Intel SBFCM, SBCEFCSW User Manual

Intel® Blade Server Fibre Channel Switch Module SBCEFCSW and Fibre Channel Expansion Card SBFCM: Hardware Maintenance Manual and Troubleshooting Guide

A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies & Products

Order Number C46558-003

NOTE Before using this information and the product it supports, be sure to read the general information in “Safety and regulatory information” on page iii.

Disclaimer

Information in this document is provided in connection with Intel. products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's T erms and Conditions of Sale for such products.

Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, m e rchantability, or infringement of any patent, copyright or other intellectual property right.

Intel products are not designed, intended or authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of the Intel product could create a situation where personal injury or death may occur. Intel may make changes to specifications and product descriptions at any time, without notice.

Intel, Pentium, Itanium and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

ii Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Safety and regulatory information

✏ NOTE

The service procedures are designed to help you isolate problems. They are written with the assumption that you have model-specific training on all computers, or that you are familiar with the computers, functions, terminology, and service information provided in this manual.

iii

General Safety

Follow these rules to ensure general safety:

• Observe good housekeeping in the area of the machines during and after maintenance.

• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.

• Place removed cov ers and other parts in a safe place, a w ay from all personnel, while you are servicing the machine.

• Keep your tool case away from walk areas so that other people will not trip over it.

• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end.

• Do not wear jewelry , chains, metal-frame eyeglasses, or metal fasteners for your clothing. Remember: Metal objects are good electrical conductors.

• Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.

• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.

• Reinstall all covers correctly before returning the machine to the customer.

Electrical Safety

CAUTION:

Important: Observe the following rules when working on electrical equipment:

• Disconnect all power before performing a mechanical inspection.

• Before you start to work on the machine, unplug the power cord. or power-of f the wall box that supplies

• Regularly inspect and maintain your electrical hand tools for safe operational condition.

• Do not use worn or broken tools and testers.

• Never assume that power has been disconnected from a circuit. First, check that it has been powered-off.

• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,

• Do not touch live electrical circuits with the reflective surface of an inspection mirror. The surface is

Electrical current from power, telephone, and communication cables can be h azard ou s. To avoid personal injury or equipment damage, disconnect the server system power cords, telecommunication systems, networks, and modems before you open the server covers.

power to the machine and to lock the wall box in the off position.

nongrounded power extension cables, power surges, and missing safety grounds.

conductive; such touching can cause personal injury and machine damage.

iv Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Handling electrostatic discharge-sensitive devices

Any computer part containing transistors or integrated circuits (IC) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the server , the part, the work mat, and the person handling the part are all at the same charge.

✏ NOTE

Use product-specific ESD procedures when they exceed the requirements noted here.

Make sure that the ESD-protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.

• Avoid contact with other people.

• Wear a grounded wrist strap against your skin to eliminate static on your body.

• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.

• Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

• Select a grounding system, such as those in the following list, to provide protection that meets the specific service requirement.

— Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. — Use an ESD common ground or reference point when working on a double-insulated or battery-

operated system. You can use coax or connector-outside shells on these systems.

— Use the round ground-prong of the AC plug on AC-operated computers.

✏ NOTE

The use of a grounding system is desirable but not required to protect against ESD damage.

CAUTION:

If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not:

• Throw or immerse into water

• Heat to more than 100×C (212×F)

• Repair or disassemble

• Dispose of the battery as required by local ordinances or regulations.

CAUTION:

When laser products (such as CD-ROMs, DVD-ROM drives, fi ber optic devices, or transmitters) are installed, note the following:

• Do not remove the covers. Remo ving the cov ers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.

• Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

Danger: DANGER

Danger: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:

Danger: Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

CAUTION:

Hazardous energy is present when the blade is connected to the power source. Always replace the blade cover before installing the blade.

Regulatory specifications and disclaimers

Safety compliance

USA: UL 60950 - 3rd Edition/CSA 22.2. No. 60950 Canada: cUL certified - 3rd Edition/CSA 22.2. No. 60950- for Canada (product bears the single

cUL mark for U.S. and Canada)

Europe: Low Voltage Directive, 73/23/EEC

UL/CB to EN60950 3rd Edition

International: UL/CB to IEC 60950 3rd Edition

UL/CB - EN60 950 3rd Edition UL/CB - EMKO-TSE (74-SEC) 207/94

Australia/New Zealand:

CB Report to IEC 60950, 3rd Edition plus international deviations

vi Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Electromagnetic compatibility (EMC)

USA: FCC CFR 47 Part 2 and 15, Verified Class A Limit Canada: IC ICES-003 Class A Limit Europe: EMC Directive, 89/336/EEC

EN55022, Class A Limit, Radiated & Conducted Emissions EN55024 ITE Specific Immunity Standard EN61000-4-2 ESD Immunity (Level 2 Contact Discharge, Level 3 Air Discharge) EN61000-4-3 Radiated Immunity (Level 2) EN61000-4-4 Electrical Fast Transient (Level 2) EN61000-4-5 AC Surge EN61000-4-6 Conducted RF EN61000-4-8 Power Frequency Magnetic Fields

EN61000-4-11 Voltage Dips and Interrupts Japan: VCCI Class A ITE (CISPR 22, Class A Limit) Australia/New

Zealand: Taiwan: BSMI Approval Korea: RRL Approval

AS/NZS 3548, Class A Limit

Russia: GOST Approval International: CISPR 22, Class A Limit

Electromagnetic compatibility notice (USA)

This equipment has been tested and found to comply with the limits for a Class A digital device, puruant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

vii

Electromagnetic compatibility notices (International)

Europe (CE Declaration of Conformity): This product has been tested in accordance to, and complies with the Low Voltage Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate its compliance.

Japan EMC Compatibility:

English translation of the notice above: This is a Class A product based on the standard of the Voluntary

Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

ICES-003 (Canada): Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: "Appareils Numériques", NBM-003 édictée par le Ministre Canadian des Communications.

English translation of the notice above: This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled "Digital Apparatus", ICES-003 of the Canadian Department of Communications.

BSMI (Taiwan): The BSMI Certification number and the following warning is located on the product safe ty label which is located visibly on the external chassis.

viii Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

RRL Korea:

English translation of the pre vio us notice:

Device User’s Information

Class A device This device complies with RRL EMC and is operated

Class B device This device complies with RRL EMC and is operated

Remarks: Class A device - operated in a commercial area. Class B device - operated in a residential area.

in commercial environment so that distributors or users pay attention to this point.

If the product is sold or purchased improperly, please exchange this product to what can be used at home.

in a residential area so that it can be used at all other location as well as residential area.

x Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Contents

Safety and regulatory information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

General Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Electrical Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Handling electrostatic discharge-sensitive devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Regulatory specifications and disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Safety compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Electromagnetic compatibility notice (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Electromagnetic compatibility notices (International) . . . . . . . . . . . . . . . . . . . . . . . . . viii

1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Related publications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Notices used in this book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2Intel

Blade Server Fibre Channel Switch Module SBCEFCSW . . . . . . . . . . . . . . . . . . . . 3

Command line interface (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Logging on to a switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Command syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Admin command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Alias command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Config command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Date command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Fallback command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Help command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

History command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Image command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Lip command (for external ports only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Passwd command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Ps command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Quit command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Reset command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Set command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Set Config command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Set Log command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Set Port command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Set Setup command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Show command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Show Config command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Show Log command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Show Perf command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Show Setup command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Shutdown command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Test command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Uptime command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

User command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Whoami command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Zone command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Zoneset command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Zoning command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Using the SAN Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

SAN Utility user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Menu bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Fabric tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Graphic window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Data window and tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Working status indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Using the Topology window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Fibre Channel switch module and link status. . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Working with switch modules and links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Topology data window tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Using the Faceplate window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Opening the Faceplate window and pop-up menus. . . . . . . . . . . . . . . . . . . . . . 76

Port views and status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Working with ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Faceplate data window tabs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Managing fabrics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Setting up security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Managing the fabric database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Displaying fabric information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Zoning a fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Using the Zoning Config window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Restoring default zoning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Merging fabrics and zoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Using the Edit Zoning window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Managing zone sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Managing zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Managing aliases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Managing switch modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Displaying switch module information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Managing alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Exporting name server information to a file . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Paging a switch module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Resetting a switch module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Configuring a switch module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Network properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Archiving a switch module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Managing firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Managing ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Displaying port information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Configuring ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Switch management utility functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

LED diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Heartbeat LED patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Switch module fault LED flash pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Switch module OK LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Port logged-in LED flash patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Port fault LED flash patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Port testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

xii Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Fibre Channel switch module monitoring using SNMP. . . . . . . . . . . . . . . . . . . . . . . 118

SNMP configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

SNMP trap configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Restoring Fibre Channel switch module configuration . . . . . . . . . . . . . . . . . . . . . . . 119

Configuration backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Configuration restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Restoring the factory default configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Reinitializing the configuration file system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Restoring a switch module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Using the Fabric View application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Starting the Fabric View application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Displaying port performance graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Arranging and sizing port performance graphs . . . . . . . . . . . . . . . . . . . . . . . . 122

Customizing port performance graphs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Mapping port locations and software numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Port mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

3Intel

Server FC Expansion Card SBFCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Features and specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Inventory checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Notices and statements used in this book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Major components of the SBFCM Expansion Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Installing the Expansion Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Handling static-sensitive devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Installing the Expansion Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Using Fast!UTIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Starting Fast!UTIL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Configuration Settings menu options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Select host adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Host Adapter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Selectable Boot Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Restore Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Raw NOVRAM data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Advanced Adapter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Extended Firmware Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Scan Fibre Channel devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Fibre Channel disk utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Loopback data test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

ExitFast!UTIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

4 Diagnostic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

General Fibre Channel configuration diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

General Checkout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Hardware problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Software problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

System configuration problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Fibre channel problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

5 Symptom-to-FRU index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Fast!UTIL utility status codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Switch error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Expansion card error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Contents xiii

Management module error messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Switch diagnostic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

LED error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

I2C diagnostic register definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Undetermined problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Problem determination tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

6 SBCEFCSW / SBFCM Parts listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Intel

Blade Server Switch Module SBCEFCSW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Blade Server Fibre Channel Expansion Card SBFCM . . . . . . . . . . . . . . . . . . . . . . 154

Intel

A Getting help and technical assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Before you call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Using the documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

xiv Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

1 General information

Fibre Channel technology is outlined in the SCSI-3 Fibre Channel Protocol (SCSI-FCP) standard. Fibre Channel is a high-speed data transport technology used for mass storage and networking.

By adding Fibre Channel Expansion Cards to the blade servers and Fibre Channel switch modules to the Intel Blade Server Chassis SBCE, you can attach the blade server to an external storage area network (SAN) through the external 2 Gbps (gigabits per second) optical ports on the switch modules. The Fibre Channel Expansion Card supports data-transfer rates up to 200 MB per second half-duplex and 400 MB per second full-duplex.

Related publications

This Hardware Maintenance and Troubleshooting Guide contains information to help you slve problems yourself or to provide helpful information to a service technician. In addition to this guide, the following related documentation is provided with your switch module:

• Intel

• QLogic

Blade Server Switch Module SBCEFCSW Management and User’s Guide

This publication is provided in Portable Document Format (PDF) on the Intel

Blade Server Switch

Module SBCEFCSW Reource CD. It describes how to use the SAN Utility application, describes how to

start the Telnet CLI, and lists the CLI commands and their usage.

Blade Server Chassis SBEFCSW Installation Guide

This publication is provided in Portable Document Format (PDF) on the Resource CD. It contains installation and setup instructions for your switch module. It also provides general information about your switch module, including getting started, configuring your switch module, and how to access and use online help.

Blade Server Compute Switch Module SBCFM Installation and User’s Guide

This publication is provided in PDF on the Resource CD. It contains instructions for installing the Intel Fibre Channel Expansion card into an Intel Blade Server Compute. This publication contains information about

— Installing and configuring the expansion card — Updating the BIOS and device drivers of the expansion card

SAN Solutions Guide

This publication is provided in PDF on the Resource CD. It provides a user-oriented discussion of how Fibre Channel options are used to provide different SAN storage solutions for various application requirements. This document also provides an overview and description for backup and restore, business continuance and high availability, and storage consolidation and data sharing solutions.

Switch Interoperability Guide

This publication is provided in PDF on the Resource CD. It provides detailed Fibre Channel switch configuration data and step-by-step configuration procedures for integrating the Blade Server Chassis SBCE into other vendor switch fabrics. Each vendor configuration includes:

— An initial integration checklist — Configuration limitations — Supported switch and firmware versions — Specific management application operations — A successful-integration checklist.

• QLogic® SAN Interoperability Guide

This publication is provided in PDF on the Resource CD. It is a key resource for SAN planning and implementation. It provides interoperability matrices that let you identify at a glance the certified SAN products, solutions, and services that best suit your needs.

• QLogic

This publication is provided in PDF on the Resource CD. It is a comprehensive guide for those interested in deploying QLogic and CLARiion Storage solutions.

• QLogic This publication is provided in PDF on the Resource CD. It is a comprehensive guide for those interested

in deploying QLogic and LSI Storage solutions.

• QLogic

This publication is provided in PDF on the Resource CD. It is a comprehensive guide for those interested in deploying QLogic and XIOtech Storage solutions.

• Intel This multilingual publication is provided in PDF on the Resource CD. It contains translated versions of

the caution and danger statements that appear in the documentation.

SAN Configuration Guide: CLARiiON Storage

SAN Configuration Guide: LSI Storage

SAN Configuration Guide: XIOtech Storage

Server Boards and Server Chassis Safety Information

Notices used in this book

The following notices are used in this book:

• Notes: These notices provide important tips, guidance, or advice.

• Important: These notices provide information or advice that might help you avoid inconvenient or problem situations.

• Attention: These notices indicate potential damage to programs, devices, or data. An attention notice is placed just before the instruction or situation in which damage could occur.

2 Intel Blade Swerver Switch Module SBCEFCSW / FC Expansion Card SBFCM: HMM and Troubleshooting Guide

2 Intel® Blade Server Fibre Channel Switch

Module SBCEFCSW

✏ NOTE

Throughout this publication, the phrases "switch module" and "fibre channel switch module" refer to the Intel

You can manage and configure your Intel Telnet connection to the embedded command line interf ace (CLI) or b y using the SAN Utility application. The SAN Utility provides an intuitive graphical user interface (GUI) that you can use to configure multiple fibre channel switch modules through other connected SAN devices from a single interface. The SAN Utility application is referred to throughout this publication as the S AN Utility.

This guide provides instructions to:

• Configure your switch module

• Manage fabrics, ports, and switch modules

• Use Telnet and the CLI to configure switch module parameters

You can manage the SBCE fabric through an Ethernet network using the SAN Utility or the CLI. The SAN Utility is installed on a Microsoft* Windows* 2003, Red Hat* Linux* Advanced Server Version 2.1 or Red Hat Linux Version 9.0.

The switch module has an embedded Telnet server through which a Telnet client can connect and manage the switch module using the CLI. See “Command line interface (CLI)” below for more information about Telnet and CLI commands.

SNMP provides monitoring and trap functions for the fabric. The switch module firmware supports SNMP Versions 1, 2, and 3; the Fibre Alliance Management Information Base (FA-MIB) version 4.0; and the Fabric Element Management Information Base (FE-MIB) RFC 2837. Traps are formatted using SNMP version 2.

If you are an experienced user, you can use the Telnet CLI to perform the following tasks:

• Manage the switch module from the SBCE management module interface to the Telnet client

• Perform single switch management

• Use advanced control commands

If you are a new user or if you need to manage multiple switch modules from a single interface, you can use the SAN Utility GUI to perform the following tasks:

• Manage your switch module from a remote client or network management workstation

• Manage your multiswitch fabric

For information about installing the switch module and the SAN Utility, see the Switch Module Installation Guide that comes with the switch module.

Blade Server Fibre Channel Switch Module SBCEFCSW.

Blade Server Fibre Channel Switch Module SBCEFCSW through a

Command line interface (CLI)

Your switch module contains an embedded Telnet server. This server enables a Telnet client to establish a Telnet session with the switch module to retrieve information or to configure parameters using the CLI. You can use the CLI to perform a variety of fabric and switch management tasks through an Ethernet connection to

your Intel You can access the Telnet interface in two ways:

• In the Blade Server Chassis SBCE management module Web interface

• In a command-line window on a connected network management workstation

Important: Before you configure your switch module, be sure that the management modules in your Blade Server Chassis SBCE are properly configured. In addition, to access and manage your switch module from an external environment, you might need to enable certain features, such as the external ports and external management over all ports. See the applicable SBCE Installation and User’s Guide publications on the Resource CD for more information. For more detailed information about configuring your switch module, see the Fibre Channel Switch Module Installation Guide on the Resource CD.

Logging on to a switch

To log on to a switch using Telnet, complete the following steps:

1. Open a command-line window on the network management workstation, type one of the following

2. At the Login prompt, type the initial default user ID, USERID. At the Password prompt, type the initial

This user account provides full access to the switch and its configuration. After planning your fabric management needs and creating your own user accounts, consider changing the password for this account. See “Commands” for more information about authority levels. See the “User command” on page 58 for information about creating user accounts.

Blade Server Chassis SBCE.

commands, and press Enter. For switch module bay 3:

telnet 192.168.70.129

For switch module bay 4:

telnet 192.168.70.130

A command prompt window opens.

default password, PASSW0RD (the sixth character is a zero, not the letter O). The user ID and password are case sensitive.

✏ NOTE

The switch module supports a combined maximum of 15 logins. This includes the SAN Utility inband and out-of-band logins, Telnet out-of-band logins, and SNMP out-of-band logins. A maximum of ten SAN Utility logins are accepted. Additional logins will be refused.

4 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Command syntax

The command syntax is as follows:

command

word

key keyword [value] keyword [value1] [value2]

The command is followed by one or more keywords. Consider the following rules and conventions:

• Commands and keywords are lowercase and case sensitive.

• Required keyword values are shown in standard font: [value]. Optional values are shown in italics: [value].

• The underlined portion of each keyword indicates the abbreviated form that can be used. F or e xample the

ete keyword can be abbreviated Del.

Del

Commands

The command set provides for User and Admin authority levels.

• User authority grants viewing access to the fabric and switches using the Show command and other readonly commands.

• Admin authority includes the User authority and grants permission to use the Admin command. The Admin Start command opens an admin session, which provides access to the commands that change switch and fabric configurations. See the “ Admin command” on page 7.

✏ NOTE

Admin authority is enforced only if fabric security is enabled on the switch. By default, fabric security is disabled. See the keywords of the “Set Setup command” on page 35 for information about setting fabric security.

The commands and their page numbers are listed by authority level in Table 1. The following Admin session commands have some keywords that are available with User authority:

Alias Config Date Set User Zone Zoneset Zoning

Table 1. Commands listed by authority level

User authority commands Admin authority command

Help “Help command” on page 14. History “History command” on page 15. Ps “Ps command” on page 19. Quit “Quit command” on page 20. Show “Show command” on page 38. Show Config “Show Config command” on page

45. Show Log “Show Log command” on page 48. Show Perf “Show Perf command” on page 50. Show Setup “Show Setup command” on page

52. Uptime “Uptime command” on page 57. Whoami “Whoami command” on page 60

Admin “Admin command” on page 7

Admin session commands

Alias “Alias command” on page 8. Config “Config command” on page 10. Date “Date command” on page 12. Fallback “Fallback command” on page 13. Image “Image command” on page 16. Lip “Lip command (for external ports

only)” on page 17. Passwd “Passwd command” on page 18. Reset “Reset command” on page 20. Set “Set command” on page 24. Set Config “Set Config command” on page 26. Set Log “Set Log command” on page 32. Set Port “Set Port command” on page 34. Set Setup “Set Setup co mmand” on page 35. Shutdown “Shutdown command” on page 54. Test “Test command” on page 55. User “User command” on page 58. Zone “Zone command” on page 61. Zoneset “Zoneset command” on page 64. Zoning “Zoning comma nd” on page 66

6 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Admin command

Opens and closes an admin session. The admin session provides commands that change the fabric and switch configurations. Only one admin session can be open on the switch at any time. An inactive admin session will time out after a period of time that can be changed using the Set Setup System command. See the “Set Setup command” on page 35.

Authority

Admin

Syntax

admin

start end cancel

Keywords

start

Opens the admin session.

end

Closes the admin session. The Logout, Shutdown, and Reset Switch commands will also end an admin session.

cancel

Terminates an admin session opened by another user. Use this keyword with care because it terminates the admin session without warning the other user and without saving pending changes.

Notes

Closing a Telnet window during an admin session does not release the session. In this case, you m ust either wait for the admin session to time out, or use the Admin Cancel command.

Examples

The following example shows how to open and close an admin session.

FCSM: user1> admin start

FCSM: (admin) user1>

. . .

FCSM (admin): user1> admin end FCSM: user1>

Alias command

Creates a named set of ports. Aliases make it easier to assign a set of ports to many zones. An alias cannot have a zone or another alias as a member.

Authority

Admin

Syntax

alias

add [alias] [members] copy [alias_source] [alias_destination] create [alias]

ete [alias]

del list members [alias] remove [alias] [members] rename [alias_old] [alias_new]

Keywords

add [alias] [members]

Specifies one or more ports given b y [members ] to add to the alias named [alias]. An alias can hav e a maximum of 2000 members. [members] can have one of the following formats:

• Domain ID and port number pair (domain ID, port number). Domain IDs and port numbers are in decimal format. Ports are numbered beginning with 0.

• 6-character hexadecim a l device Fibre Channel address (hex)

• 16-character hexadecimal port worldwide name (PWWN) with the format xx:xx:xx:xx:xx:xx:xx:xx.

The application verifies that the [alias] format is correct but does not validate that such a port exists.

copy [alias_source] [alias_destination]

Creates a new alias named [alias_destination] and copies the membership in to it from the alias given by [alias_source].

create [alias]

Creates an alias with the name given by [alias]. An alias name must begin with a letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, &, _, and -. The zoning database supports a maximum of 256 aliases.

ete alias

del

Deletes the specified alias given by [alias] from the zoning database. If the alias is a member of the active zone set, the alias will not be removed from the active zone set until the active zone set is deactivated.

list

Displays a list of all aliases. This keyword is valid for User authority and does not require a zoning edit session or an admin session.

members [alias]

Displays all members of the alias given by [alias]. This keyword is available with User authority and does not require a zoning edit session or an admin session.

8 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

remove [alias] [members]

Removes the ports given b y [members] from the alias given by [alias]. [members] can ha ve one of the following formats:

• Domain ID and port number pair (domain ID, port number). Domain IDs and port numbers are in decimal format. Ports are numbered beginning with 0.

• 6-character hexadecim a l device Fibre Channel address (hex)

• 16-character hexadecimal port worldwide name (PWWN) for the device with the format xx:xx:xx:xx:xx:xx:xx:xx.

rename [alias_old] [alias_new]

Renames the alias given by [alias_old] to the alias given by [alias_new].

Config command

Manages the Fibre Channel configurations on a switch. For information about setting the port and switch configurations, see the “Set Config command” on page 26.

Authority

Admin for all keywords except List

Syntax

config

ivate [config]

act backup cancel copy [config_source] [config_destination]

ete [config]

del edit [config] list restore save [config]

Keywords

activate [config]

Activates the configuration given by [config]. If you omit the configuration, the currently active configuration is used. Only one configuration can be activ e at a time.

backup

Creates a file named configdata, which contains the configuration information. T o do wnload this f ile, open a File Transfer Protocol (FTP) session, log in with account name of images and password of images, and type get configdata.

cancel

Terminates the current configuration edit session without saving changes that were made.

copy [config_source] [config_destination]

Copies the configuration given by [conf ig_source] to the configuration gi v en by [conf ig_destination]. The switch supports up to 10 configurations including the default configuration.

ete [config]

del

Deletes the specified configuration file where [config] is a file name.

edit [config]

Opens an edit session for the configuration given by [config]. If you omit the configuration name, the currently active configuration is used.

list

Displays a list of all available configurations. This keyword is available with User authority.

restore

Restores configuration settings to an out-of-band switch from a backup file named configdata, which must be first uploaded on the switch using FTP. You create the backup file using the Config Backup command. Use FTP to load the backup file on a switch, and then enter the Config Restore command.

save [config]

Saves changes made during a configuration edit session in the configuration given by [config]. If you omit the configuration name value, the configuration you chose for the Config Edit command is used.

10 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Notes

If you edit the active configuration, changes will be suspended until you reacti v ate the configuration or acti v ate another configuration.

Examples

The following shows an example of how to open and close a Config Edit session.

FCSM: user1> admin start

FCSM (admin) : user1> config edit . . . FCSM (admin-config) : user1> config cancel

Configuration mode will be canceled.Please confirm (y/n): [n] y

FCSM (admin) : user1> admin end

Date command

Displays or sets the blade server date and time. To set the date and time, you must provide the information string in this format: MMDDhhmmCCYY, where MM = month, DD = day, hh = hour, mm = minute, CC = century, and YY = year. You must reset the switch for the new date to take effect.

Authority

Admin to change the date; user to display the date.

Syntax

date

[MMDDhhmmCCYY]

Keywords

[MMDDhhmmCCYY]

Specifies the date – this requires an admin session. If you omit [MMDDhhmmCCYY], the current date is displayed – this is available with User authority.

Examples

The following is an example of the Date command.

FCSM: user1> date Thu Sep 26 07:51:24 2002

12 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Fallback command

Loads the fallback version of the firmware from switch memory. The switch stores two versions of the firmware. This command alternately activates the two versions.

Authority

Admin

Syntax

fallback

Notes

• The Show Switch command displays the available firmware versions and the currently active version.

• After running the Fallback command, reset the switch for the firmware to be in effect.

Examples

The following is an example of the Fallback command.

FCSM: user1> admin start FCSM (admin) : user1> fallback Reverting to previous software image. Please confirm (y/n): [n] y FCSM: user1> admin end FCSM: user1>

Help command

Displays a brief description of the specified command and its keywords.

Authority

User

Syntax

help

[command] [keyword]

Keywords

[command]

A command name. If you omit this value, all available commands from which to choose are displayed.

[keyword]

A keyword associated with the command named by [command]. If you omit this value, available keywords for the specified command are displayed.

all

Displays a list of all available commands (including command variations).

Examples

The following is an example of the Help Set command.

FCSM: user1> help set

set SET_OPTIONS There are many attributes that can be set. Type help with one of the following to get more information: set alarm set beacon set blade set config blade set config port set config ports set config switch set config threshold set config zoning set log set pagebreak set port set setup snmp set setup system set switch

The following is an example of the Help Set Beacon command.

FCSM: user1> help set beacon set beacon On | Off This command allows the lights on the front of the switch to flash. The On option will start and the Off option will stop the flashing.

14 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

History command

Displays a numbered list of the previously entered commands from which you can re-execute selected commands.

Authority

User

Syntax

history

Notes

Use the History command to provide context for the! command.

• Enter ![command] to re-enter the most recent execution of that command.

• Enter ![line number] to re-execute the corresponding command from the History display

• Enter ![partial command string] to re-execute a command that matches the command string.

• Enter !! to re-execute the most recent command.

Examples

The following is an example of the History command.

FCSM: user1> history 1 show switch 2 date 3 help set 4 history

FCSM: user1> !2 date

Thu Sep 26 11:03:07 2002

Image command

Manages and installs switch firmware.

Authority

Admin

Syntax

image

cleanup fetch [account_name] [ip_address] [file_source] [file_destination] list unpack [file]

Keywords

cleanup

Removes all firmware image files from the switch. All firmware image files are removed automatically each time the switch is reset.

fetch [account_name] [ip_address] [file_source] [file_destination]

Retrieves image file given by [file_source] and stores it on the switch with the file name given by [file_destination]. The image file is retrieved from the device with the IP address given by [Ip_address] and an account name given by [account_name]. If an account name needs a password to access the device, you are prompted for it.

list

Displays the list of image files that reside on the switch.

unpack [file]

Installs the firmware file given by [file]. After unpacking the file, a message appears confirming successful unpacking. The switch must be reset for the new firmware to take effect.

16 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Lip command (for external ports only)

Reinitializes the specified loop port.

Authority

Admin

Syntax

lip

[port_number]

Keywords

[port_number]

The number of the port to be reinitialized.

Examples

The following is an example of the Lip command.

FCSM (admin) : user1> lip 2

Passwd command

Changes the password for a user account.

Authority

Admin to change the password for another account; user to change your own.

Syntax

passwd

[account_name]

Keywords

[account_name]

The user account name. You must open an admin session to change the password for an account name other than your own. If you omit [account_name], you are prompted to change the password for the current account name.

Examples

The following is an example of the Passwd command.

FCSM (admin) : user1> passwd user2

Press 'q' and the ENTER key to abort this command.

account OLD password : account NEW password (4-20 chars) :

please confirm account NEW password:

password has been changed.

✏ NOTE

If you lose the password for the account, contact Support (see A, “Getting help and technical assistance,” on page 155).

18 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Ps command

Displays current blade server process information.

Authority

User

Syntax

Examples

The following is an example of the Ps command.

FCSM: user1> ps PID PPID %CPU TIME ELAPSED COMMAND 341 329 0.0 00:00:00 2-00:58:29 cns 342 329 0.0 00:00:02 2-00:58:29 ens 343 329 0.0 00:00:27 2-00:58:29 dlog 344 329 1.3 00:40:39 2-00:58:29 ds 345 329 1.4 00:41:38 2-00:58:29 mgmtApp 346 329 0.0 00:00:06 2-00:58:29 fc2 347 329 0.5 00:16:35 2-00:58:29 nserver 348 329 0.4 00:12:20 2-00:58:29 mserver 349 329 3.6 01:47:29 2-00:58:29 util 350 329 0.0 00:00:36 2-00:58:29 snmpservicepath 351 329 0.5 00:15:24 2-00:58:29 eport 352 329 0.0 00:00:05 2-00:58:29 PortApp 361 329 0.0 00:00:08 2-00:58:28 port_mon 362 329 0.2 00:07:14 2-00:58:28 zoning 363 329 0.0 00:00:00 2-00:58:28 diagApp 385 329 0.0 00:00:02 2-00:58:18 snmpd 386 329 0.0 00:00:00 2-00:58:18 snmpmain

Quit command

Closes the Telnet session.

Authority

User

Syntax

quit, exit, or logout

Reset command

Resets the switch and port configuration parameters.

Authority

Admin

Syntax

reset

config [config_name] factory port [port_number] snmp switch (default) system zoning

Keywords

config [config_name]

factory

port [port_number]

snmp

switch

system

zoning

Resets the configuration given by [config_name] to the factory default values for switch, port, alarm threshold, and zoning configuration. This keyword clears all zoning definitions. If [config_name] does not exist on the switch, a configuration with that name is created. If you omit [config_name], the active conf iguration is reset. You must activate the configuration or reset the switch for the changes to take effect. See Table 2 on page 21 through Table 4 on page 22.

Resets switch, alarm threshold, port, SNMP, zoning configuration, and blade server configuration settings to the factory default values. The switch configuration is activated automatically. See Table 2 on page 21 through Table 6 on page 23.

Reinitializes the port given by [port_number]. Ports are numbered beginning with 0. For more information, see Table 37 on page 124.

Resets the SNMP configuration settings to the factory default values. See Table 5 on page 23 for SNMP configuration default values.

Reinitializes the switch. This is the default. This command also closes the Telnet session.

Resets the blade server configuration settings to the factory default values. See Table 6 on page 23 for configuration default values.

Clears the zoning database and deactivates the active zone set. The zoning configuration values remain unchanged.

20 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Notes

The following tables specify the various factory default settings.

Table 2. Switch conf iguration defaults

Parameter Default

Admin State Online Broadcast Enabled True Inband Enable True Domain ID 1 Domain ID Lock False Symbolic Name Fibre Channel Switch Module R_T_TO V 100 R_A_TOV 10000 E_D_TOV 2000 FS_TOV 5000 DS_TOV 5000 Principal Priority 254 System Description Fibre Channel Switch Module Configuration Last Saved By Initial Configuration Last Saved On Initial

Table 3. Port configuration defaults

Parameter External port (0,15) default Internal port (1-14) default

Admin State Online Online Link Speed Auto 2 Gbps Port Type GL F TL_Port Mode TLTargetMode TLTargetMode ISL Security Any Any Symbolic Name Port0 or Port15 Port1 – Port14 ALFairness False False ARB_FF False False InteropCredit 0 0 ExtCredit 0 0 FanEnable True True LCFEnable False False MFSEnable True True

Table 3. Port configuration defaults (continued)

Parameter External port (0,15) default Internal port (1-14) default

MFS_TOV 10 10 MSEnable True True NoClose False False IOStreamGuard False False VIEnable False False CheckAlps False False

Table 4. Threshol d configuration defaults

Parameter Default

ThresholdMonitoringEnabled True CRCErrorsMonitoringEnabled

RisingTrigger FallingTrigger SampleWindow

DecodeErrorsMonitoringEnabled RisingTrigger FallingTrigger SampleWindow

ISLMonitoringEnabled RisingTrigger FallingTrigger SampleWindow

LoginMonitoringEnabled RisingTrigger FallingTrigger SampleWindow

LogoutMonitoringEnabled RisingTrigger FallingTrigger SampleWindow

LOSMonitoringEnabled RisingTrigger FallingTrigger SampleWindow

True 25 1 10

True 200 0 10

True 2 0 10

True 5 1 10

True 100 5 10

22 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Table 5. SNMP configuration defaults

Parameter Default

Contact Undefined Location Undefined Description Undefined Trap [1] Address 10.0.0.1 Trap [2-5] Address 0.0.0.0 Trap [1-5] Port 162 Trap [1-5] Severity Warning Trap [1-5] Enabled False ObjectID 1.3.6.1.4.1.1663.1.1.1.1.16 AuthFailureTrap False

Table 6. System configuration defaults

Parameter Default

Ethernet Network IP Address Switch module bay 3: 192.168.70.129

Switch module bay 4: 192.168.70.130 Ethernet Network IP Mask 255.255.255.0 Ethernet Gateway Address 10.90.90.254 Ethernet Network Discovery Static Admin Timeout 30 minutes Security Enabled False Local Log Enabled True Remote Log Enabled False Remote Log Host IP Address 10.0.0.254

Set command

Sets a variety of port and switch parameters.

Authority

Admin for all keywords except Alarm Clear, Beacon, and Pagebreak which are available with User authority.

Syntax

set

alarm clear beacon [state] config [option] log [option] pagebreak [state] port [option] setup [option] switch [state]

Keywords

alarm clear

Clears the alarm log. This keyword is available with User authority.

beacon [state]

Enables or disables the flashing of the Port Logged-in LEDs according to [state]. This keyword is available with User authority. [state] can be one of the following:

Enables the flashing beacon.

Off

Disables the flashing beacon.

config [option]

Sets port, switch, alarm threshold, and zoning configuration parameters. See the “Set Config command” on page 26.

log [option]

Specifies the type of entries to be entered in the event log. See the “Set Log command” on page 32.

pagebreak [state]

Specifies how much information is displayed on the screen at a time according to the value given by [state]. This keyword is available with User authority. [state] can be one of the following:

Limits the display of information to 20 lines at a time.

Off

Allows continuous display of information without a break.

port [option]

Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. See the “Set Port command” on page 34.

setup [option]

Changes SNMP and blade server configuration settings. See the “Set Setup command” on page 35.

24 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

switch [state]

Temporarily changes the administrative state for all ports on the switch to the state given by [state]. The previous Set Config Switch settings are restored after a switch reset or a reactivation of a switch configuration. [state] can be one of the following:

Online

Offline

Diagnostics

Places all ports online

Places all ports offline.

Prepares all ports for testing.

Set Config command

Sets port, switch, alarm threshold, and zoning configuration parameters.

Authority

Admin authority and a Config Edit session. See the “Config command” on page 10 for information about starting a Config Edit session.

Syntax

set config

port [port_number] ports [port_number] switch threshold zoning

Keywords

port [port number]

Initiates an editing session in which to change configuration parameters for the port number given by [port_number]. If you omit [port_number], the Blade Server Chassis SBCE begins with port 0 and proceeds in order through port 15. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Type q to cancel the configuration for one port, or qq to cancel the configuration for all ports. Table 7 on page 26 describes the port parameters.

✏ NOTE

For external ports (0,15), all port parameters apply. For internal ports, only the port state setting is configurable. For information about port numbering and mapping, see Table 37 on page 124.

port [port number]

✏ NOTE

For external ports (0,15), all port parameters apply. For internal ports, only the port state setting is configurable. For information about port numbering and mapping, see Table 37 on page 124.

ports [port number]

Initiates an editing session in which to change configuration parameters for all ports based on the configuration for the port giv en by [port_number]. If you omit [port_number], port 0 is used. F or each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. Type q to cancel the configuration. Table 7 on page 26 describes the port parameters. For external ports (0,15), all parameters apply. For internal ports (1 through 14) only AdminState applies.

Table 7. Set Config port parameters

Parameter Description

AdminState Port administrative state: online, offline, diagnostics, or down. LinkSpeed 1 Gbps or 2 Gbps. PortType Type of port.

26 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Table 7. Set Config port parameters (continued)

Parameter Description

TLPortMode Initiates the configuration of external ports attributes. Indicates whether using

initiator or target devices on the loop. If you specify [port_number], the display will present attributes for that port only; otherwise, all attributes for all ports will be available for configuration.

ISLSecurity E_Port security. Determines which switches a port will establish a link with.

• Any - Will link with any switch.

• Ours - Will link only to another Fibre Channel switch module.

• None - The port will not establish an ISL link. SymbolicPortName Descriptive name. ALFairness Default is switch that has priority. ARB_FF Use ARB_FF instead of idles on loop FCAL option. InteropCredit Number of buffer-to-buffer credits per port. 0 means the default (12) is

unchanged. ExtCredit Extended credit port. FANEnable Fabric Address Notification. If enabled, notifies logged-in NL_Ports of the

FL_Port address, port name, and node name. LCFEnable Link control frame preference, R_CTL = 0xC. MFSEnable Multi-frame sequence bundling. MFS_TOV MFS limit for camp on. MSEnable Management Server enable on this port. NoClose Do not close unless another device arbitrates. I/O Stream Guard Enables or disables the suppression of RSCN messages. IVIEnable Not applicable. CheckAlps Close befo re sending frames to new target.

switch

Initiates an editing session in which to change switch configuration settings. Each parameter is displayed, one line at a time and prompts you for a value. For each parameter, type a new value or press the Enter key to accept the current value shown in brackets. Type q to cancel the conf iguration.

Table 8. Set Config switch parameters

Parameter Description

AdminState Switch administrative state: online, offline, or diagnostics. Broadcast Enable Enables (True) or disables (False) forwarding if broadcasting frames. InbandEnabled Enables (True) or disables (False) the ability to manage the switch over an

ISL.

DefaultDomainID Default domain ID setting.

DomainIDLock Prevents (True) or allows (False) dynamic reassignment of the domain ID.

Table 8. Set Config switch parameters (continued)

Parameter Description

SymbolicName Descriptive name. R_T_TOV Receiver Transmitter Timeout Value. Specifies the n umbe r of mi llise co nds a

port is to wait to receive a response from another port. The default is 100.

R_A_TOV Resource Allocation Timeout Value. The number of milliseconds the switch

waits to allow two ports to allocate enough resources to establish a link. The default is 10000.

E_D_TOV Error Detect Timeout Value. The number of milliseconds a port is to wait for

errors to clear. The default is 2000 msec. FS_TOV Fabric Stability Timeout Value. The default is 5000 msec. DS_TOV Distributed Services Timeout Value (Management Server, Name Server).

The default is 5000 msec. PrincipalPriority The priority used in the FC-SW-2 principal switch selection algorithm. 1 is

high, 255 is low. ConfigDescription The name for the configuration. The default is undefined.

threshold

Initiates a configuration session by which to generate and log alarms for selected events. Each event, its thresholds, and sampling interval is displayed, one line at a time and you are prompted for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets. These parameters must be saved in a configuration and activated before they will tak e effect. See the “Config command” on page 10 for information about saving and activating a configuration. Table 9 describes the Set Config threshold parameters.

Table 9. Set Config threshold parameters

Parameter Description

Threshold Monitoring Enabled Master enable/disable parameter for all events. Enables (True) or

disables (False) the generation of all enabled event alarms.

CRCErrorsMonitoringEnabled DecodeErrorsMonitoringEnabled ISLMonitoringEnabled LoginMonitoringEnabled LogoutMonitoringEnabled LOSMonitoringEnabled

Rising Trigger The event count above which an event is logged. Once the count

Falling Trigger The event count above which an event becomes eligible for logging in

Sample Window The period of time in seconds in which to count events.

The event type enable/disable parameter. Enables (True) or disables (False) the generation of alarms for each of the following events:

• CRC errors

• Decode errors

• ISL connection count

• Login errors

• Logout errors

• Loss-of-signal errors

exceeds the rising threshold, one alarm is logged. The switch will not generate another alarm for that event until the count falls below the falling threshold and rises again above the rising threshold.

the alarm log.

28 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

zoning

Initiates an editing session in which to change switch zoning attributes. Each parameter is displayed, one line at a time, and you are prompted for a value. For each parameter, enter a new value or press the Enter key to accept the current value shown in brackets.

Table 10. Set Config zoning parameters

Parameter Description

AutoSave Determines whether zoning changes will be saved to flash (nonvolatile) memory (On)

or to RAM (volatile) (Off). The default is On.

Default Determines communication among ports/devices in the absence of an active zone set.

“All” enables all ports/devices to communicate with one another. “None” prohibits communication among ports/devices.

Examples

The following is an example of the Set Config Port command.

FCSM: user1> admin start FCSM (admin) : user1> config edit FCSM (admin-config) : user1> set config port 0

A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.

Configuring Port Number: 0

----------------------- AdminState (1=Online, 2=Offline, 3=Diagnostics, 4=Down) [Online ] LinkSpeed (1=1Gb/s, 2=2Gb/s, 3=Auto) [Auto ] PortType (TL / GL / G / F / FL / Donor) [GL ] TLPortMode (1=TLTargetMode, 2=TLInitiatorMode) [TLTargetMode] ISLSecurity (Any / Ours / None) [Any ] SymPortName (string, max=32 chars) [Port0 ] ALFairness (True / False) [False ] ARB_FF (True / False) [False ] InteropCredit (decimal value, 0-255) [0 ] ExtCredit (dec value, increments of 11, non-loop only) [0 ] FANEnable (True / False) [True ] LCFEnable (True / False) [False ] MFSEnable (True / False) [True ] MFS_TOV (decimal value, 10-20480 msec) [10 ] MSEnable (True / False) [True ] NoClose (True / False) [False ] IOStreamGuard (Enable / Disable) [Disabled ] VIEnable (True / False) [False ] CheckAlps (True / False) [False ]

Finished configuring attributes. This configuration must be saved (see config save command) and activated (see config activate command) before it can take effect. To discard this configuration use the config cancel command.

The following is an example of the Set Config Switch command.

FCSM: user1> admin start FCSM (admin) : user1> config edit FCSM (admin-config) : user1> set config switch

AdminState (1=Online, 2=Offline, 3=Diagnostics) [Online] BroadcastEnabled (True / False) [True] InbandEnabled (True / False) [True] DefaultDomainID (decimal value, 1-239) [1] DomainIDLock (True / False) [False] SymbolicName (string,max=32 chars) [Fibre Channel Switch Module] R_T_TOV (decimal value, 1-1000 msec) [100] R_A_TOV (decimal value, 100-100000 msec) [10000] E_D_TOV (decimal value, 10-20000 msec) [2000] FS_TOV (decimal value, 100-100000 msec) [5000] DS_TOV (decimal value, 100-100000 msec) [5000] PrincipalPriority (decimal value, 1-255) [254] ConfigDescription (string, max=64 chars) [ Fibre Channel Switch Module] Finished configuring attributes. This configuration must be saved (see config save command) and activated (see config activate command) before it can take effect. To discard this configuration use the config cancel command.

The following is an example of the Set Config Threshold command.

FCSM (admin-config) : user1> set config threshold A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so. ThresholdMonitoringEnabled (True / False) [False]

CRCErrorsMonitoringEnabled (True / False) [False] RisingTrigger (decimal value, 1-1000) [25 ] FallingTrigger (decimal value, 0-1000) [1 ] SampleWindow (decimal value, 1-1000 sec) [10 ]

30 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

DecodeErrorsMonitoringEnabled (True / False) [True ] RisingTrigger (decimal value, 1-1000) [200 ] FallingTrigger (decimal value, 0-1000) [0 ] SampleWindow (decimal value, 1-1000 sec) [10 ]

ISLMonitoringEnabled (True / False) [True ] RisingTrigger (decimal value, 1-1000) [2 ] FallingTrigger (decimal value, 0-1000) [0 ] SampleWindow (decimal value, 1-1000 sec) [10 ]

LoginMonitoringEnabled (True / False) [True ] RisingTrigger (decimal value, 1-1000) [5 ] FallingTrigger (decimal value, 0-1000) [1 ] SampleWindow (decimal value, 1-1000 sec) [10 ]

LogoutMonitoringEnabled (True / False) [True ] RisingTrigger (decimal value, 1-1000) [5 ] FallingTrigger (decimal value, 0-1000) [1 ] SampleWindow (decimal value, 1-1000 sec) [10 ]

LOSMonitoringEnabled (True / False) [True ] RisingTrigger (decimal value, 1-1000) [100 ] FallingTrigger (decimal value, 0-1000) [5 ] SampleWindow (decimal value, 1-1000 sec) [10 ]

The following is an example of the Set Config Zoning command.

FCSM: user1> admin start FCSM (admin) : user1> config edit FCSM (admin-config) : user1> set config zoning

AutoSave (True / False) [True] Default (All / None) [All ]

Set Log command

Specifies the type of entries to be entered in the event log. The log is a storage file contained on the switch. The log can hold a maximum of 200 entries. When the log becomes full, the entries are replaced, starting with the oldest entry, to produce a list of the last 200 events which occurred. Log entries are created for ports, components, and event severity levels.

Authority

Admin

Syntax

set log

archive clear component [list] level [level] port [port_list] restore save start (default) stop

Keywords

archive

clear

component [list]

Archives the log entries to a file on the switch named logfile that can be do wnloaded from the switch using FTP. To download the log file, open an FTP session, log in with an account name of images and password of images, and type get logfile.

Clears all log entries.

Specifies one or more components to monitor for events. Use spaces to delimit values in the list. Use one or more of the following values:

All

Monitors all components. To maintain optimal switch performance, do not use this setting with the Level keyword set to Info.

Blade

Not applicable

Chassis

Not applicable

Eport

Monitors all E_Ports.

Mgmtserver

Monitors management server status.

Nameserver

Monitors name server status.

None

Monitors none of the component events.

Other

Monitors other miscellaneous events.

32 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Port

Monitors all port events.

Switch

Monitors switch management events.

Zoning

Monitors zoning conflict events.

level [level]

Specifies the severity level given by [level] to use in monitoring events for the specified components or ports. [level] can be one of the following values:

Critical

Monitors critical events.

Warn

Monitors warning events.

Info

Monitors informational events. To maintain optimal switch performance, do not use this setting with the Component keyword set to All.

None

Monitors none of the severity levels.

port [port_list]

Specifies one or more ports to monitor for events. Use one of the follo wing values:

[port_list]

Specifies port or ports to monitor. Use spaces to delimit values in the list. Ports are numbered beginning with 0.

All

Specifies all ports.

None

Disables monitoring on all ports.

restore

Returns the port, component, and level settings to the default values.

save

Saves the log settings for the component, level, and port. These settings remain in effect after a switch reset. The log settings can be viewed using the Show Log Settings command. To export log entries to a file, use the Set Log Archive command.

start

Starts the logging of events based on the Port, Component, and Level keywords assigned to the current configuration. The logging continues until you enter the Set Log Stop command.

stop

Stops logging of events.

Notes

To maintain optimal switch performance, do not set the Component keyword to All and the Level keyword to Info at the same time.

Set Port command

Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. For information about port numbering and mapping, see Table 37 on page 124.

✏ NOTE

For external ports (0,15), all port parameters apply. For internal ports, only the port state setting is configurable.

Authority

Admin

Syntax

set port [port_number]

• bypass [alpa] (for external ports only)

• clear

• enable [alpa] (for external ports only)

• speed [transmission_speed]

• state [state]

Keywords

[port_number]

Specifies the port. Ports are numbered beginning with 0. For information about port numbering and mapping, see Table 37 on page 124.

bypass [alpa]

Sends a Loop Port Bypass (LPB) to a specific Arbitrated Loop Physical Address (ALPA) or to all ALPAs on the arbitrated loop. [alpa] can be a specific ALPA or the keyword ALL to choose all ALPAs.

clear

Clears the counters on the specified port.

enable [alpa]

Sends a Loop Port Enable (LPE) to all ALPAs on the arbitrated loop. [alpa] can be a specific ALPA or the keyword ALL to choose all ALPAs.

speed [transmission_speed]

Specifies the transmission speed for the specified port. Use one of the following port speed values:

1Gbps

2Gbps

Auto

state [state]

Specifies the administrative state for the specified port. Use one of the following port state values:

Online

Offline

Diagnostics

Down

One gigabit per second.

Two gigabits per second.

The port speed is automatically detected.

Places the port online.

Places the port offline.

Prepares the port for testing.

Disables the port.

34 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Set Setup command

Changes SNMP and blade server configuration settings. The switch maintains one SNMP configuration and one configuration.

Authority

Admin

Syntax

set setup

snmp system

Keywords

snmp

Prompts you, line-by-line, to change SNMP configuration settings. Table 11 describes the SNMP fields. For each parameter, enter a new value or pr ess the Enter k ey to accept the current value shown in brackets.

Table 11. SNMP configuration settings

Entry Description

Contact Specifies the name of the person to be contacted to respond to trap events.

The default is Undefined. Location Specifies the name of the switch location. The default is Undefined. Trap [1-5] Address Specifies the IP address to which SNMP traps are sent. Trap [1-5] Po rt Specifies the port for which SNMP traps are sent. Trap [1-5] Severity Specifies the severity level to use when monitoring trap events. The default is

Warning. Trap [1-5] Enabled Specifies whether traps (event information) are enabled or disabled (default). ReadCommunity Read Community Authentication. A write-only field; the value on the switch

and the SNMP management server must be the same. WriteCommunity Write Community Authentication. A write-only field; the value on the switch

and the SNMP management server must be the same. TrapCommunity Trap Community Authentication. A write-only field; the value on the switch and

the SNMP management server must be the same. AuthFailureTrap Specifies the IP address where a notification is sent in the event of an

authentication failure.

system

Prompts you, line-by-line, to change blade server configuration settings. Table 12 describes the system configuration fields. For each parameter , enter a ne w value or press the Enter key to accept the current value shown in brackets.

Table 12. System conf iguration settings

Entry Description

Eth0NetworkAddress Ethernet Internet protocol (IP) address Eth0NetworkMask Ethernet subnet mask address for the Ethernet port. Eth0GatewayIPAddress Ethernet IP address gateway Eth0NetworkDiscovery Ethernet boot method (1 - Static).

AdminTimeout Specifies the amount of time in minutes the switch waits bef ore terminating an

Security Enabled Enables or disables the enforcement of account names and passwords. Remote Log Enabled Whether remote logging is enabled or disabled. If enabled, log information is

RemoteLogHost IP Address The IP address of the host that will receive the remote log information if

Note: BootP, DHCP, and RARP do not apply

idle Admin session. Zero (0) disables the time out threshold. The default is 30;

the maximum is 1440.

saved to a remote host that supports the systole protocol.

remote logging is enabled.

Notes

The two components of security are user authentication and fabric security. The user must be authenticated before gaining access to a switch. If an invalid account name/password combination is entered, that user can not access the switch, and thus cannot gain access to the fabric. If security is enabled (True) and a valid account name/password combination is entered, that user can access the switch but can not execute any command that exceeds their authority (privileges) level. If security is disabled (False) and a valid account name/password combination is entered, that user has access to all switches in the fabric and can execute all commands (both user and admin), regardless of their authority (privileges) level.

Examples

The following is an example of the Set Setup SNMP command.

FCSM: user1> admin start FCSM (admin) : user1> set setup snmp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.

Trap Severity Options

-------------------- unknown, emergency, alert, critical, error, warning, notify, info, debug, mark

Contact (string, max=32 chars) [<sysContact undefined> ] Location (string, max=32 chars) [<sysLocation undefined>]

Trap1Address (dot-notated IP Address) [10.0.0.1 ]

36 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Trap1Port (decimal value) [162 ] Trap1Severity (see allowed options above) [warning ] Trap1Enabled (True / False) [False ] Trap2Address (dot-notated IP Address) [0.0.0.0 ] Trap2Port (decimal value) [162 ] Trap2Severity (see allowed options above) [warning ] Trap2Enabled (True / False) [False ] Trap3Address (dot-notated IP Address) [0.0.0.0 ] Trap3Port (decimal value) [162 ] Trap3Severity (see allowed options above) [warning ] Trap3Enabled (True / False) [False ] Trap4Address (dot-notated IP Address) [0.0.0.0 ] Trap4Port (decimal value) [162 ] Trap4Severity (see allowed options above) [warning ] Trap4Enabled (True / False) [False ] Trap5Address (dot-notated IP Address) [0.0.0.0 ] Trap5Port (decimal value) [162 ] Trap5Severity (see allowed options above) [warning ] Trap5Enabled (True / False) [False ] ReadCommunity (string, max=32 chars) [public ] WriteCommunity (string, max=32 chars) [private ] TrapCommunity (string, max=32 chars) [public ] AuthFailureTrap (True / False) [False ]

Do you want to save and activate this snmp setup? (y/n): [n]

The following is an example of the Set Setup System command.

FCSM: user1> admin start FCSM (admin) : user1> set setup system

Eth0NetworkAddress (dot-notated IP Address) [10.90.10.93 ] Eth0NetworkMask (dot-notated IP Address) [255.255.252.0] Eth0GatewayAddress (dot-notated IP Address) [10.20.8.254 ] Eth0NetworkDiscovery (1=Static, 2=Bootp, 3=Dhcp, 4=Rarp) [Static ] AdminTimeout (dec value 0-1440 minutes, 0=never) [30 ] SecurityEnabled (True / False) [False ] LocalLogEnabled (True / False) [True ] RemoteLogEnabled (True / False) [False ] RemoteLogHostAddress (dot-notated IP Address) [10.0.0.254 ]

Do you want to save and activate this system setup? (y/n): [n]

Show command

Displays fabric, switch, and port operational information.

Authority

User

Syntax

show

about alarm broadcast chassis config [option] domains donor fabric interface log [option] lsdb mem [count] ns [option] pagebreak perf [option] port [port_number] post log setup [option] steering [domain_id] support switch topology users version

Keywords

about

Displays an introductory set of information about operational attributes of the switch. This keyword is equivalent to the Version keyword.

alarm

Displays the last 200 alarm entries.

broadcast

Displays the broadcast tree information and all ports that are currently transmitting and receiving broadcast frames.

chassis

Not applicable

config [option]

Displays switch and port configuration attributes. For more information, see the “Show Config command” on page 45.

38 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

domains

Displays a list of each domain and its worldwide name in the fabric.

donor

Displays list of current donor configuration for all ports.

fabric

Displays list of each domain, fabric ID, worldwide name, node IP address, port IP address, and symbolic name in the fabric.

interface

Displays the status of the active network interfaces.

log [option]

Displays log entries. See the “Show Log command” on page 48.

lsdb

Displays Link State database information.

mem [count]

Displays information about memory activity for the number of seconds given by [count]. If you omit [count], the value 1 is used. Displayed memory values are in units of 1 KB.

✏ NOTE

This keyword will display memory activity updates until [count] is reached; it cannot be interrupted. Therefore, avoid using large values for [count].

ns [option]

Displays name server information for the specified [option]. If you omit [option], name server information for the local domain ID is displayed. [option] can have the following values:

all

Displays name server information for all switches and ports.

[domain_id]

Displays name server information for the switch given by [domain_id]. [domain_id] is a switch domain ID.

[port_id]

Displays name server information for the port given by [port_id]. [port_id] is a port Fibre Channel address.

pagebreak

Displays the current pagebreak setting. The pagebreak setting limits the display of information to 20 lines (On) or allows the continuous display of information without a break (Off).

perf [option]

Displays performance information for all ports. See the “Show Perf command” on page 50.

port [port_number]

Displays operational information for the port given by [port_number]. Ports are numbered beginning with 0. If the port number is omitted, information is displayed for all ports. Table 13 on page 40 describes the port parameters. For information about port numbering and mapping, see Table 37 on page 124.

✏ NOTE

For external ports (0,15), all parameters apply. For internal ports (1 through 14) only AdminState applies.

Table 13. Show Port parameters

Entry Description

AIinit Incremented each time the port begins AL initialization. AIinitError Number of times the port entered initialization and the initialization failed. ClassXFramesIn Number of class x frames received by this port. ClassXFramesOut Number of class x frames sent by this port. ClassXWordsIn Number of class x words received by this port. ClassXWordsOut Number of class x words sent by this por t. DecodeError Decoding error detected. EpConnects Number of times an E_Port connects through ISL negotiation. FBusy Number of times the switch sent a F_BSY because Class 2 frame could not be

delivered within ED_TOV time. Number of class 2 and class 3 fabric busy (F_BSY) frames generated by this port in response to incoming frames. This usually indicates a busy condition on the fabric or N_port that is preventing delivery of this

frame. Flowerrors Received a frame when there were no available credits. FReject Number of frames from devices that were rejected. InvalidCRC Invalid CRC detected. InvalidDestAddr Invalid destination address detected. LIP ALPD ALPS Number of F7, AL_PS LIPs, or AL_PD (vendor specific) resets, performed. LIPF7ALPS This LIP is used to reinitialize the loop. An L_port, identified by AL_PS, may have

noticed a performance degradation and is trying to restore the loop. LIPF8ALPS This LIP denotes a loop failure detected by the L_port identified by AL_PS. LIPF7F7 A loop initialization primitive frame used to acquire a valid AL_PA. LIPF8F7 A loop initialization primitive frame used to indicate that a loop failure has been

detected at the receiver. Link Failures Number of optical link failures detected by this port. A link failure is a loss of

synchronization for a period of time greater than the value of R_T_TOV or by loss of

signal while not in the offline state. A loss of signal causes the switch to attempt to

re-establish the link. If the link is not re-established by the time specified by

R_T_TOV, a link failure is counted. A link reset is performed after a link failure. Login Time when user logged in. Logout Time when user logged out. LoopTimeouts A 2-second timeout as specified by FC-AL-2. LossOfSync Number of synchronization losses (>100 ms) detected by this port. A loss of

synchronization is detected by receipt of an invalid transmission word. PrimSeqErrors Primitive sequence errors detected. RxLinkResets Number of link reset primitives received from an attached device. RxOfflineSeq Number of offline sequences received. An OLS is issued for link initialization, a

Receive & Recognize Not_Operational (NOS) state, or to enter the offline state.

40 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Table 13. Show Port parameters (continued)

Entry Description

TotalErrors Total number of errors detected. TotalLIPsRecvd Number of loop initialization primitive frames received by this port. TotalLinkResets Total number of link reset primitives. TotalOfflineSeq Total number of Offline Sequences issued by this port. TotalRxFrames Total number of frames received by this port. TotalRxWords Total number of words received by this port. TotalTxFrames Total number of frames issued by this port. TotalTxWords Total number of words issued by this port. TxLinkResets Number of Link Resets issued by this port. TxOfflineSeq Total number of Offline Sequences issued by this port. TxWait Time waiting to transmit when blocked with no credit. Measured in FC Word times.

post log

Displays the POST log which contains results from the POST.

setup [option]

Displays setup attributes for the system, SNMP, and the switch manufacturer. See the “Show Setup command” on page 52.

steering [domain_id]

Displays the routes that data takes to the switch g iven by [domain_id]. If you omit [domain_id], the system displays routes for all switches in the fabric.

support

Executes a series of commands that display a complete description of the switch, its configuration, and operation. The display can be captured from the screen and used for diagnosing problems. This keyword is intended for use at the request of your authorized maintenance pro vider. The following commands are executed:

•Date

• Alias List

• Config List

•Date

• History

•Ps

• Show (About, Alarm, Backtrace, Chassis, Config Port, Config Switch, Dev, Dev Settings, Domains, Donor, Fabric, Log, Log Settings, Lsdb, Mem, Ns, Perf, Port, Setup Mfg, Setup Snmp, Setup System, Steering, Switch, Topology, Users)

• Uptime

• User Accounts

• Whoami

• Zoneset (Active, List)

• Zoning (History, Limits, List)

switch

Displays switch operational information.

topology

Displays all connected devices.

users

Displays a list of logged-in users. This is equivalent to the User List command.

version

Displays an introductory set of information about operational attributes of the switch. This keyword is equivalent to the About keyword.

Examples

The following is an example of the Show Setup SNMP command.

FCSM: user1> show setup snmp

SNMP Information

--------------- Contact <sysContact undefined> Location <sysLocation undefined> Description Fibre Channel Switch Module Trap1Address 10.0.0.1 Trap1Port 162 Trap1Severity warning Trap1Enabled False Trap2Address 0.0.0.0 Trap2Port 162 Trap2Severity warning Trap2Enabled False Trap3Address 0.0.0.0 Trap3Port 162 Trap3Severity warning Trap3Enabled False Trap4Address 0.0.0.0 Trap4Port 162 Trap4Severity warning Trap4Enabled False Trap5Address 0.0.0.0 Trap5Port 162 Trap5Severity warning Trap5Enabled False ObjectID 1.3.6.1.4.1.1663.1.1.1.1.16 AuthFailureTrap False

42 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

The following is an example of the Show Topology command.

FCSM: user1> show topology Unique ID Key

------------ A = ALPA, D = Domain ID, P = Port ID

Loc Local Rem Remote Unique Port Type PortWWN Type NodeWWN ID

---- ---- ------- ---- ------- ----- Ext:15 E 20:0f:00:c0:dd:00:90:fb E 10:00:00:c0:dd:00:90:d74 (0x4) D

The following is an example of the Show Topology (for Port #15) command.

FCSM: user1> show topology 15 Local Link Information

--------------------- Port Ext2:15 PortID 020f00 PortWWN 20:0f:00:c0:dd:00:90:fb PortType E

Remote Link Information

---------------------- Remote Switch PortNumber 10 DomainID 04 NodeWWN 10:00:00:c0:dd:00:90:d7 PortType E Description Switch IPAddress 10.0.0.3

The following is an example of the Show Port command.

FCSM: user1> show port 0 Port Number: 0

----------- AdminState Online PortID 640000 AsicNumber 0 PortWWN 20:00:00:c0:dd:00:91:03 AsicPort 0 RunningType E ConfigType GL SFPPartNumber FTRJ-8519-3-2.5 DiagStatus Passed SFPRevision X1 EpConnState Connected SFPType 100-M5-SN-I EpIsoReason NotApplicable SFPVendor FINISAR CORP. LinkSpeed 2Gb/s SFPVendorID 00659000 LinkState Active SymbolicName Port0 LoginStatus LoggedIn SyncStatus SyncAcquired MaxCredit 12 XmitterEnabled True

OperationalState Online ALInit 11 FlowErrors 0 PrimSeqErrors 0 ALInitError 1 FReject 0 RxLinkResets 0 Class2FramesIn 0 InvalidCRC 0 RxOfflineSeq 0 Class2FramesOut 0 InvalidDestAddr 0 TotalErrors 1 Class2WordsIn 0 LIP_AL_PD_AL_PS 0 TotalLIPsRecvd 15 Class2WordsOut 0 LIP_F7_AL_PS 0 TotalLinkResets 0 Class3FramesIn 0 LIP_F7_F7 15 TotalOfflineSeq 0 Class3FramesOut 0 LIP_F8_AL_PS 0 TotalRxFrames 0 Class3Toss 0 LIP_F8_F7 0 TotalRxWords 0 Class3WordsIn 0 LinkFailures 0 TotalTxFrames 0 Class3WordsOut 0 Login 7 TotalTxWords 0 DecodeErrors 0 Logout 6 TxLinkResets 0 EpConnects 7 LoopTimeouts 0 TxOfflineSeq 0 FBusy 0 LossOfSync 1 TxWaits 0

The following is an example of the Show Switch command.

FCSM: user1> show switch Switch Information

----------------- SymbolicName Fibre Channel Switch Module SwitchWWN 10:00:00:c0:dd:00:91:03 SwitchType SBXL52 PROMVersion V1.4.0.1-0 (Thu Sep 12 17:46:41 2002) CreditPool 0 DomainID 1 (0x1) FirstPortAddress 010000 FlashSize - MBytes 128 LogLevel Critical MaxPorts 16 NumberOfResets 14 ReasonForLastReset NormalReset SWImageVersion (1) - build date V1.4.0.18-3 (Thu Sep 19 03:55:16 2002) SWImageVersion (2) - build date V1.4.0.19-1 (Fri Sep 20 03:56:20 2002) ActiveConfiguration default ActiveSWImage 2 AdminState Online AdminModeActive False BeaconOnStatus False OperationalState Online PrincipalSwitchRole True BoardTemp (1) - Degrees Celsius 50 BoardTemp (2) - Degrees Celsius 50 SwitchDiagnosticsStatus Passed SwitchTemperatureStatus Normal

44 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Show Config command

Display port, switch, alarm threshold, and zoning attributes for the current configuration.

Authority

User

Syntax

show config

port [port_number] switch threshold zoning

Keywords

port [port_number]

Displays configuration parameters for the port number given by [port_number]. Ports are numbered beginning with 0. If the port value is omitted, all ports are specified.

✏ NOTE

For external ports (0,15), all parameters apply. For internal ports (1 through 14) only AdminState applies. For information about port numbering and mapping, see Table 37 on page 124.

switch

Displays configuration parameters for the switch.

threshold

Displays alarm threshold parameters for the switch.

zoning

Displays zoning configuration parameters for the switch.

Examples

The following is an example of the Show Config Port command.

FCSM: user1> show config port 15 Configuration Name: lei

------------------ Port Number: 15

----------- AdminState Online LinkSpeed Auto PortType GL TLPortMode TLTargetMode ISLSecurity Any SymbolicName Port15 ALFairness False ARB_FF False InteropCredit 0 ExtCredit 0 FANEnable True LCFEnable False MFSEnable True

MFS_TOV 10 MSEnable True NoClose False IOStreamGuard Disabled VIEnable False CheckAlps False

The following is an example of the Show Config Switch command.

FCSM: user1> show config switch Configuration Name: lei

------------------ Switch Configuration Information

------------------------------- AdminState Online BroadcastEnabled True InbandEnabled True DomainID 1 (0x1) DomainIDLock False SymbolicName Fibre Channel Switch Module R_T_TOV 100 R_A_TOV 10000 E_D_TOV 2000 FS_TOV 5000 DS_TOV 5000 PrincipalPriority 254 ConfigDescription Fibre Channel Switch Module ConfigLastSavedBy Initial ConfigLastSavedOn Initial

The following is an example of the Show Config Threshold command.

FCSM: user1> show config threshold Configuration Name: default

------------------ Threshold Configuration Information

---------------------------------- ThresholdMonitoringEnabled True CRCErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 1 SampleWindow 10 DecodeErrorsMonitoringEnabled True RisingTrigger 200 FallingTrigger 0 SampleWindow 10

46 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

ISLMonitoringEnabled True RisingTrigger 2 FallingTrigger 0 SampleWindow 10 LoginMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LogoutMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LOSMonitoringEnabled True RisingTrigger 100 FallingTrigger 5 SampleWindow 10

The following is an example of the Show Config Zoning command.

FCSM: user1> show config zoning Configuration Name: default

------------------ Zoning Configuration Information

------------------------------- AutoSave True Default All

Show Log command

Displays the contents of the log or the parameters used to create entries in the log. The log contains a maximum of 200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest.

Authority

User

Syntax

show log

component level options port settings

Keywords

component

Displays the components currently being monitored for events.

level

Displays the event severity level needed to create an entry in the log. If the severity level occurs on a port or on a component which is not defined, no entry is made in the log.

options

Displays the options used to set the component and log level attributes.

port

Displays the ports being monitored for events. If an event occurs which is of the defined level and on a defined component, but not on a defined port, no entry is made in the log.

settings

Displays the current settings for component, level and port. This command is equivalent to executing the following commands separately: Show Log Component, Show Log Level, and Show Log Port.

Examples

The following is an example of the Show Log Component command.

FCSM: user1> show log component Current setting(s) for log component: NameServer

The following is an example of the Show Log Le vel command.

FCSM: user1> show log level Current settings for log

----------------------- level Critical

The following is an example of the Show Log Options command.

FCSM: user1> show log options

Allowed options for ' level': Critical,Warn,Info,None Allowed options for 'component':

All,None,NameServer,MgmtServer,Zoning,Switch,Chassis,Blade,Port,Eport,Snmp,Other

48 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Current setting(s) for log port: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

The following is an example of the Show Log command.

[327][Wed Jan 25 09:36:54.860 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][Eport State = E_A0_GET_DOMAIN_ID] [328][Wed Jan 25 09:36:54.860 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][ FSPF

PortUp state=0] [329][Wed Jan 25 09:36:54.861 1989][I][Eport:0xdd00b8b6.304.4 Port:

0/8][Sending init hello] [330][Wed Jan 25 09:36:54.861 1989][I][Eport:0xdd00b8b6.304.4 Port:

0/8][Processing EFP, oxid= 0x8] [331][Wed Jan 25 09:36:54.861 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][Eport

State = E_A2_IDLE] [332][Wed Jan 25 09:36:54.861 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][EFP,

WWN= 0x100000c0dd00b845, len= 0x30] [333][Wed Jan 25 09:36:54.864 1989][I][Eport:0xdd00b8b6.304.4 Port:

0/8][Sending LSU oxid= 0xc: type= 1] [334][Wed Jan 25 09:36:54.864 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][Send

Zone Merge Request] [335][Wed Jan 25 09:36:54.865 1989][I][Eport:0xdd00b8b6.304.4 Port: 0/8][LSDB

Xchg timer set] [336][Wed Jan 25 09:36:54.865 1989][I][Eport:0xdd00b8b6.304.4 Port:

0/8][Setting attribute Oper.UserPort.0.8.EpConnState Connected]

Show Perf command

Displays port performance in frames per second and bytes per second. If you omit the keyword, the command displays data transmitted (out), data received (in), and total data transmitted and received in frames per second and bytes per second.

Authority

User

Syntax

show perf

byte inbyte outbyte [port_number] frame [port_number] inframe [port_number] outframe [port_number] errors [port_number]

Keywords

byte

Displays continuous performance data in total bytes per second transmitted and received for all ports. Type q and press the Enter key to stop the display.

inbyte

Displays continuous performance data in bytes per second received for all ports. Type q and press the Enter key to stop the display.

outbyte [port_number]

Displays continuous performance data in bytes per second transmitted for all ports. Type q and press the Enter key to stop the display.

frame [port_number]

Displays continuous performance data in total frames per second transmitted and received for all ports. Type q and press the Enter key to stop the display.

inframe [port_number]

Displays continuous performance data in frames per second received for all ports. Type q and press the Enter key to stop the display.

outframe [port_number]

Displays continuous performance data in frames per second transmitted for all ports. Type q and press the Enter key to stop the display.

errors [port_number]

Displays continuous error counts for all ports. Type q and press the Enter key to stop the display.

50 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Examples

The following is an example of the Show Perf command.

FCSM: user1>: show perf

Bytes/s Bytes/s Bytes/s Frames/s Frames/s Frames/s Port (in) (out) (total) (in) (out) (total)

---- ------- ------- ------- -------- -------- ------- Ext1:0 0 0 0 0 0 0 Ext2:15 0 0 0 0 0 0

Bay1 0 0 0 0 0 0 Bay2 0 0 0 0 0 0 Bay3 0 0 0 0 0 0 Bay4 0 0 0 0 0 0 Bay5 0 0 0 0 0 0 Bay6 0 0 0 0 0 0 Bay7 0 0 0 0 0 0 Bay8 0 0 0 0 0 0 Bay9 0 0 0 0 0 0 Bay10 0 0 0 0 0 0 Bay11 0 0 0 0 0 0 Bay12 0 0 0 0 0 0 Bay13 0 0 0 0 0 0 Bay14 0 0 0 0 0 0

Show Setup command

Displays the current SNMP and system settings.

Authority

User

Syntax

show setup

mfg snmp system

Keywords

mfg

Displays manufacturing information about the switch.

snmp

Displays the current SNMP settings.

system

Displays the current system settings.

Examples

The following is an example of the Show Setup Mfg command.

FCSM: user1> show setup mfg Manufacturing Information

------------------------ BoardSerialNumber P9 BrandName BuildDate Unknown ChassisPartNumber Unknown ChassisSerialNumber P9 MACAddress 00:c0:dd:00:91:02 PlanarPartNumber Unknown SwitchSymbolicName Fibre Channel Switch Module SwitchWWN 10:00:00:c0:dd:00:91:03 SystemDescription Fibre Channel Switch Module SystemObjectID 1.3.6.1.4.1.1663.1.1.1.1.16

The following is an example of the Show Setup Snmp command.

FCSM: user1> show setup snmp SNMP Information

--------------- Contact <sysContact undefined> Location <sysLocation undefined> Description Fibre Channel Switch Module Trap1Address 10.0.0.254 Trap1Port 162 Trap1Severity warning

52 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Trap1Enabled False Trap2Address 0.0.0.0 Trap2Port 162 Trap2Severity warning Trap2Enabled False Trap3Address 0.0.0.0 Trap3Port 162 Trap3Severity warning Trap3Enabled False Trap4Address 0.0.0.0 Trap4Port 162 Trap4Severity warning Trap4Enabled False Trap5Address 0.0.0.0 Trap5Port 162 Trap5Severity warning Trap5Enabled False ObjectID 1.3.6.1.4.1.1663.1.1.1.1.16 AuthFailureTrap False

The following is an example of the Show Setup System command.

FCSM: user1> show setup system System Information

----------------- Eth0NetworkAddress 10.20.8.188 Eth0NetworkMask 255.255.252.0 Eth0GatewayAddress 10.20.8.254 Eth0NetworkDiscovery Static AdminTimeout 30 SecurityEnabled False LocalLogEnabled True RemoteLogEnabled False RemoteLogHostAddress 10.0.0.254

Shutdown command

Terminates all data transfers on the switch at convenient points and closes the Telnet session. Always power cycle the switch after entering this command.

Authority

Admin

Syntax

shutdown

Notes

Always use this command to effect an orderly shutdown before removing power from the switch. Failure to do so could damage the flash memory and the switch configuration.

54 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Test command

Tests switch module ports using internal (SerDes level), external small form-factor pluggable (SFP), and online loopback tests. Internal and external tests require that the switch module port be placed in diagnostic mode. See the “Set Port command” on page 34 for information about changing the port administrative state. While the test is running, the remaining ports on the switch remain fully operational. See “Port testing” on page 117 for more information.

Authority

Admin

Syntax

test

port [port_number] [test_type] cancel status

Keywords

port [port_number] [test_type]

T ests the port given by [port_number] using the test given by [test_type]. If you omit [test_type], Internal is used. [test_type] can have the following values:

Internal (for internal and external ports)

Tests the SerDes. This is the default. The port must be in diagnostics mode to perform thi s test.

External (for external ports only)

Tests both the SerDes and SFP. The port must be in diagnostics mode to perform this test, and a loopback plug must be installed in the SFP.

Online (for internal and external ports)

T ests one online port.

cancel

Cancels the online test in progress.

status

Displays the status of a test in progress, or if there is no test in progress, the status of the test that was executed last.

Examples

To run Internal (SerDes) or External (SFP) port tests, complete the fo llowing steps:

1. To start an admin session, type the following command:

admin start

2. Place the port in Diagnostics mode by typing the following command (x = port number):

set port x state diagnostics

3. Insert the loopback plug into the SFP on the selected port (for external port test only).

4. Choose one of the two types of port loopback tests to run:

• To run an internal loopback test, type the following command:

test x internal

• T o run an e xternal loopback test, type the following command. A loopback plug must be installed for this test to pass.

test x external

✏ NOTE

The external loopback test can be performed only on external switch module ports.

After the test type has been chosen and the command executed, a message on the screen will appear detailing the test results.

5. After the test is run, put the port back int o online state by typing the following command (

number):

set port x state online

6. To verify the port is back online, type the following command. The contents of the AdminState field

should be Online.

show port x

The online node-to-node test can test only one port at a time, and that port must be online and connected to an external device or a blade server Fibre Channel expansion card. To run the online node-to-node test, complete the following steps:

1. To start an admin session, type the following command:

admin start

2. To run the online node-to-node test, type the following command:

test x online

A series of test parameters are displayed on the screen.

3. Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key. The TestLength parameter is the number of frames sent, the FrameSize (256 byte maximum in some cases) parameter is the number of bytes in each frame, and the DataPattern parameter is the pattern in the payload. Before running the test, make sure that the device attached to the port can handle the test parameters.

FCSM (admin) : user1> test x online A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the default value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.

TestLength (decimal value, 1-4294967295) [100 ] FrameSize (decimal value, 36-2148) [256 ] DataPattern (32-bit hex value or 'Default') [Default] StopOnError (True/False) [False ] Do you want to start the test? (y/n) [n]

4. After all parameter values are defined, press the Y key to start the test.

x = port

56 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Uptime command

Displays the elapsed time since the switch was last reset and reset method.

Authority

User

Syntax

uptime

Examples

The following is an example of the Uptime command.

FCSM: user1> uptime Elapsed up time : 0 day(s), 2 hour(s), 28 min(s), 44 sec(s) Reason last reset: NormalReset

User command

Administers or displays user accounts.

Authority

Admin. The List keyword is available with User authority.

Syntax

user

accounts add

ete [account_name]

del list

Keywords

accounts

Displays all user accounts that exist on the switch.

add

Add a user account to the switch. After this command is executed, the administrator will be prompted for the information needed to establish the user account. A switch can have a maximum of 15 user accounts. Account names are limited to 15 characters; passwords are limited to 31 characters.

ete [account_name]

del

Deletes the account name given by [account_name] from the switch.

list

Displays the list of users currently logged in and their session numbers. Provides the same function as the Show Users command. This keyword is valid for User authority and does not require an admin session.

Examples

The following is an example of the User Accounts command.

FCSM (admin) : user1> user accounts Current list of user accounts

-----------------------------

images (admin authority = False) admin (admin authority = True) USERID (admin authority = True)

The following is an example of the User Add command.

FCSM (admin) : user1> user add Press 'q' and the ENTER key to abort this command.

account name (1-15 chars) : user3 account password (4-20 chars) :

please confirm account password: should this account have admin authority? (y/n) [n] : y OK to add user account 'user3' with admin authority? Please confirm (y/n): [n] y

58 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

The following is an example of the User Delete command.

FCSM (admin) : user1> user del user3 The user account will be deleted. Please confirm (y/n): [n] y

The following is an example of the User List command.

FCSM (admin) : user1> user list Current list of users logged in

-------------------------------

admin@OB-session1 - in admin mode admin@OB-session2 user1@OB-session3

Whoami command

Command Displays the account name, session number, and switch domain ID for the Telnet session.

Authority

User

Syntax

whoami

Examples

The following is an example of the Whoami command.

FCSM: user1> whoami User name : admin@OB-session3 Switch name : Fibre Channel Switch Module Switch domain ID: 100 (0x64)

60 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Zone command

Manages zones and zone membership on a switch. The Zone command defines members (ports and devices) for a single switch. Zones are members of zone sets.

Authority

Admin authority and a Zoning Edit session. See the “Zoning command” on page 66 for information about starting a Zoning Edit session. The List, Members, and Zonesets keywords are available with User authority and do not require a Zoning Edit session.

Syntax

zone

add [zone] [members] copy [zone_source] [zone_destination] create [zone]

ete [zone]

del list members [zone] remove [zone] [members] rename [zone_old] [zone_new] type [zone] [zone_type] zonesets [zone]

Keywords

add [zone] [members]

Specifies one or more ports given by [members] to add to the zone named [zone]. A zone can have a maximum of 256 members. [members] can have one of the following formats:

• Domain ID and port number pair (domain ID, port number). Domain IDs and port numbers are in decimal format. Ports are numbered beginning with 0.

• 6-character hexadecim a l device Fibre Channel address (hex)

• 16-character hexadecimal port worldwide name (PWWN) with the format xx:xx:xx:xx:xx:xx:xx:xx.

• Alias name

The application verifies that the [zone] format is correct, but does not validate that such a port exists.

copy [zone_source] [zone_destination]

Creates a new zone named [zone_destination] and copies the membership into it from the zone given by [zone_source].

create [zone]

Creates a zone with the name given by [zone]. An zone name must begin with a letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, &, _, and -. The zoning database supports a maximum of 256 zones.

ete [zone]

del

Deletes the specified zone given by [zone] from the zoning database. If the zone is a member of the active zone set, the zone will not be removed from the active zone set until the active zone set is deactivated.

list

Displays a list of all zones and the zone sets of which they are members. This keyword is valid for User authority and does not require a zoning edit session.

members [zone]

Displays all members of the zone given by [zone]. This keyw ord is available with User authority and does not require a Zoning Edit session.

remove [zone] [members]

Removes the ports given b y [members] from the zone given by [zone]. [members] can hav e one of the following formats:

• Domain ID and port number pair (Domain ID, Port Number). Domain IDs and port numbers are in decimal. Ports are numbered beginning with 0.

• 6-character hexadecim a l device Fibre Channel address (hex)

• 16-character hexadecimal port worldwide name (PWWN) with the format xx:xx:xx:xx:xx:xx:xx:xx.

• Alias name

rename [zone_old] [zone_new]

Renames the zone given by [zone_old] to the zone given by [zone_new].

type [zone] [zone_type]

Specifies the zone type given by [zone_type] to be assigned to the zone name given b y [zone]. If you omit the [zone_type], the system displays the zone type for the zone given by [zone]. [zone_type] can be one of the following:

soft

Name server zone

hardacl

Access control list hard zone

hardvpf

Virtual private fabric hard zone

zonesets [zone]

Displays all zone sets of which the zone given by [zone] is a member. This keyword is av ailable with User authority and does not require a Zoning Edit session.

Examples

The following is an example of the Zone List command.

FCSM: user1> zone list

Zone ZoneSet

------------------ wwn_b0241f zone_set_1

wwn_23bd31 zone_set_1

wwn_221416 zone_set_1

wwn_2215c3 zone_set_1

62 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

wwn_0160ed zone_set_1

wwn_c001b0 zone_set_1

wwn_401248 zone_set_1

wwn_02402f zone_set_1

wwn_22412f zone_set_1

The following is an example of the Zone Members command.

FCSM: user1> zone members wwn_b0241f

Current List of Members for Zone: wwn_b0241f

-------------------------------- 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f

The following is an example of the Zone Zonesets command.

FCSM: user1> zone zonesets zone1

Current List of ZoneSets for Zone: wwn_b0241f

--------------------------------- zone_set_1

Zoneset command

Manages zone sets and zone set membership across the fabric.

Authority

Admin authority and a Zoning Edit session. See the “Zoning command” on page 66 for information about starting a Zoning Edit session. The Active, List, Zones keywords are available with User authority. You must close the Zoning Edit session before using the Activate and Deactivate keywords.

Syntax

zoneset

ivate [zone_set]

act active add [zone_set] [zone_list] copy [zone_set_source] [zone_set_destination] create [zone_set]

ivate

deact

ete [zone_set]

del list remove [zone_set] [zone_list] rename [zone_set_old] [zone_set_new] zones [zone_set]

Keywords

activate [zone_set]

Activates the zone set given by [zone_set]. This keyword deactivates the active zone set. Close the Zoning Edit session before using this keyword.

active

Displays the name of the active zone set. This keyword is available with User authority and does not require a Zoning Edit session.

add [zone_set] [zone_list]

Adds a list of zones and aliases given by [zone_list] to the zone set given by [zone_set]. Zone and alias names are delimited by spaces in [zone_list]. This keyword requires a Zoning Edit session.

copy [zone_set_source] [zone_set_destination]

Creates a new zone set named [zone_set_destination] and copies into it the membership from the zone set given by [zone_set_source]. This keyword requires a Zoning Edit session.

create [zone_set]

Creates the zone set with the name given by [zone_set]. A zone set name must begin with a letter and be no longer than 64 characters. V alid characters are 0-9, A-Z, a-z, &, _, and -. This ke yword requires a Zoning Edit session. The zoning database supports a maximum of 256 zone sets.

ivate

deact

Deactivates the active zone set. Close the Zoning Edit session before using this keyword.

ete [zone_set]

del

Deletes the zone set given by [zone_set]. If the specified zone set is acti ve, the command is suspended until the zone set is deactivated. This keyword requires a Zoning Edit session.

list

Displays a list of all zone sets. This keyword is available with User authority and does not require a Zoning Edit session.

64 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

remove [zone_set] [zone_list]

Removes a list of zones and aliases given by [zone_list] from the zone set given by [zone_set]. Zone and alias names are delimited by spaces in [zone_list]. If [zone_set] is the active zone set, the zone will not be removed until the zone set has been deactivated. This keyword requires a Zoning Edit session.

rename [zone_set_old] [zone_set_new]

Renames the zone set given by [zone_set_old] to the name gi v en by [zone_set_ne w]. You can rename the active zone set. This keyword requires a Zoning Edit session.

zones [zone_set]

Displays all zones that are members of the zone set given by [zone_set]. This keyword is available with User authority and does not need a Zoning Edit session.

Notes

• A zone set must be active for its definitions to be applied to the fabric.

• Only one zone set can be active at one time.

• A zone can be a member of more than one zone set.

Examples

The following is an example of the Zoneset Active command.

FCSM: user1> zoneset active The active ZoneSet is: Beta

The following is an example of the Zoneset List command.

FCSM: user1> zoneset list Current List of ZoneSets

----------------------- alpha beta

The following is an example of the Zoneset Zones command.

FCSM: user1> zoneset zones ssss Current List of Zones for ZoneSet: ssss

--------------------------------- zone1 zone2 zone3

Zoning command

Opens a Zoning Edit session in which to create and manage zone sets and zones. See the “Zone command” on page 61” and the “Zoneset command” on page 64” for information about managing zone and zone sets.

Authority

Admin. The List keyword is available with User authority.

Syntax

zoning

active cancel clear edit history limits list restore save

Keywords

active

Displays membership information for the active zone set including member zones and zone members.

cancel

Closes the current Zoning Edit session. Any unsaved changes are lost.

clear

Clears all inactive zone sets from the volatile edit copy of the zoning database. This ke yword does not affect the nonv olatile zoning database. Ho we v er, if you enter the Zoning Clear command followed by the Zoning Save command, the nonvolatile zoning database will be cleared from the switch. The preferred method for clearing the zoning database from the switch is the Reset Zoning command.

edit

Opens a Zoning Edit session.

history

Displays a history of zoning modifications including the following:

• Time of the most recent zone set activation or deactivation and the user who performed it

• Time of the most recent modifications to the zoning database and the user who made them.

• Checksum for the zoning database.

limits

Displays the maximum limits imposed on the zoning database for the number of zone sets, zones, aliases, members per zone, members per alias, and total members.

list

Lists all fabric zoning definitions. This keyword is available with User authority.

restore

Reverts the changes to the zoning database that have been made during the current Zoning Edit session since the last Zoning Save command was entered.

save

Saves changes made during the current Zoning Edit session. The system will inform you that the zone set must be activated to implement any changes. This does not apply if you entered the Zoning Clear command during the Zoning Edit session.

66 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Examples

The following is an example of the Zoning Edit command.

FCSM: user1> admin start FCSM (admin) : user1> zoning edit FCSM (admin-zoning) : user1> . . FCSM (admin-zoning) : user1> zoning cancel Zoning edit mode will be canceled. Please confirm (y/n): [n] y FCSM (admin) : user1> admin end

The following is an example of the Zoning List command.

FCSM: user1> zoning list Active ZoneSet Information

ZoneSet Zone ZoneMember

------------------------------- wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f

wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31

wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16

wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15:c3

Configured Zoning Information

ZoneSet Zone ZoneMember

------------------------------- wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f

wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31

wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16

wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15:c3

68 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Using the SAN Utility

You can use the SAN Utility application to access and configure switch modules. For information about installing, uninstalling, and starting the SAN Utility application, see the Fibre Channel Switch Module Installation Guide. The SAN Utility application can be installed on an SBCE blade server or an external network management workstation configured with one of the operating systems described in the Fibre Channel Switch Installation Guide.

To manage your switch modules and fabrics, the SAN Utility application provides two basic windows: T opology a nd Faceplate. The SAN Utility user interf ace, its elements, and the tasks that you can perform from the Faceplate window and Topology window are described in this chapter.

Important: Before you configure your switch module, be sure that the management modules in your SBCE unit are properly configured. In addition, to access and manage your switch module from an external environment, you might need to enable certain features, such as the external ports and external management

over all ports. See the applicable Intel

on the Intel

Server Chassis SBCE Resource CD for more information. For more detailed information about

configuring your switch module, see the Intel Installation Guide on the Resource CD.

SAN Utility user interface

The Topology window and Faceplate window share the following common elements:

• Menu bar

•Toolbar

• Fabric tree

•Graphic window

• Data window and tabs

• Working Status indicator The T opology window displays all of the switch modules that are enabled and the connections between switch

modules and other Fibre Channel devices, as shown in Figure 1.

Blade Server Chassis SBCE Installation and User’s Guide publications

Blade Server Fibre Channel Switch Module SBCEFCSW

Figure 1. Topology window

The Faceplate window displays the front of a single switch module and its active ports, as shown in Figure 2

Figure 2. Faceplate window

Menu bar

The menu bar is displayed at the top of the Faceplate window and Topology window. Depending on which window is open, the menu bar has similar menu selections. Figure 3 shows menu items that are available in the Topology window and the Faceplate window. In the figure, menu items available from the faceplate window, but not in the Topology window are shown with a gray background.

Figure 3. Menu bar selection examples

70 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Some menu selections have shortcut keys as shown in Table 14.

Table 14. Menu shortcut keys

Shortcut key Menu selection

F5 Ctrl+O

View ” Refresh File ” Open View File

In addition to the menu bar, both the Topology and Faceplate windows hav e conte xt-sensiti v e menus that open when you click in the graphic window with the right mouse button. See “Opening the Faceplate window and pop-up menus” on page 76 for more information about these pop-up menus.

Toolbar

The toolbar consists of a row of graphical buttons that you can use to access SAN Utility functions as shown and described in Table 15 The toolbar buttons are an alternative method to using the menu bar.

Table 15. Toolbar buttons

Toolbar button Toolbar button name Description

Add Fabric Adds a new fabric

Open View File Opens an existing fabric view file

Save View As Saves the current fabric view to a file

Refresh Polls the fabric to update the Topology or

Faceplate window with the current information

Help Topics Opens the online help

Edit Zoning Opens the Edit Zoning window (available only in

the Faceplate window)

Fabric tree

The fabric tree, in the FC Fabric pane, lists the managed fabrics and their switch modules. To adjust the window, click and drag the moveable window border. An entry handle to the left of an entry in the tree indicates that you can expand the entry . When you click the handle or double-click the entry, the entry e xpands to show its member switches. These fabric tree elements are shown in Figure 4 on page 72

Figure 4. Fabric tree

Each fabric tree entry has a small icon next to it that uses color to indicate the following operational status:

• A green switch module entry icon indicates that the switch is in normal operation.

• A green switch module entry icon indicates that the switch has a communications failure.

• A red switch

• A blue switch module entry icon indicates that the switch status is Unknown or that security is enabled on the switch module but security is disabled on the fabric management switch.

• An amber switch module entry icon indicates that the sw itch is operational with errors.

You can use the fabric tree to access any f abric or switch module using the Topology or Faceplate window . You can click a fabric entry to open the T opology window from the fabric tree. You can click a switch module entry to open the Faceplate window from the fabric tree.

Graphic window

The graphic window as shown in Figure 1 on page 69 shows graphic information about fabrics and switch modules such as the fabric topology and the switch faceplate. To adjust the window length, click and drag the window border that it shares with the data window.

Data window and tabs

The data window as shown in Figure 2 on page 70 displays a table of data and statistics associated with the selected tab. Use th e scroll bar t o browse through the data. The window length can be adjusted by clicking and dragging the border that it shares with the graphic window.

To adjust the column width, move the pointer over the column heading border shared by two columns until a right/left arrow graphic is displayed. Click and drag the arrow to the desired width. The data window tabs show options for the types of information that you can display in the data window. These options vary depending on the display.

72 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Working status indicator

The working status indicator as shown in Figure 1 on page 69 is in the lower-right corner of the Topology window and shows when the network management workstation is exchanging information with the fabric. As conditions change, the fabric forwards this information to the network management workstation where it is reflected in the various displays.

Using the Topology window

The Topology window shown in Figure 5 polls the selected fabric and displays its topology. switch modules and interswitch links (ISL) are displayed in the graphic window and use color to indicate status. The follo wing functional elements are displayed in the Topology window when you click on the Data window tabs:

• Switch module and link status

• Working with switch modules and links

• Topology data windows

Figure 5. Topology window

Fibre Channel switch module and link status

The Fibre Channel switch module icon shape and color provide information about the switch and its operational state. In the Topology window, lines represent links between switch modules. See Table 16 for Fibre Channel switch module and link status and “Fabric status” on page 80 for more information about other Topology window icons.

Table 16. Fibre Channel switch module and link status indicators

Switch module icon color Status

Green Normal Fibre Channel switch operation Amber Operational with errors Red Inactive or Fibre Channel switch failure Blue Unknown Fibre Channel device

Working with switch modules and links

Switch module and link icons are selectable and moveable and serve as access points for other windows and menus. You select switch modules and links to display information, modify configurations, or delete them from the window. The context-sensitive pop-up menus are accessible through the switch module and link icons.

Click a switch module or link in the graphic window to display its status in the data window. To select multiple switch modules or links, hold down the Ctrl key while selecting. When no switch modules or links are selected, information about all switch modules is displayed. To deselect a switch module or link that is currently selected, click the switch or link.

Different switch module icons will be displayed depending on the different switch vendor products present in the attached fabric. See Table 17 on page 81 for a list of switch module icons and vendors. Attached switch modules that are not manageable through the SAN Utility will be displayed as “third-party manageable” switch icons. The topology configuration in Figure 6 shows an example of a switch fabric with third-party switch modules.

Figure 6. Switch fabric showing third-party manageable switch modules

Arranging switch modules in the window

You can use the following two methods to arrange individual switch module icons:

• To move an individual switch module icon, click and drag the icon to another location in the graphic window. Links stretch or contract to remain connected.

• To arrange all switch module icons in the Topology window, click

The Toggle Auto Layout check box in the View menu is selected by default so that the SAN Utility can arrange the icons when you select Layout Topology.

You can save a custom arrangement, or layout, and restore that layout during a SAN Utility session. To create a custom arrangement, arrange the icons; then, click View / Remember Layout. To restore the saved layout, click View, clear the Toggle Auto Layout check box, and click Layout Topology.

View / Layout Topology.

74 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Selecting switch modules and links

Selected switch module icons are highlighted in violet. Selected ISLs are highlighted in amber . You can select switch modules and links by performing the following tasks:

• To select a switch module or a link, click the icon or link.

• To select multiple switch modules or links, hold down the Ctrl key and click the switch modules or links that you want.

• To select all switch modules or links, right-click in the graphic window background. Click

Switches or click All Links

T o cancel a selection, press and hold the Ctrl ke y, and select the item again. T o cancel multiple selections, click in the graphic window background.

from the pop-up menu.

Topology data window tabs

The Topology Data window contains four tabs at the bottom of the window. When you click a tab, the following information is displayed:

•

Name Server - Click the Name Server tab to display all devices that are logged with the name server and their location within the current fabric configuration. See

on page 108 for more information about your configuration.

•

Active Zoneset - Click the Active Zoneset tab to display the active zone set for the fabric, including zones and their member ports. See information about this data window . See

and zones.

Switch - Click the Switch tab to display the current network and switch module configuration

•

data for the selected switches. See Link - Click the Link tab to display the current link status for the selected switch modules in the fabric.

•

“Switch Data window” on page 94 for more information.

“Active Zoneset Data window” on page 82 for more

“Zoning a fabric” on page 82 for information about zone sets

“Name Server Data window”

Select All

Using the Faceplate window

The Faceplate window shown in Figure 7 and described in this section displays the switch module name and operational state and the port status. The following functional elements are displayed in the Faceplate window when you click on the Data window tabs:

• Port views and status

• Working with ports

• Faceplate data windows

Figure 7. Faceplate window

Opening the Faceplate window and pop-up menus

The Faceplate window shows the front of a single switch module and its ports. You can open the Faceplate window and pop-up menus when you are in the Topology window by performing the following tasks:

• T o open the Faceplate windo w when vie wing the Topology window , click a switch module entry or icon in the fabric tree, or double-click the switch module graphic.

• To open the fabric pop-up menu when viewing the Topology window, right-click the graphic window background. The fabric pop-up menu displays selections to refresh the fabric, select all switch modules, select all links, or layout topology .

• To open the switch module pop-up menu when viewing the Topology window, right-click the switch module icon in the graphic window. The switch pop-up menu displays selections to refresh the switch, delete the switch from the display, open the Switch Properties window, or open the Network Properties window.

• To open the link pop-up menu, right-click the link. The Link pop-up menu displays a selection to delete the link from the display.

• To open a Faceplate window pop-up menu, right-click the faceplate graphic in the Graphic window. The faceplate pop-up menu displays selections to refresh the switch module, select all ports, manage switch, port, and network properties, extend credits, and run the Port Loopback tests.

Port views and status

Port color and text pr ovid es information about the port and its operational state. Green indicates that the port is active, and gray indicates that the port is inactive. The Faceplate window displays the following views of port status corresponding to the View menu options in the Faceplate window:

• Port mode

• Port state

• Port speed

• Port media

See “Monitoring port status” on page 103 for more information about these displays.

Working with ports

Ports are selectable and serve as access points for other windows and menus. You select ports to display information about them in the data window or to modify them. You cannot use the SAN Utility to select internal bays and external ports at the same time; you must select either internal bays or external ports. Context-sensitive pop-up menus and properties windows are acces sible through the Faceplate windo w and port icons.

Selecting ports

When you select a port, the port is highlighted with a white border. You can select ports in the following ways:

• To select one port, click the port in the Faceplate display.

• To select a range of either internal or external consecutive ports, select a port and then press and hold the shift key and select another port. The application selects both end ports and all ports in between in port number.

• To select several nonconsecutive ports, hold the Ctrl key while selecting ports.

• To select all external ports, right-click anywhere on the switch module faceplate, and select

Ports from the pop-up menu. To select all internal ports, click any blade server and select All Ports

from the pop-up menu.

To cancel a selection, press and hold the Ctrl key and select it again.

Select All

76 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Opening pop-up menus

You can manage the switch module and its ports using the following methods:

• To open the pop-up menu, right-click anywhere in the graphic window. If no ports are selected, port specific tasks are unavailable in the menu.

• To select one or more ports and open the Port pop-up menu, right-click a port.

Faceplate data window tabs

The Faceplate Data window contains six tabs at the bottom of the display. When you click a tab, the following information is displayed:

•

Name Server - Click the Name Serv er tab to display all devices connected to the switch module that

are logged with the name server.

•Switch

• Port Statistics

• Port Information

• Configured Zonesets

•Alarm Log

- Click the Switch tab to display the current switch module configuration data.

- Click the Port Stats tab to display the port performance data for the selected port.

- Click the Port Info tab to display the port detail information for the selected port.

- Click the Configured Zonesets tab to display all zone sets, zones, and zone

membership in the zoning database.

- Click the Alarm Log tab to display the system error information.

Managing fabrics

This section describes the following four main tasks for managing fabrics:

• Setting up security

• Managing the fabric database

• Displaying fabric information

• Zoning a fabric

Setting up security

Access to a switch module and permission to configure a switch is managed through user accounts created by a fabric administrator. A user account consists of an

account name, a password, and an authority level. The authority level determines whether an account can merely monitor the switch module and fabric activity (User authority), or change switch module configurations (Administrative authority). See “User command” on page

58 for information about administrating user accounts. Fabric security determines the enforcement of user accounts on a switch module. A fabric administrator can

enable or disable the fabric security on a switch module using the Set Setup System command. If fabric security is disabled (default), you can use the SAN Utility to log in to a switch module without an

account name and password. The Login name and Password fields in the Add a Fabric window are ignored, and you are granted Admin authority. If fabric security is enabled, you must enter an account name and password to log in to a switch module and add the fabric to the workspace. Having successfully added a fabric, you can perform only those tasks in the SAN Utility that are granted by the authority level for that account. All switch modules in a fabric should use the same fabric security value. See “Set Setup command” on page 35 for information about the System keyword and the Security Enable parameter.

✏ NOTE

A switch module supports a combined maximum of 15 active login sessions. This includes SAN Utility in-band and out-of-band login attempts, Telnet out-of-band login attempts, and SNMP out-ofband login sessions. Of this 15, there can be a maximum of 10 SAN Utility login attempts included in the 15 total attempts. Additional logins are refused.

Managing the fabric database

A fabric database contains the set of fabrics that you have added during a SAN Utility session. Initially, a Topology window with an empty fabric database opens. This section describes the following fabric database management tasks:

• Adding a fabric

• Removing a fabric

• Opening a fabric view file

• Saving a fabric view file

• Rediscovering a fabric

• Adding a new switch module to a fabric

• Replacing a failed switch module in a fabric

• Deleting switch modules and links

Adding a fabric

Complete the following steps to add a fabric to the database:

1. In the Faceplate window, click The Add a New Fabric window opens, as shown in Figure 8

Fabric / Add Fabric.

Figure 8. Add a New Fabric window

2. In the

3. In the

4. In the

Fabric name field, type a fabric name. IP address field, type the IP address of the switch module through which to manage the fabric. Login name field, type the initial default login ID, USERID. In the Password field, type

the initial default password, PASSW0RD (the sixth character is a zero, not the letter O). The user ID and password are case sensitive.

✏ NOTE

The password is for the switch module and is stored in the switch firmware. You are not required to type a user ID or password if security is disabled. See “Setting up security” on page 77. See “Set Setup command” on page 35 for information about the Set Setup commands in the Telnet section to log in, and obtain password and security information.

5. Click

Removing a fabric

Complete the following steps to delete a fabric file from the database:

1. Select a fabric in the fabric tree.

2. In the Faceplate window, click

78 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Add fabric.

Fabric / Remove Fabric.

Opening a fabric view file

Complete the following steps to open an existing fabric view file:

1. In the Faceplate window, click If there is a change to the fabric you are using, you are prompted to save the changes to the view file

before opening a different view file. The Open View window opens.

2. In the Open View window, type the name of the file you want to open.

3. Type a file password if necessary.

4. Click

Load View File. If the fabric has changed, you are prompted to save the file before opening the

new view.

File / Open View File, or click the Open icon.

Saving a fabric view file

Complete the following steps to save a fabric view file:

1. In the Faceplate window, click The Save View window opens.

2. In the Save View window, type a new file name.

3. Click

4. Type a file password, if necessary.

OK.

File / Save View As or click the Save icon.

Rediscovering a fabric

After making changes or deleting switch modules from a fabric view, refresh the fabric configuration. Use the Rediscover Fabric option to clear the current fabric information that is displayed and rediscover the switch module information. To rediscover a fabric, in the Faceplate window, click Fabric / Rediscover Fabric.

Adding a new switch module to a fabric

After you install a switch module into your Blade Server Chassis SBCE, the switch uses the default fabric configuration settings. The default fabric configuration settings are as follows:

• Fabric zoning is sent to the switch module from the fabric.

• All external ports (0,15) are GL_Ports; all internal ports (1 through 14) are F_Ports.

• The default IP addresses are: For switch module bay 3:

192.168.70.129

For switch module bay 4:

192.168.70.130

Complete the following steps to add a new switch module to a fabric and not make changes to the default fabric configuration settings:

1. If the switch module is not new, to reset the switch to the factory configuration, in the Faceplate window, click

Switch / Restore Factory Defaults.

2. If you want to manage the switch module through the Ethernet port, configure the network SNMP configuration using the Network Properties window. For more information, see “Network properties” on page 100.

3. Configure any special switch settings.

✏ NOTE

To prevent communication with other switch modules in the fabric until the new switch is configured, in the Zoning Config window, click None in the Default Visibility field. For more information, see “Zoning configuration” on page 84.

4. Connect the interswitc h links (ISL), but do not connect the devices.

5. In the Port Properties window, configure the port types for the new switch (GL_Port, TL_Port, Donor).

6. Connect the Fibre Channel devices to the switch module.

7. In the Edit Zoning window, make the necessary zoning changes.

Replacing a failed switch module in a fabric

Complete the following steps to replace a failed switch module for which an archive is available. See “Restoring a switch module” on page 121 and “Archiving a switch module” on page 102 for more information.

1. Remove the failed switch module. For more information, see the

2. Install the new replacement switch module. For more information, see the

3. Log in to the fabric through the replacement switch module. In the Topology window, select the replacement switch module from the fabric tree.

4. Click

5. In the Restore Switch window, type a name or select the archived switch configuration file to copy to the

6. Click

Switch / Restore.

The Restore Switch window opens.

switch module. For more information, see “Archiving a switch module” on page 102.

OK to write the configuration file to the switch module.

Installation Guide.

Deleting switch modules and links from the Topology display

The SAN Utility does not automatically delete switch modules or links that have failed or that are physically removed. In this case, you can delete switch modules and links in the T opology windo w to bring the display up to date. If you delete a switch or a link that is still active, the SAN Utility restores it automatically. You can also refresh the display.

Complete the following steps to delete a switch module in the Topology window:

1. Select one or more switch modules in the Topology window.

2. Click

Complete the following steps to delete a link:

1. Select one or more links in the Topology window.

2. Click

Switch / Delete.

Displaying fabric information

The Topology window is the primary tool for monitoring a fabric. The graphics window of the Topology window provides status information for switch modules, interswitch links, and the Ethernet connection to the network management workstation.

The data window tabs show name server, switch, and active zone set information. The Active Zoneset tab shows the zone definitions for the active zone set. See “Switch Data window” on page 94 and “Name Server Data window” on page 108 for information about the Switch Data and Name Server Data windows.

Fabric status

The fabric updates the Topology and Faceplate windows by forwarding changes in status to the network management workstation as they occur. Use the fabric to update the display status, or you can refresh the display at any time. To refresh the Topology window, use on e of the fo llowing methods:

• In the Topology window, click

• Click

•Press the F5 key.

• Right-click anywhere in the background of the Topology window. Select

The T opology window displays switch module and status icons that provide status information about switches, interswitch links, and the Ethernet connection. The switch module icons indicate different vendor switches and switch types. The switch module status icons, displayed on the left side of a switch, vary in shape and color. Each switch module that is managed by an Ethernet Internet protocol (IP) has a colored Ethernet icon that is

View / Refresh.

up menu.

Refresh.

Refresh Fabric from the pop-

80 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

displayed on the right side of the switch. A green Ethernet icon indicates normal operation, amber indicates operational with errors, and red indicates inactive or failure. Table 17 on page 81 shows the different switch module icons and their descriptions .

✏ NOTE

Different switch module icons are displayed depending on the different switch vendor products presented in the attached fabric. For a list of switch module icons and vendors, see Table 17 on page 81 Attached switch modules that are not manageable through the SAN Utility are displayed as thirdparty manageable switch icons. The topology configuration in Figure 6 on page 74 shows an example of a switch fabric with third-party switch modules.

Table 17. Topology window switch module and status icons

Switch module icon Description

Fibre Channel switch module

QLogic 8-port Fibre Channel switch module

QLogic16-port Fibre Channel switch module Inrange switch module

McData switch module Brocade switch module Other third-party switch modules

Switch communication normal (green)

Switch is operational with errors (amber)

Switch communication interrupted (red)

Switch management communication unknown (blue)

Fabric management switch Ethernet connection normal (green)

Fabric management switch Ethernet connection critical (red)

Fabric management switch Ethernet connection warning (amber)

Active Zoneset Data window

The Active Zoneset Data window displays the zone membership for the active zone set that resides on the fabric management switch. The active zone set is the same on all switch modules in the fabric. You can confirm this by adding a fabric through another switch module and compari ng Active Zone Set displays.

To open the Active Zoneset Data window, click the Active Zoneset tab below the data window in the Topology window. See “Zoning a fabric” for more information about zone sets and zones. See “Configured Zonesets Data window” on page 96 for information about the zone set definitions on a specific switch module.

The Active Zoneset data window, shown in Figure 9 uses display conventions for expanding and contracting entries that are similar to the fabric tree. An entry handle to the left of an entry in the fabric tree indicates that you can expand the entry. Click this handle or double-click the following entries to expand or contract them:

• A zone set entry expands to show its member zones.

• A zone entry expands to show its member ports.

• A port entry expands to show the port Fibre Channel address.

• A Fibre Channel address entry expands to show the port worldwide name.

Figure 9. Active Zonesets window

Zoning a fabric

Fibre Channel fabrics use zoning to restrict or extend access to devices in the fabric. A zone is a named group of devices that can communicate with each other.

You can use zoning to divide the ports and devices of the fabric into zones for more efficient and secure communication among functionally grouped nodes. You can set the Auto Save and Default Visibility zoning configuration parameters using the SAN Utility or the Set Config Zoning command. See “Auto save” on page 84 for information about the Auto Save parameter, see “Default visibility” on page 84 for information about the Default Visibility parameter, and see “Using the Zoning Config window” on page 85 for information about the Set Config Zoning command.

Zoning concepts

The following zoning concepts provide some context for the zoning tasks described in this section:

•Zones

• Aliases

•Zone sets

• Zoning database

• Zoning configuration

82 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Zones

A zone is a named group of ports or devices that can communicate with each other. Membership in a zone is defined by port number, device Fibre Channel address, or device World Wide Name (WWN). Zone members can communicate only with members of the same zone. Zones can overlap; that is, a port or device can be a member of more than one zone.

There are three zone types that are supported but have restrictive levels of communication. These zone types are:

• Soft zone

• Access control list (ACL) - hard zone

• Virtual private fabric (VPF) - hard zone

Soft zoning

Soft zoning divides the fabric for purposes of controlling discovery. Members of the same soft zone automatically discover and communicate freely with all other members of the same zone. The soft zone boundary is not secure; traffic across soft zones can occur if addressed correctly. Soft zones that include members from multiple switch modules need not include the ports of the interswitch links. Soft zone boundaries yield to ACL and VPF zone boundaries. Soft zones can overlap; that is, a port can be a member of more than one soft zone. Membership is defined by Fibre Channel address, port ID and domain ID, or worldwide name. Soft zoning supports all port modes.

Access control list zones

Access control list (ACL) zoning divides the fabric for purposes of controlling discovery and inbound traffic. ACL zoning is a type of hard zoning that is hardware enforced. This type of zoning is useful for controlling access to certain devices without totally isolating them from the fabric. Members can communicate with each other and transmit outside the ACL zone but cannot receive inbound traffic from outside the zone. The ACL zone boundary is secure against inbound traffic. ACL zones can overlap; that is, a port can be a member of more than one ACL zone. ACL zones that include members from multiple switch modules need not include the ports of the interswitch links. ACL zone boundaries supersede soft zone boundaries but yield to VPF zone boundaries. Membership can be defined only by port ID and domain ID. ACL zoning supports all port modes except TL_Ports.

Virtual private fabric zones

Virtual private fabric (VPF) zoning divides the fabric for purposes of controlling discovery and both inbound and outbound traffic. This type of zoning is useful for providing security and reserving paths between devices to guarantee bandwidth. VPF zoning is a type of hard zoning that is hardware enforced. Members can transmit to and receive only from members of the same VPF zone. The VPF zone boundary is secure against both inbound and outbound traffic. VPF zones that include members from multiple switch modules must include the ports of the interswitch links. VPF zones cannot overlap; that is, a port can be a member of only one VPF zone. VPF zone boundaries supersede both soft and ACL zone boundaries. Membership can be defined only by port ID and domain ID. VPF zoning supports all port modes.

✏ NOTE

Domain ID conflicts can result in automatic reassignment of switch module domain IDs. These reassignments are not reflected in zones that use domain ID and port number pairs or Fibre Channel addresses to define their membership . Be sure to reconf igure zones that are affected by a domain ID change. To prevent zoning definitions from becoming invalid when the membership is defined by domain ID/port number or Fibre Channel address, you must lock domain IDs.

Aliases

T o mak e it easier to add a group of ports or devices to one or more zones, you can create an alias. An alias is a named set of ports or devices that are grouped together for convenience. Unlike zones, aliases impose no communication restrictions between its members. You can add an alias to one or more zones. However, you cannot add a zone to an alias, nor can an alias be a member of another alias.

Zone sets

A zone set is a named group of zones. A zone can be a member of more than one zone set. All zones that are not members of a zone set belong to the orphan zone set. The orphan zone set is saved to the switch module. Each switch module in the fabric maintains its own zoning database containing one or more zone sets. This zoning database resides in nonvolatile or permanent memory and is therefore retained after a reset. For information about displaying the zoning database, see “Configured Zonesets Data window” on page 96.

To apply zoning to a fabric, select a zone set and activate it. When you activate a zone set, the switch module distributes that zone set to every switch in the fabric. Therefore, every switch module in the fabric will have identical active zone sets. For information about displaying the active zone set, see “Active Zoneset Data window” on page 82.

Zoning database

Each switch module has its own zoning database. The zoning database is made up of all aliases, zones, and zone sets that have been created on the switch or received from other switch modules. The switch module maintains two copies of the zoning database: one copy is maintained in temporary memory for editing purposes; the second copy is maintained in permanent memory. Zoning database edits are made on an individual switch basis and are not propagated to other switch modules in the fabric when saved.

The Auto Save zoning configuration parameter controls whether the temporary zoning database is automatically saved in permanent memory. For more information about the Auto Save parameters, see “Zoning configuration.”

The zoning limits for a fabric are:

• Maximum number of zonesets is 256

• Maximum number of zones is 256

• Maximum number of aliases is 256

• Maximum number of members per zone is 2000

• Maximum number of members per alias is 2000

• Maximum total number of zone and alias members is 2000

• Maximum total number of zone set members is 1000

Zoning configuration

You can set the zoning configuration parameters using the SAN Utility or the Set Zoning Config command. For information about zoning configuration using the SAN Utility, see “Using the Zoning Config window” on page 85 and “Set Config command” on page 26.

The following parameters make up the zoning configuration:

• Auto Save

• Default Visibility

Auto save

The Auto Save parameter determines whether changes to the active zone set that a switch module receives from other switches in the fabric are saved to permanent memory on that switch module. Changes are saved when an updated zone set is activated. Zoning changes are always saved to temporary memory. However, if Auto Save is enabled, the switch module firmware saves changes to the active zone set in both temporary and permanent memory. If Auto Save is disabled, changes to the active zone set are stored only in temporary memory.

Default visibility

The Default Visibility parameter determines the level of communication that is permitted between devices when there is no active zone set. The default visibility parameter can be set differently on each switch module. When default visibility is enabled (set to All) on a switch module, all ports on the switch can communicate with all ports on switch modules that also have the Default Visibility parameter set to Enabled. When default visibility is disabled (set to None) on a switch module, none of the ports on that switch module can communicate with any other switch in the fabric.

84 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Using the Zoning Config window

Use the Zoning Config window to change the Auto Save and Default Visibility configuration parameters. Complete the following steps to open the Zoning Config window and change configuration parameters:

1. In the Faceplate window, click Zoning / Edit Zoning Config.The Zoning Config window opens.

Figure 10. Zoning Config window

2. Make the necessary changes to the Auto Save and Default Visibility fields and click OK.

Restoring default zoning

Restoring the default zoning clears the switch module of all zoning definitions. Complete the foll owing steps to restore the default zoning for a switch module.

Attention: The use of this command will deactivate any active zone set. If the switch module is not isolated from the fabric, this command will deactivate the active zone set for the entire fabric.

1. In the Faceplate window, click

2. Click

OK to confirm that you want to restore default zoning and save changes to the zoning database.

Zoning / Restore Default Zoning.

Merging fabrics and zoning

If you join two fabrics, the active zone sets from the two fabrics attempt to merge. The fabrics can consist of a single switch module or many switches already connected together. The switch modules in the two fabrics attempt to create a new active zone set containing the union of the active zone set of each fabric. The propagation of zoning information affects only the active zone set, not the configured zone sets.

Zone merge failure

If a zone merge is unsuccessful, the interswitch links between the fabrics will isolate because of a zone merge failure, which generates an alarm log entry. The reason for the E_Port isolation can also be determined by viewing the port.

information. See the “Port Information Data window” on page 96 and the “Show command” on page 38 (Port keyword).

A zone merge will fail if the two active zone sets have member zones with identical names that differ in content or type. For example, consider Fabric A and Fabric B, each with a zone in its active zone set named “ZS1.” Fabric A “ZS1” contains a member specified by Domain ID 1 and Port 1; Fabric B “ZS1” contains a member specified by Domain ID 1 and Port 2. In this case, the merge fails, and the interswitch links between the fabrics are isolated.

Zone merge failure recovery

When a zone merge failure occurs, the conflict that caused the failure must be resolved. You can correct a failure due to a zone conflict by deactivating one of the acti v e zone sets or editing the conflicting zones so that their membership is the same. You can deactivate the active zone set on one switch module if the active zone set on the other switch accurately defines your zoning needs. If not, you must edit the zone memberships and reactivate the zone sets. F or information about adding a nd removing zone members, see “ Managing zones” on page 89. To permit the fabrics to join, reset the ports that were isolated. See “Resetting a port” on page 113.

Using the Edit Zoning window

Use the Edit Zoning window to edit the zoning database for a specific switch module. To edit the zoning database, in the Faceplate window, click Zone / Edit Zoning. The Edit Zoning window opens.

✏ NOTE

You can make changes only to an active zone set, which is stored in flash (nonvolatile) memory and retained after setting a switch module.

Figure 11. Edit Zoning window

The Edit Zoning window displays a Zone Sets tree in the left pane and a Port and Device (or members) tree in the right pane, as shown in Figure 11 Both trees use display conventions similar to the fabric tree for expanding and contracting zone sets, zones, and ports. An expanded port shows the port Fibre Channel address; an expanded address shows the port worldwide name. You can select zone sets, zones, and ports in the following ways:

• Click a zone, zone set, or port icon.

• Right-click to select a zone set or zone and open the corresponding pop-up menu.

• Hold down the Shift key while clicking several consecutive icons.

• Hold down the Ctrl key while clicking several nonconsecutive icons.

Using the toolbar, pop-up menus, or a drag-and-drop method, you can create and manage zone sets and zones in the zoning database. Click Apply to save your changes to the zoning database without closing the window. Click OK to save your changes to the zoning database and close the window.

86 Intel Blade Server Fibre Channel Switch Module SBCEFCSW / FC Expansion Card SBFCM Guide

Intel SBFCM, SBCEFCSW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual