Intel WM3B2100, WM3A2100 OEM Notice Information

Calexico Compliance Document

Compliance Notices

Source Document for OEMs

Calexico

Mobile Communications Division

Authors: Paul Straley, Tony Lukyn

Created: 09/25/02

Last Updated: 12/20/02TL

Page 1 12/20/02

Calexico Compliance Document

Revision History

Date Changes

09/25/02 Created document
10/03/02 Corrected errors in document, added 3 additional Mini PCI models,

genericized product references to refer to “LAN Mini PCI Adapters”
10/08/02 Added Annex II under 1999/5/EC for 2.4 GHz products (PS)
12/18/02 Added “Information for the OEM” page 1 and additional text for

OEM integrators page 4 (TL)
12/20/02 Added End Product Label: FCC ID “XXXXXXXX’ info.

Page 2 12/20/02

Calexico Compliance Document

Intel(R) PRO/Wireless LAN 7100 and 2100 Mini PCI Adapters
Safety and Regulatory Notices

This device is intended for OEM integrators only.
This device cannot be co-located with any other transmitter.

Information for the OEM Integrators:

Please refer to the full Grant of equipment document for other restrictions.

The following regulatory and safety notices must be published in compliance with local regulations.

Note:

This information applies to the following products:

Intel(R) PRO/Wireless LAN 7100 3B Mini PCI Adapter (model WM3B7100; dual 802.11a and 802.11b)
Intel(R) PRO/Wireless LAN 7100 3A Mini PCI Adapter (model WM3A7100; dual 802.11a and 802.11b)
Intel(R) PRO/Wireless LAN 2100 3B Mini PCI Adapter (model WM3B2100; 802.11b only)
Intel(R) PRO/Wireless LAN 2100 3A Mini PCI Adapter (model WM3A2100; 802.11b only)

Local Restriction of 802.11a and 802.11b Radio Usage

The following statement on local restrictions must be published as part of the compliance documentation for all 802.11a and

802.11b products.

Caution:

countries, 802.11a and 802.11b products are designed for use only in specific countries, and are not allowed to be operated in
countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are
used only in the countries for which they were intended and for verifying that they are configured with the correct selection of
frequency and channel for the country of use. Any deviation from permissible settings and restrictions in the country of use could be
an infringement of national law and may be punished as such.

Due to the fact that the frequencies used by 802.11a and 802.11b wireless LAN devices may not yet be harmonized in all

USA and Canada Safety Requirements and Notices

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF)
electromagnetic energy emitted by FCC certified equipment. The Intel PRO/Wireless LAN Mini PCI Adapter products meet the
Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the
instructions found in this manual will result in exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:

• Do not touch or move antenna while the unit is transmitting or receiving.

• Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body,

especially the face or eyes, while transmitting.

• Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.

• Use in specific environments:

o The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such

environments.

o The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).
o The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.

• Antenna use:

o In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of

20 cm (8 inches) or more from the body of all persons.

o High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a

minimum distance of 30 cm (12 inches) or more from the body of all persons. Please contact your professional installer,
VAR, or antenna manufacturer for proper installation requirements.

Explosive Device Proximity Warning

Warning:

explosive environment unless the device has been modified to be qualified for such use.

Antenna Warning

Warning:

Adapters installed in a desktop or portable computer, that the antenna for this device be installed so as to provide a separation
distance of al least 20 cm (8 inches) from all persons and that the antenna must not be co-located or operating in conjunction with
any other antenna or radio transmitter. It is recommended that the user limit exposure time if the antenna is positioned closer than
20 cm (8 inches).

Use On Aircraft Caution
Caution:

could interfere with critical aircraft instruments.

Other Wireless Devices

Safety Notices for Other Devices in the Wireless Network:

or other devices in the wireless network.

Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an

To comply with the FCC and ANSI C95.1 RF exposure limits, it is recommended for Intel(R) PRO/Wireless LAN Mini PCI

Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals

Refer to the documentation supplied with wireless Ethernet adapters

Page 3 12/20/02