The ATX power connector provides power to the motherboard. Prior to connection, please make sure that the power supply is disconnected.
20
10
11
1
F_PANEL (Front Panel Control Connector)
The F_Panel Control Connector connects to certain connectors on the front panel of the system casing such as IDE Hard Disk Active LED, speaker, reset, and power on/off connectors. You can use the schematic diagram below as the basis for connection.
MSG+
PW+
SPK+
PW-
MSG­2 1
HD-
RES+
HD+
RES-
SPK-
20 19
NC
1 GND
1
2 +12V 3 Sense 4 Speed Control (Only for CPU_FAN)
PIN SIGNAL
1 GND 2 GND 3 +12V 4 +12V
PIN SIGNAL
1 3.3V 2 3.3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5VSB (stand by +5V)
10 +12V
PIN SIGNAL HD IDE Hard Disk Active LED SPK Speaker Connector RES Reset Switch PW Soft Power Connector MSG Message LED/Power/Sleep LED NC NC
PIN SIGNAL
11 3.3V 12 -12V 13 GND 14 PS_ON (soft on/off) 15 GND 16 GND 17 GND 18 -5V 19 VCC 20 VCC
7
PWR_LED
English
Connects to the system power LED indicator whereby the power is indicated as ON or OFF. However, the indicator will flash when the system is suspended.
SATA0/SATA1 (Serial ATA Connector, controlled by ICH5)
The SATA0/1 connector is able to connect a single Serial ATA device via a SATA cable. For the connected SATA hard disk to work correctly, please check the related BIOS setting and install proper driver for the SATA controller.
F_AUDIO (Front Audio Connector)
Connects to the audio connector located on the front panel of the system casing (dependent on case design). When use of the front panel audio connector is required, please remove the 5-6 pin, 9-10pin jumper. Please note that use of only the front panel audio connector or the rear panel audio connector is permitted.
CD_IN (Optical Drive Audio Connector)
Connects CD-ROM or DVD-ROM audio connector.
F_USB1 (Front USB Connector)
Connects to the USB connector located on the front panel of the system casing (dependent on case design). Note: Please make sure that each USB connection matches its designated position. If connections are made incorrectly, the result can lead to inability to use the function or even damage.
8
1
7
1092
2
1
PIN SIGNAL
1 MPD+ 2 MPD­3 MPD-
PIN SIGNAL
1 GND
1
1
1
10
9
2 TXP 3 TXN 4 GND
PIN SIGNAL
1 MIC 2 GND 3 MIC_BIAS 4 POWER 5 Front Audio (R)
PIN SIGNAL
1 CD_L 2 GND 3 GND 4 CD_R
PIN SIGNAL
1 POWER 2 POWER 3 USB Dx­4 USB Dy­5 USB Dx+
PIN SIGNAL
5 RXN 6 RXP 7 GND
PIN SIGNAL
6 Rear Audio (R) 7 Reserved 8 NO PIN 9 Front Audio (L)
10 Rear Audio (L)
PIN SIGNAL
6 USB Dy+ 7 GND 8 GND 9 NO PIN
10 NC
CLR_CMOS (Clear CMOS)
You can clear the motherboard CMOS with the jumper to return your system to its initial status. To prevent improper usage, the jumper does not include the jumper plug. If you wish to use the Clear CMOS function, please short circuit the 1-2 Pin.
English
Open : Normal
1
Short : Clear CMOS
1
BAT(Battery)
The improper removal of the battery can result in harm. When replacing a battery, please make sure you use one that is of similar brand and model number. For information related to battery specifications and precautions, please refer to the manufacturer instructions. If you wish to delete the data stored in the CMOS, please follow the steps below:
1. Please turn off your computer and unplug the power.
2. Remove the battery from the motherboard.
3. Wait 10 minutes and then replace the battery onto the motherboard.
4. Plug in the power supply and turn on your system.
2. Hardware Installation
1. Please make sure that the CPU used is supported by your motherboard.
2. Please be aware of the placement position of the CPU. If the CPU does not insert properly, do not apply force but check the placement position.
3. Please make sure that an even layer of heat sink paste is added between the CPU and the fan sink.
4. Please do not turn on the power prior to installing the fan sink. Doing so can result in overheating and lead to permanent damage to the CPU.
5. Please follow the CPU specifications when setting the frequency. It is not recommended that system speed settings exceed that of hardware specifications. If you wish to set your system speed to exceed the recom mended specifications, please check your hardware specifications eg: CPU, graphics card, memory, hard drive
The following must be supported to allow the use of Hyper-Threading Technology:
- an Intel Pentium 4 CPU with HT
- a motherboard supporting HT
- HT selection feature within BIOS
- an operating system supporting HT
9
English
2.1. Installation of a LGA775 Pentium 4 CPU and Fan Sink
2.1.1. Installation of a LGA775 CPU
1. Push the socket lever arm down and away from the CPU socket and raise it up completely.
2. Open the load plate and gently remove the plastic cover.
3. Hold the CPU with your thumb and index fingers (do not touch the bottom of the CPU when holding it). Align notchs on the two sides of the CPU with the small sockets of the CPU socket and place the CPU straight down.
4. Make sure the CPU is properly installed and then close the load plate. Lower the socket lever and engage it to lock the CPU in place.
2.1.2. Installation of Fan Sink
1. Apply a thin coating of thermal paste to complete cover the surface of the CPU.
10
2. Align the four fasteners of the fan sink with the four holes around the CPU socket. Push down each fastener and you should hear a "click" when the fastener is attached. Make sure the four fasteners are attached securely.
Prior to installation of the fan sink, check the direction of each fastener by the arrow engraved on fastener top. Before attaching the fasteners, turn each fastener clockwise. To uninstall the fan sink, release each fastener by rotating the fastener along the direction of the arrows and pull them up.
3. Connect the 4-wire power cable of the fan sink to the CPU_FAN header on the motherboard to complete the installation.
2.2. Installation of Memory
1. Before installing or removing memory, please make sure that the computer power is turned off to prevent hardware damage.
2. Please make sure that the memory used is supported by the motherboard.
3. Memory modules have a foolproof insertion design. The memory can be in stalled only when facing the correct position. If you cannot insert the module, please switch directions.
4. It is recommended that memory of similar capacity, specifications and brand be used.
English
The motherboard supports DIMM memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction.
1. Unfasten the clips on each end of the memory slots. Correctly align the memory module in the slot and push downwards..
2. Once the memory module is correctly inserted, the clips will automatically refasten. If the memory module is positioned in the wrong direction, it will not insert. If this occurs, please switch directions.
11
English
1. Before installing the graphics card, please carefully read the accompanying user manual.
2. When installing or removing the graphics card, first pull out the white AGU knob before
2.4. What is Axper's A.G.U.?
Axper's Advanced Graphics Upgrade (A.G.U.) is a unique feature on 865GV motherboards that includes an added AGP graphics interface. Axper's A.G.U. allows the addition of a graphics card for high-performance graphics for multimedia and gaming applications. Axper's A.G.U. is both AGP 4X and 8X compatible and supports the new Microsoft DirectX 9.0 standard.
The Advantages of Axper's A.G.U.
1) Performance
Axper's 865GV motherboards offers better graphics output than other 865GV platforms due to the extra addition of a dedicated AGP graphics interface
2) Flexibility
With the Axper A.G.U., users have the flexibility in choice of a wide range of AGP4X and AGP8X-based graphics cards (please refer to support list on manual or website) for their 865GV chipset platforms.
3) Value
Axper's 865GV motherboards provide superior value by offering performance nearing to that of 865G chipset platforms but at a noticeably lower cost for great performance at unbelievable savings!
2.3. Installation of the Graphics Card
As well, make sure the computer power is turned off.
insertion or removal. Releasing the AGU knob will hold the graphics card firmly in place.
2.4.1. Graphics Card Support List
(The items below are all supported under the Windows XP operating system. When using an add-on graphics card, please first delete the onboard graphics driver before installing the driver for the add-on graphics card.)
Figure 1-1. 4X AGP Card
Graphics Chip Maker Model Name Nvidia Gigabyte GV-GF2010D
Gigabyte GV-GF3000D Gigabyte GV-GF1280T-32P Gigabyte GV-GF3500TF-GH
12
To be continued...
Figure 1-2. 4X AGP Card
Graphics Chip Maker Model Name Nvidia ELSA Gladiac 517
ELSA Gladiac 517vivo ELSA Gladiac 525 A128 Leadtek WinFast A170 TH Leadtek WinFast A250 TO Leadtek WinFast A250 Ultra
ATi Gigabyte GV-AR64S-H
Gigabyte GV-AP128DG-H Gigabyte GV-AF128D-GH Gigabyte GV-AV32S Gigabyte GV-AV64S
Figure 2. 8X AGP Card
Graphics Chip Maker Model Name Nvidia Gigabyte GV-N4464D
Gigabyte GV-N4064T Gigabyte GV-N52128DE Gigabyte GV-N55128DP Gigabyte GV-N57L128D Gigabyte GV-N57128DE Gigabyte GV-N57128DP Gigabyte GV-N59X128D Gigabyte GV-N68128DH Gigabyte GV-N68T256D Gigabyte GV-N68U256D ASUS V9480-TVD MSI MX440-VTD8X MS-8888 MSI Ti4600-TD-8X Leadtek WinFast A280LE TD Leadtek WinFast A310 TD Albatron Gigi
ATi Gigabyte GV-R9700
Gigabyte GV-R9500 Gigabyte GV-R98P128D Gigabyte GV-R7064T Gigabyte GV-R92S64T Gigabyte GV-R92128TE Gigabyte GV-R92128DH Gigabyte GV-R925128D Gigabyte GV-R98X256D
SiS Triplex Xabre Pro
Power Color Xabre 600 Pro
English
For the most up-to-date information related to graphics card support, please link to our website at http://www.axper.com
13
English
14
3. BIOS Setup
BIOS (Basic Input and Output System) stores all the information of the motherboard settings that is needed for system initiation within the CMOS. The CMOS SETUP utility allows the user to make changes in BIOS configurations that are required or to activate certain features. The CMOS SETUP saves each item configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the required power to the CMOS SRAM. When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test) will bring up the CMOS SETUP screen. If you wish to enter the BIOS setup, please press "Ctrl + F1" at the BIOS setup screen. When using BIOS setup for the first time, it is recommended that you save the present BIOS onto a disk in case you need to reset the BIOS back to its original settings. If you wish to update to a new BIOS, the "BIOSNow!" can be used. The user can select "BIOSNow!" as a way to quickly and easily update or back up BIOS without entering the operating system.
3.1. Setup Screen Features (BIOS version: F3)
ø When you enter the CMOS SETUP screen, you will see the following screen and setting
selections as shown below.
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
} Standard CMOS Features } Advanced BIOS Features } Integrated Peripherals } Power Management Setup } PnP/PCI Configurations } PC Health Status } Frequency /Voltage Control
ESC: Quit higf: Select Item F8: BIOSNow! F10: Save & Ex it Setup
Time, Date, Hard Disk Type...
Load Fail-Safe Defaults Load Optimized Defaults Set Sup ervisor Password Set User Password Save & Ex it Setup Exit Without Saving
English
Instructions < , , , ,Enter> Movement in all four directions to highlight a desired option,
pressing <Enter> will select the option and take you to its appropriate screen
<Page Up,Page Down> Used to toggle up and down the available options for a
particular item, whereby <Page Up> can also be used to increase value option and <Page Down> to decrease
value option <Esc> Return to main setup screen or exit setup <F1> Gives the list of options available for each item <F2> Gives the list of options available for the current item <F5> Returns settings to previous values (not applicable to main setup
screen)
15
<F6> Gives the list of options available for each item
English
<F7> Return to Optimized default values (not applicable to main
<F8> Enters Expert-Flash feature <F9> Displays system information <F10> Saves settings and exits setup
3.2. Standard CMOS Features
ø Includes the settings for items such as date, time, floppy disk drive specifications, and
hard drives connected to the IDE interface.
n Date (mm:dd:yy)
n Time (hh:mm:ss)
n IDE Channel 0 Master(Slave) / IDE Channel 1 Master(Slave)
16
setup screen)
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
Date (mm:dd:yy) Mon, Apr, 18 2005 Time (hh:mm:ss) 11:20:24
} IDE Channel 0 Master [None] } IDE Channel 0 Slave [Non e] } IDE Channel 1 Master [None] } IDE Channel 1 Slave [Non e] } IDE Channel 2 Master [None] } IDE Channel 3 Master [None]
Drive A [1.44M, 3.5"] Drive B [Non e] Floppy 3 Mode Supo rt [Disabled]
Halt On [All, But Keybo ard]
Base Memory 640K Extended Memory 127M T otal Memory 128M
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Standard CMOS Features
Item Help Menu Level} Change the day, month, year
<Week> Sun. to Sat.
<Month> Jan. to Dec.
<Day> 1 to 31 (or maximum allowed in the month)
<Year> 1999 to 2098
Allows you to setup the date in the mm:dd:yy fashion.
Allows you to set up the date in the hh:mm:ss fashion. The time must be entered in the 24-hour format.
[IDE Device Setup]
IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. IDE Channel 0 Master(Slave) / IDE Channel 1 Master(Slave) IDE Device Setup. You can use one of three methods: Auto Allows BIOS to automatically detect IDE devices during POST(default) None Select this if no IDE devices are used and the system will skip the
Manual User can manually input the correct settings Access Mode Use this to set the access mode for the hard drive. The four options are:
Capacity Capacity of currently installed hard disk. Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.
automatic detection step and allow for faster system start up.
CHS/LBA/Large/Auto(default:Auto)
n IDE Channel 2/3 Master [IDE Device Setup]
IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. IDE Channel 0 Master(Slave) / IDE Channel 1 Master(Slave) IDE Device Setup. You can use one of two methods: Auto Allows BIOS to automatically detect IDE devices during POST(default) None Select this if no IDE devices are used and the system will skip the
automatic detection step and allow for faster system start up.
Access Mode Use this to set the access mode for the hard drive. The four options are:
CHS/LBA/Large/Auto(default:Auto) Capacity Capacity of currently installed hard disk. Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.
n Drive A/B
Allows user to configure the type of floppy drive his/she installs. Options: None (No floppy drive installed)
360K, 5.25" (5.25 inch PC-type high-density drive; 360K bytes capacity.)
1.2M, 5.25" (5.25 inch AT-type high-density drive; 1.2M bytes capacity.) 720K, 3.5" (3.5 inch double-sided drive; 720K bytes capacity.)
1.44M, 3.5" (3.5 inch double-sided drive; 1.44M bytes capacity.)
2.88M, 3.5" (3.5 inch double-sided drive; 2.88M bytes capacity.)
n Floppy 3 Mode Support
Allows user to configure a Japanese standard 3 Mode floppy drive. Options: Disabled (No 3 Mode drive installed)
Drive A (3 Mode Drive installed in A:) Drive B (3 Mode Drive installed in B:) Both (3 Mode Drive installed in A: and B:)
n Halt on
Tells the BIOS specifically which types of errors will halt the computer during the power­on self test (POST) section of the boot. Options: No Errors (Never halt when an error is detected)
All Errors (Halt whenever an error is detected) All, But Keyboard (Halt whenever an error is detected with the exception of the keyboard) All, But Diskette (Halt whenever an error is detected with the ex ception of the diskette) All, But Disk/Key (Halt whenever an error is detected with the exception of the diskette and keyboard) (default:All, But Keyboard)
n Memory
When BIOS is displayed during POST, memory capacity is also displayed as shown below: Base Memory, Extended Memory, Total Memory (the user can verify the accuracy of these values)
English
17
English
ø Allows the configuration of advanced settings such as boot sequence, password
3.3. Advanced BIOS Features
check, etc.
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
} Hard Disk Boot Priority [Press Enter]
First Boot Device [Floppy] Second Boo t Device [Hard Disk] Third Boot Device [C DROM] Password Check [Setup] CPU Hyper-Threading Limit CPUID Max. to 3 [Disabled] No-Execute Memory Pro tect CPU Enhanced Halt (C1E) CPU Thermal Monitor 2(TM2) Init Display First [AGU] On-Chip Frame Buffer Size [16MB]
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
#
(Note)
(Note)
(Note)
Advanced BIOS Features
[Enabled]
[Disabled] [Disabled] [Disabled]
Item Help Menu Level} Select Boo t Device priority
[Floppy] Boot from floppy
[LS120] Boot fro m LS120
[HDD-0] Boot from First HDD
[HDD-1] Boot from Second HDD
" # " If the installed CPU is an Intel Pentium 4 CPU supporting Hyper-Threading Technology, the system will automatically provide this option.
n Hard Disk Boot Priority
The user can select the boot order for hard disks connected to onboard IDE, SATA, SCSI, RAID controllers or other add-on cards.
n First / Second / Third Boot Device
The user can select the order in which the system will boot. Options: Floppy, LS120,Hard Disk, CDROM, ZIP,USB-FDD, USB-ZIP, USB-
CDROM, USB-HDD, LAN, Disabled
n Password Check
Allows user to set a password. To remove the password entry requirement, enter SETUP and make sure there is no entry and then press <Enter>. Options: System (Password entry is required during system start up and to enter
CMOS SETUP) Setup (Password entry is required to enter CMOS SETUP)(default:Setup)
n CPU Hyper-Threading #
Allows user to enable the CPU Hyper-Threading function, of which must also be supported by the operating system. (default: Enabled)
n Limit CPUID Max. to 3
This option will be available when you install an Intel Prescott processor. Enable this item when you install old operating systems (example:NT 4.0) (default: Disabled)
(Note) If the installed CPU supports this function, the system will automatically provide this option.
18
English
n No-Execute Memory Protect
(Note)
Allows user to enable the No-Execute Memory Protect function. (default: Disabled)
n CPU Enhanced Halt (C1E)
Allows user to enable the CPU Enhanced Halt (C1E) function. (default: Disabled)
n CPU Thermal Monitor 2(TM2)
(Note)
(Note)
Allows user to enable the CPU Thermal Monitor 2(TM2) function. (default: Disabled)
n Init Display First
Allows you to select whether to boot the system using the AGP graphics card or the PCI graphics card. Options: AGU (boot using AGU graphics card)
Onboard (boot using onboard AGP) PCI(boot using PCI graphics card). (default: AGU)
n On-Chip Frame Buffer Size
Allows user to set the size of the on-chip frame buffer. Options: 1MB/4MB/8MB/16MB/32MB (default:16MB)
3.4. Integrated Peripherals
ø This menu allows you to control the various ports of the computer such as IDE,
SATA, USB, IEEE1394, COM port, LPT port, AC97 audio, etc.
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
On-Chip Primary PC I IDE [Enabled] On-Chip Secondary PCI IDE [Enabled]
On-Chip SATA [Auto]
x SATA Port0 Configure as SATA Port0 x SATA Port1 Configure as SATA Port1
USB Contro ller [Enabled]
USB 2.0 Con troller [Enabled]
USB Keyboard Su pport [Disabled]
USB Mouse Sup port [Disabled]
AC97 Audio [Auto]
Onboard H/W LAN [Enabled]
POWER ON Function [Disabled]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Parallel Port [378/IRQ7]
Parallel Port Mode [PRINTER]
x ECP Mode Use DMA 3
Integrated Peripherals
Item Help Menu Level} If a hard disk controller card is used, set at Disabled
[Enabled] Enable onboard IDE PORT
[Disabled] Disable onboard IDE PORT
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
n On-Chip Primary PCI IDE
Allows the user to enable or disable the first onboard IDE channel. (default:Enabled)
n On-Chip Secondary PCI IDE
Allows the user to enable or disable the second onboard IDE channel. (default:Enabled)
(Note) If the installed CPU supports this function, the system will automatically provide this option.
19
n On-Chip SATA
English
n SATA Port0 configure as (Set SATA Mode)
n SATA Port1 configure as
n USB Controller
n USB 2.0 Controller
n USB Keyboard Support
n USB Mouse Support
n AC97 Audio
n Onboard H/W LAN
n POWER ON Function
n Onboard Serial Port 1
n Onboard Parallel Port
n Parallel Mode
20
Options: Disabled (Disable this function.)
Auto (When there is no device connected to IDE1 or IDE 2 channel, SATA will be configured as IDE mode.) Manual (Manually configure SATA mode via the "SATA Port0 configure as" option.) (default:Auto)
Options: IDE Pri. Master (Set SATA Port 0 to IDE Primary Master.)
IDE Pri. Slave (Set SATA Port 0 to IDE Primary Slave.) IDE Sec. Master (Set SATA Port 0 to IDE Secondary Master.) IDE Sec. Slave (Set SATA Port 0 to IDE Secondary Slave.) SATA Port0 (Set SATA Port 0 to SATA Port0.) (This mode is supported by only Windows XP or later operating systems) SATA Port1 (Set SATA Port 0 to SATA Port1.) (This mode is supported by only Windows XP or later operating systems) (default:SATA Port0)
The item depends on what you set for "SATA Port0 configure as."
Allows the user to enable or disable the onboard USB2.0 controller. (default:Enabled)
Allows the user to enable or disable the onboard USB2.0 (default:Enabled)
Allows user to use a USB-based keyboard (Enable if you are using a USB keyboard, otherwise Disable) (default:Disabled)
Allows user to use a USB-based mouse (Enable if you are using a USB mouse, otherwise Disable) (default:Disabled)
Allows the user to use the onboard AC97 audio (default:Auto)
Allows the user to enable or disable the onboard LAN (default:Enabled)
Allows the user to enable or disable the power on function (default:Disabled)
Allows the user to enable or disable the first onboard serial port Options: Auto, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Disabled (default:3F8/IRQ4)
Allows the user to enable or disable the onboard parallel port. Options: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, Disabled (default:378/IRQ7)
Use this to select the operation mode for the parallel port. Options: PRINTER
SPP (normal)
ECP (Extended Capabilities Port) EPP1.9+ECP (both EPP and ECP) EPP1.9+SPP (both EPP and SPP) EPP1.7+ECP (both EPP and ECP) EPP1.7+SPP (both EPP and SPP) (default:PRINTER)
n ECP Mode Use DMA
Allows the user to select the ECP Mode Use DMA Options: 1, 3, Disabled (default:3)
3.5. Power Management Setup
ø This is used to control the various power saving features of the PC.
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
ACPI Suspend Type [S1(POS)] Power LED in S1 State [Blinking] Off by Power button [Instant-Off] AC Back Function [Soft-Off] PME Event Wake Up [Enabled] ModemRingOn/WakeOnLan [Enabled]
Resume by Alarm [Disabled]
x Date (of Month) Alarm Everyday x Time (hh:mm:ss) Alarm 0 : 0 : 0
Power Management Setup
Item Help Menu Level} [S1] Set suspend type to Power On Susp end under ACPI OS
[S3] Set suspend type to Suspend to RAM under ACPI OS
English
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
n ACPI Suspend Type
Allows user to select the Advanced Configuration and Power Interface(ACPI) as S1/ POS (Power On Suspend) or S3/STR(Suspend To RAM) (default:S1/POS)
n Power LED in S1 state
Allows user to select the system LED status in the S1 (POS - Power On Suspend) state. Options: Blinking (LED will blink)
Dual/OFF (When selecting this, the LED will turn off for a single-colored LED or change color for a dual-colored LED)(default:Blinking)
n Off by Power button
Controls whether the PC shuts off immediately after hitting the power button or delaying a few seconds. (default:Instant-off) Options: Instant-off (PC shuts off immediately)
Delay 4 Sec. (PC shuts off after a 4sec. delay)
n AC Back Function
Allows user to select system status when power is removed and returned. Options: Memory (return prior to power removal)
Full-On (return to full system power) Soft-Off (use of Soft PWR button to power on system)(default:Soft-Off)
21
n PME Event Wake Up
English
n ModemRingOn/WakeOnLan
n Resume by Alarm
3.6. PnP/PCI Configuration
ø This menu allows you to configure your PCI slots. You can assign IRQ's for various PCI
Allows user to select the Power Management Event (PME) wake up function which requires the system to have a +5VSB power supply using a rate of 1A or less. (default:Enabled)
To use this feature, an Ethernet card supporting the PCI2.2 or newer standard must be used. (default:Enabled)
If set to Enabled, the user can set the date and time for automatic system power-on. (default:Disabled) Settings: Date (of Month) Alarm : Everyday, 1~31 Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)
slots.
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
PCI 1 IRQ Assignment [Auto] PCI 2 IRQ Assignment [Auto] PCI 3 IRQ Assignment [Auto]
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
PnP/PCI Configurations
Item Help Menu Level} Device(s) using this INT:
IDE C ntrlr
-Bus 0 Dev 31 Func 2 USB 1.1 Ho st cntrlr
-Bus 0 Dev 29 Func 2
n PCI 1 IRQ Assignment
Allows you to assign an IRQ for the first PCI slot. Options: Auto,3,4,5,7,9,10,11,12,14, 15 (default:Auto)
n PCI 2 IRQ Assignment
Allows you to assign an IRQ for the second PCI slot. Options: Auto,3,4,5,7,9,10,11,12, 14,15 (default:Auto)
n PCI 3 IRQ Assignment
Allows you to assign an IRQ for the third PCI slot. Options: Auto,3,4,5,7,9,10,11,12,14, 15 (default:Auto)
22
3.7. PC Health Status
ø This menu displays the current CPU temperature, the fan speeds, voltages etc.
English
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
Curren t CPU Temperature 45°C Current System Temperatu re 30°C Vcore 1.78V DDR25V 2.544V +3.3V 3.36V +5V 5.14V +12V 11.84V Current CPU FAN Speed 4440 RPM Curren t SYSTEM FAN Speed 0 RPM
CPU Smart FAN Control [Enabled] CPU Smart FAN Mode [Auto]
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
PC Health Status
Item Help Menu Level}
n Current CPU / System Temperature
Automatically checks CPU & System temperature
n Current Voltage(V) Vcore / DDR25V / +3.3V / +5V / +12V
Automatically checks system voltage
n Current CPU / SYSTEM FAN Speed (RPM)
Automatically checks CPU/SYSTEM fan speed.
n CPU Smart FAN Control
Allows users to enable or disable the CPU Smart FAN Control function. (default: Enabled) With this item set to enabled, CPU fan changes speed depending on CPU temperature.
n CPU Smart FAN Mode
Allows users to set the CPU Smart FAN mode when CPU Smart FAN Control is set to Enabled. (default: Auto) Options: Auto (BIOS autochecks which type of CPU fan is installed and sets the
optimcal CPU Smart FAN control mode.) Voltage (Set this item to Voltage if a 3-pin CPU fan is installed.) PWM (Set this item to PWM if a 4-pin CPU fan is installed.)
Note: In fact, you can set the CPU Smart Fan Control mode to Voltage for either 3-
pin or 4-pin CPU fan. However, for those 4-pin CPU fans that are not designed following Intel's 4-wire fans PWM control specifications, setting the CPU Smart Fan Control mode to PWM may not effectively reduce the CPU fan speed.
23
English
ø This allows user to configure CPU frequency and voltage settings.
3.8. Frequency/Voltage Control
CMOS Setup Utility-Copyright (C ) 1984-2005 Award Software
CPU Clock Ratio [15X] Memory Frequency For [Auto]
Memory Frequency (Mhz) 266
higf: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Frequency /Voltage Control
Item Help Menu Level} Set CPU Ratio if CPU Ratio is unlocked
n CPU Clock Ratio
Allows user to set the CPU Clock Ratio. If the CPU used locks this feature, then it will not be displayed or will not function. (based on CPU type)
n Memory Frequency For
Allows user to set memory frequency (default:Auto) for FSB(Front Side Bus) frequency=533MHz,
2.0 Memory Frequency = Host clock X 2.0.
2.5 Memory Frequency = Host clock X 2.5. Auto Set Memory frequency by DRAM SPD data. for FSB(Front Side Bus) frequency=800MHz,
2.0 Memory Frequency = Host clock X 2.0.
1.66 Memory Frequency = Host clock X 1.66.
1.33 Memory Frequency = Host clock X 1.33. Auto Set Memory frequency by DRAM SPD data.
n Memory Frequency (Mhz)
The memory frequency is based on the " Memory Frequency For" setting.
24
3.9. Load Fail-Safe Defaults
ø Use this option to reset your BIOS settings to the system defaults. You should only use
this if you are encountering serious problems. Please select <Y> and <Enter> to load Fail-Safe defaults. Once this is loaded, your system may be slowed since this uses a minimal performance setting to allow stable system running.
3.10. Load Optimized Defaults
ø Like the Fail-Safe mode above, this option loads the BIOS default settings, but runs the
system at optimal performance. Please select <Y> and <Enter> to load optimized defaults.
3.11. Set User Password
ø Use this to set the password that is needed to either enter into the BIOS or to boot the
system. Entering in a blank field will disable the password. Please input an 8 character long password and then select Enter. You will be required to re-enter the password for confirmation. If you wish to remove the need for password entry, leave the entry blank and then select Enter. BIOS will then display "PASSWORD DISABLED". Once you have completed the password setting, you will need to go to "Advanced BIOS Features" and select "Password Check" for setup of password check.
3.12. Save & Exit Setup
ø To save any changes you made to the BIOS you must choose this option. The
system will automatically exit setup and perform a system restart. Pushing <F10> will have the same effect. Push <Y> and <Enter> to save and exit setup. If you do not wish to save, select <N> or <Esc> to return to the main menu.
English
3.13. Exit Without Saving
ø Use this option instead of the one above if you wish to exit the BIOS without saving the
changes you have made. Pushing <ESC> will have the same effect. Push <Y> and <Enter> to exit setup. You can return to the main menu by pushing <N>or <Esc>.
25
English
4. Driver Installation
Driver installation for the Windows 98/98SE/2000/ME/XP operating systems is simple. Once you insert the provided driver disks into your optical drive, the AUTORUN screen will appear. If this screen does not appear, you can use "D:\setup.exe" (with "D" being the specified drive) to bring up the screen shown below. Just follow the screen instructions to easily complete driver installation.
Open User Manual Display system information Open Readme File Browse CD Contact Us
axper Install -Displays required driver installation, select "Go" for
automatic installation Customize Installation - Allows specific choice of drivers for installation axper Utilities - Displays axper's unique utilities Software - Displays the required software
26
Loading...